Similar Questions

• Problem of airtime with the same SSID

  I often use AirPlay to my iPhone and iTunes on my PC to play for my (home theater installation) AVR - 1506 Marantz.

  Configuring wifi in our House are a router/modem to the ISP and an Asus RT-N56U (in access point mode) with DIFFERENT SSID to which I don't have problem to play AirPlay on any device. I had the same SSID when so I can use wifi roaming without having to change the SSID whenever the other signal weakens.

  When I put two (router & AP) with the same SSID, Airplay icon will not be displayed? But if I put a different SSID to one of the two, airplay icon is back. Channels are on ch.1 (router) and ch.11 (AP). Someone knows how to set up?

  UPDATE:

  Disable NAT in fact access point the AirPlay icon always appear but he cannot yet play through my APR.

  * all updates *.

  12.4.3 iTunes

  Windows 10 updated, firewall offshore

  Marantz 1506 firmware update

  always put iPhone to update to the latest version

  The routers are also updated to its latest firmwares

  What I believe you are describing is a network expanded through repetition, the Apple TV does not work well with repeaters. Try a different configuration.

• Satellite R830-1GZ: ConfigFree Radar fails to display the networks without wire with the same SSID

  I have a new R830-1GZ Satellite with Windows 7 and a (much) older Portege M300 - all have two versions of Radar on them.

  However, while the old machine display correctly anywhere wireless and signal forces - even when there are multiple places with the same SSID - I use Powerline Extenders to extend coverage, the new machine with the last RADAR doesn't seem to be able to cope with these multiple identical wireless spots and fails to show more than one at a time - and then reliably.

  I should add that both machines work quite well in fact using the same SSID points connecting to the stronger.

  Is there a utility round way this or another that correctly displays it available different SSID and strength.

  Thank you very much

  Bill

  > Is there a utility round way this or another that correctly displays it available different SSID and strength?

  As far as I know there is no other Toshiba utility that could manage wireless networks and display devices Bluetooth as ConfigFree don't.

  I found some useful Q / A ConfigFree regarding:
  [ConfigFree: answers Questions &: http://www.toshiba.eu/innovation/solution_content_article.jsp?z=42&SOLUTION_ID=Conf igFree_QandA]

  Look also in Toshiba's technical knowledge base and search for Configfree for useful documents.
  http://www.Toshiba.EU/innovation/generic/TKB_SUPPORT/

• Implementation of Airport extreme with the same SSID

  My House has very thick walls and so I run a Cat5 cable for a number of rooms and installed an Airport Extreme for everyone to create a local WiFi network.

  For the moment, each creates its own wi fi network which is very good for connecting phones, tablets and laptops but I'm trying to connect some SONOS devices and they are not find each other so not a link to the main controller of SONOS.

  SONOS support suggests that if I could get the extremes of the airport on the same SSID, which should help you because they would all be network extensions and so devices would be able to find each other.

  I tried making them all extensions of the network wi fi router but can't see not in the options when I select "Extend an existing network", although on my iPad, I can see wi fi network to the router where the Airport Extreme is so too, it is wired to the router would have thought it should be possible to make all the extensions of a single network.  Research in the community, it seems that the airport is unable to extend a wifi network not Apple, but I could at least get all the airports on the same SSID can help.  I also tried to set up airports so they all extend the network, but they do not see each other because they are too far away.

  I'm not an expert in network management, I understand bits having to solve problems earlier, but if there is there advice or suggestions of the community that would be great

  Thank you

  David

  You choose to extend a network when the incoming signal is wifi. What you need is a "mobile network". Simply connect each airport to the router by ethernet and network with the same SSID and password than the original. Reset the airports so that they put in place from the new so that they detect the arrangement and get into bridge mode - you do not want to provide the IP numbers, you want the home router to do and airports to pass.

  See this page and scroll down to "Roaming Network (Wi - Fi connected base stations)':"

  Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo...

• 3070 connectivity problem - multiple Accespoints with the same SSID

  Hi all

  I have a problem with my printer HP Deskjet 3070 printer all-in-one.

  I have 2 accespoints with the same SSID for better coverage of the pit of the wireless home network.

  For some reason any my HP printer keeps losing wireless connection when the 2 accespoints are rising.

  I use a different frequency for the 2 accespoints channel and it works fine with all other wireless devices.

  I did that a DHCP are used, r, but in fact it doesn't matter because the printer uses a static IP (192.168.0.3)

  When the two AP is the printer loses wirelesss connectivity. (The blue led will blink)

  If I take one of the accespoints offline, the printer becomes available.

  Is this a problem on my end or a problem of software/firmware printer?

  Kind regards

  -eth0

  Lol this is not very clear to me?

  But it is very good that we continue here:

  http://h30499.www3.HP.com/T5/printers-DeskJet/3070A-connectivity-issue-multiple-Accespoints-with-the-same-SSID/TD-p/5865699#.UKNyiYatlI1

• Must configure with the same SSID of the AP

  We are looking for the purchase of two Access Points to our new building.  We currently have at our old facility two end bottom of AP with two different SSIDs.  Manaully users simply switch between the two.  I would like to know how it would be difficult to set up it would not have users to manually switch as they traveled through the building.

  I have looked at Cisco AP below and I was wondering if she had the ability to do so.  Is there another hardware or software needed to put up something like that.

  Just to clarify I only need two AP and want things transperent to my users.  I want them to be able to walk the area covered to another area covered by the AP2 and AP1 and loose no matter what connection.  Here it's automatic for users do not have to do anything to move things.

  Any info anyone can provide to help me would be greatly appreceated.  Thanks in advance.

  Access point wireless Cisco Aironet 1140 AIR-LAP1141N-A-K9

  As I understand it, you can configure both with the same SSID settings and security and that they will be 'transparent' to switch to the other. It is if you do not use something like an IP phone that requires a quick transition between the two. In this case, you would need a controller.

• Cisco APs with the same SSID

  I have a few Cisco 1200 APs series and when I put these to broadcast the SSID even users get ephemeral could.

  What is the problem?

  What I have to do to put the SSID the same serv access points?

  Thank you

  Likely your APs higher tower to the other. Do a search on the forums for survey site and you meet several good conversations.

• LAPN300 - the best configuration for 3 access points, while using the same SSID

  Hi all

  What is the best configuration for 3 x LAPN300 located in various places around my house of 3 floors, access points if I want just one SSID?

  I did some initial research which suggests that I can use the same SSID on all three, as long as they are on different channels. 1, 6 and 11 for example. In theory, then, as I wander around the House the client machine must auto swap to the AP with the signal stronger.

  What do you think? What is the best way or do, or could suggest you something else?

  As an aside... If I decided to create a second SSID for the guests at home, I would also want to add wireless isolation to this SSID. How would that be managing the DHCP server on the local network? How would be asked to connect to the SSID has never get an IP if they have been isolated from other clients on the local network?  Besides, how they see the router? The ANNUAL lets you specify exceptions to this isolation for this feature?  Alternatively, as I suspect, is the right isolation feature isolate them from other WLAN, not the LAN clients customers?

  I did some testing and configuration of the AP with the same SSID and security will do what you want. Don't worry about setting the channel because the auto channel setting works with these devices and automatically adjusts the spacing between the appropriate channels.

  Recommendation of the VPN_user is what you need if you want to isolate the SSID comments from the rest of your network clients.

  Isolation of SSID of the AP will guard only wireless devices to communicate with each other on the same SSID on which it is enabled.

• the same SSID used on 3 sites and even vlan assignment client IP?

  our 5508 controller and LW APs to IP phone 7925 G wireless

  Controller is installed at A site and there are APs and wireless to the site B and C as well.

  1. can I use the same SSID for the three sites for cordless phones? or having to use separate SSID 3?

  2. If I use the same SSID, can I associate a subnet for example 10.10.131.0/24 for the 3 sites Cordless IP phones? (our UCM Cisco is fine with that)

  3. If I use 3 distinct SSID, must I give three subnets for IP phones on three sites?

  Thanks for the help!

  Eric

  Yes you are right... but its recommended to configure HREAP for remote offices... so that the failure will be less compared to the AP in local mode...

  Let me know if that answers your question...

  Concerning

  Surendra

• my iphone 4S has lost carrier no service modernized 9.3.5 software but my other 4 s with the same carrier is very well after upgrade

  my iphone 4S has lost carrier no service modernized 9.3.5 software but my other 4 s with the same carrier is very well after upgrade

  Hi rog247,

  Thanks for posting here in Support of Apple communities! After reading your post, I see that your iPhone 4S shows 'No Service'. It is certainly important to have access to mobile data; I would like to help get this sorted out.

  Please follow the instructions here:
  

  If you see no Service or research

  If you see no Service or search on your device, or cannot connect to a cellular network or cellular data, follow these steps:

  1. Check your coverage area to ensure that you are in an area with a cellular network coverage.
     • If you cannot connect to a cellular network on your iPhone, make sure that the cell data is on in settings > cellular*. On your iPad, go to settings > cellular data.
     • If you travel internationally, make sure that your device is set up for data roaming. Go to settings > cellular > data roaming.
       
  2. Restart your iPhone or iPad.
  3. Looking for a carrier settings update.
  4. Update your iPhone or iPad to the latest version of iOS.
  5. Remove the SIM card and put it again. If the SIM card is damaged, or does not fit in the drawer of the SIM card, contact your carrier.
  6. Reset your network settings. Tap Settings > general > reset > reset network settings. This also resets the Wi - Fi networks and passwords, cell parameters and VPN and APN settings you used before.
  7. If you have another device, see if you can connect your business with her network to this place.
  8. Contact your operator for:
     • Make sure your account is active and in good and due form.
     • Make sure that there are no failures in your area.
     • Verify that your device is not blocked to receive cellular services and is set up with the right data plan.

  If you still cannot connect to a cellular network and have confirmed with your carrier is not a problem with your account, or your network, try to restore your device.

  If you cannot connect to a cellular network or cellular data - Apple Support

  See you soon!

• Apple Watch series 2 comes with the same battery life?

  ddoes Apple Watch series 2 come with the same autonomy and 18 hours without sleep tracker device?

  Hello

  Yes - Apple Watch series 2 offers up to 18 hours of battery life.

  Follow-up sleep was not announced as a new built-in feature.

• Multiple images with the same file name no doubt prevent export

  iMac running OS X El Capitan v10.11.6; Photos 1.5

  I'm trying to export approximately 331 images and I get an error report saying that only 169 of the exported images due to the inability to create files for 159 of the images.  Then the report gives me the names of files of the first 100 images for which files were not created.  After looking at many images that would not create a file, I realized that, in any case, there was at least one, if not several, other images with the SAME EXACT FILE name as the image in question.  I can't change the names of files by right click on "info".  I tried to export the images and change the names of files to export using the sequential option and the option of album name - always having exactly the same problem.  I even tried not to export an image at once and change the name of the file individually or no available. Is there a work around that? I desperately need to export those specific images. I am trying to create a photo album for shown to mothers who choose a family with which you want to place their child/ren for adoption. I'm at my wit's end.  The kicker is I'm moving towards trying to export all my pictures, and that's going to be a HUGE problem in course for me, so I really hope that there is a way around this question somewhat simply. I am a hobby photographer and use the computer for businesses and crafts.  I've seen a few posts that included answers referencing "AppleScript" - I have no idea how to do something like that.

  From here on I will DEFINITELY ensure that my Canon continually numbers the names of image files and automatically resets.  For the other photos other than Canon, is possible to rename images during the import of the lot?

  All advice and help will be GREATLY appreciated!

  Finder has the ability to rename files with various models of lot.  Simply select all the files to rename, right-click one of the selected files, choose 'Rename X points... '. ", and then set the options and click on the button"Rename ".

• Mac Air 1.3 Ghz i5, 4 GB ram end of 2013 everyone upgraded to El Capitan with the same configuration?

  worried about the going 10.10.5 Yosemite to El Capitan. Especially with only 4 GB of ram. Have 256 GB SSD HARD drive

  would appreciate an answer from people already have the upgrade.problems with the same configuration? slower?

  FWIW, the El Capitan applications are no different from Yosemite. In fact, it is easier on resources in some areas. The main thing you need to worry is to make sure the software and equipment to use is compatible. Make sure you have a good backup in case you change your mind and want to downgrade.

• How can I restart firefox with the same tabs and windows?

  How can I restart firefox with the same tabs and windows?

  It is not in the file menu or tools. I get nothing when searching for help. FF still knows how to do it, say to update extensions.

  I know that I can do by saving my session, coming out, reboot and restore the session but is there a single command to do this?

  Thank you. -David

  I have attached a screenshot showing how to select restore automatic session just above the setting of the Home Page where it says "When Firefox starts".

  With this set, you can restart Firefox manually out using the menu-

  • "3-bar" menu button > button "power".
  • (menu bar) File > Exit

  -and then restart Firefox.

  If you want a real reboot with a click of button, you can check something on the Add-ons site: https://addons.mozilla.org/firefox/

• IMessage Apple Watch has two interviews separated with the same person?

  My new Apple Watch has a problem with iMessage and I know how to fix this on my iPhone but not watch?

  On my iPhone, that my ID apple is connected to more than 10 devices and sometimes when a new device is added, it adds the addresses on my apple for iMessage and FaceTime ID and I always fix by unchecking the addresses that I don't want in the application settings under "Messages" and "FaceTime." However, this isn't the same thing to watch because there is no option in the settings on the Apple Watch and the watch App on my iPhone.

  I would like to help please?

  Hello

  Apple Watch uses the same parameters (for how you can be reached and how new conversations are started) for Messages as your iPhone.

  If you have two interviews separated with the same person, the following steps may help:

  • On your iPhone, check if there is more than one contact form in Contacts of this person (if so, remove duplicates).
  • Delete old Messages conversations with this contact on each of your iPhone and watch:
    • iPhone: app Messages > swipe to the left on a message thread > delete.
    • View: Open the Messages app (from the home screen, which is accessible by pressing the digital Crown) > swipe to the left on a message thread > tap on Trash / delete.
  • On your iPhone in the app Watch: Watch My > general > reset > press reset sync data:
    • You won't see anything happen after pressing it (the process runs in the background, invisible to the user).
    • Leave a minute or two to allow the course ends.
  • Restart your iPhone and your watch (turn the two together off the coast, then restart your iPhone first):
    • Restart your iPhone, iPad or iPod touch - Apple Support

    • Restart your Apple Watch - Apple Support