0x0000008E early upward blue screen

original title: Blue screen 0x0000008E, desperately need help!

Ello, been some frustrating problems with my computer. I am running Windows Vista Home Premium
Version: 6.0.6000 build 6000

It is a desktop HP Pavilion I had to replace the motherboard for.
Motherboard: Gigabyte GA-G41M-ES2L
Processor: Intel Pentium Dual CPU E2180

So, whenever I try to log in normally the computer immediately blue screens with this message STOP: 0x0000008E (0xC0000005, 0x821F5C19, 0xA5BCB91C, 0x00000000). The computer starts in safe mode but. Here are the steps I took to solve the problem. I used Hiren's Boot CD and just about every program that comes with it in the hope that it would be just a problem of virus/spyware/malware (including GMER, SmitFraud, Malwarebytes and ComboFix).

I disconnected the memory and attempt to start the computer to the top, same problem. Does a memtest as well. Then I unplugged and the computer on everything that was connected to the computer. The graphics card is shipped so I couldn't actually test this. Tried to update the chipset, the graphics card, drivers audio and everything but as soon as I log on the drivers are always roll would be back in their earlier version, which I find very strange. I also used my Windows Vista disk to try to repair the installation and do a chkdsk/r. I would like to provide information dump, but for some reason any there is no file in my minidump folder. Whew, sorry for the long explanation, but I thought I would get everything that I realized that I suppose would have suggested road.

Hello

Please check your settings here:

Configuration-system sign - on the side left Advanced System Settings - Advanced tab.

Startup and recovery - settings - system failure - check the box to write an event to the system log

Uncheck the automatic reboot

Make sure to write debugging is set to small minidump

and the default folder should look like % SystemRoot%\Minidump.

How to configure Windows to create MiniDump on BSOD files
http://blog.NirSoft.NET/2010/07/27/how-to-configure-Windows-to-create-minidump-files-on-BSOD/

------------------

We can analyze the minidumps as indicated in the previous answer but there is a very
good luck the question is associated with memory.

You can access in Safe Mode - several times F8 tap that you start?

If necessary use the methods below to run the Startup Repair to see if you have better access.

Then go back and use the methods in the Troubleshoot utility above to see if you can solve
the question.

-----------

If you do not have a Windows 7 disc, you can borrow a friends because they are not a copy
protected. The manufacturer of your system will also sell the physical DVD cheap since you already
Clean Windows. You can also do an ERD on another computer.

Try the Startup Repair - (if at anytime, benefit you from some, but not full access coming to Windows
return and then try to startup repair.)

How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.html

What are the system recovery options in Windows 7?
http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

Try the disk Options recovery or Windows 7 startup repair.

How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.html

Also from the command PROMPT on the Console (if possible) recovery or a Windows 7 disc

Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

sfc/scannow

How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

Then run checkdisk (chkdsk).

How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html

Retry After Chkdsk startup repair.

If after those you can try the system restore to fashion without failure or the valuation or Windows 7
disc.

How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html

--------------------------------------------------------------------

If you need to repair disks - these help repair Windows not re-install.

How to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

======================================

If necessary:

What to do if Windows does not start correctly
http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly

How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.html

What are the system recovery options in Windows 7?
http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

How to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.html

I hope this helps.

Rob Brown - Microsoft MVP - Windows Expert - consumer: bike - Mark Twain said it right.

Tags: Windows

Similar Questions

  • Satellite 2410-404: blue screen STOP: 0x0000008E TVALD. SYS

    Hello
    last night I tried the WinXP "verifier.exe" tool to check unverified in WinXP drivers.
    My system worked very well until this try. After the first reboot, the system load until the home screen where I choose my account (Administrator rights) to load my profile. After the boot process slows down upwards, only windows processes are shown in the lower right bar (icon of sound system, network) and after a while, there is a blue screen with the following information:

    STOP: 0X0000008E (0XC0000005, 0XF89A742C, 0XF3DFDB50, 0X00000000)
    TVALD. SYS - address F89A742C base at F89A7000, DateStamp 3b7caa6c

    and the system stops.

    Please help how to deal with this error, the tvald.sys is a Toshiba system file in the system32 directory.
    I have the Toshiba recovery cd, but I have half a month of accounting files that is not registered so I need urgently a fix where I do not format the hard drive.

    Thanks for any help
    Alex

    You are right;
    The TVALD. SYS seems to be a Toshiba ACPI-Based value added logical device driver that is required to run the stable notebook.
    It looks like these files has been has not signed with a certificate from a trusted windows source and therefore the tool of Windows XP "verifier.exe" locked or deleted. (I put t know exactly what verifier.exe)

    I put t know if you were able to solve this problem without using the Toshiba Recovery CD :(
    The TVALD. SYS seems to be stored in
    windows\ system32\ drivers\ tvald.sys c:\

    and in the registry here:
    HKEY_LOCAL_MACHINE-SYSTEM-CurrentControlSet-Services-TVALD

    However, in my opinion the verifier.exe tool should be removed and the settings must be reset!
    In this case, you can use the XP System Restore tool!
    That's all I can suggest

  • Blue screen... STOP: 0x0000008E (0xC0000005, 0xBF8B6C11, 0xA9538368, 0x00000000) win32k.sys - address BF8B6C11 base address BF800000 DateStamp 4C7d06ce

    I have a Dimension 3000 bought in 2005, upgraded to 2 GB of RAM.

    I recently implemented almost from scratch, because Opera program and profile would be repeatedly corrupted, making me lose the email. (This reappeared even after reinstall opera clean, do not use old messages or other profile files). Therefore, I restored a backup of the C: partition Ghost (there are others for my data and downloads) I did shortly after the purchase, after which I had installed only Ghost and two games (I uninstalled the games). I installed SP3 and ran Microsoft Update. I was trying to reinstall other programs that I use now. It's Rhapsody; one of my kids 'synchronize' a player MP3 Sansa Fuze with Rhapsody.

    A few days ago when closing Internet Explorer, I got a message that should be closed and I could send a report to Microsoft. It is also used to happen before, from time to time.

    Then, more recently, when I closed Rhapsody, I got a blue screen with a message that there was a problem. He said I could try to change some settings in the BIOS. I remember what happens before I restored the ghost of 2005 BU. I looked in the BIOS and not able to find the parameters referred to in (something like memory cache). I wish it were possible to print these messages on a blue screen. I didn't copy the entire message, but I write these references:

    STOP: 0X0000008E (0XC0000005, 0XBF8B6C11, 0XA9538368, 0X00000000)

    Win32k.sys - address BF8B6C11 base address BF800000 DateStamp 4C7d06ce

    This means almost nothing to me. I hope that someone on the forum knows what this means and can suggest what could be the problem.

    So far, I have not had more wrong with Opera, so there may be two distinct problems. OTOH, I reinstalled only Opera on 10/12/10; I can still have problems with it.

    Hello

    Here is more information on the bug 0x8E control: http://support.microsoft.com/kb/945658/

    The 0x8E KERNEL_MODE_EXCEPTION_NOT_HANDLED can be caused by a faulty service/driver, damaged hard drive or defective display card not enough space, or memory, Hardware/software incompatibility and third-party remote control software. So to get started:

    1. test your memory. Run Memtest you can download from http://www.memtest.org/#downiso. Download the ZIP file, extract the ISO and write on CD. Once written to CD, boot your PC with the CD and run Memtest. Allow the test to run by at least 3 passes or until it gives errors. If you have more than 1 memory module, run the test on each module separately. Try running Memtest from a cold - start unplug your PC for an hour to cool down, then immediately run memtest again when you next turn on the. This way memtest will run when the memory is cool and after the 3rd pass when the memory is hottest.

    2. update your display driver. Reference Dell seems to have highlighted 3 different models of Dimension 3000 and so there is 3 different Intel display drivers. See if you can find an updated driver on the Intel Web site. If you use a graphics add-on card try to find an updated driver from the manufacturer's website. If you have any trouble finding a driver let us know what brand and model of graphics card you have.

    3. update the Rhapsody software. (I think it's the software you using http://www.rhapsody.com/-software ?). If it's Rhapsody software I think it seems to integrate into your Web browser and it's perhaps why Opera and now IE are mistakes? You can uninstall Rhapsody for a while just to see if it is the reason for your BSOD.

    4. when the 0x8E BSOD is caused by win32k.sys, yours, is it then possible, it is caused by control software remote third. It can include programs such as VNC, PCAnywhere, etc. of Teamviewer, RAdmin.  If you use one of these programs, uninstall it and see if the PC stops mistakes.

    5 run a scan on your hard drive. You can check your hard disk for errors by going toStart ->Run -> type chkdsk c: /r -> clickOk . When asked if you want to force a sayNodisassembly. When asked to plan the audit at the next startup, Yes. Reboot your PC to allow running chkdsk.

    Alternatively, you can run a diagnostic on your hard drive. This by downloading the diagnostic program from your hard disk manufacturer. A list of manufacturers and their diagnostic tools can be found here: http://www.tacktech.com/display.cfm?ttid=287. Once more, download the ZIP file, extract the ISO and write to CD. A time written on CD, boot your PC with the CD and run the test Advanced/extended.

    Also make sure you have enough hard disk space. It is always recommended, if possible, to have at least 15% of your free hard disk capacity.

    6. Finally, take a look in your event viewer when the BSOD for possible errors. You want to look especially in the system and Application logs (and maybe Internet Explorer connects). You can run Event Viewer by going toStart ->Run -> type eventvwr.msc -> pressOk -> event viewer screen opens. If there are errors listed in one of the newspapers type them in your next post if you are not right.

    Reading your post I see 3 specific issues, that you might want to focus:

    -The memory you added (run Memtest) and hard drive (run Chkdsk)

    -The Rhapsody program - try to update or uninstall.

    -The software was initially corrupted until you make the first image after the purchase. So you just ghost the problem on.

    I hope this helps. Good luck.

  • I get the blue screen error - error - Stop 0X0000008E

    -Stop error 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000)

    Hi I get the blue screen error - error - Stop 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000) and cannot use the pc in safe mode. I have XP - OS. I really don't want to reformat the HARD drive and you want to avoid reinstalling as much as possible

    Hi aromaveda,

    ·         Have you made changes on the computer?

    Follow these methods.

    Method 1: Follow the steps in the article.

    You receive a random "0x0000008E" error message on a blue screen in Windows XP

    http://support.Microsoft.com/kb/827663

    Method 2: Follow these steps:

    Step 1: Start the computer in safe mode and check if the problem persists.

    A description of the options to start in Windows XP Mode

    http://support.Microsoft.com/kb/315222

    Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    (a) click Start, run.

    (b) type msconfigand click OK.

    (c) the System Configuration Utility dialog box appears.

    (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

    (e) when you are prompted, click on restart to restart the computer.

    Method 3: Follow the steps in the article to check the drive for errors.

    How to perform disk error checking in Windows XP

    http://support.Microsoft.com/kb/315265

    Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

  • Blue screen of death after the update installed at startup upward.

    I have windows xp sp3 after installed updates don't know which ones, because the installed when I stop and 52 of them there I now get a blue screen of death which says:

    Stop: c000007b {bad image}

    The application or DLL? \c:\windows\system32\winsrv.dll is not a valid windows image. Please check this against your installation diskette.

    I can't go to the safe mode get the same error and same with the last known good configuration. I can't even to safe mode command prompt, system, or debug mode recovery still giving me the same error. I repaired windows 3 times already and the same thing happens each time after that some update that I don't know he messes all this. Give me advice. I have antivirus Iola system mechanic. I think just to wipe the entire disk and do a clean install if you do not have anything else to tell me I'll do it, but I don't know if that even the problem will be solved because there seems to be a problem of windows software update. I also notice from the internet explorer 7 installed it stops working a few flashes upwards on you whenever you try to open it up if it's maybe part of the problem too. I do not plan to let internet 7 install go into all this time.

    Install the updates one at a time or 5 at the time may not be a bad idea.  Then when it breaks watch you and see if one of those is eager to replace your winsrv.dll file.

    You said you DO or DO NOT have to System Mechanic configured to run at startup?  Sometimes after installation of the updates, who see the new files (and if they are obsolete), can interpret the new legitimate files to be a threat.  If you could get started and uninstall that (at least temporarily) that would eliminate this possibility of this equation of many variables.

    The Dell has a number of service tag sticker and if so what does it say?  You can search for things by service number

    You should make a bootable CD of XP (no XP media required) Recovery Console.

    You see, Microsoft support engineers won't tell you how to do this either - since there is not an article of KB Microsoft Bing and link to.

    If you have a SATA drive, which will give you another challenge because you need to maybe get into BIOS and temporarily change the disk other than SATA configuration mode so the Recovery Console will be able to see, replace the suspicious winsrv.dll file, change the SATA drive and reboot...

    First, do the XP Recovery CD of Console and if you are able to use a system of work to ensure that the CD you made at least boots (you don't have to "do" something with it), which would be a good thing.

    Here's how:

    If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

    This is not the same as recovery disks that might have come with the acquisition of the system store.

    You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

    The ISO bootable image file you need to download is called:

    xp_rec_con. ISO

    Download the ISO from here:

    http://www.mediafire.com/?ueyyzfymmig

    Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

    http://www.ImgBurn.com/

    When you install ImgBurn, DO NOT install the Ask toolbar.

    Here are some instructions for ImgBurn:

    http://Forum.ImgBurn.com/index.php?showtopic=61

    It would be a good idea to test your bootable CD on a computer running.

    You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

    When you start on the CD, follow the instructions:

    Press any key to boot from CD...

    Installing Windows... going to pronounce.

    Press 'R' to enter the Recovery Console.

    Select the installation that you want to access (usually 1: C:\WINDOWS)

    You may be asked to enter the password (usually empty).

    You should be in the folder C:\WINDOWS.  It's the same as the

    C:\Windows folder that you see in Solution Explorer.

    The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

    For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

    http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  • blue screen error 0x0000008E (0XC0000005, 0x00000000, 0XF84C9CAD, 0XF80787E4) & setupdd. .sys - address F84C9CAD base at F849D000, Datestamp 48025277 whatever that means?

    I was in the middle of the restoration of the system using the power of the battery only, and the battery is dead. now, he does not recognize me.and he says that he cannot access my hard drive.

    Hello

    1. What is the brand and model of the laptop?

    You can check this link:

    You receive a random "0x0000008E" error message on a blue screen in Windows XP

    http://support.Microsoft.com/kb/827663

    For the battery issue, you can contact your manufacturer.

  • Blue screen Stop error dead: 0x0000008E...

    I get the blue screen of death at random, with the error: stop: 0x0000008E, followed by a group of numbers, followed by: base win32.sys - address BF9552CA base at BF800000, Datestamp 4DE797D3... How can I fix it, and what is it?

    Thank you
    Hi Kingfisher13,
     
    -Did you of recent changes made to your computer before this problem?
     
    Follow the steps listed in this article to resolve the problem:
  • I got the blue screen with STOP error: 0x0000008E (0xC0000005, 0xB9E28ABA, 0xAA319AE4, 0x00000000).

    Well that slowed down, repeatedly gets "blue screen" with code above.  Next line is:

    fltMgr.sys - address B9E28ABA base at B9E23000, DateStamp 480251da.

    Updating drivers did not help.  This t do?

    Need help

    Hi IsaiaAvraham,
     
    Here is an article that could be useful for:
  • When you try to Watch youtube videos, get the blue screen error: 0x0000008E (0xE0000001, 0BA460925, 0xA8919820, 0x00000000)

    I can't view videos such as youtube without my computer locking with a blue screen and error message: 0x0000008E (0xE0000001, 0BA460925, 0xA8919820, 0x00000000) how correct this and what it means? I am running windows XP. Thank you

    Hello

    · You receive this error message only when you watch videos online?

    · Do you remember any changes made on the computer before the show?

    · What is the number and the model of the computer?

    · What is the service pack installed?

    Check the status of the card/video display adapter installed on your computer.

    a. click on start

    b. click Run, in the Run dialog box type devmgmt.msc

    (c) in the Device Manager window, look for the screen reader and expand the drive, double-click the sub element to check if an error message or error code is listed.

    You can also check out the link below: general troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E": http://support.microsoft.com/kb/945658

  • Blue Screen iastor.sys, STOP; 0x0000008E (0xC0000005, 0x828490B8, 0xB96DA758, 0x00000000)

    iastor.sys - address 828490B 8 physical memory base to @8280B 000, Date Stamp 48054343 - Crash Dump, dump - the disk of 100 I can work only in Mode without failure, but I can't print or scan that I need to do. Someone can help me.

    Hello

    Looks like you need to update iastor.sys:

    iastor.sys = Intel Matrix Storage Manager driver - see System/card mother Maker and manufacturer of chipset.
    This driver could perhaps was pushed to the fault by other programs such as Symantec/Norton.

    This driver is extremely difficult to install if you need system or the manufacturer of the motherboard (for custom
    bed systems) help but you could also ask on their forums (if any).

    Also check the Intel downloads audit AFTER with the system/motherboard manufacturer...

    Intel downloads
    http://Downloadcenter.Intel.com/

    Intel Matrix Storage Manager - do not forget to check DATE and set for the version of Windows and chipset
    http://Downloadcenter.Intel.com/SearchResult.aspx?lang=eng&keyword=%22matrix+Storage+Manager%22

    More help on installing iastor.sys here (System Maker/card mother Maker first consult and use that as a last resort).

    http://social.technet.Microsoft.com/forums/en-us/itprovistadeployment/thread/98f123d4-9190-4169-A376-7a0caf0ffb2a/

    ============================================================

    More troubleshooting if necessary:

    Pick up the pieces after a computer crash
    http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crash

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
    for the office or in the Documents folder and download them from there.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive to upload collected files
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    --------------------------------------------------------------------------------------------------------------

    Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
    Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
    other pilots to check there. Disable the installation of self as those who are older and if
    Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

    See methods of update driver generic in the next message.

    BCCode: 8th 0x0000008E is the same as 0x1000008E

    Cause

    Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

    Common exception codes are:

    • 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.

    • 0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.

    • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

    Solve the problem

    If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

    • Make sure you have enough disk space.
    • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
    • Try changing video cards.
    • Check with your hardware vendor for updates to the BIOS.
    • Disable the BIOS memory options such as implementing caching or shading.

    If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

    If you do not know the specific cause of the exception, consider the following:

    • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
    • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

    If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

    If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

    Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

    The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

    You can solve the problems of BIOS by upgrading the version of the system BIOS

    BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
    * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

    =============================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.

    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Also this, so you can see the probable bluescreens. (If necessary)

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    It comes to my convenience store generic bluescreen:

    Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
    This would help. Such as ITC and 4 others entered at the bottom left. And another error
    information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do without if needed fail or the Vista DVD or recovery command prompt mode
    Options if your system was installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
    RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker
    (SFC.exe) program generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • Blue screen error: 0x0000008E (0xc0000006, 0x00000000, 0x8053B736, 0x8CDCEFE0) CI.dll HELP

    Hello I get a blue error screen... 3 days ago, my computer just beeps and restarted and blue screen... Safe mode does not work.

    The error is:

    0x0000008E (0xc0000006, 0x00000000, 0x8053B736, 0x8CDCEFE0)
    CI.dll

    I am at a loss on what to do to solve this problem, can someone help me? I use Windows Vista on your desktop... Computer is 5 years old and this is the first time for the same problem, did NOT install something again (hardware or software). Problem came out of the blue.

    I hope someone can help me

    Hi GeorgeKnight1,

    Try the methods below and see if it helps.

    Method 1

    Disconnect all external devices (printers, scanner, USB (universal serial bus) drives, etc.) except the keyboard and mouse and then start.

    If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue. Then download software updated driver for the device.

    Method 2

    Try to start in last good known Configuration and see if you can start very well.

    Using the last good known Configuration

    http://Windows.Microsoft.com/is-is/Windows-Vista/using-last-known-good-configuration

    Method 3

    If the problem persists, I suggest you perform a startup repair and check if it makes a difference.

    Startup Repair: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

    What are the system recovery options in Windows 7?

    http://Windows.Microsoft.com/en-in/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

    In addition, you can do a System Restore the Windows Recovery Console.

    It will be useful.

  • I get a blue screen with STOP error: 0x0000008e

    Original title: blue screen error

    I have the blue screen error 0x0000008e (0xc0000005, 0x81e781a7, 0x8c92791c, 0x00000000) on windows vista and I can only boot into safe mode. I don't have the copy of vista because the computer came with it installed. I just ran recienly defender of windows on it offline and that's when it started.

    Hello

    I would suggest trying the following methods and check if it helps.
    Method 1:
    Start in safe mode and put the computer in a clean boot state, and then start in normal mode and check if the problem persists.
    How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
    http://support.Microsoft.com/kb/929135
    Note: Once you have completed troubleshooting, try the procedure described in step 7 to reset the computer to start as usual.

    Method 2:
    Start in safe mode and then restore the system if it took place recently and check if it helps.
    System Restore: http://windows.microsoft.com/en-US/windows-vista/products/features/system-restore
    Warning: once you are restoring the system to safe mode you will not be able to undo the system restore.


    Hope the information is useful.
  • Error blue screen: STOP: 0x0000008E KERNEL_MODE_EXCEPTION_NOT_HANDLED

    original title: blue screen with the error: "STOP: 0x0000008E (0xC000001D, 0 x 82850572, 0x9E204038, 0x00000000)"»

    Hello everyone,

    It has been more than a week I tried to re - install my computer: ACER9802AWKMi after several months of support with blue screen apearing errors whenever there is more than one program open :-(
    So I started with a recovery disk, but the problem was still there.  The computer came with XP Home Edition and I got an upgrade to Vista (all original stuff) with all updates (SP1 and 2 and everything else updates)
    Now, every time I go on the internet: especially no problem, but if I want to play a game (online) full screen, after a few minutes:
    Yes: blue screen with messages such as
    STOP: 0X0000008E (0XC000001D, 0 X 82850572, 0X9E204038, 0X00000000)
    STOP: 0x0000007F (0x00000008, 0x8013F000, 0 x 00000000, 0 x 00000000) or
    PFN_LIST_CORRUPT or
    something with the memory of the BIOS (which I have to remove cache or mirror) witch I tried to do, but not found in the BIOS SetUp (when start PC press F2)

    Whenever I get another message :-(

    I tried with FixIt, fact CHKDSK - CHKDSK F + CHKDSK F R
    I have also run Everest to have all the necessary stuff... so if you need it...

    If anyone has a sollution, I would be very happy to hear it.

    TX much

    In the mean time brands more than 13,000,000 errors:(et toujours obtient plus élevé.)  Of course I'm not every minute in front of my screen (sometimes I work too: the job from 9 to 5, you know)

    Hi Sabine,.

    This means that the RAM is broken or damaged. If you receive error messages, you can stop the execution of memtest86 +.

    Ask someone who knew a little technical to open the laptop and check out how many RAM modules there. If it has a single module, buy a new RAM module.

    If she has more modules, remove other modules, so that you don't have 1 module of RAM left. Now run the test for each RAM module again (only install 1 module at the same time) to check if all are damaged or 1.

    If you have discovered how many RAM modules is broken, buy new RAM

    André

    "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

  • Blue screen and error code: 0x0000008E (0xC0000005, 0x8243BA8D, 0xE3452BB4, 0x00000000) _

    I get the above error message and bluescreen when the computer is just sitting idle does nothing.  Usually, it's when the internet is open, but not surf.  Can someone help me understand this.  The graphics card is an Intel 82945 G express shipset family and I checked to see if it is up-to-date and the pilot said he is up to date.

    Any help?

    Hello

    Have you checked Site system manufacturer (manufacturer of custom systems motherboard), then
    Intel downloads?

    After checking the system manufacturer's Site

    Intel - Downloads - graphical value and then the other parameters as needed.
    http://Downloadcenter.Intel.com/

    ===========================================================

    Check this thread for more information using BlueScreenView, MyEventViewer and other methods
    to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

    http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

    We can analyze the minidumps if make you it available to the SkyDrive or another file
    sharing sites.

    ZIP or download the content of the C:\Windows\minidump

    Use SkyDrive to upload collected files
    http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

    --------------------------------------------------------------------------------------------------------------

    Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
    Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
    other pilots to check there. Disable the installation of self as those who are older and if
    Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.

    See methods of update driver generic in the next message.

    BCCode: 8th 0x0000008E is the same as 0x1000008E

    Cause

    Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

    Common exception codes are:

    • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

    Solve the problem

    If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

    • Make sure you have enough disk space.
    • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
    • Try changing video cards.
    • Check with your hardware vendor for updates to the BIOS.
    • Disable the BIOS memory options such as implementing caching or shading.

    If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

    If you do not know the specific cause of the exception, consider the following:

    • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
    • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

    If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

    If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

    Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

    The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

    You can solve the problems of BIOS by upgrading the version of the system BIOS

    BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
    * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

    =============================================

    Look in the Event Viewer to see if something is reported on those.
    http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

    MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
    TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.

    http://www.NirSoft.NET/utils/my_event_viewer.html

    -------------------------------------------------------------------------

    Also this, so you can see the probable bluescreens. (If necessary)

    Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
    http://www.winvistatips.com/disable-automatic-restart-T84.html

    -------------------------------------------------------------------------

    It comes to my convenience store generic bluescreen:

    Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
    This would help. Such as ITC and 4 others entered at the bottom left. And another error
    information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

    As examples:

    BCCode: 116
    BCP1: 87BC9510
    BCP2: 8C013D80
    BCP3: 00000000
    BCP4: 00000002

    or in this format:

    Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
    Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

    It is an excellent tool for displaying the blue screen error information

    BlueScreenView scans all your minidump files created during 'blue screen of death '.
    hangs and displays information about all accidents of a table - free
    http://www.NirSoft.NET/utils/blue_screen_view.html

    BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
    There are other causes.

    You can do without if needed fail or the Vista DVD or recovery command prompt mode
    Options if your system was installed by the manufacturer.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    You can try a system restore to a point before the problem started when one exists.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    -------------------------------------------------------------------------

    Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
    RUN AS ADMIN

    Enter this at the command prompt - sfc/scannow

    How to analyze the log file entries that the Microsoft Windows Resource Checker
    (SFC.exe) program generates in Windows Vista cbs.log
    http://support.Microsoft.com/kb/928228

    The log can give you the answer if there is a corrupted driver. (Says not all possible
    driver problems).

    Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

    How to run the check disk at startup in Vista
    http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

    -------------------------------------------------------------------------

    Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
    keyboard and mouse, as well as of other major device drivers.

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    How to install a device driver in Vista Device Manager
    http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    -------------------------------------------------------------------------

    How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
    quit unexpectedly
    http://support.Microsoft.com/kb/958233

    Troubleshooting, STOP error blue screen Vista
    http://www.chicagotech.NET/Vista/vistabluescreen.htm

    Understanding and decoding BSOD (blue screen of death) Messages
    http://www.Taranfx.com/blog/?p=692

    Windows - troubleshooting blue screen errors
    http://KB.wisc.edu/page.php?id=7033

    -------------------------------------------------------------------------

    In some cases, it may be necessary.

    The Options or Vista recovery disk Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Blue screen with message 0X0000008e...:)

    Almost all the time my Virus Scanner (G Data Internetsecurity of 2010) DOE a regular analysis the computer falls down after about 20%. The deadly blue screen comes with the technical info:

    0x0000008E (0xc0000005, 0x8c0e2d25, 0xe4467a8c, 0x00000000

    Syscorr 32vsys

    Address: 8c0e2d25 basic to

    8c0d7000, Datesetup

    48728c1b

    (some letters have been Capitalletters, but I don't know which ones.) Sorry)

    Toulouse you!

    (G Data says it's not their fault...)

    Hello

    Carefully check for malware before you change your antivirus and use the withdrawal of the constructor
    tools and instructions to be sure leftovers are not left which can cause strange problems.

    List of tools to clean/uninstall anti-malware programs
    http://social.answers.Microsoft.com/forums/en-us/msestart/thread/407bf6da-C05D-4546-8788-0aa4c25a1f91/

    ------------------------------------------------------------

    Here's what I use and recommend: (these are all free and very effective versions.)

    Avast and Prevx proved extremely reliable and compatible with all I have
    launched on them. Microsoft Security Essentials and Prevx have also proven to be very
    reliable and compatible. Use MSE or Avast and Prevx, Prevx 3 but not all.

    Avast Home free - stop any shields is not necessary except leaving Standard, Web, and
    Operation of the network.

    Prevx - Home - free

    Windows Firewall

    Windows Defender (is not necessary if you use MSE)

    Protected IE - mode

    IE 8 - SmartScreen filter WE (IE 7 phishing filter)

    I also IE always start with asset if filter InPrivate IE 8.
    (It may temporarily turn off with the little icon to the left of the + bottom
    right of IE)

    Two versions of Avast are available 5.x and 4.8 x

    Avast - home - free - 5.x stop shields you do not use (except files, Web, network, &)
    Shields of behavior) - double click on the icon in the Notification area - real time Orange - click on the
    Shield that you want to stop - STOP. To stop the Orange icon to show an error indicator-
    Click on the Orange icon - top right - settings - click on the status bar - uncheck shields you
    disabled - click OK
    http://www.avast.com/free-antivirus-download

    Avast 4.8 x - home - free - stop shields, you don't need except leaving Standard, Web,.
    and the network running. (Double-click the blue icon - look OK. - upper left - Shields details
    Finish those you don't use).
    http://www.avast.com/free-antivirus-download#TAB4

    Or use Microsoft Security Essentials - free
    http://www.Microsoft.com/Security_Essentials/

    Prevx works well alongside MSE or Avast

    Prevx - home - free small, fast, exceptional protection CLOUD, working with other security
    programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here
    or use Google to see how to remove.
    http://www.prevx.com/   <-->
    http://info.prevx.com/downloadcsi.asp  <-->

    PCmag - Prevx - Editor's choice
    http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

    Also get Malwarebytes - free - use as scanner only. If you ever think malware and that
    would be unusual with Avast and occasional Prevx running with the exception of a low level cookie
    (not much), to UPDATE and then run it as a scanner. I have a lot of scanners and they
    never find anything of note that I started to use this configuration.

    http://www.Malwarebytes.org/

    I hope this helps.

    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

Maybe you are looking for