2545 HP printer all in one: printing problems.

Similar Questions

• HP deskjet all-in-one 3632: problems to make eprint to work

  OK, I'm having a problem making the printer to connect to the internet.

  I have a static IP address on my ISP.   I have 1 n600 Router 2 broadcasting networks.  1 5 g and 2 1. 4 g.   I used void net default 192.168.1.1 and 255.255.255.0.   This router I have a win 7 64 home computer hard wired. I also have a hard wired my Office Access point. the access point also broadcast a GIS of different 2.4 g.  all the sig.s wireless use wap2 Protocol and b/g catch up mode. and the names of all different but same network total network, if that makes sense.  OK, I have a total of 4 more also attached computer too either or network win7 32 ultimate win 7 64 and win vista 32. 2 tablets and 3 IH smrt 5.01 lolipop android running.  I have 2 security cams that have a static for IP and port forwarding on them.  everything works fine.  all computers are part of the same private network hmegroup.  I assigned a static ip address for printer dhcp table.  I can print from any device at any time via wifi.  NOW HERE'S THE PROBLEM.  whenever I go to the WEB form, he is saying that its not active all the check boxes and I don't know what a proxy server is but I know that I have not installed on this network so I click No proxy server.  The PRINTER SAYS UNABLE to CONNECT to the INTERNET.  every time that I tried about 20 this weekend.  It says to check the dns, gateway, blah blah blah.  so the DNS are correct and it shows not 192.168.1.1 as the gateway.  He also btw autodetected it correctly.  so when it fails to connect, I click on web print report. I get the page "get the most out of your printer.  and then a white page. and that's all.  at the top of the page to "get the most out of your printer" it says in "BOLD", "your printer is not connected to a network" which is BS do see on every device and every computer wireless or hard-wire. and I open it a new browser window using 192.168.1.143 which is the static ip address for this printer and bam. It opens right.

  When have I forgotten?  can I configure the gateway as the ip of the real gateway side the ISP of my router.   Im a little aggravated because the only reason why I got this printer from walmart that the PHN android already had the makings of plugin hp on them and I don't like HP is cause of all the fluff sofware that comes with them.  I almost had a gun, but they seem fragile and plasticy more than this one does.  so as I said work is expected for printing on the web.  I tried to press the eprint button and it flashes a little and nothing. I pressed it and the 'i' button and nothing ever prints other than the above page.  I have reset to the default values and done everything as configuration 2 x.

  If anyone can help, I would be very happy.

  facorbin

  Hey @Facorbin,

  Welcome to the Forum from HP Support.

  I see that you are unable to activate the webservices in the all-in-one printer HP Deskjet 3632. I want to help you with this. I have some suggestions that might help.

  I recommend you try the following steps:

  • Enter the IP address in a web browser , and press Enter to go directly to this page. This should take you to your built-in Web server (EWS) printer.
  • Click the network tab.
  • In the submenu on the left, click Networking.
  • Then click on the network (IP) address.
  • Click Manual DNS server.
  • DNS preferred as 8.8.8.8 manual entry
  • Auxiliary DNS server entry as 8.8.4.4
  • Click on apply to finalize this change.
  • Note that menu above EWS items can vary in overall models of printers. If you do not see the exact topics that I've listed here, the subtopic you should always appear on the Networking tab.

  If this goes through successfully, try to activate the web services () again. If you're still coming up short after this point, I recommend you enable DMZ mode in EWS your router, manually add the IP address of your printer. (Based on the level of detail, I suppose you're a statement you know what that means). After completing this step try to enable Web services one last time. Success?

  Please let me know the result of your troubleshooting by responding to this post. If I helped you to solve the problem and that you liked this post, feel free to express your thanks by clicking the "Thumbs Up" icon below by clicking on "Accept as Solution" (this will help others find the solution).

  Thanks for posting in the Forum from HP Support.

  Have a great day!

• HP Officejet 6700: HP Officejet 6700 Premium all in one network problems

  Printer = printer HP e-all-in-one Officejet 6700 Premium
  Model = H711n
  Number of product = CN538A
  Firmware version = MPM5CN1450AR
  Location = Ireland
  Printed pages total: 152
  Scanned pages: 58

  Other details available on request...

  I've had this printer for several months now, I have had no problem connecting to my wireless network and connect computers, telephones and other equipment to this.

  A few days earlier, when starting the printer display flashes with the useless error message, error in the printer, turn the printer off and back on.

  I have power cycled as requested and received the same message, over the power of the cycle he mentions turning off the power button and no DISCONNECT of the sector. Until then I had never disconnected from the sector. After that I have several attempts to power cycle the printer is off and removed the sector, has waited half an hour and powered on again once.

  Still stuck in a loop. He also briefly flashed a blue screen with the error B81431CB. So brief that it is almost useless. I had the boot sequence video and pause playback to read error!

  After some research, I decided that she was experiencing problems connecting to the WIFI network. So, I turned the wifi on the router and the printer network started as usual. Internal menus are now available and I can print status and so forth, so at this point I can exclude defects of ink or mechanism.

  I went in on the printer network settings and reset the network. I'll also through the printer to factory default settings. I have reactivated the WIFI network to the router then went to install the printer again. Digitized for wifi networks and found mine. Entered the password for wifi and the printer could not connect. Everything is good, correct ssid, signal. Report shows wifi password is incorrect.

  I have try several times to connect wifi password is certainly correct, but the printer refuses to recognize the correct password. I tried a different router, the same result. Says incorrect password. Also I tried WPS and a PIN, said still fails to connect.

  At this point, I have disabled all security on the wifi network. Bingo, printer connects to the network, but starts with the loop of error mentioned at the start of the tour and turn it back on. This above has been tried several times, the factory reset, everything ok, turn off the wifi security, the printer connects and goes in a loop.

  So, at this point wifi is confirmed to be defective. I decide to directly connect a LAN cable. Once the LAN cable is connected, a few seconds later the printer detects the network and goes back into its loop error. It will not just connect to a network via wifi or LAN. He previously worked on the network, and nothing has changed on the network, not new parameters or no new devices.

  I connected a laptop to the printer via USB and that seems to work ok, but a USB connection is not ideal and defeated the convenience of a wireless printer. I also tried to reflash the printer in case there is a corruption of the firmware, but the utility detects that the latest firmware is installed and that it is not engaged.

  Now...?

  OK I managed to make it work and I will try to explain the steps of my best.

  As mentioned previously, I tried another router, I tried the wiring, and I tried to reset the router and the printer. Nothing seemed to work.

  Out of curiosity I just put my phone in a WIFI AP. Tried connecting the printer and it worked. The printer connected to the WIFI phones.

  So I know that the printer works on at least one access point.

  Thus, in the settings of the router and firewall. The only thing enabled in the firewall have been

  IPv4 firewall protection

• HP Officejet 4355 all-in-one: scanning problems

  The Scan option does not appear on my computer despite having installed the all-in-one HP Officejet 4355 printer. I also tried to download the latest drivers for the printer but the Scanner does not work. Yet on other laptops (I have a Gateway laptop), there is no problem, the analysis option is available.

  Is there a compatibility issue when using the printer on Vista?

  Hello

  Please download and run the HP print and Scan Doctor www.hp.com/go/tools

• Software for 2540 all-in-one installation problem

  Try to install the s/w for the all in one 2540 on an asus laptop running windows 8.1 64 bit. I get the error message c:\program 5 HP HP desk jet 2540 series\driverstore\yeti\hpvyt11.tnf install a driver package caller must be a member of the management group to install a driver package. As I am the only user on the laptop the full administrator rights so I do not understand what is happening

  Hi @Fish66,

  Welcome to the HP Forums!

  I see that you have a problem installing the software for your HP Deskjet 2540 on your Windows 8.1. I'm happy to help with this installation problem!

  To get help, I'll have to know the following:

  • If the printer is connected, wireless, or USB.
  • If the printer is able to make copies. Copy the text or mixed Documents.

  In the meantime, try the following:

  • Uninstall the software. Uninstalling the printer software. (In case it has been partially installed).
  • Clean boot the computer. How to perform a boot in Windows.
  • Re-install with the HP printer install wizard for Windows.

  Hope this helps, and hope to hear from you soon!

• HP Photosmart 2713 all-in-one scanning problem

  Hello

  I have a HP Photosmart 2713 all-in-one and installed OSX Mavericks. My print function works fine through "Printers & Scanners" in system preferences, however, I can't scan from this application.

  I tried to find software to download HP Scan that I didn't do it, but can't find the software for my printer/scanner.

  I also tried the other methods described for example by trying to browse an excerpt and the other options, but nothing has worked.

  Thank you

  Saami

  Hi SamiAR,

  Welcome to the Forums of HP's Support. I apologize for the delay in responding to your messages.

  The last driver full features for your Photosmart 2713 on Mac was for Mac OS X 10.6 Snow Leopard. I have included a document on the installation and use of the printer with Mac OS X 10.9 Mavericks.  I have also included a document on scanning with the Mavericks.

  V10.9 OS X Mavericks: installing and using the printer on a Mac

  http://support.HP.com/us-en/document/c03967522

  How to perform a scan: OS X v10.9

  http://support.HP.com/us-en/document/c03967506

• HP C7280 all in one. Problem copying

  HP C7280 all in one.  During the copy with the original on the glass, the copy is fine.  During the copy with the original introduced in the extra paper tray, a vertical line appears at the same place on each copy of the product.  Maybe some soil is at this location on the device that "reads" the original document because it passes?  Any suggestions on how to get and check this out?

  Hello

  I would tell you to follow the steps mentioned the link and check if this helps out you

  http://support.HP.com/us-en/document/c00899181

  Thank you

  I am an employee of HP, these messages are consistent with my knowledge and HP is not responsible.
  By clicking on the star of congratulations in the post helped you to say thanks.
  Please indicate the position that solved your problem as accepted Solution

• HP all-in-one 5610 model: All in One 5610, problem loading new software for Windows 8.1

  Hi, just bought new HP computer with 8.1 widows, my all-in-one 5610 has been working fine on the old Windows XP.  Installation of new software 8.1 system HP I get unknown device (configuration descriptor request failed). As for the USB controller get Windows has stopped this device because it has reported problems Code 43. Thnks for any help you can give.

  Hi @Joe62 and welcome to the Forums of HP!

  I understand that you get code 43 error. I'd be happy to help you!

  I recommend to check this page from Microsoft on Code 43: Windows has stopped this device because it has reported problems.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• DeskJet 3050 all in one connection problems

  I have a 3050 all in one deskjet, I can't keep it connected to the computer, I have reinstalled several times, but I I can never find it on the computer

  Hello

  Please specify your operating system.

  In addition, you use the device with a USB connection or via the network?

• ENVY5530 e-all-in-one:. Problem of the printer (ENVY5530 e-all-in-one) with a sweep

  I have a problem I scan a document to an email.  The States of "Server connection error" messages and "there was a problem connecting to the server.   There is no further explanation or any indication as to what to do to fix.   I have never had a problem with scanning and don't have an idea why this is happening and the system does not.   Have tried rebooting the computer, I get the same error message.   Any ideas?   Thank you.

  Hey @Laylac,

  I understand that you have problems with the help of e-mail scanning on your 5530 desire. I can help with that. To correct this:

  1. On the printer, click Web Services icon in the upper left corner of the screen. It looks like a tablet with a phone beside her.
  2. Click settings.
  3. Scroll and click on remove Web Services.
  4. Once back on the main screen, click the Web Services again.
  5. Click on accept.
  6. Click Yes.
  7. Try scanning to E-mail.

  If you use ePrint to the printer, then you will need to add the printer to your HP connected account. Once you have signed in, click on the devices tab, and then add a device.

  If you have any other questions please let me know. Even if this assistance then please let others know by clicking on accept as Solution below my post.

  I hope this helps and I hope you have a nice day!

• All in one Photosmart - problems with the re - C309a install.

  Hello

  For the above, I, a Windows 7, 64-bit computer. I tried to reinstall the printer, but whenever he asks me to re - start the computer as some files should always be deleted. Once the computer is restarted, then the software starts the Setup program and install, but it gest to the point to repeat once again the message above need to reboot to remove some files pending and so on.  This creates an endless loop that never installs the software.

  Any ideas?

  I'm sorry you have a problem with the drivers.

  Try a couple of different steps of uninstall.

  1. click on Start Menu

  2. Select all programs

  3 right CLICK on COMPUTER

  4. choose MANAGE

  5. go under the tabs (image and devices and printers).

  6. If the printer is on any tab, right-click top, and UNINSTALL

  Also try clicking on the start menu

  1. choose all programs

  2. Select HP files

  3. choose the name of the printer

  4. click on uninstall

  Let me know if this uninstall all printer software.

• OfficeJet 6100 HP all-in-one / fax problems

  OK, I went through the whole upward.  However, I never see a fax on the Director icon, and when I try to set up the fax settings, all I get is an error message.  I'm so frustrated.  I try to send a test fax for Kinko's, and I continue to be told that it does not.  Obviously, I'm doing something wrong.  I am an elderly woman of 72 years with no about 8 year old boy to assist me.  Help! someone please help me.  Thank you.

  Well, it of always the simple things, isn't it.  Finally, I realized that I had the phone jacks into the slots on the printer hard! Had the phone connected to the one slot and the wall jack to the slot two, which, of course, should be just the opposite.  The minute I put them where there should be, has worked beautifuly fax.

• Mac / Photosmart C6280 all-in-one / scanning problem

  Help! I had to have my i drive hard mac replaced. I reinstalled my printer 5 times now and the scanner does not work. After the installation of the 2nd, he did scan... I then mucked with the photo and decided to rescan instead of the photo to accept it. From there on, I get a message telling me in HP Device Manager... "Sorry, an unknown error has occurred" instead of scanning, or if I click on the printer, then scan, it says not to scan selected... with none even for the selection. If I go to JPEG in hpphotosmart studio on printer, no computer, he sends to the Device Manager, scanning through, and give me back the sorry unknown error occurred the messge. At other times... I completely lose the option scan to computer... the printer. I tried updates... He sits for hours with nothing to do. I hope I can find an answer! It is out of warranty.

  OK, you don't need the HP software with 10.6.  In fact, if you have loaded it from the CD that is the problem (this is for 10.5 and earlier only).  We will do this:

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt Cmd and click on uninstall
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Now run a software update.

  Then, remove and reinstall the printer in System Preferences, Print & Fax.

  You do not have the software now since Snow Leopard as well print & scan drivers built-in. scan from Preview apps or Image Capture. Scan from the front panel of the printer does not work yet.

• 7520 photosmart all-in-One: sudden problem connecting to web services

  I used my HP Photosmart 7520 years without problem scanning to e-mail. Now I get "Unable to connect to Web Services" error message. I also have a server connection error appear together try to print selections on the screen of the printer - such as the activities of crossword puzzles, sudoku and children.  How can I fix it.

  Hello

  From the Configuration menu, select Web Services Configuration.

  Select Delete Web Services and confirm any command prompt.

  Now re - open the Apps option and follow the steps to reactivate Web Services.

  Once you're done open the scanning to Email application and follow the steps to reactivate Web Services.

  Provide your own e-mail address, and then type the PIN Code received in your email address and try scanning.

  Kind regards

  Shlomi

• OfficeJet 7210 all-in-one duplex problem

  Since the Officejet 7210 connection to laptop running Vista Business, printing accessory 2 sides with rear tray is not recognized. I have been using the 990c for 2-sided Deskjet driver but it does not recognize the quarterdeck. Impossible to print photos using the quarterdeck, and when I try to load the photo paper 4 x 6 in the main tray, the image will print to the position of the center of an A4 page, not the location when the tray is adjusted to 4 x 6 (10 x 15 cm) stock AM. How can I activate the rear tray feed stock photo.

  Is there an updated driver for the 7210 that supports the duplexer with rear tray or what other solution would you recommend?

  Given that the duplexer and the rear tray were optional on the Officejet 7210 the default driver for them being "not installed".  Go to the printers, right click on device settings 7210, folder properties, Installation Options, and set the duplex unit and the rear tray installed, apply, OK.

  This makes the rear must be accessible and you can try duplex printing.  You will probably need a patch to correct the print head back down when printing double-sided, it is available as described here.

  Kind regards

  Bob Headrick, MS MVP printing/imaging

• 2210 all-in-One: alignment problem

  My 2210 poster constantly "press ENTER to align cartridges". When I press Enter, it don't alignment and prints, but then continued the message of alignment. I can't stop the message. I tried power off and reset a partial, but nothing helped.

  Look at the area inside the front of the printer as the alignment procedure. You should see a blue light below the cartridges when they move back. If you don't see the blue light, alignment fails, it's probably why you are prompted to perform the alignment repeatedly.

  If you don't see the blue light, the printer must be repaired.

  If you don't see the blue light, perhaps that the cartridges can not be aligned. Try to remove and reinstall and see if alignment after reinstall the cartridges.