1811 VPN - cannot access subnets

Similar Questions

• RVL200 SSL VPN: cannot access a remote LAN with iPad2

  RVL200 firmware 1.1.12.1

  iPad2 cannot access any device on the Remote LAN despite the closed padlock icon.

  Is there another App needed? Or how to debug SSL VPN?

  Emmanuel,

  Were you able to access the LAN devices? Also, have you connected using a Mac or a PC successfully to verify that the devices are available? Sometimes antivirus and firewall software can block access to devices from a remote IP address.

• ASA 5505 VPN cannot access inside the host

  I have access remote VPN configuration on an ASA 5505, but cannot access the host or the AAS when I connect through the VPN. I can connect with the Cisco VPN client and the VPN is on on the SAA and it shows that I am connected. I have the correct Ip address, but I can't ping or you connect to one of the internal addresses. I can't find what I'm missing. I have the VPN without going through the ACL interface. Because I can connect but not going anywhere I'm sure I missed something.

  framework for configuration below

  interface Vlan1

  nameif inside

  security-level 100

  10.1.1.1 IP address 255.255.255.0

  IP local pool xxxx 10.1.1.50 - 10.1.1.55 mask 255.255.255.0

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 set pfs

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  PFS set 40 crypto dynamic-map outside_dyn_map

  Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA

  Crypto-map dynamic inside_dyn_map 20 set pfs

  Crypto-map dynamic inside_dyn_map 20 the value transform-set ESP-3DES-SHA

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  map inside_map 65535-isakmp ipsec crypto dynamic inside_dyn_map

  inside crypto map inside_map interface

  crypto ISAKMP allow inside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  global service-policy global_policy

  XXXXXXX strategy of Group internal

  attributes of the strategy group xxxxxxx

  banner value xxxxx Site Recovery

  WINS server no

  24.xxx.xxx.xx value of DNS server

  VPN-access-hour no

  VPN - connections 3

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  by default no

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout no

  disable the IP-phone-bypass

  disable the leap-bypass

  disable the NEM

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  the address value xxxxxx pools

  enable Smartcard-Removal-disconnect

  the firewall client no

  WebVPN

  url-entry functions

  Free VPN of CNA no

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  tunnel-group xxxx type ipsec-ra

  tunnel-group xxxx general attributes

  xxxx address pool

  Group Policy - by default-xxxx

  blountdr group of tunnel ipsec-attributes

  pre-shared-key *.

  Missing nat exemption for vpn clients. Add the following and you should be good to go.

  inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0

  NAT (inside) 0-list of access inside_nat0_outbound

• PIX501 customer VPN - cannot access inside the network with VPN Session

  What follows is based on the config on the attached link:

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a008009442e.shtml

  PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC

  We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.

  Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!

  We have the same problem with the customer 4.0.3(c)

  Thanks in advance for any help!

  =======================================

  AKCPIX00 # sh run

  : Saved

  :

  6.2 (3) version PIX

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  hostname AKCPIX00

  domain.com domain name

  fixup protocol ftp 21

  fixup protocol http 80

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol they 389

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol sip 5060

  fixup protocol 2000 skinny

  fixup protocol sip udp 5060

  names of

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0

  pager lines 24

  interface ethernet0 10baset

  interface ethernet1 10full

  Outside 1500 MTU

  Within 1500 MTU

  external IP address #. #. #. # 255.255.240.0

  IP address inside 192.168.1.5 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  IP local pool akcpool 10.0.0.1 - 10.0.0.10

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  RADIUS Protocol RADIUS AAA server

  AAA-server local LOCAL Protocol

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Permitted connection ipsec sysopt

  No sysopt route dnat

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 10 transform-set RIGHT

  map mymap 10-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  ISAKMP allows outside

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  vpngroup address akcpool pool akcgroup

  vpngroup dns 192.168.1.10 Server akcgroup

  vpngroup akcgroup by default-domain domain.com

  vpngroup split tunnel 101 akcgroup

  vpngroup idle 1800 akcgroup-time

  vpngroup password akcgroup *.

  vpngroup idle 1800 akc-time

  Telnet timeout 5

  SSH #. #. #. # 255.255.255.255 outside

  SSH timeout 15

  dhcpd address 192.168.1.100 - 192.168.1.130 inside

  dhcpd dns 192.168.1.10

  dhcpd lease 3600

  dhcpd ping_timeout 750

  dhcpd allow inside

  Terminal width 80

  Cryptochecksum:XXXXX

  : end

  AKCPIX00 #.

  Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:

  mymap outside crypto map interface

  ISAKMP allows outside

  Enter these two commands should be enough to reset the ipsec and isakmp.

• Client VPN cannot access the different internal subnet

  Hi all

  I use pix 7.0 and 4,8 vpn client

  When I connect with the vpn client, I see the subnet behind the pix (10.61.1.0)

  However, there is a router on that subnet that connects to two other sites (10.61.2.0 and 10.72.2.0)

  I can ping from the pix to these subnets command line.

  When I connect using the vpn client I only see the subnet behind the pix and not the other two subnets?

  I have a command-line 10.0.0.0 255.0.0.0 10.61.1.250 (the ip address of the router) on the pix, but this doesn't seem to help?

  The response from the ping is request timed out one or the other subnets.

  Any suggestions on what route, I need to add or is there an ACL to be added?

  Current and ACL routes is:

  0.0.0.0 0.0.0. The ISP router address

  10.0.0.0 255.0.0.0 10.61.1.250

  Outside_access_in list extended access permit icmp any one

  access extensive list ip 10.61.1.0 inside_nat0 allow 255.255.255.0 10.61.1.224 255.255.255.240

  NAT (inside) 0-list of access inside_nat0

  NAT (inside) 10 0.0.0.0 0.0.0.0

  Access-group Outside_access_in in interface outside

  All responses appreciated.

  first of all and above all, the pool of the vpn client should not overlap with the asa inside the subnet, or any connected subnet.

  <-->Asa <-->(10.61.1.250) Internet router <-->10.61.2.0 and 10.72.2.0

  allow inside_nat0 to access extended list ip 10.61.1.0 255.255.255.0

  allow inside_nat0 to access extended list ip 10.61.2.0 255.255.255.0

  allow inside_nat0 to access extended list ip 10.72.2.0 255.255.255.0

  Allow Outside_cryptomap_dyn_20 to access extended list ip 10.61.1.0 255.255.255.0

  Allow Outside_cryptomap_dyn_20 to access extended list ip 10.61.2.0 255.255.255.0

  Allow Outside_cryptomap_dyn_20 to access extended list ip 10.72.2.0 255.255.255.0

  In addition, a static route must be configured on the 10.61.1.250 router:

  IP route

• Cannot access subnet when VPN would be

  When I vpn in our network, it gives me an ip address in the range: 192.168.200.1 - 192.168.200.50.

  The following access works when vpn would be: 192.168.200.x-> 10.2.28.x

  Made following access does not work when the vpn would be: 192.168.200.x-> 192.168.50.x

  Can you get it someone please let me know what I have in the PIX config to make it work?

  Thank you

  Thomas

  1. Add 192.168.50.0 to your acl of split tunnel

  remotevpnbhc_splitTunnelAcl 192.168.50.0 ip access list allow 255.255.252.0 all

  2. Add the traffic between the client vpn and 192.168.50.0 ACL that is used by NAT 0

  vpn_insideacl ip 192.16.50.0 access list allow 255.255.252.0 192.168.200.0 255.255.255.0

• On ASA 5505 VPN cannot access remote (LAN)

  I have an ASA 5505 upward and running, all static NAT statements I need to forward ports to the internal services such as smtp, desktop remotely and it works very well, however I have set up an IPSEC vpn connection that authenticates to our DC and part works. However, after I connect and cannot ping anything on the local network or access services. I don't know what a NAT statement I have corrected. Here is the config. I really need to get this up and going tomorrow. Thanks for any help.

  Tyler

  Just remove the line of nat (outside) and ACL outside_nat0_outbound.

  And talk about these statements:

  IPSec-1 sysopt connection permit... (If it is disabled, you can check with sh run sysopt).

  2, crypto isakmp nat traversal 10 or 20

  3 no NAT ACL, mention your local subnets as the source and vpn client as the destination.

  4, create the other ACL (ST) with different name and source and destination like no nat ACL.

  5, then type nat (inside) 0 access-list sheep

  6, in the dwgavpn group policy, talk to splittunnel tunnelspecified and mention the tunnel split ACL (ST).

  Concerning

• Remote VPN cannot access devices LAN or internet

  So I have a server and a computer inside that I can access through an ASA 5505 with ASA 9.2 (1) and ASDM 7.2 (1)

  The computer on 192.168.1.110 via port 8080 can show me a demo site.

  The server on 192.168.1.222 got my DNS, HTTP, FTP, mail and more about it.

  Outside, I got a computer (by outside, I hear from the firewall and the cable directly into the computer) on 192.168.20.2 and firewall outside being 192.168.20.1

  From the outside I can access the 8080 without problem (and I guess as well with the server, but it is on another default gateway and are not accessible right now). -When I connect through my VPN I am assigned 192.168.30.5 but unable to connect inside the computer through 192.168.1.110:8080.

  This will return the error: asymmetrical NAT rules matched for before and back flow; Connection for udp src outdoors: 192.168.30.5/49608 (...) dst inside: 192.168.1.222/53 refused because of the failure of the path reverse NAT.

  Somewhere, I had a conflict or a non-created access rule. Anyone who wants to take a shot?

  I marked with "BOLD" for what I thought that may be the cause.

  ciscoasa (config) # sh running-config
  : Saved
  :
  ASA Version 9.2 (1)
  !
  ciscoasa hostname
  activate 8Ry2YjIyt7RRXU24 encrypted password
  volatile xlate deny tcp any4 any4
  volatile xlate deny tcp any4 any6
  volatile xlate deny tcp any6 any4
  volatile xlate deny tcp any6 any6
  volatile xlate deny udp any4 any4 eq field
  volatile xlate deny udp any4 any6 eq field
  volatile xlate deny udp any6 any4 eq field
  volatile xlate deny udp any6 any6 eq field
  2KFQnbNIdI.2KYOU encrypted passwd
  names of
  192.168.30.5 mask - 192.168.30.200 local pool Pool of IP IP 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.254 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  address 192.168.20.1 255.255.255.0
  !
  boot system Disk0: / asa921 - k8.bin
  passive FTP mode
  permit same-security-traffic intra-interface
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  object network testServer-8080
  host 192.168.1.110
  Description of the test server
  network of the object server-21
  Home 192.168.1.222
  Description of the test server
  network of the object Server-25
  Home 192.168.1.222
  Description of the test server
  network of the object Server-53
  Home 192.168.1.222
  Description of the test server
  network of the object server-80
  Home 192.168.1.222
  Description of the test server
  network of the object server-443
  Home 192.168.1.222
  Description of the test server
  network of the object server-2525
  Home 192.168.1.222
  Description of the test server
  network of the object server-993
  Home 192.168.1.222
  Description of the test server
  network of the object server-6001
  Home 192.168.1.222
  Description of the test server
  network of the object server-6002
  Home 192.168.1.222
  Description of the test server
  network of the object server-6003
  Home 192.168.1.222
  Description of the test server
  network of the object server-6004
  Home 192.168.1.222
  Description of the test server
  network of the VPN HOST object
  192.168.30.0 subnet 255.255.255.0
  network of the object inside
  host 192.168.1.0
  the vpn server object network
  Home 192.168.1.222
  outside_access_in list extended access permit tcp any object testServer-8080 eq 8080
  outside_access_in list extended access permit tcp any object server-21 eq ftp
  outside_access_in list extended access permit tcp any object Server-25 eq smtp
  outside_access_in list extended access permit tcp any object server-2525 2525 eq
  outside_access_in list extended access permit udp any object server-53 eq inactive field
  outside_access_in list extended access permit tcp any object server-80 eq www
  outside_access_in list extended access permit tcp any object server-443 https eq
  outside_access_in list extended access permit tcp any object server-993 993 eq
  outside_access_in list extended access permit tcp any object server-6001 eq 6001
  outside_access_in list extended access permit tcp any object server-6002 6002 eq
  outside_access_in list extended access permit tcp any object server-6003 eq 6003
  outside_access_in list extended access permit tcp any object server-6004 eq 6004
  outside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.30.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 721.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) VPN-dynamic HOSTS within static destination to source Server VPN - vpn server
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  object network testServer-8080
  NAT (inside, outside) interface static 8080 8080 tcp service
  network of the object server-21
  NAT static (inside, inside) of the service ftp ftp tcp interface
  network of the object Server-25
  NAT (inside, outside) interface static tcp smtp smtp service
  network of the object Server-53
  NAT static (inside, inside) interface tcp service area
  network of the object server-80
  NAT (inside, outside) interface static tcp www www service
  network of the object server-443
  NAT (inside, outside) interface static tcp https https service
  network of the object server-2525
  NAT (inside, outside) interface static 2525 2525 tcp service
  network of the object server-993
  NAT (inside, outside) interface static tcp 993 993 service
  network of the object server-6001
  NAT (inside, outside) interface static tcp 6001 6001 service
  network of the object server-6002
  NAT (inside, outside) interface static tcp 6002 6002 service
  network of the object server-6003
  NAT (inside, outside) interface static 6003 6003 tcp service
  network of the object server-6004
  NAT (inside, outside) interface static service tcp 6004 6004
  Access-group outside_access_in in interface outside
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS AAA server HSS-auth-server protocol
  allow only
  AAA-server HSS-auth-server (inside) host 192.168.1.222
  Timeout 5
  key *.
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  trustpool crypto ca policy
  Crypto isakmp nat-traversal 30
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  authentication crack
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 20
  authentication rsa - sig
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 40
  authentication crack
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 50
  authentication rsa - sig
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 60
  preshared authentication
  aes-192 encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 70
  authentication crack
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 80
  authentication rsa - sig
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 90
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 100
  authentication crack
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 110
  authentication rsa - sig
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 120
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 130
  authentication crack
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 140
  authentication rsa - sig
  the Encryption
  sha hash
  Group 2
  life 86400
  IKEv1 crypto policy 150
  preshared authentication
  the Encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0

  dhcpd outside auto_config
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  internal HSSvpn group strategy
  attributes of Group Policy HSSvpn
  value of server DNS 192.168.1.222
  Ikev1 VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value outside_access_in ! This value was its own name earlier
  HSS.dk value by default-field
  type tunnel-group HSSvpn remote access
  attributes global-tunnel-group HSSvpn
  address IP-pool pool
  HSS-auth-server authentication-server-group
  Group Policy - by default-HSSvpn
  password-management
  IPSec-attributes tunnel-group HSSvpn
  IKEv1 pre-shared-key *.
  tunnel-group HSSvpn ppp-attributes
  No chap authentication
  no authentication ms-chap-v1
  ms-chap-v2 authentication
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:9859258e11364180cf9b3e21173b3f2f
  : end

  Hello

  "Nat" bold configuration is incorrect, as you would expect.

  Replace it with something like this

  the object of the LAN network
  subnet 192.168.1.0 255.255.255.0

  NAT (inside, outside) 1 static source LAN LAN to static destination HOST-VPN-VPN-HOST

  I also suggest using a separate access the ACL of the Tunnel from Split 'standard' list.

  For example

  standard SPLIT-TUNNEL access list permit 192.168.1.0 255.255.255.0

  Naturally, you must pass the ACL above to used "group policy" .

  In addition, if you want to control the incoming connections to VPN users in 'outside_access_in' ACL, then you could change the default settings on the SAA by running the command

  No vpn sysopt connection permit

  If you need to return back then just to deliver without 'no' in front. Then back to its default value. This does not show in the running configuration by the way.

  With this setting all connections from VPN connections should be allowed on the interface ACL interface that ends the VPN connection. If in your case that would be the ACL attached to the 'outside' interface.

  Hope this helps :)

  -Jouni

• PIX - PIX VPN and Client VPN - cannot access core network

  I hub and spoke PIX and a VPN Client that connects to speak it PIX, much the same as the example configuration here: -.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00800948b8.shtml

  This example shows the client VPN access to the network behind PIX RADIUS. I want the client to also be able to access the central network, i.e. the client connects to the pix speaks via vpn, and traffic is routed through the vpn to PIX - PIX to the central site.

  How this would change the configuration contained in the example?

  See you soon,.

  Jon

  You can not do this, the PIX cannot route a package back on the same interface, it is entered in the. The only way to do that is to have the client connect to the hub PIX, but then they would not be able to get to the network behind PIX distance either.

  Or that the customer would connect on a different interface in the PIX of distance, but this would mean another connection ISP on this PIX. Example of config is here: http://www.cisco.com/warp/public/110/client-pixhub.html

• Client VPN cannot access anything at the main Site

  I am sure that this problem has been resolved in a million times more, but I can't get this to work.  Can someone take a look at this quick config and tell me what is the problem?

  The Cisco VPN client connects without problems but I can't access anything whatsoever.

  ASA Version 8.4 (4)

  !

  ciscoasa hostname

  activate 8Ry2YjIyt7RRXU24 encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  switchport access vlan 15

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.43.254 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address a.a.a.a 255.255.255.248

  !

  interface Vlan15

  prior to interface Vlan1

  nameif IPOffice

  security-level 100

  IP 192.168.42.254 255.255.255.0

  !

  boot system Disk0: / asa844 - k8.bin

  passive FTP mode

  network object obj - 192.168.43.0

  192.168.43.0 subnet 255.255.255.0

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  network of the NETWORK_OBJ_10.11.12.0_24 object

  10.11.12.0 subnet 255.255.255.0

  network of the NETWORK_OBJ_192.168.43.160_28 object

  subnet 192.168.43.160 255.255.255.240

  network of the IPOffice object

  subnet 0.0.0.0 0.0.0.0

  outside_access_in list extended access permit icmp any 192.168.42.0 255.255.255.0

  Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel

  standard access list vpn_SplitTunnel allow 192.168.43.0 255.255.255.0

  AnyConnect_Client_Local_Print deny ip extended access list a whole

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd

  Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631

  print the access-list AnyConnect_Client_Local_Print Note Windows port

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100

  access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353

  AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355

  Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137

  AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  MTU 1500 IPOffice

  IP local pool newvpnpool 10.11.12.100 - 10.11.12.150 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 649.bin

  don't allow no asdm history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.11.12.0_24 NETWORK_OBJ_10.11.12.0_24 non-proxy-arp-search to itinerary

  NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.43.160_28 NETWORK_OBJ_192.168.43.160_28 non-proxy-arp-search to itinerary

  NAT (IPOffice, outside) static source any any static destination NETWORK_OBJ_192.168.43.160_28 NETWORK_OBJ_192.168.43.160_28 non-proxy-arp-search to itinerary

  !

  network obj_any object

  NAT dynamic interface (indoor, outdoor)

  network of the IPOffice object

  NAT (IPOffice, outside) dynamic interface

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 b.b.b.b 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  AAA authentication http LOCAL console

  AAA authentication LOCAL telnet console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 0.0.0.0 0.0.0.0 outdoors

  http 192.168.43.0 255.255.255.0 inside

  http 192.168.42.0 255.255.255.0 IPOffice

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  IKEv1 crypto ipsec transform-set high - esp-3des esp-md5-hmac

  crypto ipsec transform-set encrypt method 1 IKEv1 esp-3des esp-sha-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  Crypto-map dynamic dynmap pfs set 30 Group1

  Crypto-map dynmap 30 set transform-set ikev1 strong dynamic - a

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  map rpVPN 65535-isakmp ipsec crypto dynamic dynmap

  rpVPN interface card crypto outside

  crypto isakmp identity address

  Crypto ikev1 allow outside

  IKEv1 crypto policy 1

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 2

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  SSH group dh-Group1-sha1 key exchange

  Console timeout 0

  dhcpd outside auto_config

  !

  dhcpd address 192.168.43.5 - 192.168.43.36 inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-2.4.1012-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  internal RPVPN group policy

  RPVPN group policy attributes

  value of server DNS 8.8.8.8

  Ikev1 VPN-tunnel-Protocol

  username admin privilege 15 encrypted password gP3lHsTOEfvj7Z3g

  username password encrypted blPoPZBKFYhjYewF privilege 0 mark

  type tunnel-group RPVPN remote access

  attributes global-tunnel-group RPVPN

  address newvpnpool pool

  Group Policy - by default-RPVPN

  IPSec-attributes tunnel-group RPVPN

  IKEv1 pre-shared-key *.

  !

  !

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:b3f15dda5472d65341d7c457f2e8b2a2

  : end

  Well Yes, you are quite right on site!

  Asymmetric routing is not supported on the firewall, such as trafficking and out should be via the interfaces of same, in the contrary case, it think it's an attack and drop the package.

  Default gateway on the subnet devices IPOffice should be the interface IPOffice ASA (192.168.42.254), not the switch, if it is a switch shared with your home network. Similarly for devices inside subnet, default gateway must be ASA 192.168.43.254.

  In regards to the switch, you can get a default gateway or the ASA inside or IP interface IPOffice ASA and the needs of return traffic to route through the same path

• RV320 VPN cannot access peripheral LAN using iPad

  With the help of RV320, firmware 1.1.1.06

  LAN 192.168.1.x 255.255.255.0

  VPN 192.168.09.100 to 192.168.09.150

  I need to access a device on the local network using this VPN connection from iPad. The Unit received address DHCP on LAN, broadcasts its presence every second on the Port 4992.

  When it is on the LAN, the iPAD sees the presence of broadcasting and accesses the device without problem. When I VPN in, easy VPN works well. I configured the firewall of the router as the rules:

  Allow

  All traffic [1]

  LAN

  192.168.9.100 ~ 192.168.9.150

  192.168.1.1 ~ 192.168.1.255

  Always

  Allow

  All traffic [1]

  LAN

  192.168.1.1 ~ 192.168.1.255

  192.168.9.100 ~ 192.168.9.150

  Alway

  If I first connect to the device when the iPad is on the local network, I turn off WiFi and connect through the VPN, I can continue to control the device. However, if I'm not connected to the device locally first, I see the presence broadcast on port 4992 when it connects first via the VPN. Broadcasting does not reach the iPad from a 192.168.1.x device connected 192.168.9.x.

  What is the correct way for the iPad on the 192.168.9.x, see the dissemination of 192.168.1.x?

  Hello

  Broadcasts will not be sent on the VPN tunnel.  The only traffic that will pass from the LAN to your customer's traffic specifically aimed at it, otherwise the router send him outside.  Looks like your presence Pack is a show, so all VPN clients won't be able to see.

  I think that when you connect locally you are picking up on the broadcast and then when you go to the VPN that has not passed yet, so why does it work if you connect locally first.

  Hope that helps a little,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• remote VPN cannot access mail server of asa

  Hi dear.

  I have the router that connect to the asa.

  Internet line to connect to the router so all the nat translation is made to the router.

  router outside the ip:x.x.xx

  router inside the ip:10.0.0.1 interface that is connect to asa outside interface (asa outside ip address: 10.0.0.2)

  my mail server to connect to the DMZ asa.

  DMZ interface ip address:172.16.10.0./24

  mail server IP:172.16.10.10

  I'm twice nat for the ip address of the mail server.

  1.i do to asa.

  static (DMZ, Outside) 10.0.0.10 172.16.10.10

  in this mail server ip 172.16.10.10 translation translating 10.0.0.10(10.0.0.10 ip est un sous-réseau de la plage de connexion routeur et asa).

  second nat to router.

  IP nat inside source static tcp 10.0.0.10 25 25 ext x.x.x.x public ip x.x.x.x

  I have no problem with my nat translation to my e-mail server.

  I have set up remote client vpn to asa and apply crypto map ASA outside interface which is 10.0.0.2

  I do THE static nat router for asa outside ip address.

  IP nat inside source static udp 10.0.0.2 x.x.x.x extensible 500 500

  IP nat inside source static udp 10.0.0.2 4500 4500 extensible x.x.x.x

  I have no problem with the vpn connection. I can connect vpn connection. but I can't access mail server. 172.16.10.10

  What can I do in this situation?

  I should be writing sheep-access list?

  If Yes, how can I write this access list?

  Yes, you must configure access on your ASA sheep-list as follows:

  IP 172.16.10.0 allow Access-list sheep-dmz 255.255.255.0

  NAT 0 access-list sheep-dmz (dmz)

• ASA 5505 VPN cannot access inside hosts

  I set up VPN on the using 5505 ASDM and I am able to connect to the 5505 and the customer is also getting an IP address from the configured pool.

  The Cisco VPN client displays an error in the log: AddRoute cannot add a route: code 87

  Cisco

  You may need to nat traversal lit. Try to add crypto isakmp nat-traversal 3600

• AnyConnect VPN users cannot access remote subnets?

  I googled this until blue in the face without result.  I don't understand why Cisco this so difficult?  When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices.  What should I do to allow my anyconnect vpn clients access to my remote sites?

  Cisco 5510 8.4

  Hello

  What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.

  In addition to routing, you must have configured for each remote site and the VPN pool NAT0

  Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this

  object-group network to REMOTE SITES

  object-network 10.10.10.0 255.255.255.0

  object-network 10.10.20.0 255.255.255.0

  object-network 10.10.30.0 255.255.255.0

  object-network 10.10.40.0 255.255.255.0

  network of the VPN-POOL object

  10.10.224.0 subnet 255.255.255.0

  NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL

  The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.

  Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.

  My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)

  Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?

  -Jouni

• Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

  I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

  Thank you

  interface Ethernet0/0

  Speed 100

  full duplex

  nameif outside

  security-level 0

  IP x.x.x.x 255.255.255.240

  !

  interface Ethernet0/1

  Speed 100

  full duplex

  nameif inside

  security-level 100

  IP 10.88.10.254 255.255.255.0

  !

  interface Management0/0

  Shutdown

  nameif management

  security-level 0

  no ip address

  !

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PAT_to_Outside_ClassA object

  10.88.0.0 subnet 255.255.0.0

  network of the PAT_to_Outside_ClassB object

  subnet 172.16.0.0 255.240.0.0

  network of the PAT_to_Outside_ClassC object

  Subnet 192.168.0.0 255.255.240.0

  network of the LocalNetwork object

  10.88.0.0 subnet 255.255.0.0

  network of the RemoteNetwork1 object

  Subnet 192.168.0.0 255.255.0.0

  network of the RemoteNetwork2 object

  172.16.10.0 subnet 255.255.255.0

  network of the RemoteNetwork3 object

  10.86.0.0 subnet 255.255.0.0

  network of the RemoteNetwork4 object

  10.250.1.0 subnet 255.255.255.0

  network of the NatExempt object

  10.88.10.0 subnet 255.255.255.0

  the Site_to_SiteVPN1 object-group network

  object-network 192.168.4.0 255.255.254.0

  object-network 172.16.10.0 255.255.255.0

  object-network 10.0.0.0 255.0.0.0

  outside_access_in deny ip extended access list a whole

  inside_access_in of access allowed any ip an extended list

  11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

  outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

  mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

  NAT static NatExempt NatExempt of the source (indoor, outdoor)

  NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

  NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

  NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

  !

  network of the PAT_to_Outside_ClassA object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassB object

  NAT dynamic interface (indoor, outdoor)

  network of the PAT_to_Outside_ClassC object

  NAT dynamic interface (indoor, outdoor)

  Access-group outside_access_in in interface outside

  inside_access_in access to the interface inside group

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

  dynamic-access-policy-registration DfltAccessPolicy

  Sysopt connection timewait

  Service resetoutside

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 set pfs

  Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

  life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

  Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

  Crypto-map dynamic dynmap 10 the value reverse-road

  card crypto mymap 1 match address outside_1_cryptomap

  card crypto mymap 1 set counterpart x.x.x.x

  card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

  card crypto mymap 86400 seconds, 1 lifetime of security association set

  map mymap 1 set security-association life crypto kilobytes 4608000

  map mymap 100-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  Crypto isakmp nat-traversal 30

  Crypto ikev1 allow outside

  IKEv1 crypto ipsec-over-tcp port 10000

  IKEv1 crypto policy 5

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 50

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  preshared authentication

  aes-256 encryption

  sha hash

  Group 1

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  Console timeout 0

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal BACKDOORVPN group policy

  BACKDOORVPN group policy attributes

  value of VPN-filter 11

  Ikev1 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelall

  BH.UK value by default-field

  type tunnel-group BACKDOORVPN remote access

  attributes global-tunnel-group BACKDOORVPN

  address pool Admin_Pool

  Group Policy - by default-BACKDOORVPN

  IPSec-attributes tunnel-group BACKDOORVPN

  IKEv1 pre-shared-key *.

  tunnel-group x.x.x.x type ipsec-l2l

  tunnel-group ipsec-attributes x.x.x.x

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  Excellent.

  Evaluate the useful ticket.

  Thank you

  Rizwan James