3 laptops different ALL been facing intermittent problems with the USB ports.

Similar Questions

• Automatic update because of problems with the USB ports.

  After an automatic update this morning at 03:00 October 15, 2010 for windows vista, all my USB ports on my laptop have stopped working. Please advice all solutions to locate the update caused the problem.

  This must be a different problem from what I had so...

  In any case, I uninstalled all updates on vista (as opposed to other programs, office, outlook, etc.) and then reinstalled again and everything works fine now... go figure: /.

• Problem with the USB ports, coast and Bluetooth in Satellite A100-237

  Hello, I own a laptop Satellite A100-237 and I have an annoying problem for quite a while now. The two USB ports in the side as well as the Bluetooth device will not work. What is the bluetooth device is it is simply not recognized by the system, as if it wasn't there (it is said the installation of the driver too) while any device I connect to USB ports side does not work either.
  The other two USB ports in the back work very well.

  Hello

  Maybe this two ports are really defective, and there is not much to say. You will get your laptop for repair, or you live with it and use the other two USB ports. Sorry, but I see your ad as a report short and not as some to ask for help.

  Bye and good luck!

• I am facing a problem with the beep.vi. I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound.

  I am facing a problem with the beep.vi.  I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound. Everything works fine except the sound alarm. It gives the table 1 d of type mismatch. I tried to fix this by placing it in a box structure. But it still does not work. If someone could help? Please find attached my VI. Best wishes to all visitors to the Forums of Discussion OR.

  Ihab El-Sayed

  published here: http://forums.ni.com/t5/LabVIEW/Playing-sound-based-on-exceeding-a-threshold-value-1D-array-data/m-p...

• Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

  Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?

  What Mac? (details)

• I am facing a problem with the POWER of ODIN 9.1.0.5, my broker is Indiainfoline, my OS is Vista ultimate, when I login, everytime I get an error 'System Error (10055) (setsockopt)'.

  I am facing a problem with the POWER of ODIN 9.1.0.5, my broker is Indiainfoline, my OS is Vista ultimate, when I login, everytime I get an error 'System Error (10055) (setsockopt)'.

  Check out these links:

  System (10055) error (setsockopt) Solution
  http://www.win7heads.com/software/82898-system-error-10055-setsockopt-solution.html

  ODIN request does not work Windows 7
  http://social.technet.Microsoft.com/forums/en/w7itproappcompat/thread/ddbe30c8-f4c6-4B8F-ac91-85aa07191ea3

• Tablet HP 8 G2 1411: Problems with my USB port on my Tablet

  Problems with my USB port on the Tablet connector. Fees sometimes and sometimes not.

  Hello and welcome to the HP support community!

  Micro USB ports tend to be quite fragile.  A good accidental yank on the cord that connected while can be enough to cause damage.

  If you want to organize repairs, contact HP directly.

  To contact HP directly, click on this link: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  Outside the U.S.: http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
  
  WyreNut

• All in one Photosmart - problems with the re - C309a install.

  Hello

  For the above, I, a Windows 7, 64-bit computer. I tried to reinstall the printer, but whenever he asks me to re - start the computer as some files should always be deleted. Once the computer is restarted, then the software starts the Setup program and install, but it gest to the point to repeat once again the message above need to reboot to remove some files pending and so on.  This creates an endless loop that never installs the software.

  Any ideas?

  I'm sorry you have a problem with the drivers.

  Try a couple of different steps of uninstall.

  1. click on Start Menu

  2. Select all programs

  3 right CLICK on COMPUTER

  4. choose MANAGE

  5. go under the tabs (image and devices and printers).

  6. If the printer is on any tab, right-click top, and UNINSTALL

  Also try clicking on the start menu

  1. choose all programs

  2. Select HP files

  3. choose the name of the printer

  4. click on uninstall

  Let me know if this uninstall all printer software.

• Intermittent problems with the laptop DV6 wireless

  I bought a HP DV6-6145TX about 2 weeks ago and in recent days the wireless connection no longer works.

  That is to say that even though I can ping it does connect to Web sites.  If I continue to clicking Refresh then it will load and then work ok for a few minutes, and then the same problem, website does not again for a minute or two.

  Is this a hardware problem? (I already loaded to the top of the latest Intel drivers wireless off the HP website and tried to disable the bluetooth module).

  Operating system: Windows 7 Home Premium 64-bit

  Hi Paul,.

  Thanks for the tips.

  It did not work.

  However, I found a tip on the web that makes. Essentially had to reset the network with the following settings:

  netsh winsock reset catalog

  netsh int ip reset reset.log

  Hopefully someone else gets help out of this because it has been massively annoying.

  See you soon,.

  Jason.

• Images - facing a problem with the alignment of captivate

  Hello world

  I am using captivate to create e-learning courses for my client. The course was in PPT and slides have been imported into captivate. The process was smooth until the customer asked me to change the size of the canvas. The course includes images as well as on the slides.

  The problem comes here

  1. I can chamge the size of the canvas of 1024 * 768 and 1280 * 800 in the same file? If so, how?

  2. I tried another way of doing this thing. I created the canvas with 1280 * 800 itself. Then, I went back to the old captivate file and copied all the slides and paste it into the new file. But the blades with images have problem (eg. alignment issues produced.). Is it possible to modify these images here himself in captivate so that I can move with arrow keys and mouse to solve the problems of alignment?

  Thank you and best regards

  Vikas

  Please, this is a forum for users and expect to get an answer right away? Myself and other users to be able to spend more than one hour a day, trying to answer questions, but we do that in addition to our normal work and all this for free.

  You can resize a project with changes, the project of the scale. You have the choice of high end everything, which will always lead to a loss of quality. Best result is given when you can keep the aspect ratio, but this isn't the case for you, since you spend report 4/3 16/10 rather unusual.

  Problem is, imported, Powerpoint slides are converted into film slides. This means that you don't have the items separately in Captivate and will not be able to reallocate the as you request your second question.

  Even resizing in Powerpoint will give you a lot of headaches, because of this change the aspect ratio. And that would be the way to go, if you use Captivate as a converter for PPT, that is not the best use of a creative tool at all. A plug-in for PPT is much better suited for this cause (Adobe Presenter, Adobe articulate, iSpring).

  Is to embed the slides present in a Knockout Master slide a possible workaround?

  http://blog.lilybiri.com/create-and-use-a-knockout-master-slide

  Lilybiri

• problem against the USB port

  I have HP Pavilion 2301ax g6. but I'm tired of Windows 8...
  SO today, I install Windows 7 ultimate. ....
  I hv installed all necessary drivers...
  but... then also my USB PORT does not work... 1 port works, but is not another...
  but I m up to tgat sure there must hv sm software problem. .. .my port is good...
  When I plug the mouse, then the Red shot... but mouse doent work...
  
  Please, I beg you. Help me imeadetly. .....
  thnx... Please help me...
  and also provide me win7 ultimate my laptop drivers... HP Pavilion g6-2301ax
  Please...

  Hello:

  You must first install the graphics driver for the model I posted.

  Then, you need to install this software so that the webcam to work.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-117932-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 5275619 & sw_lang =

• "Unknown device" USB Barcode scanner, problem with the USB controller driver?

  Hello

  I need assistance with our Barcode Scanners that doesn't work on our newly purchased computers at HP with Windows7 Pro x 64 operating systems.

  The brand and model of the bar code scanner is:

  Datalogic Heron D130 USB.

  When you connect the scanner to a USB port, Windows will try to install this as a HID, but it takes an unusually long time, about 7-8 seconds, to boot the device and install the drivers and appears as an unknown device in windows "devices and printers" and the hand scanner does not work.

  Sometimes when you move the USB back can I sometimes the scanner at hand to be recognized as an HID device or a Datalogic barcode scanner,

  It works fine until you restart the computer.

  After restart the computer cannot detect the scanner Barcode correctly without re - appears as unknown device.

  I suspect that there is a compatibility problem between barcode scanner and card USB controller on the computers.

  I tried to update all the drivers available on the website www.hp.com and same www.Intel.com (chipset drivers) but nothing has helped to solve this problem

  Tried newly bought barcode scanners and "used" barcode scanners earlier who works on other computers, but the problem remains.

  I found a workaround by connection of bar codes in a USB hub, and then plug the USB hub to the computer.  And leave the USB - hub to take care of the communication with the Barcode Scanner.

  in this case, it takes about 2 seconds for the code scanner barcode to mount correctly in windows under the heading "devices and printers" and then works perfectly, even after a reboot.

  I googled after a response after my problem, but it seems I'm the only one who experience this issue. ?!

  Bought more than 40 computers that I have this problem.

  These were bought at different times with two different for suppliers

  Computer model are the following

  HP ProDesk 1 400 P/N5S21EA

  Specifikations:

  http://WWW8.HP.com/emea_africa/en/products/desktops/product-detail.html?OID=6614160#! tab = specifications

  Does anyone have an idea what could be wrong and how to fix it?

  Thanks in advance

  Sincerely

  Robert T

  Hello

  The problem is not power - related.

  We use passive USB hubs that solves the problemon these computers.

  (it also works with the docks, or if you EliteDisplay E241 HP as we thers a usb hub 2 ports inbulit in monitor that works.)

  The problem lies in the incompatibility between the Intel USB controller and the hand scanner, can be connected to USB 3.0

  When you let another usb-controller support in handshakeing (such as a usb hub), it works.

  Datalogic or Intel would like to acknowledge this error.

  Because none of the big companies want to acknowledge the problem or repair, personally chose to switch to an AMD platform / CPU instead of the Intel and now it works fine!

  We get more performance for your money when AMD is usually less expensive to purchase.

  And because of the poor of Datalogic press where they don't even answer e-mail (their only channel for support)

  I chose to stop using their products. I'm going to use another provider / brand of barcodescanners.

• Tecra A8: Problem with the USB printer connected to the Port Replicator III

  Hi all

  I have a problem with my Tecra A8, year Advanced Port Replicator III and a USB printer. With the printer connected to a USB port on the Port Replicator, I have to wait 2 minutes for printing to start. When it is connected directly to a USB port on the laptop and the laptop disconnected from the Port, printing starts immediately. I have the latest drivers from the Isensys of Canon LBP 2900 installed and Windows Vista professional as the operating system.

  I called the technical support of my country, but her is not recorded similar problems.

  A person with similar problem? Some help would be very appreciated.

  Thanks in advance.

  Hello

  Seems like a strange question... Already done the standard procedure in the event of such errors? :)

  The standard procedure is somehow similar to the following:

  -Update your BIOS
  -Update all the drivers for your machine
  -Update your printer drivers
  -Update your operating system

  If all else fails, then try an another Portrep if available, maybe you need to contact your dealer for an another portrep for the test.

  Something like this should be your way. And then you sucessfully made a TROUBLESHOOTIN´ ;)

  I'd be happy to hear feedback from you on your situation...

  Welcome them

• I have an android Tablet and my usual laptop recognize it when I connect it to the usb port

  my laptop recognizes my usb webcam but not my pc android tab

  Hello

  1. what operating system is installed on the laptop?
  2. do you get any error message when the tab android PC did not get recognized?
   
  
  Method 1: perform the steps from the link below and see if it helps.
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
   
   
  Method 2: Check the tab pc android with another computer and see if it is recognized.
   
   
  Hope this information helps.

• problems with my usb ports

  I recently got my laptop and my mouse stopped working, I originally thought it was just that the mouse was dead. After having bought a new mouse, that he has not yet decided anything, I tested the two mice on my friends laptop and they work fine.  I was wondering if there are any patches, can I do I have tried troubleshooting and that didn't work other than sending to any ideas what I could do?

  Hi cpav0625,

  1. this question comes up with other USB devices also?

  You can try to run the Fixit and check:

  Check out the link:

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.