2 VPN SITE to SITE with ACCESS REMOTE VPN
Hello
I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration
Concerning
Thus, on the routers will be:
Cisco 2611:
LAN: 10.10.10.0/24
access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255
access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL
!
10 ipsec-isakmp crypto map clientmap
defined by peer 172.18.124.199
match address 100
!
IP local pool ippool 14.1.1.1 14.1.1.254
!
access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255
access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE
!
crypto ISAKMP client configuration group ra-customer
pool ippool
ACL 120
!
Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.
HTH,
Portu.
Tags: Cisco Security
Similar Questions
-
Cisco ASA vpn site to site with access internet, error
Hello
I have two offises, Central and removed, with the external IP addresses. They are connected to the site to site vpn, LAN works fine, then NAT is disable, but then there is no internet access, then I Internet in NAT is working well, but then there is no access to the local network.
Where would be the problem?There's config:
ASA Version 8.4(4)1
!
hostname SalSK-ASA
domain-name ld.lt
enable password xxx encrypted
passwd xxx encrypted
names
!
interface Ethernet0/0
nameif outside
security-level 0
ip address 81.X.X.X 255.255.255.0
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.204.254 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
!
ftp mode passive
clock timezone EET 2
dns server-group DefaultDNS
domain-name lietuvosdujos.lt
object network LAN
subnet 192.168.204.0 255.255.255.0
description Local Area Network
object network LD_Lanai
subnet 192.168.0.0 255.255.0.0
description LD lanai
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit ip any any
access-list vpn extended permit ip any 192.168.204.0 255.255.255.0
access-list vpn extended permit ip 192.168.204.0 255.255.255.0 any
access-list vpn extended permit ip object LD_Lanai 192.168.204.0 255.255.255.0
access-list vpn extended permit ip 192.168.204.0 255.255.255.0 object LD_Lanai
access-list outside_cryptomap_1 extended permit ip object LAN any
access-list outside extended permit ip any any
pager lines 24
logging enable
logging list VPN_events level informational class auth
logging list VPN_events level informational class vpdn
logging list VPN_events level informational class vpn
logging list VPN_events level informational class vpnc
logging list VPN_events_ID message 713120
logging list VPN_events_ID message 713167
logging list VPN_events_ID message 602303
logging list VPN_events_ID message 713228
logging list VPN_events_ID message 113012
logging list VPN_events_ID message 113015
logging list VPN_events_ID message 713184
logging list VPN_events_ID message 713119
logging list VPN_events_ID message 602304
logging monitor debugging
logging buffered debugging
logging trap VPN_events_ID
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic LAN interface inactive
access-group outside in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 81.7.77.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server ISE protocol radius
aaa-server ISE (inside) host 192.168.200.48
key *****
user-identity default-domain LOCAL
aaa authentication enable console ISE LOCAL
aaa authentication http console ISE LOCAL
aaa authentication serial console ISE LOCAL
aaa authentication ssh console ISE LOCAL
http server enable
http 0.0.0.0 0.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set tripledes esp-3des esp-sha-hmac
crypto map outside_map 1 match address outside_cryptomap_1
crypto map outside_map 1 set peer 213.X.X.X
crypto map outside_map 1 set ikev1 transform-set tripledes
crypto map outside_map interface outside
crypto isakmp identity address
crypto ikev1 enable outside
crypto ikev1 policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
management-access inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 192.168.201.200 source inside prefer
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
group-policy SalGP internal
group-policy SalGP attributes
vpn-filter value vpn
vpn-tunnel-protocol ikev1 l2tp-ipsec
username Admin password LVPpyc4ATztEAWtq encrypted privilege 15
tunnel-group 213.X.X.X type ipsec-l2l
tunnel-group 213.X.X.X general-attributes
default-group-policy SalGP
tunnel-group 213.X.X.X ipsec-attributes
ikev1 pre-shared-key *****
!
class-map global-class
match default-inspection-traffic
!
!
policy-map global-policy
class global-class
inspect dns
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect sip
inspect skinny
inspect sqlnet
inspect sunrpc
inspect tftp
inspect xdmcp
inspect icmp
class class-default
user-statistics accounting
!
service-policy global-policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]/* */
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:d8c29755eff807b1530e38b9ead9edd5
: endTwo things are here according to you needs.
First you encrypt all the traffic on the network 192.168.204.0/24... do you intend to send all traffic on that subnet via the VPN? If this isn't the case, specify the remote subnet instead of using all the crypto ACL.
object network LAN
subnet 192.168.204.0 255.255.255.0access-list outside_cryptomap_1 extended permit ip object LAN any
Second, you have not an exempt statement NAT so that encrypted traffic should not be translated. This statement would look like the following:
the object of the LAN network
192.168.204.0 subnet 255.255.255.0being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0Static NAT LAN LAN (inside, outside) destination static REMOTE - LAN LAN
--
Please do not forget to choose a good response and the rate
-
My husband has no idea of what she does on her laptop that I gave him, hes a truck driver and created our computers remotely with remote access earlier. He needs help setting up something, don't ask me what becausee it seems that I do not speak English it lol! He has no idea how find ip address or give me access (I instruct on how to give me remote access but he still could not understand)! Y at - it anyway to find my old connection (ip address) on my computer at home so I can send him an invitation to allow me on the laptop to help her. Can someone help me? I would be very appricate it! I would like to thank Krystal
My husband has no idea of what she does on her laptop that I gave him, hes a truck driver and created our computers remotely with remote access earlier. He needs help setting up something, don't ask me what becausee it seems that I do not speak English it lol! He has no idea how find ip address or give me access (I instruct on how to give me remote access but he still could not understand)! Y at - it anyway to find my old connection (ip address) on my computer at home so I can send him an invitation to allow me on the laptop to help her. Can someone help me? I would be very appricate it! I would like to thank Krystal
Try Windows Live Mesh... It works very well for remote access.
-
Synchronize with two remote servers
Is it possible to use the file manager of Dreamweaver to synchronize a local site with TWO remote servers? I want to be able to synchronize everything on my test server for the client to approve and then synchronize with the server. Only way I can do it is by changing the server in the management of sites window, thought it might be a way to do this in the File Manager window.
You can switch between the test server and the remote server in the window files expanded with the keys on top. Click the (square icon 2) expand button at the far right of the files tab, and then select the test or the remote server it...
-
problem with users to access remote vpn site to site vpn network
I did the Setup: asa 5510 configured remote access vpn. My vpn users receive asa 5510 range 192.168.50.0/24 addresses and users access my local lan 192.168.0.0/24. the second side of the local lan 192.168.0.0/24 on asa 5505, I did a vpn site-to-site with network 192.168.5.0/24.on that both sides of a site are asa 5505. inside the interface asa 5510 Elise 192.168.0.10 and inside the interface asa 5505 have address 192.168.0.17.third asa 5505 networked 192.168.5.0/24 address 192.168.5.1. I want my remote access vpn users can access resources on network 192.168.5.0/24. I create the static route on inside the asa 5510 static route 192.168.5.0 interface 255.255.255.0 192.168.0.17 and a static route on inside the asa 5505 static route 192.168.50.0 interface 255.255.255.0 192.168.0.10, but it's not working. What do I do?
execution of the configuration of my asa 5510 is
Result of the command: "show run"
: Saved
:
ASA Version 8.4(2)
!
hostname asa5510
domain-name dri.local
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.178 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.0.10 255.255.255.0
!
interface Ethernet0/2
description Mreza za virtualne masine- mail server, wsus....
nameif DMZ
security-level 50
ip address 172.16.20.1 255.255.255.0
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name dri.local
object network VPN-POOL
subnet 192.168.50.0 255.255.255.0
description VPN Client pool
object network LAN-NETWORK
subnet 192.168.0.0 255.255.255.0
description LAN Network
object network NETWORK_OBJ_192.168.0.0_24
subnet 192.168.0.0 255.255.255.0
object network 192.168.0.10
host 192.168.0.10
object service ssl
service tcp destination eq 465
object service tls
service tcp destination eq 995
object network mail_server
host 172.16.20.201
object service StartTLS
service tcp destination eq 587
object service admin_port
service tcp destination eq 444
object service ODMR
service tcp destination eq 366
object service SSL-IMAP
service tcp destination eq 993
object network remote
host 172.16.20.200
object network test
host 192.168.0.22
object network mail
host 172.16.20.200
object network DMZ
host 172.16.20.200
object network Inside_DMZ
host 192.168.0.20
object service rdp
service tcp destination eq 3389
object network DRI_PS99
host 192.168.0.54
object service microsoft_dc
service tcp destination eq 445
object service https448
service tcp destination eq 448
object network mail_server_internal
host 172.16.20.201
object service Acronis_remote
service tcp destination eq 9876
object service Acronis_25001
service tcp destination eq 25001
object service HTTP3000
service tcp destination eq 3000
object network VPNPOOL
subnet 192.168.50.0 255.255.255.0
object-group network PAT-SOURCE-NETWORKS
description Source networks for PAT
network-object 192.168.0.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object object admin_port
service-object object ssl
service-object object tls
service-object object https448
object-group service DM_INLINE_SERVICE_2
service-object object admin_port
service-object object https448
service-object object ssl
service-object object tls
service-object tcp destination eq pop3
service-object tcp destination eq smtp
object-group service DM_INLINE_SERVICE_3
service-object object admin_port
service-object object https448
service-object object ssl
service-object tcp destination eq smtp
service-object object tls
service-object object Acronis_remote
service-object tcp destination eq www
service-object object Acronis_25001
service-object object microsoft_dc
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object tcp
object-group service DM_INLINE_SERVICE_4
service-object object Acronis_25001
service-object object Acronis_remote
service-object object microsoft_dc
service-object tcp destination eq www
service-object tcp
service-object ip
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 any object mail_server
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any object mail
access-list Split_Tunnel_List extended permit ip 192.168.0.0 255.255.255.0 any
access-list outside_cryptomap extended permit ip 192.168.0.0 255.255.255.0 192.168.5.0 255.255.255.0
access-list DMZ extended permit object-group DM_INLINE_SERVICE_4 172.16.20.0 255.255.255.0 any
access-list DMZ extended permit object-group DM_INLINE_SERVICE_3 host 172.16.20.201 any
access-list DMZ extended permit object-group DM_INLINE_PROTOCOL_1 172.16.20.0 255.255.255.0 any inactive
access-list DMZ extended deny tcp any any eq smtp
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
mtu management 1500
ip local pool vpnadrese 192.168.50.1-192.168.50.100 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static LAN-NETWORK LAN-NETWORK destination static VPN-POOL VPN-POOL
!
object network mail_server
nat (DMZ,outside) static x.x.x.179
object network mail
nat (DMZ,outside) static x.x.x.180
access-group outside_access_in in interface outside
access-group DMZ in interface DMZ
route outside 0.0.0.0 0.0.0.0 178.254.133.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action terminate
dynamic-access-policy-record dripolisa
aaa-server DRI protocol ldap
aaa-server DRI (inside) host 192.168.0.20
ldap-base-dn DC=dri,DC=local
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *****
ldap-login-dn CN=dragan urukalo,OU=novisad,OU=sektor2,OU=REVIZIJA,DC=dri,DC=local
server-type microsoft
user-identity default-domain LOCAL
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
virtual telnet 192.168.1.12
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 195.222.96.223
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.0.14-192.168.0.45 inside
!
dhcpd address 172.16.20.2-172.16.20.150 DMZ
dhcpd dns x.x.x.177 interface DMZ
dhcpd auto_config outside interface DMZ
dhcpd option 6 ip x.x.x.177 interface DMZ
dhcpd enable DMZ
!
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
!
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy GroupPolicy_x.x.x.223 internal
group-policy GroupPolicy_x.x.x.223 attributes
vpn-tunnel-protocol ikev1 ikev2
group-policy drivpn internal
group-policy drivpn attributes
dns-server value 192.168.0.20 192.168.0.254
vpn-simultaneous-logins 10
vpn-idle-timeout 30
vpn-tunnel-protocol ikev1 l2tp-ipsec
split-tunnel-network-list value Split_Tunnel_List
default-domain value dri.local
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group drivpn type remote-access
tunnel-group drivpn general-attributes
address-pool vpnadrese
authentication-server-group DRI
default-group-policy drivpn
tunnel-group drivpn ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group x.x.x.223 type ipsec-l2l
tunnel-group x.x.x.223 general-attributes
default-group-policy GroupPolicy_x.x.x.223
tunnel-group x.x.x.223 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect tftp
inspect ip-options
inspect netbios
inspect icmp
inspect http
!
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:69c651e94663fc570b67e0c4c0dcbae1
: endrunning config asa 5505
Result of the command: "show run"
: Saved
:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password csq7sfr0bQJqMGET encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.5.0 PALATA
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.17 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address 10.13.74.33 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
object-group service DM_INLINE_SERVICE_1
service-object ip
service-object tcp
service-object icmp echo
service-object icmp echo-reply
service-object tcp eq domain
service-object tcp eq ldap
service-object tcp eq smtp
object-group service DM_INLINE_SERVICE_2
service-object ip
service-object tcp eq domain
service-object tcp eq www
service-object tcp eq https
service-object tcp eq smtp
object-group service Sharepoint8080 tcp
port-object eq 8080
access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any any
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_2 192.168.0.0 255.255.255.0 any
access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list outside_2_cryptomap extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip 192.168.0.0 255.255.255.0 PALATA 255.255.255.0
pager lines 24
logging enable
logging asdm informational
logging mail errors
logging from-address
logging recipient-address level debugging
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 192.168.0.0 255.255.255.0
static (inside,outside) 10.13.74.35 192.168.0.22 netmask 255.255.255.255
static (inside,outside) 10.13.74.34 192.168.0.20 netmask 255.255.255.255 dns
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.13.74.1 1
route inside 0.0.0.0 0.0.0.0 192.168.0.17 tunneled
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication telnet console LOCAL
http server enable
http 10.13.74.0 255.255.255.0 outside
http 192.168.0.0 255.255.255.0 inside
http 10.15.100.0 255.255.255.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
virtual telnet 192.168.0.53
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_2_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer 10.15.100.15
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username driadmin password AojCAMO/soZo8W.W encrypted privilege 15
tunnel-group 10.15.100.15 type ipsec-l2l
tunnel-group 10.15.100.15 ipsec-attributes
pre-shared-key *
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
!
service-policy global_policy global
smtp-server 173.194.79.109
prompt hostname context
Cryptochecksum:4767b6764cb597f0a7b8b138587d4192
: endThank you
Hello
I have previously edited the my initial response was in fact not necessary since you were actually using full Tunnel
EDIT: Actually just noticed the the VPN client isnt using Split Tunnel. Its Full Tunnel at the moment since it doesnt have the "split-tunnel-policy tunnelspecified"
So you don't really have any of those.
Please mark the question answers and/or assess response
Ask more if necessary
-Jouni
-
Hi all
I have an obligation to create a tunnel vpn site-to-site on ASA 5510 from a remote location to my HO, I have already other site to site tunnels are on the rise and running on the ASA. This is what my remote site got the network address that is part of a subnet used in HO(192.168.10.0/24). My requirement is only my need to access remote site couple of my servers in HO, who is in the subnet 192.168.200.0/24.
Veuileez help how can I achieve this... your advice at the beginning is very appreciated...
Thanks in advance
MikaelHi Salem,
I think the installer at your end is a bit like this:
You want the remote location to access the subnet 192.168.200.0/24 behind the ASA HQ servers. In this case, you can NAT traffic from the remote site to a different subnet when you go to 192.168.200.0/24.
i.e. the 192.168.10.0/24 subnet resemble 192.168.51.0/24 when he goes to 192.168.200.0
This can be done by using political based natting:
permit access-list policy-nat ip 192.168.10.0 255.255.255.0 192.168.200.0 255.255.255.0
public static 192.168.51.0 (inside, outside) access-l policy-nat
In the encryption of the remote side access list, you will have:
cryptoacl ip 192.168.51.0 access list allow 255.255.255.0 192.168.200.0 255.255.255.0 (this is because the remote side will see 192.168.51.0/24 and not the 192.168.10.0/24)
Similarly on the end of HQ the accesslist crypto will be
XXXXX 192.168.200.0 ip access list allow 255.255.255.0 192.168.51.0 255.255.255.0
Please try this and let me know if it helps.
Thank you
Vishnu Sharma
-
VPN site to Site with client access VPN
I have a pix 500 series configured with access to the VPN client. When I set up a site to site vpn to a remote location, access to the customer no longer works. If I remove the vpn site to site, the vpn client works again. I tried the MDP and the CLI. Someone could look at my config and let me know what I'm missing. See the two configs attached.
Thank you
Lost in VPN
Ah, I missed that. You can change the States of card crypto for virtual private networks to be on the same card encryption like this...
mymap 20 ipsec-isakmp crypto map
card crypto mymap 20 match address ipsecvpn
card crypto mymap 20 peers set xxx.xxx.100.180
transform-set set mymap 20 sha - crypto card game
map mymap 65535-isakmp ipsec crypto dynamic outside_dyn_map
client card crypto mymap RADIUS authentication
mymap outside crypto map interface
or
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address ipsecvpn
card crypto outside_map 20 peers set xxx.xxx.100.180
transform-set set sha - game card crypto outside_map 20
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map the RADIUS client authentication card crypto
outside_map interface card crypto outside
-
Cannot access remote network by VPN Site to Site ASA
Hello everyone
First of all I must say that I have configured the VPN site-to site a million times before. Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks
ASA local:
hostname gyd - asa
domain bct.az
activate the encrypted password of XeY1QWHKPK75Y48j
XeY1QWHKPK75Y48j encrypted passwd
names of
DNS-guard
!
interface GigabitEthernet0/0
Shutdown
nameif vpnswc
security-level 0
IP 10.254.17.41 255.255.255.248
!
interface GigabitEthernet0/1
Vpn-turan-Baku description
nameif outside Baku
security-level 0
IP 10.254.17.9 255.255.255.248
!
interface GigabitEthernet0/2
Vpn-ganja description
nameif outside-Ganja
security-level 0
IP 10.254.17.17 255.255.255.248
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. * 255.255.255.0
!
interface GigabitEthernet0/3
Description BCT_Inside
nameif inside-Bct
security-level 100
IP 10.40.50.65 255.255.255.252
!
interface Management0/0
nameif management
security-level 100
IP 192.168.251.1 255.255.255.0
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
name-server 192.168.1.3
domain bct.az
permit same-security-traffic intra-interface
object-group network obj - 192.168.121.0
object-group network obj - 10.40.60.0
object-group network obj - 10.40.50.0
object-group network obj - 192.168.0.0
object-group network obj - 172.26.0.0
object-group network obj - 10.254.17.0
object-group network obj - 192.168.122.0
object-group service obj-tcp-eq-22
object-group network obj - 10.254.17.18
object-group network obj - 10.254.17.10
object-group network obj - 10.254.17.26
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
icmp_inside list extended access permit icmp any one
icmp_inside of access allowed any ip an extended list
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
RDP list extended access permit tcp any host 192.168.45.3 eq 3389
rdp extended permitted any one ip access list
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
pager lines 24
Enable logging
emblem of logging
recording of debug console
recording of debug trap
asdm of logging of information
Interior-Bct 192.168.1.27 host connection
flow-export destination inside-Bct 192.168.1.27 9996
vpnswc MTU 1500
outside Baku MTU 1500
outside-Ganja MTU 1500
MTU 1500 remote access
Interior-Bct MTU 1500
management of MTU 1500
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any outside Baku
ICMP allow access remotely
ICMP allow any interior-Bct
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
3 overall (RAS) interface
azans access-list NAT 3 (outside-Ganja)
NAT (remote access) 0 access-list sheep-vpn-city
NAT 3 list nat-vpn-internet access (remote access)
NAT (inside-Bct) 0-list of access inside_nat0_outbound
NAT (inside-Bct) 2-nat-ganja access list
NAT (inside-Bct) 1 access list nat
Access-group rdp on interface outside-Ganja
!
Router eigrp 2008
No Auto-resume
neighbor 10.254.17.10 interface outside Baku
neighbor 10.40.50.66 Interior-Bct interface
Network 10.40.50.64 255.255.255.252
Network 10.250.25.0 255.255.255.0
Network 10.254.17.8 255.255.255.248
Network 10.254.17.16 255.255.255.248
redistribute static
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede GANYMEDE +.
AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
key *.
AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
key *.
RADIUS protocol AAA-server TACACS1
AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
key *.
AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
key *.
authentication AAA ssh console LOCAL GANYMEDE
Console to enable AAA authentication RADIUS LOCAL
Console Telnet AAA authentication RADIUS LOCAL
AAA accounting ssh console GANYMEDE
Console Telnet accounting AAA GANYMEDE
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 Interior-Bct
http 192.168.139.0 255.255.255.0 Interior-Bct
http 192.168.0.0 255.255.255.0 Interior-Bct
Survey community SNMP-server host inside-Bct 192.168.1.27
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.10
card crypto mymap 10 transform-set RIGHT
correspondence address card crypto mymap 20 110
card crypto mymap 20 peers set 10.254.17.11
mymap 20 transform-set myset2 crypto card
card crypto mymap interface outside Baku
correspondence address card crypto ganja 10 110
10 ganja crypto map peer set 10.254.17.18
card crypto ganja 10 transform-set RIGHT
card crypto interface outside-Ganja ganja
correspondence address card crypto vpntest 20 110
peer set card crypto vpntest 20 10.250.25.1
newset vpntest 20 transform-set card crypto
card crypto vpntest interface vpnswc
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = gyd - asa .az .bct
sslvpnkeypair key pair
Configure CRL
map of crypto DefaultCertificateMap 10 ca certificatecrypto isakmp identity address
ISAKMP crypto enable vpnswc
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.0.0 255.255.255.0 Interior-Bct
SSH timeout 35
Console timeout 0
priority queue outside Baku
queue-limit 2046
TX-ring-limit 254
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.168.1.3
SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
SSL-trust ASDM_TrustPoint0 remote access point
WebVPN
turn on remote access
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal group ssl policy
attributes of group ssl policy
banner welcome to SW value
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
group-lock value SSL
WebVPN
value of the SPS URL-list
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the PFS
BCT.AZ value by default-field
ssl VPN-group-strategy
WebVPN
value of the SPS URL-list
IPSec-attributes tunnel-group DefaultL2LGroup
ISAKMP retry threshold 20 keepalive 5
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
IPSec-attributes tunnel-group DefaultWEBVPNGroup
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.10 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.10
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type SSL tunnel-group remote access
attributes global-group-tunnel SSL
ssl address pool
Authentication (remote access) LOCAL servers group
Group Policy - by default-ssl
certificate-use-set-name username
Group-tunnel SSL webvpn-attributes
enable SSL group-alias
Group-url https://85. *. *. * / activate
tunnel-group 10.254.17.18 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.18
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.11 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.11
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type tunnel-group DefaultSWITGroup remote access
attributes global-tunnel-group DefaultSWITGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultSWITGroup
pre-shared key *.
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
class flow_export_cl
flow-export-type of event all the destination 192.168.1.27
class class by default
flow-export-type of event all the destination 192.168.1.27
Policy-map Voicepolicy
class voice
priority
The class data
police release 80000000
!
global service-policy global_policy
service-policy interface outside Baku Voicepolicy
context of prompt hostnameCryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
: end
GYD - asa #.ASA remote:
ASA Version 8.2 (3)
!
ciscoasa hostname
activate the encrypted password of XeY1QWHKPK75Y48j
2KFQnbNIdI.2KYOU encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.80.14 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 10.254.17.11 255.255.255.248
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
nameif management
security-level 100
no ip address
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
access-list 110 scope ip allow a whole
192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
management of MTU 1500
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside) 0 access-list sheep
Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.80.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.9
mymap 10 transform-set myset2 crypto card
mymap outside crypto map interface
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPNtunnel-group 10.254.17.9 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.9
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostnameCryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
: end
ciscoasa # $Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas
Would appreciate any help. Thank you in advance...
If the tunnel is up (phase 1), but no traffic passing the best test is the following:
Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.
inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside
The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).
Test on both directions.
Please post the results.
Federico.
-
Internal access to the site at the remote location via wifi
We have an internal site to A location and we have a 2 layer hose B location. When you use the ethernet connection, site B can access the site. What we want to do, is allow them to access via wifi with the VPN site to site (who currently works) hosted by of our Sonicwall.
How this is a problem is our network is separate; wifi at site B is on the DMZ. We added access rules to allow the DMZ-> VPN traffic on the site, which did not work; No ping, no traffic, no communication. We've also added policy NAT, same story.
My theory on why it does not work is because the VPN tunnel to one SW to another is related to X 0, but even after enabling access, it's the same result.
Any help would be appreciated. Thank you all!
Hello
Is DMZ subnet to site B added under 'Local networks' VPN B Site and under 'Remote Networks' policy in Site A VPN policy? If you have then SonicWALL auto-créera access rules to allow WiFi traffic. Basically, you need to add the DMZ subnet in site B the VPN policy.
You can also see the article: https://support.software.dell.com/kb/sw7725
-
VPN site to Site with restrictions (vpn-filter)
VPN site to site, I installed and it works fine and two site can meet but I question after the vpn enforcement - run under Group Policy
restrict users in the local site for dial-up networking with specific tcp ports, the vpn does not not like after order question «sh l2l vpn-sessiondb»
This works but users can't access something in the remote site
Note > after rising online in ACL at the end with this
US_SITE ip access list allow a whole
new to works well again
example of a line of Access-List
US_SITE list extended access permit tcp host 10.68.22.50 host 192.168.10.23 HTTP_HTTPS object-group
US_SITE list extended access permit tcp host 10.68.22.50 host 192.168.10.24 HTTP_HTTPS object-grouplocal network: 10.68.22.50
remote network: 192.168.10.24
is that correct or not?
attributes of the strategy group x.x.x.x
value of VPN-filer US_SITEtunnel-group General y.y.y.y
x.x.x.x by default-group-policyNote: allowed sysopt active vpn connection
The syntax on ACL that is used as a vpn-filter is different from what is normally expected. These VPN filters is not a direction, it should be noted the traffic we want to allow incoming and outgoing of the VPN in an ACL. The syntax for this is:
access-list X permit/deny REMOTE-DEFINITION LOCAL-DEFINITION
Example: You want to allow local users to access the RDP on the remote site:
access-list VPN-ACL permit tcp host 192.168.10.24 eq 3389 10.68.22.0 255.255.255.0
Disadvantage: This is all really confusing, and you can't afford things like Ping in one direction. -
VPN site to Site with ASA 5520 * please help *.
I am using two ASA 5520, and try to put up a site to site VPN. This seems to be pretty simple, but I'm on my third day of train this is up and running. Both 5520's are running the latest 9.1 (5) IOS.
Please note: I replaced it with [#1-WAN IP] and [#2-WAN IP] for WAN IP of the ASA addresses.
Thanks in advance for any help you may have.
-------------------------------------------------------------------------------------------------------------------------------------------------
ASA 5520 # 1:
Crypto ikev1 allow outside
the local object of net network
10.0.0.0 subnet 255.255.255.0net remote object network
172.20.0.0 subnet 255.255.255.0outside_1_cryptomap list of allowed ip object local net net access / remote
tunnel-group [IP #2-WAN] type ipsec-l2l
IPSec-attributes tunnel-group [#2-WAN IP]
pre-shared-key cisco123IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
card crypto oustide_map 1 match address outside_1_cryptomap
card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
card crypto outside_map 1 set pfs Group1
map 1 set outside_map crypto peer [#2-WAN IP]
outside_map interface card crypto outsideNAT (inside, outside) 1 local static source net net-local destination static remote net net / remote
-------------------------------------------------------------------------------------------------------------------------------------------------
ASA 5520 #2:
Crypto ikev1 allow outside
the local object of net network
172.20.0.0 subnet 255.255.255.0net remote object network
10.0.0.0 subnet 255.255.255.0outside_1_cryptomap list of allowed ip object local net net access / remote
tunnel-group [#1-WAN IP] type ipsec-l2l
IPSec-attributes tunnel-group [#1-WAN IP]
pre-shared-key cisco123IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
card crypto oustide_map 1 match address outside_1_cryptomap
card crypto oustide_map 1 set transform-set ESP-3DES-SHA ikev1
card crypto outside_map 1 set pfs Group1
map 1 set outside_map crypto peer [#1-WAN IP]
outside_map interface card crypto outsideNAT (inside, outside) 1 local static source net net-local destination static remote net net / remote
Try to correct the mistakes in the two configs.
In some places, you have 'oustide_map' where you need "outside_map".
-
Problem VPN site to Site with overlapping networks
We currently have a PIX 515E firewall as a headboard with many tunnels of site-to-site configured for her with the enpoints of PIX 506. Our internal LAN addressing scheme is 172.18.0.0 255.255.0.0. Addresses of local network in two of the remote networks with congigured VPN site-to-site are 172.18.107.0 255.255.255.224 and 172.18.107.32 255.255.255.0. Remote network access to all services on our internal network very well. We have 20 other network segments configured the same way. The 172.18.107.32.0 network needs to communicate with the 172.18.107.0 network for the services of file on the other remote PIX. Since the station PIX will not allow traffic to leave the same interface it came we thought with him we would just set up a tunnel from site to site between the two remote LAN. After the configuration of the site to another remote firewalls do not appear to try to establish tunnels when sending valuable traffic. I turned on debug for ISAKMP and nothing is either sent or received on a remote Firewall with regard to these tunnels. It's almost like since we already have a tunnel set to our 172.18.0.0 internal LAN that the remote PIX will not build specifically to 172.18.107.0 tunnel. I am able to ping each remote peer with each other and hear protection rules, but nothing has ever been established.
Is what we are trying to do possible? Sorry for the long post but the kind of a strange scenario. Thanks in advance for any help.
In what order are the numbers of seqence card crypto for configuring vpn on pix distance units? It could be that you are trying to install is a lot and will be checked later as head of pix. If this is the case, then yes the 172.18/16 road prevail the 172.18.107/24. Try to rebuild the entrance card crypto with a lower number so that traffic to 172.18.107/24 comes first.
I would like to know how it works.
-
Need urgent help in the configuration of the Client VPN IPSec Site with crossed on Cisco ASA5510 - 8.2 (1).
Here is the presentation:
There are two leased lines for Internet access - a route 1.1.1.1 and 2.2.2.2, the latter being the default Standard, old East for backup.
I was able to configure the Client VPN IPSec Site
(1) with access to the outside so that the internal network (172.16.0.0/24) behind the asa
(2) with Split tunnel with simultaneous assess internal LAN and Internet on the outside.
But I was not able to make the tradiotional model Hairpinng to work in this scenario.
I followed every possible suggestions made on this subject in many topics of Discussion but still no luck. Can someone help me here please?
Here is the race-Conf with Normal Client to Site IPSec VPN configured with no access boarding:
LIMITATION: Cannot boot into any other image ios for unavoidable reasons, must use 8.2 (1)
race-conf - Site VPN Customer normal work without internet access/split tunnel
:
ASA Version 8.2 (1)
!
ciscoasa hostname
domain cisco.campus.com
enable the encrypted password xxxxxxxxxxxxxx
XXXXXXXXXXXXXX encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside internet1
security-level 0
IP 1.1.1.1 255.255.255.240
!
interface GigabitEthernet0/1
nameif outside internet2
security-level 0
IP address 2.2.2.2 255.255.255.224
!
interface GigabitEthernet0/2
nameif dmz interface
security-level 0
IP 10.0.1.1 255.255.255.0
!
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
IP 172.16.0.1 255.255.0.0
!
interface Management0/0
nameif CSC-MGMT
security-level 100
the IP 10.0.0.4 address 255.255.255.0
!
boot system Disk0: / asa821 - k8.bin
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
domain cisco.campus.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group network cmps-lan
the object-group CSC - ip network
object-group network www-Interior
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
port udp-object-group service
object-group service ftp
object-group service ftp - data
object-group network csc1-ip
object-group service all-tcp-udp
access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3
access-list extended SCC-OUT permit ip host 10.0.0.5 everything
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp
list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3
access CAMPUS-wide LAN ip allowed list a whole
access-list CSC - acl note scan web and mail traffic
access-list CSC - acl extended permit tcp any any eq smtp
access-list CSC - acl extended permit tcp any any eq pop3
access-list CSC - acl note scan web and mail traffic
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq www
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq https
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq smtp
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq pop3
access-list extended INTERNET2-IN permit ip any host 1.1.1.2
access-list sheep extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0
access list DNS-inspect extended permit tcp any any eq field
access list DNS-inspect extended permit udp any any eq field
access-list extended capin permit ip host 172.16.1.234 all
access-list extended capin permit ip host 172.16.1.52 all
access-list extended capin permit ip any host 172.16.1.52
Capin list extended access permit ip host 172.16.0.82 172.16.0.61
Capin list extended access permit ip host 172.16.0.61 172.16.0.82
access-list extended capout permit ip host 2.2.2.2 everything
access-list extended capout permit ip any host 2.2.2.2
Access campus-lan_nat0_outbound extended ip 172.16.0.0 list allow 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
Enable logging
debug logging in buffered memory
asdm of logging of information
Internet1-outside of MTU 1500
Internet2-outside of MTU 1500
interface-dmz MTU 1500
Campus-lan of MTU 1500
MTU 1500 CSC-MGMT
IP local pool 192.168.150.2 - 192.168.150.250 mask 255.255.255.0 vpnpool1
IP check path reverse interface internet2-outside
IP check path reverse interface interface-dmz
IP check path opposite campus-lan interface
IP check path reverse interface CSC-MGMT
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
interface of global (internet1-outside) 1
interface of global (internet2-outside) 1
NAT (campus-lan) 0-campus-lan_nat0_outbound access list
NAT (campus-lan) 1 0.0.0.0 0.0.0.0
NAT (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT, internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
Access-group INTERNET2-IN interface internet1-outside
group-access INTERNET1-IN interface internet2-outside
group-access CAMPUS-LAN in campus-lan interface
CSC-OUT access-group in SCC-MGMT interface
Internet2-outside route 0.0.0.0 0.0.0.0 2.2.2.5 1
Route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication enable LOCAL console
Enable http server
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
HTTP 1.2.2.2 255.255.255.255 internet2-outside
HTTP 1.2.2.2 255.255.255.255 internet1-outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs set group5
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
Crypto map internet2-outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
crypto internet2-outside_map outside internet2 network interface card
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as
quit smoking
ISAKMP crypto enable internet2-outside
crypto ISAKMP policy 10
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
Telnet 10.0.0.2 255.255.255.255 CSC-MGMT
Telnet 10.0.0.8 255.255.255.255 CSC-MGMT
Telnet timeout 5
SSH 1.2.3.3 255.255.255.240 internet1-outside
SSH 1.2.2.2 255.255.255.255 internet1-outside
SSH 1.2.2.2 255.255.255.255 internet2-outside
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal VPN_TG_1 group policy
VPN_TG_1 group policy attributes
Protocol-tunnel-VPN IPSec
username ssochelpdesk encrypted password privilege 15 xxxxxxxxxxxxxx
privilege of encrypted password username administrator 15 xxxxxxxxxxxxxx
username vpnuser1 encrypted password privilege 0 xxxxxxxxxxxxxx
username vpnuser1 attributes
VPN-group-policy VPN_TG_1
type tunnel-group VPN_TG_1 remote access
attributes global-tunnel-group VPN_TG_1
address vpnpool1 pool
Group Policy - by default-VPN_TG_1
IPSec-attributes tunnel-group VPN_TG_1
pre-shared-key *.
!
class-map cmap-DNS
matches the access list DNS-inspect
CCS-class class-map
corresponds to the CSC - acl access list
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
CCS category
CSC help
cmap-DNS class
inspect the preset_dns_map dns
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Adding dynamic NAT for 192.168.150.0/24 on the external interface works, or works the sysopt connection permit VPN
Please tell what to do here, to pin all of the traffic Internet from VPN Clients.
That is, that I need clients connected via VPN tunnel, when connected to the internet, should have their addresses IP NAT'ted against the address of outside internet2 network 2.2.2.2 interface, as it happens for the customers of Campus (172.16.0.0/16)
I am well aware of all involved in here, so please be elaborative in your answers. Please let me know if you need more information about this configuration to respond to my request.
Thank you & best regards
MAXS
Hello
If possible, I'd like to see that a TCP connection attempt (e.g. http://www.google.com) in the ASDM logging of the VPN Client when you set up the dynamic NAT for the VPN Pool also.
I'll try also the command "packet - trace" on the SAA, while the VPN Client is connected to the ASA.
The command format is
packet-tracer intput tcp
That should tell what the SAA for this kind of package entering its "input" interface
Still can not see something wrong with the configuration (other than the statement of "nat" missing Dynamics PAT)
-Jouni
-
VPN site to Site with the IP address range internal Natting?
This is our real internal LAN address: 10.40.120.0/26 (internal range) and I want to translate to
Translated the address: 10.254.9.64.255.255.255.192 (Internal)
Our remote local address is: 10.254.5.64 site 255.255.255.192(Remote adresse Ip interne ajouter plage)
Based on the above parameters I did this configuration
outside_cryptomap ip 10.254.9.64 access list allow 255.255.255.192 10.254.5.64 255.255.255.192
policy-nat of ip 10.40.120.0 access list allow 255.255.255.192 10.254.5.64 255.255.255.192
public static 10.254.9.64 (inside, outside) - list of access policy-natI had all the phase 1 and Phase 2 required parameters and add public ip peer.
I had set up vpn by using ASDM before but this scenario is new for me, all I was wondering is there anything I need to properly configure Setup VPN
If you see TX increases but not RX which means that traffic is sent to the remote end however there is no response.
I suggest that you check with the remote end of VPN to see where is the problem. It is very probably the remote side.
-
ASA (v9.1) VPN from Site to Site with IKEv2 and certificates CEP/NDE MS
Hi all
I am currently a problem with VPN Site to Site with IKEv2 and certifiactes as an authentication method.
Here is the configuration:
We have three locations with an any to any layer 2 connection. I created each ASA (ASA5510 worm 9.1) to establish one VPN of Site connection to the other for the other two places. Setting this up with pre shared keys and certificates that are signed by the CA MS administrator manually work correctly.
But when we try to enroll these certificates through the Protocol, CEP/NDE his does not work.
Here are my steps:
1 configure the CA Turstpoint to apply to the certification authority
2. request that the CA through the SCEP protocol works fine
3. set up a Trustpoint and a pair of keys for the S2S - VPN connection
4. registration form identity certificate CA via the SCEP Protocol with a one time password works fine
5. set the trustpoint created as for the S2S - VPN IKEv2 authentication method.
Now I did it also for the other site of the VPN Tunnel. But when I ping on a host that is on a different location to make appear the Tunnel VPN - the VPN session is not established. In the debugs I see that there are a few problems during authentication of the remote peer.
On the MS that I see that the certifactes of identity for both ASAs are communicated and not revoked or pending state. The certificate based on the model of the "IPSec (Offline).
When the CA-Admin and a certificate me manually based on a copy of the model of "Domaincontroller" connection is successfully established.
So I would like to know which is the correct certificate for IP-Sec peers template to use for the Protocol, CEP and MS Enterprise CA (its server 2008R2 of Microsoft Enterprise)?
Anyone done this before?
ASA requires that the local and Remote certificate contains EKU IP Security Tunnel Endpoint (1.3.6.1.5.5.7.3.6) (aka IP Security Tunnel termination). You can create a Microsoft CA model to add.
If you absolutely must go with the 'bad' cert, there is a command
ignore-ipsec-keyusage
but it is obsolete and not recommended.
Meanwhile at the IETF:
RFC 4809
3.1.6.3 extended Key use
Extended Key Usage (EKU) indications are not required. The presence
or lack of an EKU MUST NOT cause an implementation to fail an IKE
connection.
Maybe you are looking for
-
I received a ' reminder: update your Apple ID ". It's a spam?
I received a ' reminder: update your Apple ID ". It's a spam? Here is the message: Dear Due to recent updates, we ask a lot of our customers to update their information, it's nothing to worry about. We ensure that we have the correct information on t
-
Equium A200-1VO - "a disk read error has occurred."
Hello I had my Equium A200-1VO since December 2007 and has never really had any problems with it atall. However, last night after a Windows Vista update and restart, my laptop won't start upward. I get a black screen announcing: "A disk read error ha
-
I have a problem when I open Microsoft Excel or an excel file, I get a screen with the following message:Preparing to install Microsoft Office XP Professional with FrontPagePlease wait while Windows configures Microsoft Office XP Professional with Fr
-
Undetected device, Samsung S2 portable 1 TB, 3 flashes on the device.
When I plug the hard drive to the USB the blue light on the device turns on then turns off, then several sets of 3 flashes. No trecognised on laptop running windows 7. There is an answer cause its doin my head. From the other thread: http://answers.M
-
Uninstalling HP protect Tools Security Manager
I don't think that anyone from MS really knows how to uninstall HP protect tools. All post are just all over the place. The question is simple how to uninstall HP security protect the tools from a Windows 7 computer. HP support is no help I'm beginni