2 Ihave rundll to appear on my screen when I start saying error loading I need them to be installed or I can remove them thanks

2 rundll Ihave to appear on my screen when I start my pc, they declare that they are error loading c\windows\system32\prwleprn.dll. and c\windows\system32------nsiad.dll - (the specified module is not found.)   could you help please because I do not know if I need it or not if I could you tell me how I can install them, but if I don't need them could you tell me how I can remove them thanks

PML instructions are precise and concise.

My instructions for this issue are similar but more verbose - perhaps they will help you get your system fixed to the top (just read them first, then apply them).

A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.

Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry. There is no cancellation or exit without saving the option in regedit.
Here is a link to a popular registry backup tool:
You can also use the Autoruns to find the element of start remains little matter where he's hiding.

Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information.  You are really interested only a few sections.
The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
Scroll through the list and look for a boot entry associated files in the error message.
If you can't find on the connection tab, look in any tab.
You can also click file, search to search for logon, or any tab for all or part of the name of the element.
Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can simply disable, restart and if the problem is resolved and then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
Given that you had or have an infection, followed with this:
Perform scans for malware, and then fix any problems:
Download, install, update and do a full scan with these free malware detection programs:
Malwarebytes (MMFA): http://malwarebytes.org/
SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
They can be uninstalled later if you wish.
Restart your computer and solve the outstanding issues.

Tags: Windows

Similar Questions

  • How can I prevent the WKUfind.exe that appear on my screen why I start my pc

    How can I prevent the WKUfind.exe appearing on the screen when I miss my PC?

    Hello

    1. what version of Windows are you using?

    2 have had any changes made to your computer before this problem?

    Perform the following methods and check if it helps.

    Method 1:

    I recommend placing the computer in a clean boot and then check if the problem persists or not.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

    Method 2:

    You can also scan your computer the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

    The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

    Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

    Hope this information is useful.

  • Volume control does not appear on the screen when I try to activate it. This has never been a problem until now. How can I get this working again?

    The volume control is located at the bottom right of my sidebar it me has not given any problems so far. Now, he just will not appear on the screen when I try to call. This has never been a problem before. I really did something to screw things up (again!) today. This is the first time I had this problem.

    Next time please indicate what opersting system you first use before describe you your problem.

    You can start by doing a system restore. Choose a date on which your Volume icon in the taskbar.
    http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

    If for some reason it does not restore the Volume icon, then...

    For Vista, use this tutorial:

    http://www.Vistax64.com/tutorials/106787-notification-area-system-icons.html

    You can try a method first. If the Volume box is grayed out (is usually), go to method 3.

    2. for the Volume icon

    To activate the Volume - icon Enable_Volume.reg< click="" to="">
    Then, follow the instructions from #5 to #9.
    Make sure that you restart the computer to complete the process.

    For Windows 7, use this tutorial:
    http://www.SevenForums.com/tutorials/19085-system-icons-enable-disable.html

    Go directly to the Option two

    9. to activate the Volume icon

    (A) click on the download button below to download the file below.

    Enable_Volume_Notification_Icon.reg

    then follow the instructions from #11 to #15.

    Make sure that you restart the computer to complete the process.

  • I get an error code of 1311 with Windows Installer to appear on the screen when I try to navigate.

    the Windows Installer

    Presentation of adobe acrobat 7.0

    Error 1311. Word of source file found

    c:\Program files \adobe\acrobat 7.0\ configuration files\acropro\enu\data 1.cab. Check that the file exists and that you can access.

    Original title: Error 1311, windows installer appears on the screen, when I Browse.

    Hi-mountain dew,

    Thanks for posting your query in the Microsoft Community. It seems that you have a problem with Windows Installer pop up on the screen while browsing. We can get this fixed number by systematically. It can be frustrating for you. But, don't worry, we're here to help.

    We start with a few questions-

    (1) do you get this pop-up when you navigate to a specific Web site?

    (2) you are trying to install Adobe Acrobat 7?

    (3) have you made changes on the computer before the show?

    I would like more information about the issue.

    Method-

    I would have you see the article from the adobe website as he talks about the Error 1311-

    Error 1311, 1335, or 2350 "... not found Source file data1.cab ' | Install Adobe products | Windows

    http://helpx.Adobe.com/Creative-Suite/KB/install-Error-1311-1335-or.html

    We know if you need help. We will be happy to help you.

    Thank you.

  • How to stop messages from Skype that suddenly appears on my screen when other people use my computer? using windows 8

    How to stop messages from Skype that suddenly appears on my screen when other people use my computer?  using windows 8, but I can't control these messages (sometimes very) distracting to appear?

    Hello

    If you are allowing others to use the computer, set up a new account for each user.  They would then not be able to display your desktop or Skype messages.

    http://Windows.Microsoft.com/en-us/Windows/create-user-account#create-user-account=Windows-8

  • Hi performer El Capitan on iMac - Illustrator CC windows do not appear on the screen when checked - what is the problem?

    Hi performer El Capitan on iMac - Illustrator CC windows do not appear on the screen when checked - what is the problem?

    Try the window > Application frame.

    May be required to be on continuously, there seems to be some kind of issue.

  • I get a black screen saying "error loading operating system".

    Dell Optiplex GX620: When I inserted a flash drive to back up a couple of new entries of Quicken, I get an unusual message and a black screen appears with another message above on the left that says "Error loading operating system".  It recharges got the same results.
    He managed the Express Test in the Partition Utilities [F12]. Then I went to Microsft.com/support and found articles on how torepair my computer from my data "Reinstallation CD Microsoft Windows XP Professional Service Pack 2" without losing. The 3 choices of the place where to repair Windows were: "-: partition1 [FAT] 31MB [24MB free];  C:partition2 [Unknown] 76246 MB [76245 MB free];   Unpartitioned space 16 MB. "I chose the c: [the computer said that the other 2 are too small.]  Finally, this message appeared: 'Partition is either too full, damaged, not formatted, or formatted with an incompatible file system.  To continue installing Windows, Setup must format this partition, C:Partition2 [Unknown] 76246 MB [76245 MB free]. All data will be lost. I left the repair.
    Hope this can help you get my computer goes withour data loss.  Thanks a lot, a lot, Joe

    Hi joesg,

    We recommend that you cross check if you have followed the steps correctly to perform the repair facility.
    See perform a repair Installation

    If the problem persists, then we you should back up data on the hard drive by connecting it to another computer and try to reinstall Windows XP.
    See How to install or upgrade to Windows XP

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • How guys do you overcome (Mac Book and iMac) screen sizes with disabilities when creating scrolling effects, can work the same on both screens when you started with the iMac?

    How guys do you overcome (Mac Book and iMac) screen sizes with disabilities when creating scrolling effects, can work the same on both screens when you started with the iMac?

    Technically, since it's the same effect with the same settings, it works on both sizes. However, you need to test both is to decide if it will appear visually correct on both screens or not. On screens more wider/taller objects can appear earlier on the screen, it is advised to test again on both screens.

    See you soon,.

    Vikas

  • When sharing my project there are some clips that show a red screen with a camera saying error. How can I solve these clips if I can share the project correctly?

    When sharing my project there are some clips that show a red screen with a camera saying error. How can I solve these clips if I can share the project correctly?

    This happens usually when the import process was not completed. If you have the original camera card - or a copy of the computer of the map - you can probably use the re-import command (on the file menu) to fix things. In addition, it is possible that the original media is imported, but this transcoding was not. If you have chosen to optimise upon import, try to select clips in the browser and transcoding to optimized.

    Russ

  • Computer stops responding with a black screen when you start Windows XP. Cannot select anything advanced startup options

    Original title: can't open Windows
    I can't open my laptop at all... block when I select anything in the mode without failure or screen black normal mode :(
    What should I do? Thank you!!!

    Hi Mihou,

    1 have. what changes you made before the question?

    2. What are the options you see in the advanced startup options?

    You can follow the methods in the article in order to solve the problem.

    Computer stops responding with a black screen when you start Windows XP
    http://support.Microsoft.com/?kbid=314503

    Azeez Nadeem - Microsoft Support [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

  • Computer stops responding with a black screen when you start Windows Vista

    Computer ceases to respond with a black screen when I run Vista, this happen right after the installation of updates. original title: computer stops responding with a black screen when you start Windows XP__

    If you think that Windows updates are loaded:

    Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

    MS - MVP - Elephant Boy computers - don't panic!

  • In my Aspire One 722 the caps lock ' notification arrested appear on my screen when I switch the key.

    In my 722 one Aspire when I toggle the button caps lock notification stopped appearing on my screen and and also stopped the audio volume indicator display when I change the volume.

    It is currently running Windows 7 and I wasn't able to find the file BTTray.exe.

    I tried to install dirver Bluetooth_Atheros_7.4.0.96_Win7x86x64 but the file is not there.

    Cannot install Bluetooth_Braodcom_6.5.0.2002_Win7x86x64 driver because the computer has no Bluetooth hardware.

    What can we do?

    Please download the Launch Manager application for your unit available at http://us.acer.com/ac/en/US/content/drivers

  • Starting Windows error loading RUNDLL C:\windows\kbjgcl.dll

    Original tile: C:\windows\kbjgcl.dll

    When starting XP Professional a pop-up is displayed during startup and States "Error loading RUNDLL C:\windows\kbjgcl.dll" and I don't know how to fix this problem. I have to press OK to remove the pop up or Cancel to continue. I also have a problem when you try to restore my system to an earlier date. The computer will go through the process, but no change it to the one of earlier date. He says that the restoration was unchanged and does not succeed. Not sure if the RUNDLL question causes me to not be able to use the restore application. I had an earlier program of malware attack my computer and I used the software to remove it, but now I have problems with this pop-up.

    Help, please.

    Hi JWH12,

    1. You receive an error message when you perform the system restore?
    2. When was the last time you be able to restore your computer using system restore?
    3. You have security software installed on the computer?

    Method 1

    There is a possibility that this computer still has some virus or malware infections.

    I suggest that you scan the computer using check and scan Microsoft security if it helps.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx 

    You can also use Microsoft Security databases to scan your computer

    http://www.Microsoft.com/security/PC-security/MSE.aspx

    Method 2

    Check if the problem persists in the safe mode and after return with the result.

    A description of the options to start in Windows XP Mode

    http://support.Microsoft.com/kb/315222

    Method 3

    If the problem persists in safe mode, then it is possible that some third-party programs installed on the computer is causing the problem.

    I suggest that you put the computer in a clean boot state and check if it helps.

    To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    See section to learn more about how to clean boot.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Reset the computer to start as usual

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

    (a) click Start, type msconfig in the search box and press ENTER.

    (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

    (c) under the general tab, click the Normal startup option, and then click OK.

    (d) when you are prompted to restart the computer, click on restart.

  • When I start the computer, I get a box entitled RUNDLL. Inside of the box, it says: "error loading c:\windows\system32\reranavu.dll." under that, it says "the specified module is not found." ___what is this? How should I do? Thank you.

    Rundll system32

    Next time put please the details of your question in the body of the message instead of the subject line.

    The reranavu.dll file is malware. Either you have uninstalled the malware program or your antivirus/antispyware program did. In all cases, a reference has been left in the boot file. You can remove the reference by managing your startup.

    Because you had a piece of malware, the chances are too high you had others. It would be a good idea to scan. I recommend to download and install MalwareBytes' anti-malware (MBAM) from http://www.malwarebytes.org . The program is free. (There is a paid version, but you don't need to buy it to remove the malware).

    Manage startup - be done only when you are sure that the computer is completely free of malware:

    (for XP) Start > run > msconfig [Enter]

    This will open the System Configuration utility. Look under the Startup tab and find the likely culprit. Uncheck the box next to its name, apply and OK out. You don't need to restart immediately, but next time you do, you will get a dialog box saying that you have used the utility. Just check the box that says in effect, "don't mind to this subject again".

    How to troubleshoot by using the Msconfig in Windows XP utility - http://support.microsoft.com/?id=310560

    The free Autoruns program is very useful for managing your Startup - http://www.microsoft.com/technet/sysinternals/default.mspx MS - MVP - Elephant Boy computers - Don ' t Panic!

  • I get a screen when you start the computer.

    Hello

    How are you?

    Recently, my system hung up and had to do a force restart. I get a screen when starting my computer with few options. I have to click ESC several times to get rid of the screen. This was not an option before. When I start my computer it used to start normally. How to get rid of the screen? Please advice.

    Photo I took of my mobile is attached.

    Windows 7

    AMD athlon

    Auto system

    Thank you

    Gershom

    Hi all

    Thank you for the support.

    I solved the problem by unplugging the cable from the hard drive inside the CPU and connected again. All is well now.

    If the system is not the start or make obstruction to the start-up stage, you can try the same thing.

    All the best.

    Thanks again John and Gerry.

    Surya Kumar

Maybe you are looking for