2.4 GHz Wireless and the problem of USB 3.0 with WRT1900ACS

Hi people

I guess I discovered a new "buggy" feature on my new ultra buggy router.

When I plug my WD mybook external hard drive usb 3.0 on the slot usb 3.0 on the Router 2.4 GHz and 2.4 GHz-comments off immediately. When I unplung the hard drive the 2.4 GHz re - started working properly, but after 3 times this operation, I have to restart my router with the cause of usb 3.0 unplugged the 2.4 GHz band stops to work control. (also tried with different readers)

On the 2.0/sATA port everything works fine, but I bought this router for sharing an external hard drive connected to the router quick installation network data (and on this side, this router is amazing > 100 MB/sec in reading from the hard drive to the usb 3.0 port).

This happens with the firmwares both 1.0.0.169041 and 1.0.0.168229.

I also tried to put all possible combinations in the settings Wireless 2.4 GHz.

All wired connections work properly since I bought it.

If I can't solve this problem in 1 week I will change this router, bought on amazon, with an ASUS or a Netgear, may be less effective on the side of drive hard usb 3.0, but probably more stable than this one.

It seems to me that Belkin doesn't care for anything about its customers, they do not work hard to solve the problems on these router, otherwise there is no other router but WRT1900AC v1 with a stable firmware. Instead, the company retains to launch the new hw updates each year. Belkin will never reach the success of the WRT54G in following this path.

The speed of USB3.0 data transfer causes intereferences with the frequency of 2.4 GHz WLAN.

Make sure that you use a USB 3.0 cable tank of high quality when connecting any device to the USB 3.0 port.

Tags: Linksys Routers

Similar Questions

  • My Firefox exit and gives a "not responding" message once I used Google Mail. I tried to boot into "safe" mode and the problem persists.

    I have a question where Firefox wont ' quit and give a message "not responding" after I've been using Google Mail. It works fine when I'm not using this program. I tried Safe Mode and the problem still happens when I go on Google Mail, so it is not connected with modules, extensions, etc.

    Hello

    The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.

    Note: This will make you lose all the Extensions and preferences.

    • Sites Web open is not recorded in less than 25 versions of Firefox.

    To reset Firefox, perform the following steps:

    1. Go to Firefox > help > troubleshooting information.
    2. Click on the button 'Reset Firefox'.
    3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
    4. Firefox opens with all the default settings applied.

    Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

    This solve your problems? Please report to us!

    Thank you.

  • I bought my iPhone 5 s by T-Mobile and 2 months left to purchase. My phone don't get re will not charge. Support Apple says this isn't the phone and replace the cable. This was done and the problem remains. Anyone who has experience of this pro

    I bought my iPhone 5 s by T-Mobile and have 2 months left on the purchase. My phone no longer accepts a new presentation. Apple support ran a diagnostic and said it isn't the phone and that I should replace the cable. This was done and the problem remains. Everyone has to experience this problem? And, if so, what was the problem?

    He likely is the phone, but you do Apple physically inspect it. Send it or take it to the Genius Bar. You can do one or the other of http://getsupport.apple.com.

  • How to install this update and resolve problems of USB and the touchpad?

    I Equium M50 (59th) and am bitten by an update that pulled my touchpad and keyboard. I did the new installation of XP Home and have all updated drivers and everything goes well. The last update, what I can't understand is for
    Ana _2005_10_24_V1.2 driver is for, Standard Open HCD USB Host Controller... X 2 .........

    The update addresses all kinds of questions like I'm having and is an update recommended driver detective, I use offten.

    The problem is that it says uninstall the drivers for the i have installed already and when I do it it hits off my USB mouse me leaving no able to install the new. When I reboot it installs those I don't want not reinstalled.

    This is the read me, off the coast of the new update and really I don't understand to underdstand what to do... .so here it is?
    Driver revision history:
    Twinhan VP704A Driver Release Notes
    -------------------------------------------------------------------------------
    Note:
    1. in the event that the system hangs when running with VP704A, please install ULI
    Host USB 2.0 in \ULiUSB20Driver driver

    2. for XP/SP1, please update with the patch in

    3. in XP/SP1, update driver will crash the system, while the new facility is ok.
    The trick to update driver XP/SP1 is illustrated in the following steps,
    a. uninstall the driver
    b. disconnect and reconnect the USB device
    c. install the driver
    4 to support the controller remotely, please launch Agent.exe in \Agent.
    Further details at \Agent\Readme.txt

    Known issues:
    1 multi-instance is not supported
    2 remote wakeup is not supported
    3. strong use of the processor from analog video/audio capture
    4. bad Signal using color YUY2 format IST
    5 AV sync if audio captured the wrong filter.
    (Difficulty: use the filter "USB Audio Device" in the flow WDM capture device)
    6. noise with analog TV and FM Radio
    (Difficulty: use the filter "USB Audio Device" in the flow WDM capture device)

    Driver revision history:
    -------------------------------------------------------------------------------
    2005-10-24, version: 1.0.2.8
    Bugs fixed and new features:
    1 is not correctly configured.
    -------------------------------------------------------------------------------
    2005-10-21, version: 1.0.2.7
    Bugs fixed and new features:
    1. the firmware version read FLASH OK!
    -------------------------------------------------------------------------------
    2005-10-14, version: 1.0.2.6
    Bugs fixed and new features:
    1.MUtil - access driver empty part lower part of screen when IST!
    2.MUtil - access HCT pilot check fix crash!
    -------------------------------------------------------------------------------
    2005-10-07, version: 1.0.2.5
    Bugs fixed and new features:
    1 tuner turns off when S-Video, Composite.
    -------------------------------------------------------------------------------
    30/09/2005, version: 1.0.2.4
    Bugs fixed and new features:
    1.agent.exe update for repeat bug!
    2.TI5150 sign up to fix video Format!
    -------------------------------------------------------------------------------
    2005-09-29, version: 1.0.2.3
    Bugs fixed and new features:
    1.A pilot of the trial build for multiple access medium. (in the folder "\Multi-Access")
    Note: The filter 'Audio device USB' provided by the system does not support mutil-access.
    2 reset TI5150 when a new frequency is defined
    -------------------------------------------------------------------------------
    2005-09-27, version: 1.0.2.2
    Bugs fixed and new features:
    1. difficulty I2C unstable access on some devices.
    -------------------------------------------------------------------------------
    2005-09-23, version: 1.0.2.1
    Bugs fixed and new features:
    1. analog TV becomes sometimes darker.
    -------------------------------------------------------------------------------
    15/09/2005, version: 1.0.2.0
    Bugs fixed and new features:
    1. difficulty of installation INF for Windows 2000.
    2 FM scan radio policy changed!
    -------------------------------------------------------------------------------
    13/09/2005, version: 1.0.1.9
    Bugs fixed and new features:
    1 USB string serial number not visible with USBView, updated firmware required.
    2. political analysis of FM radio, return of release if PLLOffset > = 9 x 12. 5 kHz
    -------------------------------------------------------------------------------
    13/09/2005, version: 1.0.1.8
    Bugs fixed and new features:
    1. after the passage between AV/D/A several times, video display becomes dark in THDTV 2.61
    -------------------------------------------------------------------------------
    12/09/2005, version: 1.0.1.7
    Bugs fixed and new features:
    1. improve the performance of check channel lock status
    2 pinnacle INF Fix.
    -------------------------------------------------------------------------------
    2005-09-09, version: 1.0.1.6
    Bugs fixed and new features:
    1. Add an audio initialization function.
    -------------------------------------------------------------------------------
    2005-08-31, version: 1.0.1.5
    Bugs fixed and new features:
    1 separation of PAL and NTSC resolution mode.
    -------------------------------------------------------------------------------
    2005-08-30, version: 1.0.1.4
    Bugs fixed and new features:
    1.AvgTimePerFrame.
    2 frame drop.
    3 pinnacle inf file HCT chkinf fail.
    -------------------------------------------------------------------------------
    2005-08-22, version: version 1.0.1.3
    Bugs fixed and new features:
    1. add remote control interface in digital source filter.
    2.A new remote test tool that contains of the source code in \Test_RC.
    -------------------------------------------------------------------------------
    2005-08-16, version: 1.0.1.2
    Bugs fixed and new features:
    1. Pinnacel & Twinhan driver & file reorg.
    2.VP704A_BDA_Test tool, add a test to the system code.
    3. set the standard infrared protocol of "IRSTANDARD", "IRSYSCODECHECK1" registry keys in the INF file.
    4 firmware update
    -------------------------------------------------------------------------------
    2005-08-15, version: 1.0.1.1
    Bugs fixed and new features:
    1 serial number feature is lost when the audio volume of the TV control
    2.RC6A support CIR
    (This firmware uses GPIO3 (M9207 pin 80) to decode the RC6 Protocol.
    The material must be reworked to connect the M9207 80 pin to the CIR module and the actual
    EEPROM must be flashed with \Firmware\M9207.bin)
    3 Serieal, MAC address and name of device OEM taken in charge.
    Please see for more details on the \Firmware\readme.txt.
    4 Ioclt example source code included.
    -------------------------------------------------------------------------------
    08/08/2005, version: 1.0.0.10
    Bugs fixed and new features:
    1. increase audio volume analog TV.
    -------------------------------------------------------------------------------
    04/08/2005, version: 1.0.0.9
    Bugs fixed and new features:
    1. analog TV Video mode failed.
    -------------------------------------------------------------------------------
    2005-08-03, version: 1.0.0.8
    Bugs fixed and new features:
    1.off - centerf frequency scan + / 125Khz
    2 difficulty program a copy scanned in MCE.
    -------------------------------------------------------------------------------
    02/08/2005, version: 1.0.0.7
    Bugs fixed and new features:
    1.THBDAConsole.exe 'ulFixedBW', 'ulDisableOffFreqScan', 'ulMCEFreqTranslate' bug
    -------------------------------------------------------------------------------
    2005-07-28, version: 1.0.0.6
    Bugs fixed and new features:
    1.THBDAConsole.exe 'ulFixedBW', 'ulDisableOffFreqScan', 'ulMCEFreqTranslate' support
    2. improve the stability of I2C communication.
    3 unify signaling resistance & quality as a THBda ioctl interface.
    4 capture filter lock state control.
    -------------------------------------------------------------------------------
    2005-07-28, version: 1.0.0.5
    Bugs fixed and new features:
    1. the same strength & quality signals as VP7046.
    2 debug build pilot
    -------------------------------------------------------------------------------
    2005-07-21, version: 1.0.0.4
    Bugs fixed and new features:
    1. put the INF update.
    -------------------------------------------------------------------------------
    2005-07-20, version: 1.0.0.3
    Bugs fixed and new features:
    1 improve performance in PCM4
    2 passage of the analog TV Mode to FM Mode failure
    -------------------------------------------------------------------------------
    2005-07-04, version: 1.0.0.2
    Bugs fixed and new features:
    1. production tool FM test OK!
    --------------------------------------------

    And here is the Readme file from the other file in the update?

    ************************************************** ************************************************
    ULi PCI to USB Enhanced Host Controller Driver V1.72 for Windows 98 SE, Windows ME, Windows 2000 and Windows XP
    ************************************************** ************************************************

    ----------------
    INTRODUCTION
    ----------------

    This driver supports the host EHCI ULi controller under Windows 98 SE, Windows ME, Windows 2000
    and Windows XP.

    -------------------------
    CONTENTS OF THIS DOCUMENT
    -------------------------

    1. installation instructions
    2. uninstall instructions

    ----------------------------
    1. installation instructions
    ----------------------------

    (Windows 98SE & Windows ME)
    ULi USB 2.0 Controller has strapped on the system
    1. install the driver USB 2.0 ULi
    -Run the Setup program.
    -This program will copy the driver files in your Windows system, and then restart your computer.
    2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
    Host Controller"and install the driver.

    B.If any ULi USB 2.0 on the system controller
    1. install the driver USB 2.0 ULi
    -Run the Setup program.
    -This program will copy the driver files to your Windows system, then turn off your computer.
    -Fix the ULi USB 2.0 computer controller card and restart your computer.
    2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
    Host Controller"and install the driver.

    (Windows 2000)
    ULi USB 2.0 Controller has strapped on the system
    1. install the driver USB 2.0 ULi
    -Run the Setup program.
    -This program will install and load the driver and you do not have to restart the
    computer.
    B.If any ULi USB 2.0 on the system controller
    1. install the driver USB 2.0 ULi
    -Run the Setup program.
    -This program will copy the driver in your Windows system files, before turning itself off
    your computer.
    -Fix the ULi USB 2.0 computer controller card and restart your computer.
    2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
    Host Controller"and install the driver.

    (Windows XP)
    ULi USB 2.0 Controller has strapped on the system
    1. install the driver USB 2.0 ULi
    -Run the Setup program.
    -Click "NEXT".
    -This program will install and load the driver and you do not have to restart the
    computer.
    -Once install the driver ULi USB 2.0 successfully. System will detect "USB 2.0 Root '.
    Hub. " Please select "Install the software automatically (recommended)" and then
    Click 'Next' to continue the installation.
    -This program will install and load the driver and you do not have to restart the
    computer.
    B.If any ULi USB 2.0 on the system controller
    1. install the driver USB 2.0 ULi
    -Run the Setup program.
    -This program will copy the driver in your Windows system files, before turning itself off
    your computer.
    -Fix the ULi USB 2.0 computer controller card and restart your computer.
    2. after the system restarts, Windows will detect the new hardware 'ULi PCI to USB Enhanced
    Host Controller', proceed with the installation.
    -Once install the driver ULi USB 2.0 successfully. System will detect "USB 2.0 Root '.
    Hub. " Please select "Install the software automatically (recommended)" and then
    Click 'Next' to continue the installation.

    Notice:
    If you can not configure driver successfully. Please restart your system, then follow
    steps to reinstall driver above.

    ------------------------------
    2. uninstall instructions
    ------------------------------

    1. open the "Control Panel" folder.
    2 call the "Add/Remove Programs" icon
    3 choose the "ULi USB2.0 Driver" section.
    4. click on the "add/delete" button to remove drivers.

    -----------------------------------
    Change list:
    -----------------------------------
    1.74
    1 fix this multi-interface keyboard may not be detected on the USB 2.0 hub.
    2. support all USB2.0 Host Controller.
    1.73
    1 problem on Win98SE, blue screen when you unplug a USB 2.0 Scanner after scanning image.
    2 solve problem on Win98SE, blue screen when you unplug a few Scanner USB 2.0 USB 2.0 Hub after scanning image.
    3 fix on Win98SE, blue screen when copying of files through the hub of UH-204 SUNBOX.
    4 solve problem as wirless lan will disconect when the plug in usb device.

    1.72
    1 fix that system crash when HD USB copy large files.

    1.71
    1. improve the management of power in Win98 / Me.

    1.70
    1. improve the devcie detection function.

    1.62
    1 solve the problem that can not operate a USB HUB USB 2.0 disk when the system resume inactive.

    1.61
    1 solve the problem that some device under USB 2.0 HUB is not found if resumes suspension system.

    1.60
    1. in support of functions power management when a HUB with the USB plug in device
    a root HUB.

    1.57
    1. Fix USB with USB 2.0 HUB floppy cannot detect problem.
    2. fix audio problem that can not display smooth when peripheral USB connect to the system.
    3. fix system cannot detect DVICE USB when the USB device attached to the system in
    suspend mode.
    4 fix when root USB HUB have a full load, USB HD sometimes
    failure of the transaction.

    1.56
    1 fix that device of DVD decoder cannot display correctly.

    1.55
    1. fix OTI USB 2.0 drive hand cannot detect question.
    2. attach the USB mouse cannot be used after the resumption of hanging.

    1.54
    1. to improve the safety of the driver.

    1.53
    1. transfer bulk fix may stop if the USB device is connected to the USB 2.0 hub
    2 difficulty USB 2.0 mass storage device cannot access after the release of the standby mode if there is an another USB 1.1 existing device

    1.52
    1 correct fault of system pages when accessing the storage of mass Win98SE or scandisk device failure when selecting
    automatically fix file system errors
    2. fix system may hang on in Win98SE / ME if USB 2.0 cardbus card is plugged

    v.1.51
    1. to improve the compatibility of USB 2.0 card reader.
    2. fix USB IDE devices are not accessible after the release of the standby/hibernation mode.

    v1.50
    1. improve the transfer block

    v1.48
    1. difficulty of installation of the USB 2.0 LAN driver hangs up
    2. attach a USB 1.1 card reader cannot be identified when plugged into the USB 2.0 hub
    3. fix some laptops starting hanging Win98SE

    v1.47
    1. improve the performance of bulk transfer.
    2. fix the failure of USB 2.0 Preview in bulk webcam.

    v1.46
    1. support USB 2.0 and 1.1 devices isochronous
    2. fix system hang up when restarting system if the USB 2.0 host controller is disabled in Win9X / ME
    3. fix system hang up when you uninstall the driver if there is USB 2.0 connected under Win2K/XP devices
    4. improve the capacity of the device detection in Win9X / ME

    v1.45
    1. fix system hang up when the mode standby ACPI.
    2. attach the mouse sometimes does not disappear when it is unplugged.
    3. fix the failure of detection of composite devices Win9X and improve device composite Win2K/XP

    v1.44
    1. composite crutch
    2 improve the detection of devices

    v1.43
    1 improve the failure rate of transfer IDE read/write with USB 2.0 to IDE bridge on the platform of PC card
    2 difficulty at high peripheral speed detected as full-speed device
    3. fix some problem of failure detection USB mouses
    4. fix some problem USB 2.0 Hub failure detection
    5 difficulty Win98SE crashing if ULi EHCI 1.42 is installed

    v1.42
    1. fix PC Card eject hang up in Win98 / ME
    2 difficulty of interruption/resumption hang up in Win98
    3 sometimes solve USB 1.1 device cannot be detected if OS starts with USB 2.0 and 1.1 devices plugged
    4. fix some failure detection of PC Card USB 1.1 devices

    v1.41
    1. Add new feature that system can install the driver ahead of the device is plugged in.
    2. fix PCMCIA OHCI controller resources affect problem on Windos ME.

    v1.40
    1. support Win9X/ME / 2 K/XP with ULi USB 2.0 driver.
    2 fix PCMCIA EHCI controller detection device USB 2.0 problem in Win9X / me.

    v1.32
    1. Fix problem that pilot cannot detect the Microsoft driver in Windows XP
    If the path of the OS is not c:\windows.
    2. Fix problem that pilot cannot detect the USB 2.0 controller device in a system.

    v1.31
    1. Fix problem that driver cannot install on Windows 2000.

    v1.30
    1 fix than Win9X / shows ME no USB 2.0 hub.
    2 solve the problem that hang up when the second entry in Win9X S1 with HID device connected.
    3 Fix problem that sometimes when you click on "search the hardware changes.
    for PNP ULi USB2.0, controller, the system will inform you the usbehci.sys
    file is not found.
    4. Fix problem that v1.20 can't find no EHCI controller to install the driver for after different
    verison of ULi EHCI controllers devices are connected and disconnected.
    5 install the driver support for several features of controller EHCI ULi existing on
    system at the same time.
    6. determine Win2K/XP shows hub USB root for USB 2.0 hub.

    v1.20
    1. support ULi USB 2.0 for Windows 98SE/ME/2000/XP host controller driver.

    ULi Coporation. (ULi) web sites:
    http://www.Uli.com.tw/ (Taiwan)

    CAN SOMEONE TREAT ME LIKE A CHILD OF TWO YEARS AND GIVE SOME ADVICE AS TO HOW TO OBTAIN THIS UPDATE.

    I'D VERY GRATEFULL AND KIND OF THINK IT would BE BENEFICIAL to a LOT MORE than PEOPLE LIKE I SEE a LOT OF XP AND PROBLEMS OF THE KIND THIS UPDATE IS SUPPOSE to FIX.

    It is said above 2 relevant and 1 right ANSWER available...

    I'm new here, so anyone could direct me to these answers?

  • Hello. There is a problem on the IPhone s 5 - after reset, the display flashes on the sides for 10 minutes, then the flashing stops. And the problem does not appear again until they do not use a Hard Reset (Power Home). The phone is new (5 days). It's a m

    Hello. There is a problem on the IPhone s 5 - after reset, the display flashes on the sides for 10 minutes, then the flashing stops. And the problem does not appear again until they do not use a Hard Reset (Power + Home).

    The phone is new (5 days). It's a wedding?

    If you encounter this flicker, then the next troubleshooting step is to restore from a backup. If the behavior persists after the restore, then the last step is the factory restore. If after the factory restore and adding no additional content, you see always this problem, then you must make an appointment at the Genius Bar to the nearest Apple store or service provider authorized Apple to have the material examined. If the behavior goes after the factory restore, then sync again your content manually, without using the backup. It seems to me it's corrupted content in the backup.

    Restore your device from an iCloud or iTunes backup - Apple Support

    Use iTunes to restore your iPhone, iPad or iPod settings - Apple Support

  • The procedure of procurement of the game Clash of Clans first two payments $9.99 $4.44 and the second did not gems continued with the developer of the game and they told me to resolve this ongoing problem with Apple's iTunes... help me solve

    The procedure of procurement of the game Clash of Clans first two payments $9.99 $4.44 and the second did not gems continued with the developer of the game and they told me to solve this problem continue with Apple iTunes... help solve me this problem and the compensatory jewelry

    Double-see your message, my first response to this topic tells you how to contact iTunes Support (we are fellow users): Re: the procurement process of the Clash game Clans the amount was deducted from the iTunes account and do not have t...

  • iPhone 5 activate without sim card and the problem is average insert a SIM card when sim carn as invalid sim

    iPhone 5 activate without sim card and the problem is average insert a SIM card when sim carn as invalid sim

    Fast pleas tell me

  • I'm having the problem of local connection on my Dell PC with Vista. ISP is Verizon FIOS. FiOS representative told me to disable Ipv6 and the problem stops. Is this correct?

    I'm having the problem of local connection on my Dell PC with Vista. ISP is Verizon FIOS. FiOS representative told me to disable Ipv6 and the problem stops. Is this correct?

    original title: local area connection problem

    Hello

    1. What is the exact problem you are facing with local connection?

    2. how many computers have you plugged into the network?

    Please provide the information of network event logs to help you best.

    Click on the link below.

    http://Windows.Microsoft.com/en-us/Windows-Vista/using-Windows-Network-Diagnostics-event-logs-to-solve-network-problems

    In the meantime, run the troubleshooter mentioned in the link below.

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  • Hello world! I'm french so if I speak wrong forgive me. For my work I need to buy adobe acrobat and the problem is I'll maybe change my computer, but not now. If I have installed adobe acrobat in my computer would it be possible to install the s

    Hello world! I'm french so if I speak wrong forgive me. For my work I need to buy adobe acrobat and the problem is I'll maybe change my computer, but not now. If I have installed adobe acrobat in my computer would it be possible to install the software in my future computer without purchasing another license that is to say with the same license that I bought?

    Yes, you can reinstall it on other machines, if you wish, without having to buy new.  A license allows for activating facilities on two machines and if necessary, you can turn off a machine in order to allow the activation of another.

  • Hello good I would like to cancel the annual plan of adobe audition, because I had problems with the software and the Bank, if I can help with this please.

    Hello good I would like to cancel the annual plan of adobe audition,

    As I have had problems with the software and the Bank, if I can help with that please.

    Please contact customer support for cancellation & refund of the next purchase. Contact the customer service

    Creative single-app cloud membership for Adobe Audition (one year) Subscription Office March 11, 2015

    In the case of any questions, please let us know, I can certainly go for you.

    Concerning

    Baudier

  • Hello I am a student and I have a problem with the tool Selection (V). When I opened the file AI CC with CS6 selection tool doesn't allow me to change the selection. What can I do? (I have reinstall AI CC and the problem persists)

    Hello I am a student and I have a problem with the tool Selection (V). When I opened the file AI CC with CS6 selection tool doesn't allow me to change the selection. What can I do? (I have reinstall AI CC and the problem persists)

    Ivan,

    If it's on the rectangular objects, you may have encountered the bug Rectangle Live which is limited to the MAC versions from 10.7 and 10.8, but not of 10.9 (Mavericks) or 10.10 (Yosemite). If all goes well, the bug will be fixed soon.

    Thus, a switch for the Mavericks or Yosemite with a reinstall might be the way to solve it here and now.

    To get around it, in each case, it is possible to develop direct Rectangles to get the normal old shaped rectangles or Pathfinder > unit, or use the scale tool or the free transform tool.

    A more permanent way round that is to create normal old shaped rectangles, after running the free script created by Pawel, see this thread with download link:

    https://forums.Adobe.com/thread/1587587

  • If I purchased this computer about 4 months ago I can support windows 7 free? and the 64-bit system will work with windows 7

    If I purchased this computer about 4 months ago I can support windows 7 free? and the 64-bit system will work with windows 7

    This is the Forum for Windows Update.

    How does the Windows 7 upgrade Option?

    The Windows 7 upgrade Option is available through participating PC manufacturers on some PC and Microsoft on any purchase of packaged product Windows Vista. The Windows 7 upgrade Option applies to Windows Vista Home Premium, Business and Ultimate editions. Your upgrade to Windows 7 will be the comparable version: so you will get either Windows 7 Home Premium, Windows 7 Professional (upgrade to Windows Vista Business) or Windows 7 Ultimate, respectively. The Windows 7 upgrade Option program works on June 26, 2009 through January 31, 2010.

    http://www.Microsoft.com/Windows/buy/offers/upgrade-option.aspx

    Above Microsoft link has info for the Options to upgrade Windows 7 from participating computer manufacturers.

    Read the info here to see if you qualify.

    http://www.Microsoft.com/Windows/buy/offers/upgrade-FAQ-option.aspx

    FAQ about the upgrade is at the link above.

    http://www.Microsoft.com/Windows/Windows-7/get/Upgrade-Advisor.aspx

    Windows 7 Upgrade Advisor.

    http://TechNet.Microsoft.com/en-us/library/dd772579 (WS.10) .aspx

    Railways upgrade to Windows 7 at the link above.

    For any other question of Windows 7:

    http://social.answers.Microsoft.com/forums/en-us/category/Windows7

    Link above is Windows 7 forum for questions on windows 7.

    Windows 7 questions should be directed to the it.

    You are in the Vista Forums.

    See you soon.

    Mick Murphy - Microsoft partner

  • I made a new music video for a song, and the music is not in time with the film, how I put in time?

    I made a new music video for a song, and the music is not in time with the film, how I put in time?
    Oh and I'm using WIndows Movie Maker. One.

    Please repost in Windows Live Solution Center.
    Forum on Windows Live Movie maker:
    http://windowslivehelp.com/forums.aspx?ProductID=5

  • MP3 corruption during the copy to USB or playing with MP11

    Bought a cheap good car 16g off ebay.  No brand name.  To use in the car to listen to music (we have a new sienna with USB socket)
     
    Has started moving the MP3s to it, a bunch of files
     
    Found that at a given time, a file will not play with media player.  Therefore, no new file (copied to USB) after bad, would play.  Does any kind of codec error.  If I delete bad and try to copy it, he would not play.
     
    So I format USB and start over.  It happens again, with different files.  I do this a few times
     
    Finally, I find that media player is changing the file to be unplayable.  I tried to open one with media player classic and it works, but then, open the file with the current media player, I get the error, and it's more playable by classic.  After the file fails, the media info, artist, album, ect, is gone, but the name and size remain.  Size looks normal, but the image of the album no longer appears on the file manager.
     
    After testing more far, I see some files do not survive to the copy.  Others survive the copy, but media player is their in.  Error always the same on these files.  I can copy back them and replace, and sometimes they are OK, then other times they need a another copy and replace.  In all cases, the album art has disappeared.
     
    I found that if I delete one of these files, the next time I copy, it seems good, but is damaged if I play with media player.  Media player classic it plays very well and does not alter it.
     
    So, in summary, I'm sure only a few things
     
    Symptoms of a bad file is that it won't play in anything whatsoever, says he needs of codec, and I have more music as album info and others.  Such a file can occur after copying on USB key, or the first time, it is played with the current media player (media player helps says it's common when I ask for update).
     
    Some files do not copy right.  I can copy back them and they're right.  However, sometimes they lack the album image in the file manager.  No correlation with the existence of this image, and if the media player will be trash.
     
    Some of the files when they are played with media player go corrupt and will play is classic.  I have copy and I can play the recopied with media player classic, but try media player and it will be corrupted again.  The original copy of the copied file will play well with media player out of the hard drive, but will go corrupt if played off of USB, however, if copied from the USB to the desktop, it will now play with media player, but the album cover will look smaller than the original hard disk.
     
    Currently, the problem is only with files that are on the USB drive.
     
    A lot of hiking here, but you have an idea of what is going on?
     
    I'm afraid that this media player will decide to begin to destroy ALL my mp3s.  I went Classic Media Player to be the default for MP3 player, but you still wonder what WTF.
     
    Or is it a kind of USB problem?  I did a full and several quick formats of USB.
     
    Any ideas?

    Hidyrwolf,

    It seems that there is a problem with the USB drive as the file copied from the USB to the computer plays very well and the problem occurs with files that reside on the disk.

    To check if the problem caused by the USB, I suggest that you plug the USB on the other computer and check if the problem persists.

    Alternatively, you can add the missing information to the media library of Windows media player.

    Add or edit media information in Windows Media Player

    http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-edit-media-information-in-Windows-Media-Player

    Where is my album art?

    http://Windows.Microsoft.com/en-us/Windows-Vista/wheres-my-album-art-fixing-song-titles-artist-names-and-more-in-Windows-Media-Player

     

    You can also try to update the Codecs on the computer and check if the problem persists.

    Codecs: Frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows-Vista/codecs-frequently-asked-questions

    I hope this helps!

    Halima S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Messages of the Sierra and the problems of continuity iMessage

    I took these communities to try to resolve a problem which, for me, is as old as the first day iMessage became available for Mac.

    I can't emphasize how incredibly boring, it is completely out of sync how both are. The problems are always the same:

    (1) never are conversations in the issue of order/same on both devices. For example, for a conversation that has been exploited to iMessage on my iPhone, when I open my Mac, it appears in the notifications, like new. All the answers are there.

    (2) a conversation that has been deleted from the iPhone suddenly appears on the opening on my Mac... seriously?

    (3) the conversations that are deleted on my iPhone does not disappear in the Messages and vice versa.

    To sum it all, pretty much the case is that both apps, while they expected to work simultaneously with fluidity to do what they want when they want.

    This has been a problem since iMessage became available on Mac OS for the first time (think it was Mavericks). I've been waiting for Apple to fix this with each software update to make OSX or iOS. But guess what...?

    My Mac running OS Sierra and my iPhone 6 s more running iOS 10.0.1. Everything that could be activated in so that they can work together has been activated and triple checked. I would really like to know if anyone has a way to fix this or if there is other people are having the same problem.

    Hello

    An excellent explanation of exactly how iMessages works on iPhone and Mac.

    It does the same thing, if you add in an iPad or and iPod Touch.

    iMessages are pushed, the Treaty is called, for devices that have been associated with (by adding the Apple ID on an iPhone).

    This means that it is not as Mail where are read from the server and in the case of a POP account you can choose to let the "message" on the server if other devices can read.

    IMAP accounts will be synchronized as you say but POP will be more like the Messages app with iMessages.

    The iMessages which is addressed to you are marked by the number of devices is in the opportunity to see it.

    He pushes the devices until they respond (Accept) once this device has accepted it is removed from signage and only devices that did not have a chance on seeing.

    There is a time limit on how long the iMessages is pushed to a device (such that being away from your Mac turned off everything on vacation or phone that died or was out of range of the carrier)

    Once the device have the iMessages it is removed from the server.

    A simpler view is that the iMessages is "copied" and sent to each device and that each device can not see the other "versions" and that each "copy" is deleted from the server that happens on the device.

    The news to "read" your comments, you might see comes that of the device, it was intended to (i.e. addressing a number only the iPhone to another end may, so together, to send the reply 'read').

    Same thing with sent.  This is why you get a response, when he showed even "Delivered" as someone can answer from a connected device.

    This means that the 'Sync' is really only show on all devices and nothing do you on one device will be the effect of the other.

    It is not broken, even if this isn't what you think that told you about the device.

    You can tell them http://www.apple.com/feedback/messages.html

    20:31 Saturday; October 1, 2016

     iMac 2.5 Ghz i5 2011 (El Capitan)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro (Snow Leopard 10.6.8) 2 GB
     Mac OS X (10.6.8).
     iPhone and iPad (2)

Maybe you are looking for