1588 with no Ethernet device

Similar Questions

• I want to use my Time Capsule as a backup via ethernet device but it interfere with the Wi - Fi

  I bought a new Time Capsule (TC) to use as a backup device Time Machine.  Then, I learned that my place of work does not allow me to create my own wifi network.  I connected to the CT with an ethernet cable and turned off the wifi using Airport utility.  Automatic backups to decide using just the cable ethernet, as expected.  However, whenever I plug the ethernet cable from the TC to my laptop (MacBook Pro under OS X 10.10.5), the laptop refuses to use the actual wifi to my work network.  It's like the ethernet connection turns off the wifi connection, even if the laptop is always connected to the wifi (according to the network in the banner at the top of the screen icon).  Unplug the cable immediately gives me access wifi again.

  Any suggestions on how to disable this "feature" where to plug the ethernet cable disables the wifi connection?  Thank you very much!

  Note that I have not connected to the LAN Time Capsule.  It is completely autonomous.

• The WAN Port is communicating with the Ethernet switch?

  I have a Comcast gateway that the router is disabled in so it acts only as a modem. This is related to an Airport Extreme, which serves as my router via the WAN on the AE port. I created a different WAP with a Capsule temporal from the airport, located downstairs with an Ethernet cable from one of the Ethernet ports on the AE to the WAN on the TC port. I think it's what we call a 'roaming network.

  My question is, can I connect my switch Gigabit 8 ports in one of the Ethernet ports on the TC to complete connections wired to all devices connected on it, or should I first connect EI to the switch 8 ports and then connect the switch to the port WAN TC to complete my network "roaming"? In other words, plug it into the port WAN AE or TC still allows you to use other Ethernet ports as a switch?

  Thank you!

  can I plug my Gigabit 8 ports switch in one of the ports Ethernet on the TC to complete wired connections to all devices connected on it

  Yes, assuming that the TC has been configured to run in Bridge Mode, which would be normal.

  or should I first connect EI to the switch 8 ports and then connect the switch to the TC WAN port to complete my network "roaming"?

  It would be considered preferable to wiring, if it is convenient to do so.  For example, in the configuration of the wiring in the previous example just above... If there is a problem with the time Capsule, then all devices connected to the switch to the time Capsule would have a problem as well.

  If the switch is connected to the AirPort Extreme, and the TC is then connected to the switch... If the TC has a problem, the other devices connected to the switch of will not be affected.

• Why has my connection AirPort Extreme recently stopped with my Tablet Android and Windows 7 laptop, but connects very well with all Apple devices?

  Why has my connection AirPort Extreme recently stopped with my Tablet Android and Windows 7 laptop, but connects very well with all Apple devices?

  What exact model of AirPort Extreme do you have? Either have your tablet or laptop Win7 been updated recently? They were both able to connect before and not now OR they were never able to connect? Can the laptop Win7 access Internet when connected by Ethernet? One of these devices have problems connecting to other networks Wi - Fi?

• 2000-2d13CA HP: another ethernet device drivers controller/PCI device/PCI simple comunication/controller SM Bus

  I just reinstalled windows 7 on my HP 2000-2d13CA lappy, but problems with the following device drivers:

  Ethernet controller

  PCI device

  PCI simple communication controller

  SM Bus controller

  Please help with the procedure

  Hello:

  First install the smbus controller driver and restart the PC.

  This package contains the driver and Intel Chipset Installation Utility for the notebook models and operating systems. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager.

  File name: sp56670.exe

  Ethernet controller:

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp56680.exe

  PCI device:

  This package contains the driver that allows the Realtek card reader in laptop models running a supported operating system. The card reader allows users to read or write to removable storage cards supported, which are typically used in digital cameras, digital music players and cell phones.

  File name: sp64801.exe

  PCI simple communication controller:

  This package provides the driver Intel Management Engine Interface (MEI) for the notebook models and operating systems. The Intel Management Engine Interface allows communication between the host operating system and the Intel Management Engine firmware.

  File name: sp56675.exe

• With an Ethernet connection, should I also turn on WiFi?

  Is there any point of activation of my WiFi connection with an ethernet cable plugged into my iMac?  My printer can easily be connected via the USB port, and if I understand correctly, iCloud shares with my other devices can take place via ethernet or WiFi connection.

  My new iMac will be here next week and it's the only unresolved issue, I still have.

  Thanks for all the information provided here.  I rarely post, but read the comments here regularly and am amazed at the help and support provided.

  If that's what you're referring to:

  iCloud Photo Sharing FAQ - Apple Support

  You will need a cellular connection or WiFi for your iDevices; However, most of the time, this is accomplished by using a router that sends your (internet) signal throughout your home, your other devices to connect wirelessly. Thus, your Mac and your printer are good with Ethernet and, if you have a router (provided by your service provider internet or if you bought your own), you don't need WiFi enabled on your Mac. That's how I set it up at home.

• Problem with mobile MTP device connection of Samsung.

  Original title: Device

  I have problems with the devices. When I click my devices and printers, he claims that there is a problem with the driver for Samsung mobile MTP device but when I plug it costs and he finds all my photos. I tried troubleshooting and it says that there is a problem with the PnP device. What can I do to fix this? I have try the resolution of the problems, but it does not work. He also says that my pc Ethernet controller is not installed. Once, I tried troubleshooting but without prevail. If anyone can help with these issues it would be greatly appreciated. I tried a system restore, and it doesn't work anymore.

  Thank you very much

  Hi Chris,

  To provide the proper resolution, I would need more information on your side.

  1. which version of the operating system are you using?

  2. What is the brand and model of the computer?

  3. What is the exact model of the Samsung Mobile?

  4. what measures all troubleshooting have you tried?

  This problem may occur because of corrupted device driver.

  Method 1:
  I suggest you try the procedure described in the article and see if it helps.

  What to do when a device is not installed correctly
  http://Windows.Microsoft.com/en-us/Windows7/what-to-do-when-a-device-isn ' t-installed-correctly

  Method 2:
  If the problem persists, try to install the latest driver for Samsung mobile device MTP on the manufacturer's Web site.

  http://www.Samsung.com/us/support/supportMain.do

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• Error: "unable to communicate with the TWAIN device" with brother MFC7820N

  Original title: can I connect a scanner through a switch?

  I'm trying to analyze something like I did it many times with my brother MFC7820N hung on my tablet. But recently, I replaced a 2nd router I had in my system that failed with a new Dynex switch.

  I have my internet modem and 2 computers connected to a Linksys wireless router. I have another ethernet cable connecting the router to a new switch. I have my 2 printers attached to the switch. One is a Brother HL-2700CN color laser and the other is a brother MFC7820N mutli-function. It use PaperPort to scan stuff on him, since provided on the CD with the device.

  So today I open PaperPort and click the Scan button and it appeared an error saying unable to communicate with the TWAIN device box.

  So I clicked on a doc shown in PaperPort that I had scanned a few weeks ago and I click right and select Print and printed to this MFC7820N.

  Then I come back to click on scanner again and yet again, it appears that box. So I watch and WIA-Brother MFC-7820N LAN is displayed in the Scanner marked drop-down list box. So I switched the power of the MFC and tried again and it still appeared that same box again.

  OUCH! I'm going nuts! You have any ideas?

  Hi Jeff has Davis,
   
  Method 1: Uninstall and reinstall the driver again and check if it helps fix the problem.
   
  See this article for more information:
  How to manage devices in Windows XP
   
  Method 2: Try the suggestion given in this article:
  'Could not enable TWAIN Source' or 'He has not find scanner' Error Messages are displayed

• C7250 connected wireless works with wired ethernet PC but not wireless PC

  C7250 installs fine with static IP address and wired (ethernet) PC works perfectly, but is not recognized by the PC wireless.

  Can ping the IP of the PC cable but not wireless computers.

  Can connect to the IP address of the browser and can logon to the wired PCs of wireless computers.

  When the wireless PC is connected to the network with ethernet cable the C7250 works perfectly.

  Firewall is not the issue because I tested with the firewall disabled.

  Any suggestions?

  Thank you for your help.

  I FINALLY FOUND a RESOLUTION but let me describe what I've done to isolate the problem so that others will not do the same things I did.

  I used my Windows CE PDA and connected to the wireless router. I made sure that IE could access a different print server wired for a Brother HL-2140 I 192.168.2.10 and it worked. Who checked out that IE was working with a wired device. I then went to Yahoo!, and it worked. Then, I tried to access the C7250 configuration using IP 192.168.2.20 address in IE and it failed. (I checked with my Wired PC I could have access to the configuration of C7250 via IE.) I expected this result.

  Then I connected the PDA via USB and verified that I could use it to access the configuration of C7250 use IE on the PDA and it worked.

  I then tested between two wireless PC. Could not connect to each other through the router. But if one of them has been wired and one wireless they connected and I have consulted the disks between computers. I also tested the two cables with the same results.

  THE PROBLEM WAS IN THE ROUTER.

  These tests again virtually eliminated all PC, firewalls (since I've tested with the firewall disabled), the C7250 and the print server for the HL2140 brother as being the source of the problems.

  I then updated the firmware of the router to the latest version and repeated all the tests carried out in the complete thread and had the same results.

  RESOLUTION:
  The router I was using was a Linksys WRT54GS Ver 1.

  I also had a backup router which is a Linksys WRT54GS 7 worm that had the same settings as the Router 1 worm.

  I changed the SSID of the original router (Ver 1) so I would not need to change the SSID in all my devices during testing with the router Ver 7.

  I checked the firmware on the router worm 7 was the later and pulled up.

  The first test I did was to use a ping wireless PC the C7250 192.168.2.20 and it worked!

  I then used the wireless PC and IE to access the configuration of C7250 192.168.2.20 and it worked!

  I then checked the port for the C7250 was still a TCP/IP port to 192.168.2.20 and sent a test page to the printer and it worked!

  I consulted quickly wireless configuration C7250 and printer a test of a PC cable page and that worked!

  Finally, I tested PC wireless wireless PC PCand wired PC and the dirves successfully in both directions and checked that PC wired to wired PC was still working as before.

  All that remained was to supply two routers and router swap 1 worm with the Ver 7 router and rerun the tests with the router to Ver 7 manage my real network. Everything works as it should.

  I'll keep Router 1 worm as a backup to the Ver 7 knowing router unless the router worm 7 does not only feature that I lose when I reinstall the Router 1 worm is wireless connectivity to wireless, and I can temporarily work around until I get another router that is likely to be a "n" because what is have is ' G;

  THANK YOU FOR ALL YOUR HELP PRINTDOC!

  PRINTDOC BRAVO!

• Routing problem between the VPN Client and the router's Ethernet device

  Hello

  I have a Cisco 1721 in a test environment.

  A net 172.16.0.0/19 simulates the Internet and a net 192.168.1.0/24 simulates the net, the VPN tunnel must go to (intranet).

  The net 172.16.0.0 depends on the router 0 FastEthernet, Intranet (VPN) hangs on Ethernet 0.

  The configuration was inspired form the sample Configuration

  "Configuring the Client VPN Cisco 3.x for Windows to IOS using Local extended authentication"

  and the output of the ConfigMaker configuration.

  Authentication and logon works. Client receives an IP address from the pool. But there's a routing problem

  side of routers. Ping client-side - do not work (the VPN client statistics that count encrypt them packets, but not to decrypt).

  Ping the router works too, but decrypt and encrypt customer statistics in VPN packets count progressive

  (customer has a correct route and return ICMP packets to the router).

  The question now is:

  How to route packets between the Tunnel and an Ethernet device (Ethernet 0)?

  conf of the router is attached - hope that's not too...

  Thanks & cordially

  Thomas Schmidt

  -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- snipp .-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.

  !

  version 12.2

  horodateurs service debug uptime

  Log service timestamps uptime

  encryption password service

  !

  !

  host name * moderator edit *.

  !

  enable secret 5 * moderator edit *.

  !

  !

  AAA new-model

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  ! only for the test...

  !

  username cisco password 0 * moderator edit *.

  !

  IP subnet zero

  !

  audit of IP notify Journal

  Max-events of po verification IP 100

  !

  crypto ISAKMP policy 3

  3des encryption

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 3000client

  key cisco123

  pool ippool

  !

  ! We do not want to divide the tunnel

  ! ACL 108

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  interface Ethernet0

  no downtime

  Description connected to VPN

  IP 192.168.1.1 255.255.255.0

  full-duplex

  IP access-group 101 in

  IP access-group 101 out

  KeepAlive 10

  No cdp enable

  !

  interface Ethernet1

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP access-group 101 out

  full-duplex

  KeepAlive 10

  No cdp enable

  !

  interface FastEthernet0

  no downtime

  Description connected to the Internet

  IP 172.16.12.20 255.255.224.0

  automatic speed

  KeepAlive 10

  No cdp enable

  !

  ! This access group is also only for test cases!

  !

  no access list 101

  access list 101 ip allow a whole

  !

  local pool IP 192.168.10.1 ippool 192.168.10.10

  IP classless

  IP route 0.0.0.0 0.0.0.0 172.16.12.20

  enable IP pim Bennett

  !

  Line con 0

  exec-timeout 0 0

  password 7 * edit from moderator *.

  line to 0

  line vty 0 4

  !

  end

  ^-^-^-^-^-^-^-^-^-^-^-^-^- snapp ^-^-^-^-^-^-^-^-^-^-^-^-^-^-

  Thomas,

  Can't wait to show something that might be there, but I don't see here. You do not have the card encryption applied to one of the interfaces, perhaps it was not copied. Assuming your description you do it, or should it be, applied to the fa0 and you are connected. Try how you ping? Since the router or a device located on E0? If you ping the router, you will need to do an extended ping of E0 to the ip address of the client has been assigned. If your just ping the router without the extension, you will get sales and decrypts that you declare on the client. Have you tried to ping from the client to interface E0? Your default route on the router is pointing to fa0? You have a next hop to affect? You have several NIC on the client pc? Turn off your other network cards to check that you don't have a problem with routing on the client if you have more than one.

  Kurtis Durrett

• I have Mac syncs with my iOS devices.

  I have Mac syncs with my iOS devices.

  Why not? What happens when you try? We are not psychic.

• What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  You can connect otherwise?  USB or FireWire or love at first sight?  You can connect both machines and start the one you want to transfer to target disk mode.  If your other machine is up and running with an account on it and you just want to move files, you can simply drag and drop the FRO the machine mounted TDM, or you can use the migration wizard.

  Or, if the other machine still starts and runs, you can start both computers and connect to the same wifi network and share the hard drive like machines on the network.  Access them in the finder on the new machine files and drag-and - drop, or use the wizard migration, on wifi.

• Satellite M45-S359 equipped with a bluetooth device?

  Satellite M45-S359 equipped with a bluetooth device? Well, if it was, I don't know how to use uu

  Hello

  According to this page Bluetooth and antenna for Bluetooth device no is not available on this device.
  http://www.toshibadirect.com/TD/B2C/pdet.to?poid=306224&SEG=HHO

• How can I share my library with all my devices

  How can I share my library with all my devices?

  In the article to share your iTunes library on your home - network Support Apple its pretty simple from what I've read, just make sure you have sharing options enabled in iTunes on your computer.

  Just make sure that you are signed in the same Apple ID on all your devices and turn on sharing House on each of them as well and make sure that you are connected to the same network, trying to share the library.

• My iPhone6s pairs with ONE single device (phone link2cell). will pair with something else, and "bicycle wheel" changes all the time! Any suggestions?

  My iPhone6s pairs with ONE single device (phone link2cell). will pair with something else. At the opening of the Bluetooth window "bicycle wheel" next to "Other devices" is always running as if the search! Any suggestions?

  When you open the Bluetooth section in the settings, you can still see the spinning wheel, because it is in discovery mode and is actually looking for other devices in the range. Other devices must be in discovery/torque for the device mode to find them. However, I'm not sure you can be associated with multiple devices at the same time with the iPhone. You can have multiple devices matched on the phone, but you can always not more than one partner at the same time. It depends on what it is you are trying to pair.