2560 P temperature range: 2560P

Similar Questions

• after update of Lightroom, to develop pictures in the temperature range

  after update of Lightroom, photos to develop are reflected in the temperature range!

  Hello

  • Go to Lightroom > Preferences
  • Also please go to preferences > Performance tab and uncheck the box "use graphics processor.
  • Restart Lightroom and see if it works.

  Concerning

  Tanuj

• I7-920 CPU temperatures range between 54 ° C and 100 ° C.

  Hello.

  I hope someone can advise me here.

  My hearts of the i7-920 processor reached during the analysis of my PC with Windows 7, Microsoft Security Essentials, the following temperatures without running other applications.

  

  My BIOS showed the following readings.

  Discount on zero case status open	[Disabled]
  Case opened	Yes
  VCore	1.252V
  DDR15V	1.536V
  + 3, 3V	3.296V
  + 5V	5.080V
  + 12V	12.112V
  The current system temperature	41 ° C.
  Temperature identified	92 ° C
  Current temperature of health maternal and child	48 ° C.
  Current CPU FAN speed	2368 RPM
  Current speed of FAN2 SYSTEM	0 RPM
  The current ELECTRIC FAN speed	2636 RPM
  Course SYSTEM FAN1 speed	3426 RPM

  My PC has 6 fans:

  1 fan on the CPU cooler intel standard.

  1 fan at the top of the case,

  1 fan on the back of the case,

  1 fan on the front of the case to 5 hard drives,

  1 the power supply fan, and

  1 fan on the graphics card.

  They are all clean and running.

  With only currently running Firefox, my CPU temperature readings are as follows.

  

  Should I be concerned about these temperatures?

  Yes.

  Cooling is quite inadequate. Time slowed by the 920 stock speed should not be more than around 30-35 degrees C and under load not more than 65 degrees. Stock cooler can add a few degrees, because he is not good at all, but there is also an insufficient air flow in the case of cause these absurd time. It is very detrimental to the longevity of the CPU.

  I suggest that you get a good third-party CPU cooler with push-pull configuration, like CoolerMaster, Noctua or Prolimatech and good thermal paste, correct the internal airflow with cable management good or get a larger case. Report your progress.

• What is the range of temperature for the 9219 and 9211 measurement modules using a K type thermocouple as the sensor?

  Hello

  hope I posted in the right place. I'm about ready to buy a cDAQ-9172 chassis and modules temperature 9211 or 9219 universal. I have not yet taken my mind yet. Then, I thought that one of them would make the temperature range required that I need. I need to go from-40 ° C to + 200 ° C and I will use a K type thermocouple. Does anyone know what are these upper and lower limits with this configuration?

  Thank you

  Mike

  9211 entry record indicates the tension... measuring range ± 80 mV

   

  A quick check on Omega web page http://www.omega.com/temperature/z/pdf/z204-206.pdf indicates this combination will be easilly cover your range of operation.

   

• Portege M400 - temperature?

  I have a Portege M400 under XP SP2 and during normal use, the temperature is usually between 55 and 65 degrees celcius. To load, the temperature is consistently above 60 degrees, between 60 and 75 degrees celsius.
  I was wondering if this is a normal temperature range - or maybe I was so unlucky as to have gotten a defective processor.

  Jonas

  Hello

  I'm sure you know that the CPU temperature is based on the use of the processor and also the position of the portable computer (on the desktop or on the knees) and how the device can be cooled.

  In my opinion there is no reason to worry. Now while typing this message and listen the the CPU temperature online radio (no activity) is 63 degrees Celsius.

  In any case, I recommend you to update the BIOS on your device. I put t know if you have any info of saw on new update BIOS for M400 under http://support.toshiba-tro.de/kb0/TSB6A01KJ0000R01.htm

• Re: Room Temperature for Satellite A100-999

  Hi all

  I have a Toshiba Satellite A100-999 (old lil :/) with XP

  I was wondering what are the temperature ranges at low, medium or high performance for the motherboard and CPU.

  at the present time about the temperature I have are: (Celsius)
  Motherboard: 60 + -.
  CPU: 65 years and more-

  When it has a high performance, it reached 90 - 95 +-. And if im right... the CPU with this temperature control can be activated automatically right?
  As im not an expert in the field, can someone guide me a bit?

  From now to detect temperatures im using the software: Everest AIDA64. (I guess that temperatures are not 100% Reliable, but they give me an idea).
  If there are ways to cool the laptop (I know cleaning is one of them of course) I would be grateful to receive some information.

  Thanks in advance

  concerning

  > I was wondering what are the temperature ranges at low, medium or high performance for the motherboard and CPU.

  It is not easy to say dude. The temperature can be always different and always depends on the use of the laptop.
  On the Intel page, you will find details about your CPU and you can find the temperature for the CPU limit. It s mainly around 100 C.

  However, if the temperature is too high, then the laptop would shut down automatically to prevent the equipment from damage. If the laptop is secure with such protection.

  By the way; the temperature can occur at a higher value if cooling modules and grids are obstructed by dust. So it s advisable to clean the grilles and fans of compressed air for usinf time spraying time.

• What temperature is essential - Satellite A100-411

  Hello

  I use my laptop for DJing and a stop would be terrible on a concert.
  I installed speedfan on my Satellite A100-411 and when I was in her setting, I was wondering, what temperature would be critical, causing a cpu stop or other errors.

  SpeedFan is followed by three CPU (Core Duo T2250), HD (Hitachi Travelstar) and GPU (GeForce 7600) temperatures.
  It would be great to know what are the maximum temperatures of security of each of the components of this.

  Sincerely,
  DJ Hondai

  Hello

  Unfortunately, I n t think that Toshiba provides such information in any other public document.
  I found in the user manual that the requirements of the environment and the laptop should be used in the temperature range of 5 to 35 ° C.
  But there is nothing about the temperature of the single components.

  You can try to check the Intel website for details of the CPU and possibly it you will find information on critical operating temperature.

• Satellite L850-046 - question about the CPU temperature

  Hi Experts,

  I bought the Toshiba laptop 9 months ago, but now notice the temperature warms. I check the software Toshiba Health Monitor and the CPU temperature range of 46 to 53%, fan speed 50%-63%.

  Is - this normal readings?

  I am now using a desk fan pointing in the vents hoping that additional traffic can maintain better temperatures.

  What would be the ideal and the overheating of the readings to look out for.

  Thank you very much

  Because cell phone use for 9 months, I recommend you to clean the cooling fans.
  The fact is that from time to time the dust and debris that may affect the performance of the cooling fans, and this could lead to a higher temperature.

  I clean my fans from time to time using a jet of compressed air.
  It helps to get rid of dust and to lower the temperature.

• Portege 3500 operating temperature?

  Hello

  My Portege 3500 crashes regularly (the monitor continues to show what was the last one on the screen, but no entry is accepted, not even ctrl-alt-del) I have to hold in the power button until the laptop turns off to restart. I think that this could be due to overheating and try to check it out using speedfan to monitor temperatures.

  Does anyone know what temperature ranges are acceptable for the 3 temperature gauges that speedfan reports (Temp Local, remote Temp and Temp1)?

  Thank you
  -Jason.

  It's not easy to say what temperature is acceptable. On my laptop, I recorded about 60 ° C and everything run ok.
  I assume you are using unit for a long time as well as the fans have not been cleaned.
  You can try to do. But be careful. If you have no experience, you shouldn't have t do.
  Additional you should always be sure that there is enough free space around the laptop for cool air circulation.

  PS: you may install the Everest application. This tool provides a lot of information on the entire system.
  After cleaning, you can compare the temporary values

• Where can I find what should be my temperatures of the CPU for laptop HP Pavilion DV7-6195us?

  I download a software to view the inside temperatures and even if they have little symbols (green check, red/yellow flame, etc.) by every internal part (e.g. CPU0) I want to know what HP internal temperature range is recommended.  Thank you.

  What CPU is installed in your laptop?

  It isn't really a question of what HP is recommended. Your concern should be what the CPU manufacturer lists as Tjunction for the CPU.

  If your laptop is the Intel Core i7-2630QM installed then lists Intel 100 c as TJunction. I found the technique for your laptop here. You should be concerned if you see time > 85 degrees Celsius. Here is a link to Intel for your processor plug.

• My t420s runs at a normal temperature?

  I just bought a used thinkpad t420s and I was wondering if it is overheating or running at the right temperature. The CPU is idling in the middle to low 50 (degrees Celsius) and will reach 95 degrees Celsius 95 premium running. When running a virus scan and watch a video YouTube the chip works in the high 80s. Is this normal? According to Intel, the max temp allowed is 100 degrees Celsius. I have all the power settings for maximum performance. Here is a link to my http://ark.intel.com/products/52231/Intel-Core-i7-2620M-Processor-4M-Cache-up-to-3_40-GHz chip

  I could mention that using TPFC.63 I always get the top fan then the bios will control them, so I think the TEPS is normal, because bios would probably spooler fans at full power if the system was about to stop from overheating.

  Hi Daniel250,

  Welcome to Lenovo Community!

  According to the application, we realized that the problem with the system is overheating on your ThinkPad T420s.

  The normal temperature of 72 degrees centigrade CPU and GPU at 68 degrees centigrade is in the safe temperature range.

  If you feel that your laptop is hotter than usual, clean the vents and fan through the use of a fan pump to remove dust particles stuck in vents and it also perhaps with thermal paste between your radiator and the processor core can have exhausted. You might want to make a good thermal paste and apply on the processor core to ensure the best heat transfer property

  I hope this helps.

  Best regards

  Agnes Kumar

• guidance inertia temperature control

  Dear people,

  I would ask for advice from experienced people in control theory.

  Recently, I'm working on a very interesting device, it is called inertial guidance vacuum calorimeter (there is a type of isothermal calorimeter). I'm doing a new LabView program for this camera, and I try to increase its stability/accuracy as much as I can. This calorimeter can measure heat sample level micro-watt powers. The principle of measurement is the following (see attached diagram):

  We want to measure the heat flowing from the outside door-sample, this is done via Peltier (thermoelectric sensor) sensor. To obtain valid data, temperature must be very precisely constant everywhere in the calorimeter (isothermal method). The inner parts of the calorimeter thermally protected against ambient temperature with blank shields and high radiation. Double room empty closed circulates water through a heat exchanger, the heat reservoir.

  For thermal stability, there are 3 loops controlled:

  1 control loop. : this controls using PID, (method of classic platinum resistance 4W) constant water temperature

  2 control loop. : this is the first step to stabilize the temperature of the inner part, PID loop classic platinum resistance and drives a pump to Peltier heat between the support and the "base". This can achieve only a constancy of temperature around 0.1 mK.

  3 control loop. : when the ultimate stability is reached with the control loop 2, it is off, and his conduct of the current production constant value. Now the loop3 begins, and that's the tricky part: there is a cylindrical copper heavy 'inertial mass' with high calorific value (much higher then the base) standing on the base. Because it has a high calorific, even temperature fluctuations very tiny in the performance of temperature-controlled database a measurable voltage in the thermoelectric sensor between inertial mass and the base. This value is measured by the meter nanovoltage (Keithley). So I use this value to control the heat under the base pumps.  In principle, if there is no heat flowing between inertial mass and the base, we are in thermal equilibrium.

  With this concept, it is possible the stability of temperature range well below nanokelvins!

  Recently, I play with the control settings, but only using simple PID controls (I have the PID toolkit). The method explained above is a kind of analogy of inertial guidance in mechanical control. I wonder if someone could give me advice or direction how I could further improve the stability of this control. Perhaps some more advanced control system? Feed-forward?

  Thank you very much for the advice,

  Kind regards

  If I follow correctly, the feedback control loop 3 is measured using the Keithley via GPIB.  And these readings take approximately 0.6 seconds. The control loop cannot work faster than the measurement system (unless you want a lot more unstable!).  Most high precision instruments offer a compromise between resolution and speed.  I took a look at the profile of 2182 and it seems you may have need of any resolution, so accelerate may not be an option.

  The approach of bottle neck is probably a good with all that you have done so far.  It will help you to avoid putting too much time into something that won't make much improvement.

  Another thought: how noisy/drifty are power supplies/amplifiers driving Peltier devices?  I worked on a system several years ago, where the objective was stability uK ~ 10 and noise and drift in the power circuits were the main limitations.  Most of the engineers designing such devices never think of parts per million or fractions.  Especially with the slow return of nanovoltmeter, drift or noise in the power circuts could be important.  Also look at how the constant output mode that the external loops are open loop constantly.

  Lynn

• USB NI 9211 measurement range has

  Hi all

  I would like to know if there is someone who can confirm the measuring range of temperature of the case NOR USB 9211 a

  thermocouples of using the en J and K?

  Kind regards

  Hello

  9211 a USB device works on the normal defined temperature ranges the NIST (J, K, R, S, T, N, E, B and types of thermocouples)

  Please open the link below

  Thermocouple NIST database

  Kind regards

  Mart G

• Temperature of ThinkPad T520

  What is the temperature range of security for the T520 (or similar/all laptops?) I received my a week ago and remember all the components to idle at 100Fish and going about 120F under load, which I was happy with. Since then, the only thing demanding by the calculation I did with it is play Stalker SoC for about two hours, and the physically demanding thing I've done is walk a few miles with it in my backpack (also new, so I hope not dusty). However, my temperatures have strengthened. [IMG] http://k.min.us/icAVfKUr9.PNG [line] Here's my time with firefox, xchat, speccy and application of wow running update. Why this phenomenon happens, these temperatures are safe, they are normal and what should I do to maintain the health of my laptop? Thank you!

  Thanks for the reply! Well, I checked my power plan and it is 3/4 of the way to maximum performance. I moved it to the middle. I don't know how to check the CPU frequency, though.

  Ed: start wow updater after moving the slider towards the middle and my temperature is much lower. This marking as answer

• Can I use my screen 2560 x 1440 of HDMI port

  Want to m6 for laptop (Intel HD Graphics 4000) Windows 8

  So I try to run my screen 2560 x 1440 ranging from HDMI port on a DVI input on my monitor.  Simply assign a custom resoultion does not seem to work (says it is not supported) noticed that equivalent Dell machines seem to be this pulling on their bulletin boards, wonder if there is a way to do it on the HP

  Hello

  Some intersting discussion in the following link:

  http://communities.Intel.com/thread/30360

  You may need to reduce the refresh rate (which is not recommended) to be able to get a higher resolution.

  Kind regards.