1022n printer works fine with XP, not with Windows 7
Network printer and is "seen" by XP machines. I have a laptop running Windows 7 and it can't see the camera... so I can't install it. (Of course, I can install it as a USB device... but this isn't what I want). I downloaded and installed the new Windows 7 installation software.
Any suggestions?
Disabled earlier, I had my firewall (or at least I thought so) does not.
However, I tried something someone else has suggested:
I assigned a static IP address to my printer... an address outside of my my dynamic range. Then I was able to select the option to add a printer using a TCP/IP address. It worked... so I stopped any investigation further.
It was quite a scavenger hunt determine how to configure IP address static... but someone in another thread set me off: I started typing addresses in my dynamic range until I found one that matched my printer (the goodness it's only 5 numbers since the beginning of the dynamic range) and he had the option... my ability to change an automatic IP address a manual IP address.
Thanks for your help though.
Tags: HP Printers
Similar Questions
-
How to return to the earlier version of El Capitan (from 10.11.3 at 10.11.1) with Time Machine? My HP LaserJet M475dw MFP printer worked fine with previous versions, but fails miserably to recognize the device on the same Wi - fi network now with 10.11.3. I would like to restore the previous version of the operating system without losing any data created in various applications since the 10.11.1. Fortunately, I had only to use Time Machine is rare over the years, I do not know if you have to return the entire drive to the chosen date or it can somehow just go back to a previous state of OS. Any suggestions, much appreciated.
-
My printer was working fine with Windows 7 Home Edition, then it stopped, magenta and yellow print. Ink tanks are full. What bad past and how to fix it?
If you are sure that the ink cartridges are full, then try to re-seats and cleaning the heads - http://kbsupport.cusa.canon.com/system/selfservice.controller?CONFIGURATION=1011&PARTITION_ID=1&secureFlag=false&TIMEZONE_OFFSET=&CMD=VIEW_ARTICLE&ARTICLE_ID=8783
If all goes well. -
OKI Microline 184 Turbo printer works only with Windows 2008R2
For Windows 2008R2, the test page is printed with the missing lines and introduces some corrupt characters. Only 75% of content printed ok. The printer works fine with other pilots and BONES.
Hi mikechange,The question you posted corresponds to the Windows Server forums and would be better suited in the Technet forums. Please visit the link below to find a community that will provide the support you want.Hope this information helps. -
I think it may have started when I updated FireFox. Brother multifunction printer works fine on everything but printing from the internet. I downloaded the latest printer driver, but now it prints anything on the internet. Is there a compatibility problem, and what can I do to solve it?
See this:
http://KB.mozillazine.org/Problems_printing_web_pages -
Canon pixma ip4000 printer works only with Windows 8.1
Separated from this thread.
Hai, I have a Canon pixma ip4000 printer, it works fine with my desktop running windows 7, but it didn't with my laptop running windows 8.1
I can't find any driver support to the Canon Web site.
Is there any solution for this?
Looking forward to hearing from you soon.
Thank you
Hello Chit,
Thanks for posting your query on the Microsoft Community.
I suggest trying to download the latest Windows 7 drivers from Canon Web site and then try to install in compatibility mode.
Step 1: Download the drivers from the Canon Web site.
Step 2: Installing the driver in compatibility mode.
http://Windows.Microsoft.com/en-us/Windows-8/older-programs-compatible-version-Windows
You can also provide the following link to check the compatibility of the printer.
http://www.Microsoft.com/en-us/Windows/compatibility/CompatCenter/home
Follow the Microsoft articles as reference and check if that helps.
http://Windows.Microsoft.com/en-us/Windows-8/install-a-printer
h ttp://windows.microsoft.com/en-US/windows-8/find-and-install-printer-drivers.
It will be useful.
-
HP cp1700 printer works only with Windows 8
My HP cp1700 printer no longer works with Windows 8, but worked well with Windows 7. It is visible in printers and faxes, but displays always 'offline '. This utility is not correct the problem and I could not find any solution working on the forum. HP support reminds me of Windows drivers, which are installed. I uninstalled and reinstalled the printer with hard boots but I have always the same question. Any ideas?
Problem solved with the driver HP CP1700 for Windows 8
1 module printer via a usb cable to your pc
2 turn on your printer and let windows to install the printer
3. go to control panel of configuration, devices and printers, and locate the hp cp1700
4. right click, properties, hardware, again, then click on to the left of the change settings tab
5. on the driver tab, click roll-back of driver which previous version of 2012 at the 2006 pilot
6 follow steps 3 and click on put updated driver and click search automatically and the winows 8 will find for the driver you on the internet and you will have all the features that have been installed for your printer in the end.
Hope you enjoy this :)))
-
Whenever I try to print a page open in firefox it will not print. The paper feeds through the computer, but don't not pring.
See this:
http://KB.mozillazine.org/Problems_printing_web_pages -
I can't print from the Internet, but my printer works fine with Internet Explorer
When I try to print I am asked to save the file and get "unknown error." I can print with that printer from Internet Explorer. I uninstalled and reinstalled Firefox.
See this:
http://KB.mozillazine.org/Problems_printing_web_pages -
Printer works only with Windows 10
Having improved my laptop to Windows 7 to 10 my HP Deskjet F4180 now does not work. I updated the software from the HP Web site although the scanner still works.
Chris,
Your printer appears as supported for Windows 10 using the full feature software.
Your printer:
Range of all-in-one printers, HP Deskjet F4180
Your complete software features:
DJ_AIO_NonNet_Full_Win_WW_140_404 - 4.exe
You may need to do the following:
- Download the full features software
- Remove your computer's existing printing software
- Reboot / restart and log in
- Install the full features software
- Reboot / restart and log in
Instructions, help and examples:
Install the full features software - printer
- The Windows 10 printer Frenzy section
When you see a post that will help you,
Who inspires you, gives a cool idea,
Or you learn something new.
Click the 'Thumbs Up' on this post.
My answer-click accept as Solution to help others find answers.
-
Brother laser printer worked fine, now does not print. ????
The strange thing is that it printed fine a few days ago. I don't think that I've changed something such as the registry or Services.msc and the print spooler has started in the Services. I try to print a test page and it comes is in the queue and said "error - printing". Its connected by USB and the port's LPT-1. When I use the convenience store brother tells me "a print job in the print queue prevents other printing of print." It says it has fixed the problem (a green check mark is there). When I cancel this job (only here - the test page) the same thing happens again. I don't find in Device Manager. It is not a section for printers. Would be - as Ports or USB controllers? If this is the case, it does not say "printer." Perhaps, it refers only to the port used?The strange thing is that it printed fine a few days ago. I don't think that I've changed something such as the registry or Services.msc and the print spooler has started in the Services. I try to print a test page and it comes is in the queue and said "error - printing". Its connected by USB and the port's LPT-1. When I use the convenience store brother tells me "a print job in the print queue prevents other printing of print." It says it has fixed the problem (a green check mark is there). When I cancel this job (only here - the test page) the same thing happens again. I don't find in Device Manager. It is not a section for printers. Would be - as Ports or USB controllers? If this is the case, it does not say "printer." Perhaps, it refers only to the port used?The strange thing is that it printed fine a few days ago. I don't think that I've changed something such as the registry or Services.msc and the print spooler has started in the Services. I try to print a test page and it comes is in the queue and said "error - printing". Its connected by USB and the port's LPT-1. When I use the convenience store brother tells me "a print job in the print queue prevents other printing of print." It says it has fixed the problem (a green check mark is there). When I cancel this job (only here - the test page) the same thing happens again. I don't find in Device Manager. It is not a section for printers. Would be - as Ports or USB controllers? If this is the case, it does not say "printer." Perhaps, it refers only to the port used?The strange thing is that it printed fine a few days ago. I don't think that I've changed something such as the registry or Services.msc and the print spooler has started in the Services. I try to print a test page and it comes is in the queue and said "error - printing". Its connected by USB and the port's LPT-1. When I use the convenience store brother tells me "a print job in the print queue prevents other printing of print." It says it has fixed the problem (a green check mark is there). When I cancel this job (only here - the test page) the same thing happens again. I don't find in Device Manager. It is not a section for printers. Would be - as Ports or USB controllers? If this is the case, it does not say "printer." Perhaps, it refers only to the port used?
I didn't think that it would make a difference because she seems to be a problem of connection/port. Turns out it was a hardware problem... a cable failed. It was a removable end. Never seen that before. Probably not a good feature! In any case, it was a good lesson. I should have replaced the first thing cable rather than a lot later. Its fast and results are instantaneous. Everyone seems to have extra cables lying around!
-
DeskJet F4180: F4180 driver works only with Windows 10
Printer prints all bad, except the dark colors. Turns red magenta, green is dark blue etc.
Printer worked fine with win xp.
Test page prints perfectly without error
Using the prints to photocopy an exact color copy - it's just data coming directly from the computer which is incorrect, so the work of does'nt driver properly with win 10. I checked that I have the latest version of the driver 6.1.7600.16385.
I have noted this problem has already been spotted upward - when a new driver is available?
or can anyone suggest a work around.
Printer I tried with my laptop win10 and the fault has been the same.
Printer I tried with my old desktop winxp and the rift was healed - perfect impression of a jpeg file.
Reconnected printer back on my desk win10 and printed on the same jpeg file and printing was perfect!
Have you tried a few other files that I had problems with and prints are very well - can only be assumed that the problem was down to the usb connector.
Thanks for the help
Concerning
-
SENTINEL HASP KEYS 3.25 WORKS ONLY WITH WINDOWS 7
I lived several of these posts here about the hasp and windows keys 7 and I tried many suggested fixes, but nothing works. I installed the software using Windows XP Mode in Virtual PC, I've updated, uninstalled drivers, reinstalled with and without the hasp key inserted. I use the Sigmanest V4, Mastercam9, and Mastercam10 software. All three of these programs worked fine with Windows XP service Pack 3. I did everything that I mentioned above and some of which you try to run the software in compatibility mode. Nothing I try works, Sigmanest software seems like it is recognizing the hasp key because it will be open, but it will not open in demo mode. The two programs Mastercam do not even recognize the hasp key. They open up and say that there is no present hasp key, then close. After years that Windows 7 has been out someone got a solution for this. Maybe they have, but I can't?
Hello Chad,
Thanks for posting your query on Microsoft Community forum.
According to the description of your problem, it seems that you are trying to install the drivers for the Sentinel 3.25 HASP key. I checked the official site, it shows drivers for Windows, but did not mention the version of Windows.
Here is the link: http://sentinelcustomer.safenet-inc.com/sentineldownloads/?s=&c=End+User&p=HASP+HL&o=Windows&t=Runtime+%26+Device+Driver&l=all#.
I also checked this device and software Center of Microsoft Compatibility, and I couldn't find any information out there in that regard. So I suggest you to contact technical support SENITEL for troubleshooting further because they are the best people who can say that this device is compatible with Windows 7 or not.
Hope this information is useful. Do get back to us after contacting them and please update your question on the forum.
Thank you.
-
I just got a new modem (Arris SB6190) and now my Airport Extreme does not connect. It worked fine with the previous modem (a rented one TWC). Help!
Always recommended to reset the airport back to settings by default and then set up again whenever you have a new modem or change your Internet Service provider.
Turn off the new modem for at least 30 minutes. More is better.
Perform a hard reset on the AirPort Extreme, then it turned off.
Make sure that the Ethernet cable connects the modem to the "O" on the AirPort Extreme WAN port
After the power of the modem 30 minutes down, turn on the modem and let it run for at least 5 minutes by itself.
Then, turn on the airport and let it run a few minutes
Set up AirPort Extreme again
Important note... There are many reports of problems with the modem Arris SB and airports. Both are great products, but they do seem to work perfectly together for some users.
-
I have problems with Lightroom. I just downloaded the creative cloud with LR and PS PS works fine, but does not open LR. It is stuck on the license screen and freezes. Please notify.
reset your preferences-
Acrobat: http://help.adobe.com/en_US/acrobat/X/pro/using/WS58a04a822e3e50102bd615109794195ff-7feb.w .html
Adobe media encoder: https://forums.adobe.com/thread/1713540
Legacy: http://helpx.adobe.com/after-effects/using/preferences.html
Bridge: https://helpx.adobe.com/bridge/kb/troubleshoot-errors-freezes-bridge-windows.html
Dreamweaver: https://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs6-cc.html
Flash: http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html
Illustrator: http://helpx.adobe.com/illustrator/using/setting-preferences.html
InDesign: https://forums.adobe.com/thread/526990
Lightroom: https://helpx.adobe.com/lightroom/help/setting-preferences-lightroom.html
Muse (mac): https://forums.adobe.com/thread/1246022?tstart=0
Photoshop: https://forums.adobe.com/thread/375776
Photoshop elements: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html, http://www.photokaboom.com/photography/learn/Photoshop_Elements/troubleshooting/1_delete_p references_file.htm
elements of first: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html
First pro: http://www.mediacollege.com/adobe/premiere/pro/troubleshooter/trash-preferences.html
Maybe you are looking for
-
Safari does not work after upgrade
After I installed the latest update from the App Store on my MacMini (V. OS 10.9.5), Safari (V. 9.1) does not work well as before. Most of the pages he used to open, now do not work, example Facebook.I tried to open the same pages with FireFox and Ch
-
Tecra M5: Cannot install driver nVidia on Vista Ultimate SP1 x 86
Today I installed the version of Vista Ultimate with SP1 (PTM51E - Bios 3.60) Since installing I can not any version of the nvidia drivers graphics card to install. "Driver Installation Module stopped working and was closed" is the error that happens
-
CWIMAQdx.GetAttribute failed to get attributes in the string or format U32.
I'm reading all the attributes of a Gige camera. I can get the I64, F64 attributes and Boolean marker. But when the type is string or U32, the returned object "attribute" is "NULL". Can someone let me know what is wrong with my code? Thank you object
-
Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?
-
Refresh a screen with a KeywordFilterField
How can I get the screen to refresh after deleting an entry in a KeywordFilterField? If I close the screen and then re-open it, it seems OK, but I want the screen to refresh as soon as the entry is deleted. If it were a ListField, I could call setSiz