1042 q with PXI 8360-controller and maps of Pickering

Similar Questions

• Installation of driver with PXI-8360 error "this device cannot start - Code 10"

  While trying to install PXI-6541 to the PXI-1036 chassi with controller PXI 8360 [express-8360 side laptop], the error message "this device cannot start [Code 10]" laptop is Lenovo T60 with the latest version of the BIOS

  Thank you

  Manu

  Sounds great Manu,

  I also followed on that for you, then you should be getting approval sometimes today.

  I hope for the best

• Problems with the Ethernet controller and PCI Satellite L30-10 X device driver

  HelloW!

  Sorry for my bad English, I'm from the Russia.
  A few days ago, I bought Satellite L30 - 10 X with W Vista on board. In my opinion, that this OS does ' t very good on this computer, so I install W XP.

  I have some problems with drivers. At first, I don't know which model I have: PSL30 or PSL33? I have download all the drivers for the two models. But after installation, computer doen't find the drivers for the Ethernet controller and PCI device...

  Hello

  Satellite L30-10 X belongs to the series of PSL33E. This number located on the label on the bottom of the device!

  You must choose this number in the form of driver download for XP compatible drivers.
  I put t know why you are not able to install the LAN driver. I have the same laptop with Vista and I've install the XP and all the drivers will work perfectly.

  I assume that you have installed the drivers in the wrong order. Please take look in the Toshiba installation instructions txt file. In this order, install the driver! This is important.

  I think that you should install XP again to ensure that the registry clean, then download and install the XP drivers compatible as mentioned in the installation instructions file.

  Good luck

• WebAuth LOCAL with Wireless Lan Controller and ISE

  Greetings,

  We intend to set up a centralised comments with sponsored webauth wireless network. I didn't know that this will not work with our current WLC code (6.0.199.4) as 7.2 or later version is required.

  We have a project to upgrade the WLCs but he won't be ready before the deadline for the completion of the reviews wireless.

  I am using local WebAuth temporarily until the WLCs are ready. My questions are:

  1. am I correct that I can still authenticate ISE?

  2. Since local webauth does not cost support, does that mean I can't apply a pre or post auth ACL?

  3. can someone point me to a good guide for configuring local webauth?

  Thank you!

  Hi Leroy,

  In CWA you can push the AVPs desire in the final result because of the nature of the flow:

  -Comments will connect to the SSID.

  -WLC send wireless MAB ask (1st authentication). In response, ISE returns accepted with url-redirect-acl and redirect url.

  -WLC updates the client session and once http (s) generated WLC redirects the customer to ISE according to AVPs received at the 1st auth(MAB request).

  -The customer enters the identification information in the portal. ISE valid creds and refers to WLC one type COA to re-authenticate.

  -WLC re authenticates the client (2nd authentication) session, and at this point ISE can support AVPs custom as names of VLANS, Interfaces or space air dynamic ACLs.

  -WLC overrides the client session with the new attributes.

  Local Web Auth as you mentioned, there are 2 steps but the WLC "considers" cela a single thread.

  To the LWA, the flow is as follows:

  -The client connects to the SSID.  Since there is no involved L2 auth client through DHCP, captures an IP and arrives at WebAuth_Required. Redirect URL is configured statically on WLC and pre auth ACL allows client access to ISE during the auth phase.

  -Customer opens the browser and WLC redirects the customer to ISE, but breast of redirection, there is a 'return to WLC' action which indicates to ISE to send customer WLC virtual IP containing identification information of the client used for auth in portal comments.

  -In this way the WLC now "knows" the handed creds to ISE and this way there is a formal request from RADIUS WLC sends to ISE asking these creds. ISE links in return an accept, and this is how the WLC now "knows" that auth is correct and she should move client to RUN.

  LOA of the simplest way would be to define an Interface of comments and statically applying a restrictive ACL at the level of the interface rather than wait the AVP of AAA server.

  LWA is supported in this version at very low level and basic, but if you want a complex flow involving the pusher of the dynamic attribute you will need something higher to 7.2.110.0.

  Recommended version would be 7.6.130.0 as for now.

  Kind regards

  Antonio

• Compliling VI in LabVIEW with cRIO-9004 controller and chassis cRIO-9104

  I tried to compile in LabVIEW with cRIO 9004 and cRIo-9104 connected.

  It has three options

  (1) use the server local compilation.

  (2) to connect to the network compile Server

  (3) to connect to the service of LabVIEW FPGA cloud compile

  But I'm unable to compile my program using one of these.

  How can I get my compilation made? Help, please.

  Thanks YouCp

  Service provider shared's Standard Service program is an annual fee of NOR, which in turn allow you to update your modules and LabVIEW and benefiting from the support of NEITHER.

  https://www.NI.com/services/software_benefits.htm

• Problems of allocation of resources motherboard PCI with PXI controllers

  I set up a test system to a PXI-PCIe8361 controller and a PXI-1042 chassis.  Several years ago, there are known problems with some motherboards on the assignment of the PCI resources.  I looked and could not find more old messages and lists of recommended motherboards.  It seems that ASUS is a manufacturer in order to avoid any Abit and Gigabyte function well.  Is there a list more up-to-date recommended motherboards or manufacturers?  Is it still a problem with the latest motherboards?

  Any information will be appreciated,

  Nick

  Hi Nick,

  PCI resource allocation issues are significantly less common with new mothers/BIOS maps. In situations where this problem always produces a BIOS update usually solves the problem. The best advice I can give if you buy a new computer for connection of MXI must go with a PC and a cell phone, who you are.

  These question is sufficiently rare that we do not maintain a list of manufactures suggested, if you encounter any problems you can call us at the 1-866-ASK-MYNI, and we would be happy to help you.

  Thank you

  Scott M.

• Upgrading memory on the PXI-8105 controllers and PXI-8106

  Hello

  I've recently upgraded the memory of three PXIs; one with a PXI-8105 controller and two with the PXI-8106 controllers.  Both the 8105 and 8105 can have a maximum of 4 GB (2x2gb) DDR2-677 (PC2-5300) (see links below).  However, on the three systems, both the BIOS and the o/s only see 3.3 GB.  No idea why this might be the case?

  I tried to Flash the BIOS (v1.4 on the two PXIs), but without success.

  We use COTS memory (i.e. not purchased NOR) but I would be badly pushed to believe it is the cause of the problem.

  Thank you.

  Links;

  • The PXI-8105 http://sine.ni.com/nips/cds/view/p/lang/en/nid/202630 max memory capacity
  • The PXI-8106, http://sine.ni.com/nips/cds/view/p/lang/en/nid/203442 max memory capacity
  • Update BIOS page: http://digital.ni.com/public.nsf/allkb/9C9362590B05CD6E86256B270082164A

  I don't know about the BIOS reports less than 4 GB. Here's a blog post that best describes what I wanted.

• PXI-1042 q with controller 8331

  HI........

  I want to configure a single chassis PXI-1042 q with controller PXI-8331. I have connected 2 I\O Digital Digital card (PXI-6515) and 1 card(PXI-6514) I\O to this chassis. And I have connected this chassis to my PC with the serial cable (OR standard cable on COM 1) on my PC. But the problem is when I opened and Measurment Automation explore it dose not detect chassi eithre or any card I\O.

  I installed OR version 4.6.1 platform services.

  An obsrevation is led RX ON Chassi and dose led TX ON PC does not illuminate.

  Please guide me step by step configuration.

  Thank you

  Pravin.

  PBL,

  The PXI-8331 is not a serial interface, even if the connector looks like it, so it should not be connected to COM1.  It works when it is connected to a PCI-8331 in your host PC.  The cable must be a MXI-4 cable, for example 190957-03, not a cable series.

  If that's what you do, please report the LEDs on the two cards.

  -Robert

• Options of DMA with the NI PXI for the PCI 3 rd-party with no DMA controller device

  Hello

  I need to extract data my device PCI 3 rd-party at 22 MB/s.  The fastest, that I was able to continue to use NI-VISA 5.4 in LabVIEW 2013 is 1.6 MB/s with the function move in 64.  There is no DMA controller on the 3rd party device.  I was hoping to use the DMA of the host controller and a VISA MEMACC object, but I fell on 3229I2RA knowledge base: How do NI PXI controllers support DMA (Direct Memory Access)?  The KB has that "our PXI controllers support only the PCI specification and therefore do not a DMA controller on the motherboard."  If there is no DMA controller on the PCI 3 rd-party device, is there no DMA option for my 3rd - party on NI PXI controllers device?

  Thanks for your time and your thoughts,

  Steve K

  Currently, there is no controller PCI DMA accessible by the user on computers NI PXI.

• PXI-8115 controller incompatible with the PXI-1050 chassis?

  I replaced two XP based PXI controllers with two controllers, PXI-8115 with WIN7 installed on them. System #1 has combined PXI-1010 chassis and System #2 has a combo chassis PXI-1050 chassis. The two 8115 controllers work correctly when it is installed in the #1 system (chassis 1010) do not produce but no video output when it is installed in the #2 system (chassis 1050). I use the same monitor on both systems, as well as the same adapter DisplayPort to VGA supplied with controllers. This suggests some kind of incompatibility between the 8115 and the 1050, but I can't believe I'm the first to connect a 8115 a 1050. Everyone knows about this problem? Y at - it solution or workaround? Is there something I forgot?

  Thank you

  PMAC

  OK, I found a solution but I still don't know why it is the solution.

  Each controller had a "Bizlink" adapter DisplayPort to VGA bundled with it. Of course, I tried two adapters with the same results on both systems. I tried a "Startech" DP to VGA that is used elsewhere in the installation and the system worked well. Why a brand different adapter works is quite confusing.

  For anyone else having this problem try Startech manufacturer DP2VGA.

  PMAC

• Help with PXI OR 4070 DMM and OR PXI MUX 2501

  Dear alls,

  Sorry to post a simple question, but I couldn't understand it.

  My PXI1033 chassis has NI 4070 Flexdmm and NI PXI MUX 2501, block of connection OR-TB2605, 1 thread by MAX-mode configuration.

  I'm trying to measure 3 voltages (from 2V to 5V) by connecting them to ch0, ch1, ch2 MUX2501 (Terminal screw for example 67,66,65 and common screw terminal 27).

  Any device passes self-test to the MAX.

  I then use NOR-DMM/Switch Express, swap the added devices and also scan list.

  Trigger is PXI; Handshake (PXI trigger 0 and 1 PXI trigger)

  However, I could not measure all the signals.

  I also try with other examples in LabVIEW help, but have still no results.

  Am I missing something?

  And, although the trigger section is very clearly explained, I have no idea how the DMM to run his measure through switching and multiplexing. How DMM connected MUX?

  I noticed that the DMM and the switch share the same trigger bus (two of them bus trigger 1), but their local buses are different (DMM: local bus left/right = 2, 4, and buses premises MUX left/right = 3.5)

  Your advice is much appreciated.

  Thank you.

  Van.

  Lonestar thanks!

• I'm having a problem with Windows7 Home Premium and WWII CFS joystick operation. I get a message saying that the controller has been changed. Microsoft offers a patch?

  I have problems with Windows7 Home Premium and WWII CFS joystick operation.  I get a message from gibberish, saying that the controller has been changed.  I tried to replace the file with a version of Windows XP .cfg and also tried to re-write the .cfg file.  Apparently, this version of Windows will not allow a file to be saved with an extension ".cfg", so it does not work either.  Any suggestion would be appreciated.

  Thank you

  Hi Bob,

  You can consult the following links of wire and check if it helps.

  Joystick does not work with the Europe of WWII Combat Flight Simulator series. Help?

  With the help of WW2 Europe Combat Flight Simulator series with Windows 7 Home Premium

  Note: The above links contain third party links. Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

• With the help of the network location and mapped a drive to the server FTP. during the transfer of very large amounts of the login information is always lost.

  With the help of the network location and mapped a drive to the server FTP off site; during the transfer of very large amounts of the login information is always lost.  Computer power settings are configured to not to do no matter what, I'm assuming that the ftp server can publish a scenerio timeout but is there a way for my computer and windows to restart the file transfer?

  Hello

  Thanks for posting your question in the Microsoft Community forums.

  I see from the description of the problem, you have a problem with networking on the FTP server.

  The question you posted would be better suited in the Technet Forums. I would post the query in the link below.

  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads

  Hope this information helps you. If you need additional help or information on Windows, I'll be happy to help you. We, at tender Microsoft to excellence.

• I bought a Xbox 360 for Windows gamepad, as well as a Play and Charge kit. If I want the charge with this kit controller, can I use a USB/power Apple to the charge controller plug?

  I bought a Xbox 360 for Windows gamepad, as well as a Play and Charge kit. If I want the charge with this kit controller, can I use a USB/power Apple to the charge controller plug?

  Hi Arvin,

  The question you posted would be better suited in the Xbox Forums. I would recommend posting your query in the Xbox Forums.

   

  Welcome to the Xbox support

  http://support.Xbox.com/en-us/

  Hope this information helps.

• What is the situation with the mac pro users and map of cuda for ray-tracing work?

  What is the situation with the mac pro users and map of cuda for ray-tracing work? If it is not necessary or should I try to install a?

  CUDA acceleration is no longer under development, and I've only played with traced to the RADIUS on a few test projects. If I need 3D dimensions objects I used C4D Lite, which is now included in EI