160 U does not start after changing from 4 to 8 GB Ram

Similar Questions

• Pavilion dm3-2020eo does not start after change of RAM

  As the topic says my computer does not start after a change of the RAM.

  I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

  According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

  Can someone help me?

  Thank you
  Leo

  Here's the key:

  We're working on two sockets and one does not at all.

  You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

• Windows XP does not start after the installation of 3 GB of RAM. Will start with only 2 GB or less.

  I installed the new RAM on my desktop Compaq EVO D500.  Everything was working fine until 2 GB.  When I tried to install no matter what the computer does not start.  Specifications of the computer say maximum RAM is 3 GB.  All the memory and are good because I swapped taken in all the combinations possible and memory.  Any ideas. gknapp_ny

  If their were any memory related settings that had to be changed I would have no idea how do.  I had initially 512 MB of RAM (256-2 sticks).  I added a stick of 1 GB aditional third availabel taking and all went well.  Then I had two more identical 1 GB sticks and added them one at a time.  With 2 GB without problem.  But with the third stick of 1 GB that I couldn't start - I just beeps. I swapped one of the sticks of 1 GB for an old 256 MB and still no start just beeps.  When I run 2 GB everything is fine.  The BIOS recognizes the 2 GB of RAM. gknapp_ny

  Sounds as if your BIOS will not identify no matter what says the spec, 3 GB.

  It seems as if you may need a BIOS update in order to recognize the 3 GB of RAM - especially if it is a very old Compaq Evo D500.  See the "Improvements" tab to the page linked below.

  See http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=96295&swItem=PSG_I15378-37635&prodNameId=97121&swEnvOID=1093&swLang=13&taskId=135&mode=3

  Note that the patch on the link above is for models Evo D500 "with a ROM family 686Y2."  Read the "Release Notes" on this page to determine if your machine is one of those and if so, see "Instructions of Installation" to install the upgrade.  If your D500 is a laptop, you should Flash the ROM ONLY (i.e., update the BIOS level) when the computer is plugged - loss of power during this process can potentially cause irreparable harm to the computer.

• My copy registered and checked for XP Pro SP3 does not start after changing the motherboard. Second problem is that I can't find my original install of XP Pro disc.

  After failing to find the source of reliable performance from my PC, I decided to bite the bullet and replace the motherboard, memory and the CPU. I installed a triple base 435 Athlon and a motherboard Gigabyte MA74GMT. Awarded PC again started the first time - but Windows will not, I get a number of options but none work - safe mode brings up several lines of messages on the partition of multi (0) disk (0) rdisk (0).

  A previous post suggested that a similar message meant some kind of malware but if I replace the old motherboard, processor and memory Windows works very well - in fact I use it now.

  Do I have an option but to reinstall Windows from a CD? Otherwise I have a problem - I can't find the installation discs for each piece of software except my Windows XP Pro! I do repair discs?

  Thanks for your help.

  Hi DaGeLi,

  · Provide us with the complete message you receive.

  Follow the methods below:

  Method 1:

  You were able to start the first time, you can try to boot to the last known good configuration and check the results. Link to get the procedure please refer to: how to start your computer by using last good known Windows XP Configuration:http://support.microsoft.com/kb/307852

  Method 2:

  If it doesn't then you can follow the procedure from the below mentioned link. As you do not have the Windows XP CD you can follow the procedure if you have already installed on the computer to recovery console

  How do I recover from a corrupted registry that prevents Windows XP startup:http://support.microsoft.com/kb/307545

  Otherwise, you may need to make the boot floppies. See the link for the procedure below:

  http://support.Microsoft.com/kb/310994

  You can also contact the manufacturer of the system to get the Windows XP CD.

  For reference: how to fix a computer that does not start:http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx#2

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think

• DHCP service does not start after change of vmnetdhcp.conf

  Hello

  My installation includes a host running windows 8.1 pro and guest is an Oracle Linux 6.5 with NAT. As I searched for a static IP address for the comments I went ahead and added the following to the end of vmnetdhcp.conf

  host computer2 {}

  Hardware ethernet 00: 0C: 28:D9:D5:95

  fixed address - 192.168.37.3

  }

  As soon as I try to restart the dhcp service falls down. Even if I just restart machine job changes, the DHCP service does not start. When I do a reset of the network through the network Publisher configuration and simply accept a dynamic allocation of IP address to things normal race comments. The same configuration works fine on Windows 7 Pro host. Any help would be appreciated.

  Hello

  Thank you for using our product.

  I tried the same set upward on Win7 and Win8.1 host, both of them work well.

  So I guess that there is a syntax error when setting up vmnetdhcp.conf.

  Maybe missing ';' at the end of each line?

  An example would be like this:

  host computer2 {}

  Hardware ethernet 00: 0C: 28:D9:D5:95;

  fixed-address 192.168.37.3;

  }

  Please check and try again with kindness.

  Thank you!

• OptiPlex 755 USFF does not start after changing the cmos battery

  I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

  I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

  Any help would be appreciated.

  After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.

• Windows Vista does not start to change from IDE to AHCI in the BIOS

  Hi, I spent a lot of time to look at this problem online. I can't find a lot of google search results and they seem to say enter REGEDIT and change the "msahci" start to 0 and even the 'pciide', or 'iaStorV' start parameters to 0. But this does not work for me. The loading Windows with the loading bar screen Green just continues to go wrong and never Windows startup. I have Windows Vista Home Basic Edition.

  I saw someone in this forum with a similar problem but they have upgraded to Win7 on a new installation to fix the problem, they spend on AHCI RAID. I contacted Intel technical support and they said to try HP or the manufacturer of the motherboard. I contacted Intel because I installed a 520 Intel Solid State Drive series and wanted to know if they had a driver to get the benefit of the AHCI instead of the IDE. I know that a lot of people recommend a new installation of Windows, but I don't have a Windows cd with this computer (my computer is here: http://support.hp.com/us-en/document/c00835809 )

  I tried to install this Microsoft fix too. http://support.Microsoft.com/kb/922976

  I wonder if there is an AHCI driver, can I install it or what I can do to get the job of AHCI?

  Thanks to anyone who can help!

  I suggested that you create disks because you said that the computer came with any one and you could not re - install Windows as suggested a possible solution. With these records, you can the recovery of the system back to a factory State. Since you want to install a SSD or change a BIOS setting, these are the changes which can damage the system and require the use of recovery disks.

  If you want a Windows Vista 'clean' no HP Setup, please see Paul's response in this thread of the forum called "System Restore not working not not for HP Media Center Desktop PC. According to his instructions is expected to create a bootable Windows Vista installation disc. My only amendment to this method, is not to use the product key Microsoft Windows Vista on the COA on the side of your computer. Instead, I would like to "Save" the product key from factory OEM HP and HP OEM certificate using ' the Activation, backup and restore ' then 'restore' the certificate and the key to the new clean install of Vista. This will result in an installation clean factory activated that does not require Microsoft to activate. Be aware that the software HP added value will no longer be on your computer. If you want to use this software, you MUST create your personal HP recovery disks and copy the "SWSETUP" folder on your current installation of factory to an external support.

  Re-install Windows Vista, as shown above with the SATA BIOS settings set on AHCI you like will work 100% of the time. It should also install to SSDs, where HP recovery discs are known to fail.

• Virtual machine does not start after restoring from Time Machine to the new Imac

  I got my IMac replaced by Apple, after that they could not fix the old one.  They did a full restore from a Time Machine backup.  The virtual machine does not open now.   When I navigate to the file to try to open the virtual machine at the VMware logo in the bottom right of the icon displayed with large yellow exclamation appears on the icon?  Anyone encountered this problem before.  I'll take the Imac in Saturday if I can not solve.  The machine has the same size as before.  There are a few aspects of sharing with the Mac application miss me?

  According to the MacVirt.vmdk folder, you have the right number of segments of shared disk so you should be able to create a new VM by pointing to the disc in the new VM Wizard by pointing to the MacVirt.vmdk file.

  Note: After you create the new Virtual Machine, I would not suggest the Virtual Machine to stop, pause and close merge and then move all *.vmdk files in the package of the virtual machine, and then manually change the computer configuration files virtual .vmx and change the path to a little to view the MacVirt.vmdk file.  In this way, everything is in one package and is easier to maintain.

• VCenter Service does not start after changing the port number

  Hi all

  Accidentally, I changed the port number for the Vcenter server from the portal of VCenter 10443 and dint realize that the Java application uses 10443 so.

  Could not start the server vcenter service, because its raise an error saying 10443 port is already im currently byt used another application.

  I tried to stop the Java service, in order to start the vcenter service and make changes to port again, numbers but I am unable to stop the java application.

  Please, if anyone knows how to change the number of Vcenter via config port or any other way, please throw a comment... Its much appreciated.

  Thank you

  Nirmal

  If you use the MSSQL database, locate WebService.Ports.http in the VPX_PARAMETER table and change to the correct port.

• Service does not start after change of IP address on the server of SRM

  Here is the log.  The IP address has been changed, but I don't know how to take the side of MRS.?

  Journal of VMware Site Recovery Manager, pid = 4064, version = version 1.0.1 build-128004 =, = release, section = 2 option

  Cannot create the writer console

  Value flush dir "C:\Documents and Settings\All Users\Application Data\VMware\VMware Site Recovery Manager\DumpFiles"

  The initialization of the DBManager

  Current working directory: C:\Program VMware Site Recovery Manager\bin

  TaskMax = 10, IoMin = 1, IoMax = 21

  Try DrExternalRecoveryApi

  Plugin path 0: dr-external-recovery - api dll

  Absolute path of the plugin 0: C:\Program VMware Site Recovery Manager\bin\dr-external-recovery-api.dll

  Try RecoverySecondary

  Plugin path 1: dr-secondary - recovery.dll

  Absolute path of the plugin 1: C:\Program VMware Site Recovery Manager\bin\dr-secondary-recovery.dll

  Try SanProvider

  Plugin path 2: dr - san - provider.dll

  Absolute path of the plugin 2: C:\Program VMware Site Recovery Manager\bin\dr-san-provider.dll

  Try TestProvider

  Plugin 3 path: dr-test - provider.dll

  Absolute path of the plugin 3: C:\Program VMware Site Recovery Manager\bin\dr-test-provider.dll

  DrExtApi Instance of Service is initialized.

  Plugin has started.

  'SanProvider' provider has MoRef 'dr.primary.SanReplicationProvider:PrimarySanProvider '.

  Registered provider 'SanProvider '.

  'SanProvider' provider has MoRef 'dr.secondary.SanReplicationProvider:SecondarySanProvider '.

  Registered provider 'SanProvider '.

  Plugin has started.

  ' Provider 'TestProvider' has MoRef ' Dr. PrimaryTestProvider:primary - test provider.

  Registered provider 'TestProvider '.

  ' Provider 'TestProvider' has MoRef ' Dr. SecondaryTestProvider:secondary - test provider.

  Registered provider 'TestProvider '.

  Plugin has started.

  LocalSite already installed - good!

  Vmacore::InitSSL: doVersionCheck = true, handshakeTimeoutUs = 120000000

  VC connection: connection as the user "administrator."

  VC connection: logged in session F5EDC747-1344-4F98-82FB-038BB9D42933

  The specification of proxy for extension com.vmware.vcDr points to 172.20.0.168, not to this host

  Check with the local VC server is not valid

  Initialization of service content: unexpected exception 'class Vmacore::Exception' record with the local VC server is not valid

  Application error: check with local VC server is not valid. Closing...

  Unable to send the request. A new attempt. Error: class Vmacore::CanceledException (operation has been cancelled)

  VMware-Dr. service stopped

  Z OS

  I tried this on my own server and that you couldn't make it work.  I ended up just reinstall SRM, keeping the same database - NBD since most of the settings are there anyway.  Later, I came across a blog (which I can't find now) that said that VMware supports only a reinstall after changing the IP address.

• Satellite Pro L40 does not start after changing the BIOS settings

  Changed some settings in the bios last night and now when I boot I get a screen black lights flash and hard drive lights up but nothing on the screen.

  There is no password on the bios... How would a BIOS reset to normal?

  I put a windows disc now, I hear the disc spin but nothing on the screen

  (I think that I have come to the right place on the forum)

  It s a Toshiba Satellite Pro L40 model psl4be.

  Thank you

  > There was no bios password... How would a BIOS reset to normal?

  You can set the default BIOS ONLY inside the BIOS access BIOS by pressing F2 or at the beginning of the initialization of the order

  But I doubt that this problem is related to the BIOS.
  Maybe it s just a simple bad luck that this problem happened exactly after change something in the BIOS.

  Try connecting an external monitor and check if you can see something on the 2nd screen.

• Does not start after change of memory.

  Laptop HP dv6 - 2173cl

  Win7-64 bit

  I thought I had an easy task at hand... change my 2x2gb = 4 GB memory for 2 x 4 GB = 8 GB of memory.

  Removed old - replaced by the new.  Old and new are pc3-10600 (1333).

  When I got to the top of the laptop I had a screen with two options: enter the Startup Repair... or... start Windows normally.  I chose "repair startup'... only to be recycled to the screen option even.  Choose "Start Windows" gives me an error message and then sends me down to the option screen.

  I went into the bios... it shows memory 8132.  I did a test of memory in the bios and it says everything is ok.  Now, I run a test of marketing... and it's an hour in a check for two hours.

  I'm guessing that my new memory fights Win7... but I don't know why.

  Will be this "hard reset" I read about the work?  I can give up the test at startup?  Is there a downside for the hard reset?

  Help please.

  I found my answer over the weekend.

  Apparently there are modules of different memory... beyond the difference in office / laptop and 1600 Mhz / 1333 Mhz 2 Gb / 4 Gb... I had all these correct.  I found there are "not so high density ' and 'high density' chipsets chipsets.

  In the discussion of the chatbox says the seller of memory, "some systems will not use the high density of the smart parts J."

  I have the new shipping modules.  If the adventure continues I'll post more.

• Windows does not start after changing the partition with external software

  Hello

  I messed up and followed some bad advice.  Water under the bridge, but I want to recover my bootcamp partition if possible.  I've seen several messages with the right process, but decided to post hear instead of assumptions.  I am running OS X El Capitan on an early 2011 MacBook Pro.  My 256 GB SSD is a bit pressed and tried to be too stingy with the Boot Camp partition, so my current troubles after resizing.  I have 10 Windows on the bootcamp partition.

  I'm going to throw a bunch of data from my survey here.

  Capella: ~ list of the ronh$ diskutil

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 250,1 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage Macintosh HD 190,5 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 58.7 GB disk0s5

  / dev/disk1 (internal, virtual):

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS Macintosh HD GB + 190,2 disk1

  Logical volume on disk0s2

  B6DC811B-004D-4245-83C9-8FAA0B51FD9E

  Unencrypted

  Capella: ~ list of cs ronh$ diskutil

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group 487E3580-D1BE-4A6D-A33C-38C8DD8ABA34

  =========================================================

  Name: Macintosh HD

  Status: online

  Dimensions: 190546800640 B (190.5 GB)

  Free space: 19005440 B (19.0 MB)

  |

  +-< physical="" volume="">

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 190546800640 B (190.5 GB)

  |

  + -> 37BE876E-8E51-47C3-8D62-001EC021DE56 family of Logical Volume

  ----------------------------------------------------------

  Encryption type: no

  |

  +-> Logical Volume B6DC811B-004D-4245-83C9-8FAA0B51FD9E

  ---------------------------------------------------

  Disc: disk1

  Status: online

  Size (Total): 190175473664 B (190.2 GB)

  Reversible: Yes (no required decryption)

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  Capella: ~ ronh$ sudo TPG - vv - r show/dev/disk0

  Password:

  See the TPG: / dev/disk0: mediasize = 250059350016; SectorSize = 512; blocks = 488397168

  See the TPG: / dev/disk0: MBR suspicious to sector 0

  See the TPG: / dev/disk0: Pri GPT to sector 1

  See the TPG: / dev/disk0: GPT Sec at sector 488397167

  start index size summary

  0 1 MBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 372161720 2 part TPG - 53746F72-6167-11AA-AA11-00306543ECAC

  372571360 1269536 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  373840896 1024

  373841920 114554880 5 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  335 488396800

  488397135 32 table dry GPT

  488397167 1 dry GPT header

  of gdisk.

  Command (? for help): p

  Disk/dev/rdisk0: 488397168 sectors, GiB 232.9

  Logical sector size: 512 bytes

  Identifier (GUID) of disc: FD5932B4-069B-4CCE-A2EE-99AB5720CA17

  Partition table contains up to 128 entries

  First usable sector is 34, last usable area is 488397134

  The partitions will be aligned with the boundaries of sector 8

  Total free space is 1365 sectors (682,5 KiB)

  Starting number (sector) end (sector), Code name of size

  409639 40 1 200.0 of MiB EF00 EFI system partition

  2 409640 372571359 177.5 giB AF05 Macintosh HD

  3 372571360 373840895 619.9 MiB AB00 Recovery HD

  5 373841920 488396799 54.6 giB 0700 BOOTCAMP

  

  It is worth spending time to recover?  Thank you.

  Ron

  1. can you describe the problem and the steps you took to get here?

  2 can scroll you down to the next MS data (after that highlighted) and press 'p' to the list of files? Press ESC, once only, to return to this list.

• Computer does not start after changing permissionl

  I had bad to put files on my hard drive without signature every time. I have made some changes in permissions and must have inadvertently changed everyone to access, because now my computer will not boot. He gets the white Apple on black background and goes just about a third of the way and stops. Have I blocked the drive permanently. It doesn't have a cd/dvd drive, so I have no boot disk. It was running 10.10.5. The only thing I have is a USB key with 10.9 on it. Elbow of desperate here and I'd appreciate any help anyone could offer.

  jwm48

  iMac (27 inch, at the end of 2013)

  Click here and follow the instructions.

  (143633)

• Touchpad does not work after changing from Vista to XP Satellite A210

  Hello world!

  I changed my Windows and now, something is wrong with the Touchpad. It works like a mouse (the cursor moves right and left buttons are also correct).

  Before with Vista, I had the button send, Wi - Fi connection, something else and its evolution, and more he had extra blue light. Now these buttons are not active and not etrxa of light.

  Satellite A210 laptop.

  I already tried all possible drivers, but perhaps you could advice me something else.

  Thanks in advance!

  Please try this one
  http://Support1.toshiba-tro.de/Tedd-files2/0/tpdrv-20070809133247.zip

  and give us your feedback if this driver can help or not
  THX