3750 stacked switch question

Hi all

If I need to reboot the switch due to a mistake I did on an ACL to get the boot configuration, can I restart the breaker or the whole stack?

Thanks in advance,

If you have console access you will need to plug into the battery to reboot to get the configuration, once you save it after that you applied the acl, it will revert to the previous config

a cleaner way is to try get console on it and remove the config but, restart the entire stack is going to be service make for a large number of devices

Tags: Cisco Support

Similar Questions

  • iSCSI with stacked switches

    Hi guys,.

    I have a client who is looking to implement a new iscsi solution.

    We are looking for in the design of the network iscsi at the moment and my preference would be to have two switch dedicated for iscsi traffic.

    The customer, however, is eager to use 2 switches configured as a battery and use a vlan.

    So my question is, connecting the iscsi network to stacked switches would cause problems in terms of failover etc.?

    Thank you

    DC

    NO it shouldn't cause any problems-

    If you find this or any other answer useful please consider awarding points marking the answer correct or useful

  • 3850/3750 autonomous or Distribution stacked layer Question

    Hi all

    I have a client with three buildings all very close to the other dorsal 62.5 MM of fibre. They exceeded it current topology and I am trying to implement a distribution layer using a couple of 3750's or 3850's. They have already invested in Netgear at the access layer and I try to make the two work together, Cisco and Netgear. My experience is with Cisco don't know Netgear as well. The mixed vendor environment needs tests, the thing I'm not sure of using a distribution layer stacked with channels of ether of the access layer.

    The attached drawing shows the topology, I thought however, I have some concerns that I have documented in the drawing. Any advice would be appreciated.

    Andy

    Disclaimer

    The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose. Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

    RESPONSIBILITY

    Any author will be responsible for any damage that it (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

    Poster

    Would you consider using a chassis with redundant sup, power supplies and descenders, for the same device, on maps of different lines, as a device of distribution (or core)?  If so, it's about what you have with a battery (or VSS pair).  That is, if a frame (or a VSS pair) is a valid design, why a battery would be too.

    The benefits you have noted on your schema, for a battery would also apply to a frame (or a VSS pair).  Plus, you get more bandwidth.  PLEASE didn't need to block a redundant L2 path and stacking cables can provide more bandwidth then port 'normal '.

    EtherChannel should work between sellers using LACP.  (At least on Cisco, remember to choose an optimal hash algorithm.)

    The main disadvantage of a pile of Cisco, as a single chassis support redundancy, all the material is in a physical location.  Something is happening to this unique physical location, you lose this distribution node.

    Another downside, you are subject to a software problem, as a single logical device (applies also to the simple chassis or pair VSS), but with multiple devices of L2, you are then subject to defects of FHRP, STP, etc..

  • 3750 X stack and question wccp ACNS Content Engine (CE)

    Hello

    I work with 3 3750Xs in a 'carrot' and we have a directly connected content engine (CE) on a WAE-612 CNSE ce612 - filtering 5.5.23.2 running web services. We use the wccp with forwarding L2 and L2 return with assignment of MASK.

    The this is located in the vlan 1013 and is directly connected to the 3750Xs of base via po5.  Users are in vlan 72 a stack of 3750Xs in a closet of access that is connected to the base through PO4.  64 VLANS plugs on the perimeter (to the Internet) firewall.

    When only one member of PO4 is physically connected web filtering works, however the web filtering does not work when several members are connected in PO4 and end-users are not filtered.  It seems the 3750Xs kernel redirect not the traffic to THIS more at this time.

    Anyone have any ideas why adding members to the port channel seems to break the wccp functionality.  Would it be due to the "Battery cross" of the channel port?

    Here are some details of the 3750 basic configuration s

    *************************************************************************************************************************************

    #show CORE-3750Xs version

    ...

    c3750e-universalk9 - mz.122 - 58.SE1.bin

    *************************************************************************************************************************************

    CORE-3750Xs #show license

    1 function of the index: ipservices

    ...

    *************************************************************************************************************************************

    CORE-3750Xs #show run int vlan 1013
    interface Vlan1013
    WAE-Smartfilter description
    IP 10.144.1.193 255.255.255.192
    no ip proxy-arp
    *************************************************************************************************************************************

    CORE-3750Xs #show run int vlan 72
    interface Vlan72
    Description STDNT_wired_a114
    IP 10.144.72.1 255.255.255.0
    IP helper 10.144.6.2
    no ip proxy-arp
    property intellectual cache wccp web redirection in
    IP pim sparse - dense mode
    *************************************************************************************************************************************

    #show run int vlan 64 CORE-3750Xs
    interface Vlan64
    IP 10.144.64.1 255.255.255.0
    IP helper 10.144.6.2
    no ip proxy-arp
    IP pim sparse - dense mode
    *************************************************************************************************************************************

    CORE-3750Xs #show run int po4
    Interface Port-Channel 4
    Description * Port channel of closet 114a *.
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 2,3,9-12,20,40,41,72,100,608,614,1423,1620
    switchport trunk allowed vlan add 3001-3003
    switchport mode trunk
    switchport nonegotiate
    disable the protocols spanning-tree bpdufilter
    disable the protocols spanning-tree bpduguard

    *************************************************************************************************************************************

    CORE-3750Xs #show etherchannel 4 sum
    Flags: - Low P - D bundled in port-channel
    I have - autonomous s - suspended
    H Eve (LACP only)
    R - Layer 3 S - Layer2
    U - running f - cannot allocate an aggregator

    M - don't use, minimum contacts not satisfied
    u - unfit to tied selling
    w waiting to be aggregated
    d default port

    Number of channels in use: 5
    Number of aggregators: 5

    Protocol for the Port-Channel port group
    ------+-------------+-----------+-----------------------------------------------
    4 (SU) Po4 - Gi1/0/20 (P) Gi1/0/21 (P) Gi1/0/22 (P)
    Gi2/0/20 (P) Gi2/0/21 (P) Gi2/0/22 (P)
    Gi3/0/21 (P) Gi3/0/22 (P)

    *************************************************************************************************************************************

    #show run int po5 CORE-3750Xs
    Interface Port-channel5
    Description * Port engine content channel *.
    switchport access vlan 1013
    switchport mode access
    *************************************************************************************************************************************

    CORE-3750Xs #show etherchannel 5 sum
    Flags: - Low P - D bundled in port-channel
    I have - autonomous s - suspended
    H Eve (LACP only)
    R - Layer 3 S - Layer2
    U - running f - cannot allocate an aggregator

    M - don't use, minimum contacts not satisfied
    u - unfit to tied selling
    w waiting to be aggregated
    d default port

    Number of channels in use: 5
    Number of aggregators: 5

    Protocol for the Port-Channel port group
    ------+-------------+-----------+-----------------------------------------------
    Po5 (SU) 5 - Gi1/0/5 (P) Gi2/0/5 (P)

    *************************************************************************************************************************************

    CORE-3750Xs #show ip web cache wccp
    The WCCP customer information:
    WCCP Client ID: 10.144.1.194
    Protocol Version: 2.0
    Status: usable
    Redirect: L2
    Package return: L2
    Directed packets: 0
    Connection time: 10:15:38
    Assignment: MASK

    Mask port DstAddr SrcPort DstPort
    ----  -------    -------    ------- -------
    0000: 0x00000000 0 x 00001741 0x0000 0x0000

    Value port DstAddr SrcPort DstPort CE - IP
    ----- -------    -------    ------- ------- -----
    0000: 0x00000000 0x00000000 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0001: 0x00000000 0x00000001 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0002: 0x00000000 0 x 00000040 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0003: 0 x 00000000 00000041 0 x 0 x 0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0004: 0x00000000 0x00000100 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0005: 0x00000000 0 x 00000101 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0006: 0x00000000 0 x 00000140 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0007: 0x00000000 0 x 00000141 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0008: 0x00000000 0 x 00000200 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0009: 0x00000000 0 x 00000201 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0010: 0x00000000 0 x 00000240 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0011: 0x00000000 0 x 00000241 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0012: 0x00000000 0 x 00000300 0000 0 x 0 x 0000 0x0A9001C2 (10.144.1.194)
    0013: 0x00000000 0 x 00000301 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0014: 0 x 00000000 00000340 x 0 0 x 0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0015: 0x00000000 0 x 00000341 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0016: 0x00000000 0 x 00000400 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0017: 0x00000000 0 x 00000401 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0018: 0x00000000 0 x 00000440 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0019: 0x00000000 0 x 00000441 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0020: 0x00000000 0 x 00000500 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0021: 0x00000000 0 x 00000501 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0022: 0x00000000 0 x 00000540 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0023: 0x00000000 0 x 00000541 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0024: 0x00000000 0 x 00000600 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0025: 0x00000000 0 x 00000601 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0026: 0x00000000 0 x 00000640 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0027: 0x00000000 0 x 00000641 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0028: 0x00000000 0 x 00000700 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0029: 0x00000000 0 x 00000701 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0030: 0x00000000 0 x 00000740 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0031: 0x00000000 0 x 00000741 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0032: 0x00000000 0 x 00001000 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0033: 0x00000000 0 00001001 x 0 x 0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0034: 0x00000000 0 x 00001040 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0035: 0x00000000 0 x 00001041 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0036: 0x00000000 0x00001100 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0037: 0x00000000 0 x 00001101 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0038: 0x00000000 0 x 00001140 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0039: 0x00000000 0 x 00001141 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0040: 0x00000000 0 x 00001200 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0041: 0x00000000 0 x 00001201 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0042: 0x00000000 0 x 00001240 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0043: 0x00000000 0 x 00001241 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0044: 0x00000000 0 x 00001300 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0045: 0x00000000 0 x 00001301 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0046: 0x00000000 0 x 00001340 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0047: 0x00000000 0 x 00001341 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0048: 0x00000000 0 x 00001400 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0049: 0x00000000 0 x 00001401 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0050: 0x00000000 0 x 00001440 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0051: 0x00000000 0 x 00001441 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0052: 0x00000000 0 x 00001500 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0053: 0x00000000 0 x 00001501 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0054: 0x00000000 0 x 00001540 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0055: 0x00000000 0 x 00001541 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0056: 0x00000000 0 x 00001600 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0057: 0x00000000 0 x 00001601 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0058: 0x00000000 0 x 00001640 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0059: 0x00000000 0 x 00001641 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0060: 0x00000000 0 x 00001700 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0061: 0x00000000 0 x 00001701 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0062: 0x00000000 0 x 00001740 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)
    0063: 0x00000000 0 x 00001741 0x0000 0 x 0000 0x0A9001C2 (10.144.1.194)

    *************************************************************************************************************************************

    CORE-3750Xs #show ip wccp web cache
    Global information WCCP:
    Router information:
    Router identifier: 10.144.75.1
    Protocol Version: 2.0

    Identify service: web cache
    Number of Clients of Service Group: 1
    Number of routers in Service Group: 1
    S/w redirected packets total: 0
    Process:                                     0
    CEF:                                          0
    Redirect the access-list: - none -.
    Redirect denied packets total: 0
    Packages not assigned total: 0
    Group access list: - none -.
    Total Messages refused for the Group: 0
    Total authentication failures: 0
    Total GRE bypassed packets received: 0

    Check the license on stack x 3750.  Master suspect IP services, other members have only basic IP.

  • [3750 x] switch was able to start on the new image

    Hello

    I have updated the firmware of my switches 3750 x (19 switches in the Group 8 battery) with the new version. But 2 switches with a stack of 3 cannot take the last version. They are the same model, I do not understand why they cannot start on the new image.

    New version: 15.0 (2) SE7

    Old version: 12.2 (58) SE2

    Switches information

    17 switches that works

    WS-C3750X-24 15.0 (2) SE7 C3750E-UNIVERSALK9-M

    Revision number of the model: A0
    Motherboard revision number: A0
    Model number: WS-C3750X-24 t-S

    Of the 2Switches that does not work

    WS-C3750X-24 12.2 SE2 (58) C3750E-UNIVERSALK9-M

    Revision number of the model: A0
    Motherboard revision number: C0
    Model number: WS-C3750X-24 t-S

    It's the only different, I found between the 2 switches with all other switches,

    Loading images

    In step 1 it load the image, but it will not start and in the end, it loads the old image and boot top.

    Loading ' flash: c3750e-universalk9 - mz.150 - 2.SE7.bin "... @.

    @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

    @@@@@@@@@@...

    File "flash: c3750e-universalk9 - mz.150 - 2.SE7.bin ' unzipped and installed, point of entry: 0 x 3000
    execution of...

    "Loading Flash:/c3750e-universalk9-mz.122-58.SE2.bin"...@@@ ".

    @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

    @@@@@@@@@@...

    The switch that has the latest version can not see the other 2 stacks. At the moment the only solution I found is the downgrade of the switch with version 15.

    Kind regards

    The latest version that starts with success on this device is 15.0 (1) SE3

    The 15.0 (2) * or 15.2. * the images do not start and lead the suspended device during the @ as stated above.

    So, it seems than Cisco already broken that in 2012. I almost can't believe it.

  • TDMS Defrag progress switch Question

    Starting in 2015 from LabVIEW (I think), there is a bundled with LabVIEW example that shows how to defragment a PDM file and get the status of the defragmentation process.  This example uses two screws again, one to enable and disable the indicator telling the defragmentation to provide status and other VI to actually get the progress.

    My current design is through an actor architecture where each test site will be a reentrant VI manages journaling of the criterion on this location.  And I wanted to get this actor of logging check to see if the file is fragmented and defragment it periodically.  I join defragment at the end of the trial.  I thought I had a this defragmentation progress would be a great feature, but with these two screws being undocumented, I don't know how they will work when there are parallel processes potentially also defrags on other files.

    My question is in what regards progress switch turning off.  For progress should be submitted, you must turn on the switch, then you can read the current status and in the example, it shows the turning off of the switch.  But if I'm defragmentation with a progress bar in a parallel process, turn off the switch it disables all files and this isn't what I want.  What impact could I see so if I leave the switch of defragmentation on throughout the life of the application?  A small example of what I'm hearing is attached.  It generates two files, one who takes one longer defrag than the other, but they both start at the same time.  If I turn off the switch when the first stops, then progress will be not indicated for the second file.  I'm okay leaving activated forever?  Or do I need to track which files are to be defragmented and turn off the switch when they are all done?

    Either way, the lack of documentation on these features exist in 2016.

    As you have found that if you turn off the switch of progress, may not be all the defrags for different files. Leaving eanbled forever is good, but can do a little slower for the case of not having to view the progress of the defragmentation.

    Jie

    OR R & D

  • Possible to stack switches 4 7048 2 on each floor

    How would you stack a total of 4 7048 switches with 2 switches on each floor?  Two groups of 2 switches are located 1 floor independently of the other.  What additional modules and cables are needed?

    Thank you.

    Hello

    You would daisy chain between stackable modules on all four switches. Cumulation between the floors is probably not going to work properly, as the distance of cable max is 3 m. http://www.Dell.com/downloads/global/products/PWCNT/en/PowerConnect-7000-stacking-white-paper.PDF page 2

  • RTMP Adaptive switching question

    Hello Mr.


    I create a flash player using osmf plugin and smilplugin code I found (ofhttps://getstreaming.wordpress.com/2011/05/27/dynamic-streaming-test-drive/#comment-349).


    I have a problem when playing SMIL file in my "player customized" through wowza media server.

    The question is adaptive switching does not work in my custom player if RTMP protocol, but my custom player play more smil with Adaptive url switching and manual switching (@! http://mediapm.edgesuite.net/OVP/content/Demo/SMIL/elephants_dream.SMIL ).

    and also play HDS and HSL streaming through wowza media server.

    I appreciate your help.

    sample smil file which I use for below Wowza

    <? XML version = "1.0" encoding = "UTF-8"? >

    < smil >

    < head >

    < base meta = "_definst_/vod / rtmp://127.0.0.1:1935" / >

    < / head >

    < body >

    <>switch

    < src = 'mp4:main360.mp4' video system-bitrate = "200000" / >

    < src = 'mp4:main720.mp4' video system-bitrate = ' 480000 "/ >"

    < src = 'mp4:sample.mp4' video system-bitrate = ' 720000 "/ >"

    < / switch >

    < / body >

    < / smil >

    Hello

    Please use following methods to play RTMP SMIL-

    private var dynResource:DynamicStreamingResource;

    private var tracingNetLoader:TracingNetLoader;

    private var element: VideoElement;

    private void createSMILObj(str:String):void {}

    try {}

    var objSMIL:Object = createSMILObj (str); Function give below

    var obj:Object is objSMIL ["files"];.

    var fileLen:Number = getObjLen (obj); function given below

    dynResource = new DynamicStreamingResource (String (objSMIL ["baseURL"]));

    vector = new Vector. (fileLen);

    for (var i: int = 0; i

    Vector [i] = new DynamicStreamingItem(obj[i].src,obj[i].bitrates,obj[i].width);

    }

    dynResource.streamItems = vector;

    tracingNetLoader = new TracingNetLoader();

    element = new VideoElement (dynResource, tracingNetLoader);

    initPlayer (element);  Pass this object OSMF element and play the video.

    } catch (error: Error) {}

    trace ("detected in the SMIL XML loading error")

    }

    }

    public static void createSMILObj(_str:String):Object {}

    var baseUrl:String;

    var smilXML:XML;

    var videoList:XMLList;

    var mainObj:Object = new Object();

    var fileObj:Object = new Object();

    var str:String;

    var tempArray:Array = _str.split (')");

    var tempStr:String = String (")"+ tempArray [1]);

    Str = String (tempStr) .split (")<><>

    Str = Str.Split (")

    Str = Str.Split ("System-Bitrate"). Join ("systembitrate");

    smilXML = new XML (str);

    baseUrl=smilXML.head.meta.@base;

    trace ("base =" + baseUrl);

    videoList = smilXML.body.switchs.video;

    try {}

    for (var i: int = 0; i

    .@width fileObj[i]={src:videoList[i].@src,bitrates:videoList[i].@systembitrate,width:videoList[i]};

    }

    } catch (error: Error) {}

    trace ("error detected in SMIL XML File Update...")

    }

    mainObj ['baseURL'] = baseUrl;

    mainObj ["files"] is fileObj;.

    Return mainObj;

    }

    public void getObjLength(obj:Object):Number {}

    var number: number = 0;

    for (var id in obj) {}

    counties ++;

    }

    return of the counties;

    }

    Best regards

    Sunil Kumar

  • ESXi NIC Teaming - switch Question

    Got my first server ESXi upward and running last week.  This is my first production ESXi server.  The hardware itself has dual NIC from what I can tell, ESXi 4.1, if you put the NETWORK interface card in 'team' (I don't think that's the term they call it) ESXi will do a bit of himself load balancing, but also be able to use only one or the other in case of failure in the course.  So, my question is this, if I have 2 NIC on my server set in 'team', that I need to adjust the 2 ports on the switch to shared resources, as I do for any other server?  Or ESXi he manages in a way that I wouldn't need to put in place the trunking of the switch ports?

    That's right – from san traffice some through any port with all the load balancing methods you'll need to configure the same trunk ports

  • Bug to stop random, DIFFERENT from the power switch question

    I found a problem that I have yet to isolate the cause of the, but his is happened a few times now.  Sometimes, when my Sansa has updated its database and has not played a song at the moment, if I change the settings and then try to play a song, it starts to play, then cut completely.  It doesn't happen often, but these are the circumstances each time.  The player will not respond and will refuse to power on.  The only way to get on is to hold the power switch until the device resets, release, and then power it turned on, which of course means another data refresh.  Once this is done, my settings are all back to where they were before the last change, I can change their return, and everything works fine.  As I said, the problem don't occur often, only about 3 times since I've had (since June), but its still an obvious problem.  If someone wants to know more about it, or want me to try a few things, let me know.  I'm mainly just let Sandisk people know, then maybe we can get this in a future firmware update.

    New firmware is in the release process now, so hang on until release us the next version.  It can help about this.  Should be within 1-2 weeks.

  • BlackBerry software Z10 Q10 device switch question

    Attempt to use Blackberry link to a switch of the device to a Z10 with Q10.

    See the error message:

    http://i.imgur.com/PBScXOe.PNG

    Legend of the error:

    No data is transferred

    No data is transferred for the following reasons:

    -The version of the OS on your new device is older than the version of the OS on the device, that you spend. Select a different device or cancel the transfer

    Versions of the software:

    Q10 - not locked to Bell Mobility - 10.1.0.238 - no software update available

    Z10 - not locked to Bell Mobility - 10.1.0.273 - no software update available

    Don't link Version - 1.1.0.37 - no software update available

    Unfortunately, this is a limitation of the BONES of BB10. You cannot restore a backup of a newer version of OS to an earlier version. You can restore a backup from an earlier version to a version identical or newer only.

    You need the Q10 to be on a more recent version. Your only option is to install a "leaked OS ' on the Q10 in order to be able to restore your backup data or transfer.

    Here is a link to the latest OS for the Q10. Everything you do is download the file, it will be a .rar file, so you will need a tool for decompression like 7zip to unzip the .exe file. Then connect the Q10 and run the .exe file and it will update the operating system. Need you more time to download the different file in order to install it, too. It takes about 5 minutes to load the new operating system.

    http://CrackBerry.com/leaked-OS-10102342-BlackBerry-Q10

  • Several VLANS and DHCP relay on two stacked switch SGE2000-G5

    We were put to the task of securing a small desktop system managed that is currently set up with a standard switch for each of the offices (with different companies) to see each other and in some cases, access to each of the other documents on the network.

    Obviously, this is far from adequate set up and our goal is to isolate each office using VIRTUAL networks, but share a common internet connection provided by managed offices.  We have two switches for layer 3 Cisco SGE2000-G5, but we are new on Cisco equipment and VLAN, so we are not quite sure on how to implement this.  DHCP must be provided by a router, there is no server.  We are open to suggestions on the router as we still buy a.

    I hope that someone may be useful.

    Thank you very much

    Jim

    Hi Jim,.

    SGE2000 switches you are using must be able to handle this without issue. What type of router you are using? As long as you have a router that will take in charge VLAN / several subnets, it should be a simple configuration.

    Here's a quick run down of the measures to be implemented. (using vlan1 and vlan2)

    On the router, create a vlan / subnet 2 and set the port to connect to your shared resources with the two VLAN 1 and 2 switch. (it will be untagged, two will be marked)

    On the switch, create vlan2 and do the same for the port connected to the router. (vlan1 marked and tagged vlan2)

    Now for each switch port that you want to assign the port access and vlan1 and vlan2. (this vlan will be without a label)

    If your router allows, disable routing inter - vlan. If this isn't the case, you must create rules to block traffic from one network to the other.

    All this happens under the assumption that your router can support VLAN and can also make DHCP for this VLAN.

    Hope this information helps

  • RedHat Jdev 11.1.2.3 5.8 - AF:Switcher Question

    Hello:

    AF:switcher component can be used in a page Fragment?

    Also, I use the method of creation of functional subsystems like adflibs and then combine these subsystems into a master project to generate ear.

    Subsystems would use page fragments because the master project use the page template and use fragments of page subsystem in the page template? What is the best way to organize: models, fragments and dynamic regions in the context of functional subsystems (adflibs) consumed in a main workspace of the page? Any adivce on this?

    Thank you much for the help.

    What makes you think that he (af:switcher) cannot be used in a fragment?

    Watch this video http://download.oracle.com/otn_hosted_doc/jdeveloper/11gdemos/AngelsInTheArchitecture/AngelsInTheArchitecture.html for an overview of the architecture in the ADF application. You use case is about possible architectures.

    Timo

  • Need help with orders to clear a N2024 stacked switch port configuration

    The current config is:

    interface item in gi1/0/20

    Speed 1000

    Description "WifiLocation2".

    VLAN allowed switchport General add 154

    switchport general allowed vlan add 153 tag

    switchport vlan allowed General remove 1

    switchport access vlan 15

    LLDP transmit tlv ESCR-sys sys - cap

    LLDP transmit-mgmt

    notification of LLDP

    LLDP-med confignotification

    disable voice vlan auth

    I need to look like:

    interface item in gi1/0/20

    Description "WifiLocation2".

    switchport access vlan 15

    I tried a lot of things, but cannot get rid of the lines switchport

    any help would be appreciated

    Clayton

    Another way to remove the general lines switchport is to use the option "Delete" on all VLANs currently associated.  Just like what has been done for the vlan 1 in your example. Something like this:

    switchport vlan allowed General remove 153, 154

    Make sure you have the mode set correctly.  By default, the access mode is set.  If the default value of access is being used, the lines "switchport general" are ignored anyway.

    Hope this has been helpful.

    B

  • Reference Dell place 8 7840 switch question

    first of all, I bought this tablet January in 2015.

    I found this unit turns off by itself at 22% battery while it helps (about a month) and now it shuts down to 37% and more.

    in order to turn on, I need to plug.  If not, there is no way to run.

    In addition, one of my knowledge that the same problem has happened since subsequently used this tablet about six months ago. (so he did factory reset, but its still the same today.)  I guess that this tablet has technical difficulties.

    I am living in Korea and asked for a chat on the official website of dell service, but they just gave me a number of international appeal.  You would not solve this problem.

    Hello

    Please write to us!

    This could be a battery problem. Check the following

    1-battery health in BIOS

    2 - update the BIOS

    3. allow the inactive tablet to check if the battery runs out.

    Nicely private message the service tag and your email address.

    Thank you

    Robin

Maybe you are looking for