2 VPN to separate networks with the same intellectual property regime

We have an office in Bermuda and 2 offices in Chicago. 2 offices in Chicago have the same pattern of IP - 10.150.1.0/24. I would like to set up a VPN site-to site of Bermuda for each of the offices of Chicago. I have one up and it works fine. When I set up the 2nd, I can pass in Chicago, but not receive. I guess it has to do with the same IP networks. Is there a way around this problem?

Thank you

Scott

Yes you need to nat all traffic goes to one of the sights of Chicago. This way others will see it as a completely different subnet. It is a guide of cisco.com:

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9950.shtml

Tags: Cisco Security

Similar Questions

  • L2L configuration with the same intellectual property regime

    Hi all

    hoefully it won't be easy. I set up some VPN site to site, but now I have one that has a plan of the same IP as me. 192.168.9.x is the subnet in question. I think I'll need to NAT, the jobs of 192.168.9.x who will have access to my network. I usually add a rule exempt from NAT for my other L2L sites, but since I'm on NAT for this one I can not add, correct? Also, I think that when I add a route statement to my router I point to the NAT address... Thanks in advance for any help.

    Please visit the following OCC configuration guides...

    http://www.Cisco.com/en/us/partner/products/ps5855/products_configuration_example09186a0080a0ece4.shtml

    http://www.Cisco.com/en/us/partner/products/ps6120/products_configuration_example09186a0080b37d0b.shtml

  • Message appear conflict of IP address at startup. Another computer already uses the network with the same IP address. How do I cure this?

    When my kids play online on the X - Box I get an error message on my laptop when I start after them. It is said there is an IP address conflict and that another device is already on the network with the same IP address. It does not affect me access internet even if. How can I fix thi.

    Hello

    1. which is the version of Windows installed on the computer? For example, Windows 7, Vista

    2. only the error message appears only when the Xbox is connected to the computer or at both times?

    3. have you made any software or changes to the material on the computer before this problem?

    Please answer these questions and provide additional information so that we can better guide you.

  • my windows says that another computer is running in the same network with the same ip address, please contact

    Today morning when I opened my samsung mini, it displays a message that another computer is running on the same network with the same ip address please find a solution for this

    In most home networks where multiple devices are connected to a router, router will assign an IP address to each device (via DHCP). This method keeps usually different devices to get the same IP address, but if you restart your router, it will not address remembered that he released before it was restarted.  This condition can also occur if you manually assigned an IP address to a device located in the router's DHCP range.  If the problem is not due to manually assign an IP address, then this condition will be corrected over time.  But if you're in a hurry, you can unplug your router from the wall and stop all computing devices on it.  Then plug the router back in and bring up all your devices again one by one.

    HTH,

    JW

  • My PC shows that there is someone else on my network with the same IP address. Could this be my Kindle Fire?

    I get the message on my computer that there is someone else on my network with the same IP address.  Could this be my Kindle Fire, that generated the message?

    In many cases, the ip addresses are assigned automatically by the router and if this is the case, something that can happen (happened to me) is that if several computers are attached (via wifi or ethernet or a combination of the two) and the router restarts while a computer is in sleep mode, when the router reboots it know that the computer sleeps is here and it can affect the ip address that has been already assigned to another computer.  When the computer sleep resumes usage it will trigger the dupicate ip address error.  In this case, you can just stop everything and restart.  The following discusses other causes and solutions: http://windows.microsoft.com/en-US/windows7/Get-help-with-There-is-an-IP-address-conflict-message

  • several devices on the network with the same name

    I want to install Windows 7 OS computers on a domain with Small Business SERVER 2003.  Curiously, I see all the computers on the network, where I should be able to, but one of them WK02011, is not accessible from all Windows 7 systems because there are multiple devices with the same name on the network according to a diagnosticn check.  WK02011 is visible and accessible from other systems on the network that are runjning XP OS.  There is only one device named WK02011 on the network.  I don't have this problem with any other XP system - that is - I can see and access all of the other XP machines on the network with the exception of WK02011.  I can't access WK2011 from the server and the server indicates that it is multiple devices with the same ID.  Rename the XP would be complicated because of having to re - set up the service to the customer and then turn around and install 7 OS in the workstation in the coming days.

    How to find the ghost device double?

    Hello

    Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows 7 on TechNet. Please post your question in the Technet forums. You can follow the link to your question:

  • ASA 5520-Duplicate Object - network with the same ip address

    Hello friends,

    We have 5 people work as a team, some in collaboration with CLI and Assistant Deputy Ministers.

    now, we have seen with the same IP address other network objects are created,.

    now some time its difficult to solve or monitoring

    can someone help me to find a solution so that nobody can create any object with the same IP address.

    You could do with a technical solution like EEM where you analyze syslog to see if someone sets up an object with an IP address and then act on it. But WWM has 9.2 which is not available for the 5520.

    If you can solve the problem with an organizational solution. Apply a standard for naming, how objects should be appointed, ensuring that everyone watches he objects before creating new and more important, you must talk to each other which will configure that.

  • Is droid - possible to separate people with the same names?

    My list of contacts and Facebook was related, but I have friends that have the same names and is there a way to separate contacts in a way people list? Help, please.

    When you look at the contact (I assume that the two are joined) you can select the menu and 'change '. Once you have "edit" on the screen, see if there is a "Separate" menu item If so, who should take care of it.

  • Conflicts of addsess IP in Windows 7, error "There is another device on the network with the same IP address".

    Conflicts of addsess title: original win 7 IP

    I just bought a used laptop, it has been deleted I made it mine I addminastrater pc name willards pc and whatnot, but I continue banging off the internet because address conflict IP said that there is a nother design on network with my address, I don't know how fix it can you please help me?

    Hi Willard,

    Please contact Microsoft Community. I've surely you will help solve this problem.

    This problem could occur due to incorrect parameters TCP\IP.

    Try the steps listed here:

    Method 1:

    I suggest you to reset TCP\IP and check if it helps.

    How to reset TCP/IP using the NetShell utility
    https://support.Microsoft.com/en-us/KB/299357

    Method 2:
    If the problem persists, I suggest you try the following steps to flush the DNS and request a new IP address of the server of your ISP. Check if it helps.

    1. Cclick on Start and type cmd in start search.
    2. Right click on command prompt run , then selectas administrator.
    3. At the command prompt, type the following commands and press enter after each command.

    ipconfig/flushdns

    ipconfig/registerdns

    ipconfig/release

    ipconfig / renew

    output

    Hope this information helps. Reply to the post with an up-to-date report of the issue so that we can help you further.

  • Easy VPN setup with interface to multiples with the same level of security

    Hello

    I want to configure an ASA 5505 with 7.2 (4) software and dual license ISP and when I configure two interfaces with the level 0 on two security interfaces and enable vpnclient the trace message appear:

    ERROR: Cannot determine the internal and external interfaces Easy VPN remote: multiple interfaces with the same levels of security.

    vpnlclient of configuration above:

    vpnclient Server x.x.x.x where x.x.x.x
    vpnclient mode network-extension-mode
    vpnclient nem-st-autoconnect
    vpnclient TUNNEL_EZVPN_TUNNELSPEC vpngroup password *.
    vpnclient username usr_ezvpn_tunnelspec password *.
    vpnclient enable

    interfaces:

    interface Vlan200
    nameif outside1
    security-level 0
    IP x.x.x.x 255.255.255.252
    !
    interface Vlan300
    nameif outside2
    security-level 1
    IP x.x.x.x 255.255.255.128
    !

    monitor the SLA to the routing:

    monitor SLA 100
    type echo protocol ipIcmpEcho 200.221.2.45 interface outside1
    NUM-package of 5
    frequency 30
    monitor als 100 calendar life never start-time now
    ALS 200 monitor
    type echo protocol ipIcmpEcho 200.154.56.80 interface outside2
    NUM-package of 5
    frequency 30
    Annex monitor SLA 200 life never start-time now
    ALS 300 monitor
    type echo protocol ipIcmpEcho 4.2.2.1 interface outside1
    NUM-package of 5
    frequency 30
    Annex monitor SLA 300 life never start-time now
    ALS 400 monitor
    type echo protocol ipIcmpEcho 200.244.168.149 interface outside1
    NUM-package of 5
    Timeout 3000
    threshold of 3000
    frequency 30
    Annex monitor SLA 400 life never start-time now

    Follow-up:

    !
    track 1 rtr 400 accessibility
    !
    Track 2 rtr 200 accessibility
    !

    routes:

    Route 0.0.0.0 outside1 0.0.0.0 x.x.x.x 100 track 1
    Route 0.0.0.0 outside2 0.0.0.0 x.x.x.x 200 track 2

    The track works normal.

    Kind regards!

    Try using the command "backup interface" on the secondary ISP interface.

    http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/b_72.html#wp1338585

    You need to increase the level of security to 1 for this interface.

    By default, EasyVPN uses the highest level of safety inside and the lowest outside.  Anything between the two must be set manually.  I assume you have an interior vlan defined but not added to the posted config.

  • Limitation of connection with the same credentials of AD to EHT

    Hi all

    I want that if a client has a successful login - started session in the company with access to its network domain account, it cannot connect to the network with the same domain to another account at the same time.

    I have to try to prevent the connection several successful sessions simultaneously with the same credentials of domain of different devices.

    Thank you

    Hello

    I have already spoken here, and also with local Cisco SE and for the moment, the ISE does not have a mechanism to limit the number of sessions per user name, this feature is only available for guest users.

    In addition, we have a work around for this on Cisco WLC (wireless) since the WLC has a feature to limit the number of sessions per user name, and also you can limit the number of sessions on the SAA for VPN access.

    There is no work around to access switches, so you need to make a policy on the AD domain / itself, if necessary.

    Thank you.

    Ahmad.

  • Implementation of Airport extreme with the same SSID

    My House has very thick walls and so I run a Cat5 cable for a number of rooms and installed an Airport Extreme for everyone to create a local WiFi network.

    For the moment, each creates its own wi fi network which is very good for connecting phones, tablets and laptops but I'm trying to connect some SONOS devices and they are not find each other so not a link to the main controller of SONOS.

    SONOS support suggests that if I could get the extremes of the airport on the same SSID, which should help you because they would all be network extensions and so devices would be able to find each other.

    I tried making them all extensions of the network wi fi router but can't see not in the options when I select "Extend an existing network", although on my iPad, I can see wi fi network to the router where the Airport Extreme is so too, it is wired to the router would have thought it should be possible to make all the extensions of a single network.  Research in the community, it seems that the airport is unable to extend a wifi network not Apple, but I could at least get all the airports on the same SSID can help.  I also tried to set up airports so they all extend the network, but they do not see each other because they are too far away.

    I'm not an expert in network management, I understand bits having to solve problems earlier, but if there is there advice or suggestions of the community that would be great

    Thank you

    David

    You choose to extend a network when the incoming signal is wifi. What you need is a "mobile network". Simply connect each airport to the router by ethernet and network with the same SSID and password than the original. Reset the airports so that they put in place from the new so that they detect the arrangement and get into bridge mode - you do not want to provide the IP numbers, you want the home router to do and airports to pass.

    See this page and scroll down to "Roaming Network (Wi - Fi connected base stations)':"

    Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo...

  • Welcome with the same IP address of a default gateway. How to prevent?

    Hello

    This week, I had a problem in the network. A host has been connected to the network with the same IP address of the gateway by default of this Vlan.

    Is there a way to prevent it? I know with 802.11 x I know who done it, but it would avoid the problem to occur.

    Is there anyway to force the hosts to use DHCP or something?

    It will also prevent an unauthorized on an untrusted interface DHCP server. It provides (on an untrusted interface) only DHCP client messages such as DHCP queries (rejects messages from the DHCP server as DHCP responses) and allows only the source IP address packages he knows the addresses assigned by DHCP. Who is?

    Darren

  • Several groups of ports with the same VLanID

    Ask a question on peoples experience or knowledge, because we had a little chat here at work. If you have several groups with the same VLanID virtual port in the same cluster, does or that will cause a problem?

    Tom - we do that regularly.

    We have large quantities of VLAN - and often will be have 2 VMs hosted on the same Vlan environments for the purposes of the Dev - but when we move to production, we want to be able to isolate the dependent VMs to the configured network - with the same Vlan in use. . with a name different from the ways that we can quickly determine which is which.

    In addition

    I have hhave 1 vSwitch, with 2 natachasery (set up for tolerance of failure... not load balancing). . 2 groups of ports. . even vLan. . but I can get then Port Group1 to Teddy defauilt 1 and Port Group2, or Teddy bear 2 - which means I can isolate traffic e.. except in an emergency.

  • Two VPN tunnels on the same device with the same protected networks

    There is a remote site that wants me to put in place two separate tunnels of VPN with the same internal IP at each end. FOR EXAMPLE

    LAN = 10.212.170.201/32, 10.212.170.202/32

    Remote network 192.168.0.0/24 =

    I currently have a tunnel between the above:

    End Point distance = 111.93.152.186

    Local endpoint point = 198.205.115.252

    Now, they want to set up a VPN for the same networks between:

    End Point distance = 115.115.130.34

    Local endpoint point = 198.205.115.252

    It is my understanding that the Cisco ASA 5520 can do. The only way I've seen this done with Cisco hardware is to use two ASAs, but there may be a way to use the costs of road or some other tricks to make it happen.

    I'm open to suggestions.

    Is a backup?

    In, specify endpoint remote second as a "backup" of the peer in the first virtual private network.  Alone will be active at the time - but there are toggled if the VPN in first dies.

Maybe you are looking for