32-bit of Windows Vista unidentified network

Similar Questions

• Windows Vista - unidentified network Local Access only tried everything please help

  Hello

  I have an Acer Aspire M1610 running Windows Vista Home Premium Service Pack 2 and 2 days ago when I turned it on the internet was not working and it says unidentified network Local access only. I use a wired Ethernet connection. I don't know how it happened as before I had used the computer as usual and the Internet worked very well. I did a lot of research and read a few forum posts about this problem and tried a few solutions but non of them worked. I tried the following:
  (1) disable my firewall and anti-virus who didn't work, I turned their back on immediately.

  2) press Ctrl-Shift-Enter keyboard shortcut to run a command as administrator prompt.  Allow the elevation.

  Type route delete 0.0.0.0 press ENTER.

  Type ipconfig/flushdns press enter

  Restart your computer.

  (3) the internet protocol version 6 clear, disable and enable the thing

  (4) if same Norton software removal tool I had uninstalled the when I got the computer I read that uninstall it by using uninstall windows is not entirely remove it.

  (5) another thing in the command prompt I don't remember exactly what it was, and I can't find the site Web is because I looked so much of.

  (6) I even reset my computer to factory settings and then uninstalled all unnecessary software and trials that come with and used the software again Norton removal tool.

  Does anyone know how to fix this? Any response will be greatly appreciated.

  Thank you

  Hi Alex,

  Have you tried to assign the IP addresses manually?

  I wish that refer you to this article-

  http://support.Microsoft.com/kb/928233/en-us

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  Back up the registry - http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry

  Thank you.

• Printer HP Officejet 4622 on 32-bit of Windows Vista computer

  I need to understand how to change my settings to Windows Vista 64-bit for Windows Vista 32 bit. I accidentally entered my computer as a 64-bit when it is actually 32-bit. If someone could help, I would really appreciate it.

  Hello Kia214

  Unfortunately the Officejet 4622 is not a printer. What explains your problems. Some eprint printer - none can still be printed to locally if you are installing the HP Home & Biz application on your mobile device such as a tablet or cell phone. You can refer to this thread HERE for a complete list of printers that support eprint as well as to the other features they support.

  Here's a FAQ on the HP Home & Biz app.

  Home HP & Biz

• How can I get a 32-bit of Windows Vista in Photoshop version, please?

  How can I get a 32-bit of Windows Vista in Photoshop version, please?

  Hi Kevinhannan,

  No courses Photoshop supports this configuration.

  Photoshop CS5 is the latest version of Photoshop to support Windows Vista.

  Photoshop elements 12 was the latest version of Photoshop Elements to support Vista as well.

  We no longer offer Photoshop CS5 or 12 elements.

  You could look on Amazon to see if you can get either a product listed above. Just be careful when you buy, make sure you know who you buy from!

  Kind regards

  Pete

• Vista unidentified network problem

  My HP G60 laptop under vista home premium got an "unidentified network" problem and not able to get on the internet. I even tried to reinstall vista to factory default, still the same problem with my wireless router.

  Spec:

  -HP G60 laptop computer, running vista Home premium 32-bit, with 3 GB of RAM

  -Belkin router

  -I am able to connect via a fine wired line but with a Wi - Fi, it shows constantly 'unidentified network', even if I changed the Private mode in network and sharing Center.

  -J' tried the following: listed an SSID different router, reset the router by default, to reinstall vista, tried other mechanisms, such as specified in the forum, with no difference

  -When you configure the router, I have clone MAC of the laptop to the router to get the connection with Comcast, has done that with network cable connected, internet connection worked well after cloning.

  -no virus SW installed.

  Any suggestions on what might be the solution here? Thank you.

  Hello

  It seems that something is blocking the wireless to connect to the wireless router and to obtain a valid IP address.

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Is not start the BITS on Windows Vista Home Premium 32 bit service

  I'm unable to start the BITS service on my computer.
  I use Windows Vista Home preimum 32 bit OS.

  I tried the following solutions that I found here.

  (1) sfc/scannow
  Result:
  =====
  C:\Windows\System32>sfc/scannow

  Start scanning system.  This process will take time.

  Start of the phase of verification of the scanning system.
  Full check of 100%.
  Windows resource protection found corrupt files but was unable to repair some of th
  EM.
  Details are provided in convertible bonds. Journal windir\Logs\CBS\CBS.log. For example
  C:\Windows\Logs\CBS\CBS.log

  C:\Windows\System32 >

  (2) delete the files qmgr0.dat and qmgr1.dat download/ProgramData/Microsoft/network directories.

  I also tried using BITS Repair tool downloaded from the microsoft web site, but no luck.

  When I start the BITS service, I receive the following error message.

  Please suggest me how to solve the problem.

  The service Background Intelligent Transfer Service on Local computer started and then stopped. Some services stop automatically if they are not in use by other services or programs.

  Concerning
  Yannick DEVOS

  I tried to run the Norton removal tool.

  No luck.

  Finally, I reinstalled my OS. When I tried to restore using Windows restore, some applications do not work. Therefore, I have reinstalled my OS.

  Thanks for your great support.

  Concerning
  DeVos

• Windows Vista - naughty network connection

  I seem to have developed a network of rogue connection in Vista.  When I opened the center of network & sharing, I was informed that I have several networks, there are two available on this screen networks - which show the same sky router (which is the only link that I have and it is set for my Windows PC).  However, one is my original and connection existing, listed as 'Home', and it is a private network.  The other is listed as 'Unidentified' and rises as Public.  It will let me delete this connection as it is said that it is currently in use and of course, if I disable the adapter of the sky, or connections are visible and also cannot be deleted.

  I noticed that when I start the PC, it now takes a long time to start - the rest black screens in place for several minutes before the welcome login screen.  Also, I have AVG running and the original sky network has been implemented in the small office or home network and that by default to connect to, however, now, when it starts, AVG reports that it is directly connected "to the Internet" and uses the "unidentified network".  I can't cut it, and if I try to "Connect to a different network", it tells me that there are no available networks.
  I really worry that I may have some virus that takes over my network connections.  I now physically disconnected from the PC to the router for security.
  If anyone can help me with this question, I would be very grateful.  I did a scan of Malware detected nothing, but I don't know that these things are not infalible.
  Any help gratefully received.
  Thank you

  Hello

  Thanks for your reply and my apologies for the delay.  I think I have solved this problem and fortunately, I don't think it was the associated virus.  I had made some changes to the configuration of the network connection (changing to "make a new ip address every time" to 'use static ip address' and I think that might have caused the problem.)  I did a system restore to a time before these changes, and my problem disappeared completely.
  Thanks again for your help.
  Rgds
  Donna

• Can I use my modem wifi re-large up my internet 64-bit of Windows Vista

  ##wifi

  My laptop has a wireless modem, my access to the internet through the LAN. can I use my modem wifi re-large up my internet, so my other computers can us the internet.  I guess what im saying is my card wifi as a hub.   im sorry new to this.

  I use win vista 64-bit
  Thank you

  Hey, I can't install Win7 64 bit...

  Let's get back to a productive tone. You can use the Wi - Fi card on your laptop to create a wireless network for other computers. It is to create an 'ad hoc' network. While going through the installation wizard you can choose to make the ad hoc network, permanent or not.

  Note: You can always remove/delete a permanent ad hoc network at a later date. The permanent setting will allow the ad hoc network to stay open even if no other computers/devices are connected on it.

  To set up the ad hoc network, please follow the steps 1 to 3 as described here:
  Set up a computer-to-computer (ad hoc) network

  Once created the ad hoc network, you need to enable Internet connection sharing for the network. To enable Internet connection sharing, please read carefully the information / the steps here:
  Using ICS (Internet Connection Sharing)

  Note: In the long term, you will experience better performance/stability using a device dedicated to broadcast your network without wire (such as a wireless router). For any future reference the link below will allow you to check to see what hardware is compatible with Windows Vista, so that you can be sure that it will work properly with your computer:
  Windows Vista - wireless routers Compatibility Center

  Hope that helps.

• 7 Windows can I switch from 32-bit of Windows Vista?

  Original title: Windows Vista to Windows 7.

  Dear Sir
  use windows vista with 32-bit now, which Windows 7, can I upgrad
  Thank you

  Hello

  Thank you for contacting Microsoft Community.

  Normally, the option allows Windows Vista Edition family Basique/Familiale Premium to Windows 7 Home Premium, professional or ultimate edition, but all in 32-bit only. You can perform a clean install of Windows 7 64-bit release. You can't pass 32-bit to 64-bit.

  If you feel that your query is not answered, please mention the version you use for you to help.

• Reinstall Windows Defender 32-bit of Windows Vista Home Premium

  I uninstalled Windows Defender computer laptop home premium from Windows Vista 32 bit and this cause the activation of VOLUME to be EMPTY and the speakers may not work. I am able to hear mobile through audio jack.  My question is how do I reinstall WINDOWS DEFENDER, I tried to do, but I get feedback as we can't do to install WINDOWS DEFENDER?

  Hello

  There is no download for Defender to reinstall it in Vista.

  It is part of the Vista operating system.

  You can try this method and do a repair upgrade installation:

  If you don't have a Vista DVD from Microsoft, you can borrow one from a friend and do a repair upgrade installation.

  Recovery disks have normally not these repair options.

  "How to perform a repair for Vista Installation"

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  See you soon.

• Can I upgrade Windows Vista 32-bit to Windows Vista 64 - Bit and preserve everything?

  I have a computer with Windows Vista 32 - Bit OS.  I have also 4 GB of RAM, but as the OS is 32-bit, he acknowledges that 3 out of 4 GB.  So, my question is, can I upgrade to a version 64 bit Vista and preserve files and programs, or what I have to buy a copy of Windows Vista 64-bit?

  Thank you

  Hello.

  No.; You cannot switch from 32-bit to 64-bit.

  It must be done with a new installation of the 64-bit operating system.

  There has never been a way to upgrade.

  You should backup your data, copy it into the 64 bit OS and reinstall all your programs

  Microsoft sells more than Vista.

  And before you buy Windows 7:

  Go to your computer / computer laptop manufacturer Web site and see if Windows 7 drivers are available for your make and model computer / laptop.

  If this is not available, Windows 7 will not properly work for you.

  Run the "Windows 7 Upgrade Advisor.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  Check if your specifications are compatible for Windows 7:

  "Windows 7 system requirements"

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  "Windows 7 Compatibility Center" for software and hardware:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  And the Microsoft Store where you can get an idea of the price of Windows 7:

  http://www.microsoftstore.com/store/msstore/en_US/list/CategoryID.50726100

  See you soon.

• I removed Windows Vista 32-bit and Windows Vista 64-bit installed, but when I enter the key it says the key is already in use. How can I fix it?

  I have Windows Vista Ultimate 32 and 64 bit edition

  I bought Windows Vista Ultimate 32 and 64 in a box in 2008, I installed the 32 edition because at the time I was told not all software will work with the edition 64 a month ago, I decided to windows 7 Ultimate Via Amazon purchase which proved be a copy of the counterfeit money and Amazon me has now repaid , so what I do, well I could buy another copy of windows 7 Ultimate or I could give the other Version of windows that came in the same box with a product key a go, so I removed and formatted the hard drive and reinstalled 64 bit version on my drive using the product key original that I used on the 32-bit Edition for four years and when I try to register the 64 bits edition, that is to say someone else using this product key, you will have to buy another key or a copy of windows 7. Well, I decided to wait until Windows 8 will be released, that's why I decided to try the Vista 64 - bit Edition?

  Or better yet, I might switch to a Mac OS x system?

  The answer is not to buy Windows 7 from a dealer on the market of Amazon.  Stick to Amazon itself.  Amazon Marketplace is as eBay and other auction sites and online delivery.  It is composed of persons whose practices sales are questionable.  You won't get counterfeit product from Amazon itself.

  You have to solve the problem with Vista 64-bit using phone activation.

  Activate by phone.  http://TechNet.Microsoft.com/en-us/library/cc736912 (WS.10) .aspx

  Or click Start and type ' slui.exe 4.

  Do not answer all prompts automatic until it asks you if you want to speak to an agent.

  If you continue to have problems with activation, run the MGADiag (download and save to the desktop - http://go.microsoft.com/fwlink/?linkid=52012 ) tool

  Once downloaded, run the tool. Click on the button continue, after a short time, continue button will change to a copy button. Click the copy button in the tool (ignore the error at this stage) and then paste (with r-click and paste or Ctrl + V) in your message.

• Hello, I have a 32-bit of Windows Vista Home Premium...

  Hello, I have a computer of Windows Vista Edition 32-bit Home Premium. I have constantlly error:

  {Code to update Windows 641}

  1.) Microsoft .NET Framework 3.5 Service Pack 1 and the .NET Framework 3.5 Family Update (KB951847) x 86

  Download size: 9.3 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  The Microsoft .NET Framework 3.5 Service Pack 1 is a full cumulative update that contains many new features gradually based on .NET Framework 2.0, 3.0, 3.5 and includes the cumulative upkeep updates for .NET Framework 2.0 and .NET Framework 3.0 subcomponents. The .NET Framework 3.5 Family Update provides important application compatibility updates. This update is provided to you and under Windows Vista and Windows Server 2008 license terms.

  More information:
  http://go.Microsoft.com/fwlink/?LinkId=133335

  Help and Support:
  http://support.Microsoft.com

  (2.) a security update for Microsoft XML Core Services 4.0 Service Pack 2 (KB954430)

  Download size: 5.4 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  A security issue has been identified in Microsoft XML Core Services (MSXML) that could allow a malicious user to compromise your Windows system and take control. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. Once you have installed this item, it cannot be deleted.

  More information:
  http://go.Microsoft.com/fwlink/?LinkId=128803

  Help and Support:
  http://support.Microsoft.com

  3.) update for Microsoft XML Core Services 4.0 Service Pack 2 (KB973688)

  Download size: 5.4 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Install this update to prevent applications from sending too many requests HTTP, while a well-known Document Type Definition (DTD) is included. After you install this item, you may have to restart your computer. Once you have installed this item, it cannot be deleted.

  More information:
  http://support.Microsoft.com/kb/973688

  Help and Support:
  http://support.Microsoft.com

  &

  Windows install:

  [Windows Installer service could not be accessed. This can happen if the Instaler Windows is not installed correctly. Contact support for assistance personnel.]

  ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  I followed several steps on this site and others; cleaning of the registry, using fixit, trying to download Window install 4.5, using system and turn off my antivirus to download new updates. Nothing works now. I even did a system recovery. I can not download FixIt entirely or any other program for help with this error nor can I fix manually without hitting a wall. Windows Installer is not in the registry or anywhere else.

  Thank you for your time!

  Sincerely,

  Taiyou Okami

  Hello

  1 is specific to installing windows update or install other programs as well the question?

  2. check if the installation of windows services is present in the services.

  To check if the Windows Installer Service is present in the Services, please follow the steps mentioned below.
  
  a. click Start, type services.msc in the search box and press Enter to open Services.
  b. find the Windows Installer service in the service list.

  I suggest you try the steps mentioned below and check if it helps.

  Method 1: You can try to reregister the windows service install.

  To do the same, please follow the steps.

  a. click Start, type cmd in the search box, then right-click on command prompt.
  b. at the command prompt, type of the following command, and then press ENTER after each line.

  MSIExec /Unregister
  MSIExec/regserver

  c. Exit at the command prompt and see if you can download and install windows updates.

  Method 2: If the problem persists I suggest you try the procedure described in the below mentioned link and check if it helps.

  Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2:
  http://support.Microsoft.com/kb/2509997

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.

  How to back up and restore the registry in Windows:
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Warning: We recommend not to interrupt the CHKDSK process. Microsoft does not guarantee the integrity of the disk if the CHKDSK program is interrupted. For security, you can back up your data before using check disk drive.

  Hope this information is useful.

   

• I have to reformat I can use transfer from windows 7 64 bit for windows vista 64-bit

  I have a few problems and have to reformat my desktop computer. I can't save anything, but I have most of my files and folders transferred to my new laptop. My question is, the Office has a VISTA 64 bit OS and the laptop has a 64-bit WINDOWS 7 OS. Can I use easy transfer to trans iron files & back files of the laptop on the desk.

  Thank you

  PETER

  Hi Peter,.

  Windows Easy Transfer generally works from a lower to a higher version of Windows or the same version of windows.

  You can try to download the Windows Vista 64 - bit easy transfer and try to transfer the files and folders and check if it works. If it does not from Windows 7 to Vista, then you must manually copy the files and folders using USB drives.

  For more information, you can consult the following articles.

  Windows Easy Transfer

• Repair BITS for Windows Vista tool download

  When I want to install the BITS Repair tool page validation is in place. I posted 3 times and still not get the download. Any suggestion? Thank you!

  Hello

  Try the procedure described in the following article:

  An update is available to resolve a Service outage of Intelligent Transfer (BITS) background on a Windows Vista-based computer: http://support.microsoft.com/kb/940520