12.5.1 iTunes fails to install (new)

My Toshiba Portege running Win7 fails to install iTunes 12.5.1.  It's the same problem, I met years ago with 6464 installers, but found the installer for old video cards work perfectly.  Apparently someone at Apple decided to not (yet) offer Setup for older video cards for 12.5.1.  I spent 6 hours so far today tried a multitude of settings with installer 6464.  In the meantime I have remove all the Apple software in the prescribed sequence and restart.  I've got rights admin - so what happens?  I'm headed to 12.4.3 now so I can communicate with my new iPhone SE.

Okay - I found my own solution, but he was buried in the documents to help around to install iTunes on Windows. Apparently I can't find the version of iTunes for older video cards directly by Apple, but there was a link in the help to the 12.5.1 document version.  With the download of the iTunes64Setup (not the 6464), I was able to successfully install 12.5.1! Now, I can't wait for the next update see how much fun it will be to locate the 64 version...

Tags: iTunes

Similar Questions

  • iTunes fails to install the created PhoneGap Build .ipa file

    I used PhoneGap Build to create a .ipa file signed.   However, iTunes is not able to install it on my iPod Touch which is running iOS 9.3.4.   When I start to synchronize the device it goes through the process of installation of the application, but then the application icon disappears and no error message is displayed.   Any suggestions on how to figure out what might be wrong.   I use the latest version of PhoneGap - cli - 6.3.0 (4.2.0 / 5.2.1 / 4.4.1)   My application ID is 2214031.

    Yes.

    The distribution certificate allows you to download from the AppStore. Apps can only be downloaded and installed from there, then.

    If you want to install on your device to directly test a .ipa, there a development certificate, the devices registered (in your account of Apple developers) and a mobileprovision with these included devices.

  • Please help, failed to install new graphics card

    I have an Aurora R3.

    His current graphics card is AMD 6870. R3 of Aurora standard motherboard, PCI 2.0.

    Buy AMD R9 390 (recommended 750w). Did not work. Noticed that I had a 525 power so I bought feeding 875 w. It still does not work.

    I know that the new card is PCI 3.0, but it is backward compatible, so that can't be the issue. It may not be the power supply as I just traded it a new (standard 875 w W299G, didn't need to replace the harness, new works of supply of power with my old card as well)

    When I say does not work I mean that: the map lights. Spin Fans, but nothing appears on the screen.

    I uninstalled all the drivers completely and reinstalled etc... I tried every display port. No matter what I can not do anything to display on the screen.

    Help, please. I'm ready to get down to the Nvidia GTX 970 if that will solve the problem.

    In addition, please let me know if there is no system information I neglected to mention that would help solve the problem.

    It should work if you have 875 w power supply, and there good-PIN-cards of power in native mode.

    Since it is Aurora-R3 you better get one with a Dual-BIOS switch that supports legacy and UEFI hybrid.

    Aurora R3 is perhaps than just EFI (not true uEFI) so he cannot decide that he needs. Save yourself a lot of trouble and get one with a switch on the video card.

    Apparently, some recent MSI & Sapphire cards have the switch.

    You might have to no-snap and remove plastic card aerial of Aurora video guide if new card out in cases.

    I also have it in my notes that someone wrote:

    I just wanted to say that the 380 R9 works. But you have to buy a graphics card of the hybrid BIOS as "Sapphire R9 380 Nitro". Sapphire cards are able to pass the legacy BIOS to UEFI BIOS boot. There is a small 'switch' in the corner of the map, which you can use. It works very well without any problems.

  • just installed new update for itunes. When I go to the page stoe it flashes really hurt. anyone with this problem. is there a solution?

    just installed new update of itune. When I go to store the page, it's really bad flicker.  anyone with this problem. is there a solution?

    Widely not reported, no known resolution until Apple release a new version of iTunes that affects it.

  • Dist. Kit fails to install, a newer version already exists of reports

    I'm with CVI 8.5.1 on Windows XP sp 2.  distribution kit fails to install executable for a project, sites that have a newer version already exists.  However, previous versions did exist on either the c: drive or that they appear in the Control Panel Add / Remove programs.  Any ideas?

    Rick

    The installation program is to find indications that the release 1.0.14 of your software already exists on the system. If this is not true, then he could have some problems when uninstalling this version. If you search your registry database for the product code {7D8D2E0B-CEB1-44D0-A081-1B0C039F9157}, I'm sure you'll get some hits. If the software cannot be uninstalled from Add/Remove programs as you say, then I recommend to use the enclosed MSIBlast utility to remove the order of it. Unzip and run the program, and then check the box "Display all installers" at the top. Find your software (by name, but check the product code) in the list, and then uninstall it. Be very careful when you use this utility that you uninstall the right thing. You don't want to accidentally delete something important.

    A. Mert

    National Instruments

  • Running Adobe cs5 on my desktop and laptop. The desktop hard drive has failed. A new hard drive was installed. I reinstalled Adobe cs5, but I can't update.

    Running Adobe cs5 on my desktop and laptop. The desktop hard drive has failed. A new hard drive was installed. I reinstalled Adobe cs5, but I can't update.

    Try direct updates

    https://www.Adobe.com/downloads/updates/

  • "iTunes Sync - cannot install" - Push Notifications

    Hi, I m trying to install an adobe air 3.9 for ios in the development of applications with the Notifications.

    I have create a new APPID with 'Push Notifications' and created a certificate for this push notifications (1 for dev) and 1 for the prodution.

    I then creates ""Provisioning profile "where I choose my APPID. "

    I converted the *.cer to *.p12 with openSSL...

    I put everything in Flash, and I changed my XML to contain:

    < iPhone > < InfoAdditions >... < / InfoAdditions > < rights > <! [CDATA [aps-environment < key > < / key > < chain development > < / string >]] > < / rights > < / iPhone >

    Suite: http://www.Adobe.com/devnet/air/articles/iOS-push-notifications.html

    When I try to install the app via iTunes

    "iTunes Sync - failed to install.

    Anyine can help me? Thanks in advance!

    Gonçalo


    OK Gonçalo,

    I found the solution:

    The certificate, you must convert it to P12 and enter the ipa is not the certificate of the AFN, but one you use with the profile of proviosioning!

    Keep it...!

  • "Extraction failure: cannot open output file" error message when installing new drivers

    Hello, I am trying to install new drivers for my HP Photosmart C4385 printer.  I downloaded the complete drivers of features for Windows XP 32-bit, and when I start to install (extract), I get the error message:

    Extraction failed

    Cannot open output file

    And the process ends.  He arrived at about 85% extraction every time.

    No idea why?  I called HP, but no longer under warranty they wanted money, which I think as absolutely ridiculous - not even give me basic support?  Poor, poor customer service.

    Hi GIJeff12,

    Temporarily disable any AntiVirus/Antispyware software.

    Cut the installer on your desktop then click on the Start Menu, click computer, double-click on the C: drive and paste the installler here.  Now try a right click on the installer for your printer, choose 7-Zip and choose Extract the files, and then click Ok.  If the installation program extracts now correctly, follow these steps.  If it does not extract, let me know.

    Disconnect your printer from the PC.  Restart your PC.

    Open the newly extracted folder and double-click the setup application to start the installation (the installation application will probably have the same icon as the original installation software that you downloaded).  Connect the printer to your computer when you are asked.

    If it was a success, re - enable your security software.

    Best wishes

    DP - K

  • Update KB2446708 has repeatedly failed to install, citing 66A error code.

    Optional updates succeeded where this is important and some recommended to those who do not. Help and troubleshooting suggestions were followed, but in vain. Is there a way to delete all updates failed and regain some lost speed, not to mention allow updates installed?

    Hi Ed,

    First try the solution at this link: http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992&displaylang=en&lc=1033.

    If this does not work, remove Microsoft .net Framework 4.0 using the .NET Framework Cleanup tool http://blogs.msdn.com/b/astebner/archive/2008/08/28/8904493.aspx.  And then reinstall the Microsoft .net Framework 4.0 http://www.microsoft.com/downloads/en/details.aspx?FamilyID=0a391abd-25c1-4fc0-919f-b21f31ab88b7&displaylang=en and then install the update, you are having problems with.

    If this does not work, try resetting update (including a fixit) components: http://support.microsoft.com/kb/971058

    If this does not work, try a manual download by putting the KB numbers who fail looking here: http://www.microsoft.com/downloads/en/default.aspx and download them directly and see if it works.

    If this does not work, go to C:\Windows\SoftwareDistribution and remove content (but not the folder itself) and then restart.  See if that helps.

    Remove updates failed won't find you any lost speed - although if it could be done, it might be useful save you some space (assuming that all who uploaded was saved even if it has failed).  It also will not help install new updates.  It's a totally different question that hopefully will solve the above.  If a solution works for some but not for all of them, then try the other options to see if they can help as well in terms of everything attaches.

    If this does not help, please repost in the forum for the correct Windows version from: http://answers.microsoft.com/en-us/windows/forum/windows_update?page=1&tab=all&tm=1300700638376.

    I hope this helps.

    Good luck!

  • KB2483185 fails to install even after difficulty there 50593

    I am unable to apply the update to Microsoft KB2483185 February.   I think it started because of a failure of file download, but that has been corrected and now is stuck because MS of a workaround does not work.

    As stated on the KB article http://support.microsoft.com/kb/2483185, I ran Microsoft Fix it 50593 (and in fact have managed to activate and deactivate in trouble several times during troubleshooting) and I tried the update again with no joy.

    I contacted the support of MS, and they walked me all first through a process of liberation of the previous downloads, and then trying to apply the fix in Mode safe without using MS Update, installing got message error "Setup cannot copy the file shimgvw.dll.

    MS continues to insist the that put up-to-date may be broken, despite the fact that I run and successfully installed several other fixes of update since I first tried KB2483185.

    I think the parameters of access control for C:\WINDOWS\system32\shimgvw.dll are confused.  I should also mention that Windows Picture and Fax Viewer no longer appears in my context menu (instead it lists 'shimgvw' but choose just gets an error message.

    The original for KB2483185 web page gave an alternative manual to fix my web searches have found several different suggestions for the parameters to use with the 'Cacls.exe' command to set the access control for shimgvw and he 50593, but this info is no longer available.

    Anyone know where I can find the official news of MS on the manual alternative to fix 50593?

    Or does anyone have any general suggestions for my problem or specific settings to use for Cacls.exe to ensure shimgvw.dll has appropriate access control settings?

    Difficulty running it 50590 would have allowed to this workaround. Difficulty running it 50593 (which you already did) would have disabled (or "cancelled") workaround.

    If you would run difficulty he 50590 but have not run difficulty he 50593, KB2483185 fails to install & explain your situation:


    Note that before installing the MS11-006 security update, you must cancel this work systems where you previously applied around it.

    Source: the section you referenced in http://www.microsoft.com/technet/security/bulletin/MS11-006.mspx

    So no, something (for example, W32/Alureon-Variant or another infection) is originally failed to KB2483185. And Yes, I want to contact you the MS Support again once (be sure to quote your case of origin or SRX): this time, you will need to firmly insist on talking with technology to 'level 2 '.

    Also to give tech a link to this thread for reference.

    Note: All the foregoing assumes that you have a functional application of the antivirus installed AND that there is no "leftovers" from a previous installs a Norton or McAfee application.

  • Windows Update fails to install the update and ask again to install

    Hello

    Firstly, sorry if my English...

    I have a sony vaio laptop with win 7 Home premium 64-bit pre-installed

    so far, all updates went well, but there are 4 updates, also marked important, which fails to install.
    Windows Update try to reinstall them every time... but every time fails. Whenever I stop the laptop that I have to wait for these updates installed... knowing that the next time I'll close the laptop, the same 4 updates will be installed, without result.
    the updates are:
    KB975467 - error code 80070BC9
    KB973688 - error code 643
    KB954430 - error code 643
    Kb973923 - error code 643
    Please help me...

    Hi Luigi,

    Don't worry about wasting my time. I love doing research and constantly learn new things.  I found another post on this site which recommended the .NET solution.  Here is the link to this article: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/e3d8edeb-1a3b-42d3-a635-070264696db5.  Unfortunately the user in this link has failed to let us know if it worked for her or not.

    If this does not work (or you don't want to go through the above steps), you must contact Microsoft Update Solution Center http://support.microsoft.com/ph/6527#tab0.  Click on Contact a technical support engineerand accept the agreement.  You will receive the free e-mail directly support from Microsoft Support staff.  Don't forget to let them know all the steps you have tried so far so that they are not duplicated.

    If this is resolved, I'd be happy if you referred to this site to let me know how it was fixed.

    Good luck

    Barbara

  • recommended security cumulative ie8 and compatible display updates fail. can install it with the installer of standalone download but then ie8 does not connect. If I remiove update ie8 works very well

    recommended security cumulative ie8 and compatible display updates fail. can install it with the installer of standalone download but then ie8 does not connect. If I remiove update ie8 works very well

    Hi mikedav,

    Thank you for using the Microsoft Windows Vista Forums.

    Method 1:

    Microsoft has released a new "Fix it" solution that should automatically solve your problems with Windows Update.  Just click on the link below and follow the instructions.

    How to reset the Windows Update components?

    http://support.Microsoft.com/kb/971058

    If you are not able to connect to the internet after you install the update, you need to optimize Internet explorer by following the instructions below.

    Method 1:

    Follow the instructions in the link below which will help you solve the problem.

    Tips for solving problems with Internet Explorer

    http://windowshelp.Microsoft.com/Windows/en-us/help/8038f9ac-9bf9-4809-8d75-fc42818d8af71033.mspx

    Method 2:

    Follow the instructions in the link below to optimize Internet Explorer.

    How to optimize Internet Explorer

    http://support.Microsoft.com/kb/936213

    Please post back and let us know if it helped to solve your problem.

    Kind regards

    KarthiK TP

  • Cannot use Windows Update - KB982132 and KB972270 fail to install, error 0x800A0007

    I can't using Windows Update for two 'critical updates of security". I got anumber of error messages, but the last was 0x800A0007. This is nowhere on their support pages. Can someone suggest a possible solution?  (If I can solve this problem, I can get IE9 fixing.) With the help of Windows XP Edition family

    The two KB982132 and KB972270 updates failed to install (twice) with error message that appears now is no longer on the 0x8007001F support page.

    Since that time when I get to "check your computer for Updates" page fails to display and code error 0x800A0007, which also appears nowhere.

    Norton Internet Security Firewall is disabled and the Windows Firewall is enabled.

    Thank you-

    Do not uninstall IE8 or IE7 before doing a repair installation leaves the two Internet Explorer and Windows in a "confused" or "broken" State - so your Windows Update (if any) problems.

    I'm sorry to tell you that your only recourse now formats the hard drive & then by doing a new installation of Windows. [1]

    Follow the instructions in this post of mine in another forum (to-the-letter & in order! ) to restore your computer to a State safe & functional: http://aumha.net/viewtopic.php?f=62&t=44636

    If you need additional help with the clean install, please start your own, new topic in this forum: http://answers.microsoft.com/en-us/windows/forum/windows_xp-system

    Note: The computer must NOT be connected to the internet or local networks (i.e. other computers) in its current state. All your personal data (e.g., banking online & passwords credit card) must be considered at risk, if not already compromised.

    Wish I had better news for you.  Good luck!

    =======================================================
    [1] PS: I learned that the hard way, too, many years ago!

  • pilot has worked with xp now fails to install

    OK, so enough long story but here goes.

    im making a POS system and one of my components is a USB cash drawer.

    He has installed on the pc very well and worked very well. Now the pc could not start like system32/config/system has been corrupted.

    I finally this restored from the original after much work around.

    Now, however, whenever I have install new drivers (the mainly cash drawer) that they are unable to install it and I can't make them work.

    Why the hell would this be if windows works now? Is there a hardware problem (such as the failure of HARD drive)

    Help, please

    Hello

    ·         Do you have a message of error during the installation of the driver fails?

    I suggest to uninstall the old drivers from Device Manager, then try to install the latest drivers for cash drawer and check if it works.

    How to configure devices by using Device Manager in Windows XP

    http://support.Microsoft.com/kb/307970

    See also:

     

    How to manage devices in Windows XP

    http://support.Microsoft.com/kb/283658

  • KB951847x86 fails to install Windows Update

    original title: windows update KB951847x86

    I have repeatedly tried to get this update. Whenever he fails. I never see a code error or a reason to explain why it does not. What else can I try?

    bhershey

    Hi bhershey,

    Try the following:

    Step 1: Locate the installation error code.

    To do this, follow these steps:

    a. click Start, click all programsand then click Windows Update or Microsoft Update.

    b. on the Windows Update Web site or on the Microsoft Update Web site, click view update history. A window opens that displays the updates that have been installed or that have failed to install on the computer.

    (c) in the State of this window column, find the update failed to install and then click on the red X. A new window opens that displays the installation error code.

    d. Note the error number.

    Step 2: Reset the Windows Update components, and then install the update. Visit the following link and click on Fixit.

    How to reset the Windows Update components?

Maybe you are looking for