598 mhz problem (598 mhz must 1.5 ghz)

Dear members
I received my toshiba m30 laptop to the service tech and noticed that it only works on speed 598 mhz instead of 1.5 ghz!

I did some research and find that it is a kind of problem of mobile microcode (firmware) intel. the CPU info table has to update or something. I'm still waiting for a solution.

Note: I will not send my laptop once again for any technical service cause it will arraive within 30 days.

Hello

I have bad news for you. It seems that you have new main Board and this Service Toshiba partner forgot to update the CPU microcode.

Call them again and they have to do.

Read this. http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=1513

Good bye

Tags: Toshiba

Similar Questions

  • Windows Vista taskbar becomes unusable. If clicking on something other than 'error' beep start. Reseting solves the problem, but there must be a permanent fix. Solvable?

    Windows Vista taskbar becomes unusable. If clicking on something other than 'error' beep start. Reseting solves the problem, but there must be a permanent fix. Solvable?

    Hi Comintern,

    ·         Did you do changes on the computer before the show?

    ·         You receive an error message or error code?

    Follow the suggestions below for a possible solution:

     

    Method 1:

     

    Step 1: Start in safe mode and check if the problem persists.

    Start your computer in safe mode

    http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

     

    Step 2: If the problem does not occur in safe mode, you can put your system to boot (in normal mode) to solve the problem.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

     

    Note: After troubleshooting, be sure to configure the computer to start as usual as mentioned in step 7 in the above article.

    Method 2: I also suggest that you scan your computer with the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

    The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

     

    Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

    Important: While running scan on the hard drive if bad sectors are found on the hard drive when scanning try to repair this area if all available on which data may be lost.

    Let us know the results.

  • Satellite M30X-124 stucks to 591 MHz (Centrino 1.6 Ghz)

    Hello world!

    I have a 'M30X 124"which normally takes place on 1, 6 GHz, when I use it with my diet.
    No matter what I change on the speed of the processor in this Toshiba tool, it still works on 591 MHz!

    I have not used for 2 years. Now, I've seen this problem.
    My motherboard has been changed until I stopped using it. I read on some forums that it is a problem of communication of processor/motherboard... and it has a firmware update (or other) on CD that solves the problem. I tried this fix firmware from another laptop, but without success.

    Anyone know this problem?
    Where can I find this fix - CH?

    Thanks in advanche!
    Steven
    ______
    Toshiba Satellite M30X 124
    Celeron 1, 6 GHz
    Windows XP SP3

    Hello

    I doubt that you can solve this problem.
    The firmware must be updated by Toshiba service technicians

    This is necessary after the exchange of motherboard or the CPU will be blocked to 600 Mhz.

    Get in touch with ASP in your country and ask for help!

  • Can I choose 40 MHz to 5.2 GHz and 20 MHz to 2.4 GHz channels at the same time?

    I have a WLC 5508 and 3500 6 LAP at the head office, 2 to another office and 2 to another office.

    I noticed that even when I specify 5.2 GHz on my (Intel Centrino Advanced-N 6230) wireless adapter it indicates the data rate is 144 Mbit/s.  I want to try to get 300 Mbps out of it and I think I need to enable 40 MHz wide channels in the range 5.2 GHz.  Well, I don't want to cause any disturbance to the network currently associated clients.  What can I do?  What happens if a client adapter does not support the wide 40 MHz channels?  Then I keep 2.4 GHz at 20 MHz wide channels, and then they would just connect to the frequency range of 2.4 GHz?

    Where would I go to change the width of the channel of 5.2 GHz only?  It is defined globally or I put it for each access point?  I saw a button radio for 20 MHz or 40 MHz to this place: Wireless > 802. 11A / n > RRM > DCA

    That's where I'd do the settings to change?  If I would work the clients on the network briefly?  Do 802.11n 40 MHz channels are supported by all adapters with 5.2 GHz radios?

    Looking at the use of the string with a program called inSSIDer 3, there is nothing past in the band 5 GHz except for us.

    Thanks for the help.  Just trying to get the best possible flow that I've had a few requests SMB based respond slowly or poorly when on... wireless connections even when the operating system reports 144 Mbps.

    Here is a shot... screen mine will be different because I use a beta code:

    Thank you

    Scott

    Help others by using the rating system and marking answers questions as 'response '.

  • My pc is unable to load the program except in safe mode, which is a recent problem. Time must also be reset whenever I start. any suggestions

    At startup the program do not load beyond the xp logo and then a black screen. The only way to load is in safe mode. The clock needs daily update, is it connected?  I can't restore, but might do at the beginning, but not more. My antivirus is also disabled, it's because its in safe mode. Could all this be reduced to a battery of spleen?

    people suggestions.

    Hi Mike,.

    ·         You did changes to the computer before the show?

    Try the following.

    Method 1: Read the following article.

    After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

    Method 2: Follow the steps in the article mentioned below.

    After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  • Problems that I must correct.

    QUESTION?  I'm 82 years old, so I'm slow on typing, having attended the school in 1946... I think I started with LR 3 and forward, which carried into Lr 4.

    In any case, I always upload my pictures on PC 'Image '. I have about 12, 000images. I was skeptical as the implementation of the catalog and I think that I "added" only one entrance to the

    Catalog. When I tried to checing results, I found nothing.   Thus, virtually all of my photos remained in the left panel. ...... 4.3 LR has been downloaded recently. I checked LR 3 and found

    my catalog 'Gift-3' and he chose as the cat for LR4.3. then I went to the Panel on the left and found my 'photos go here' and click on the left 'Import '. I think I realized that

    several times, but the 'import' that was available on the right panel, I was wrong. Sooooh, I guess the easiest station is to delete all imports in the left

    Panel and initially above. Since I expect not to have all the entries in the catalog it would be better to name "Don.cl4"? I expect to see anything in this catalog, since I know that

    any changes to the photos is actually saved in C: drive in the pictures folder.  I don't know what to expect to find in the .lrcat! I appreciate all the help you provide. I followed many tutorials on the web, including those of Mark? Kost, Terry White and Laura Shoe. However there is no help from how to make corrections, except, I guess, to erase any thing in LR and start over. Oh! Either incidentally, the photos I saw were originally large such as they appear in the content space. But as the final image of the entered file, they are all becomes grey, as being covered with a veil. That shows that? I bought four texts which have not provided answers to my questions. Thank you once again. I'll get your answeers

    tonigjt later since I need to make a run now.
    Thank you!!!   Donald Kuxhausen, [email protected].          Tel: 208-888-5718.

    First: Thanks for the reply. I'm sorry that I don't remember details. I probably didn't creat my Lr3 correctly. I added only the first folder. When I tried to check, I didn't find any registration. So I simply imported files in the Panel left, use 'Add' but never used the right panel.

    During the inspection of the left panel in the Lr4, I now findthe unorganized records (seven appears after Oct).

    Refer to your conclusion, Yes, I wanted to move to 4 Lr. However, I believe that I have nevercorrectly 'added' images FOR the lr catalog 3, in the first place. I didn't know how to check the caatalog.

    Can I 'remove' all the folders in the left panel of the Lr4 and start over?

    I really appreciate your advice and time!  Thank you.   Don Kuxhausen

  • T500 P8600 (2.40 Ghz) Core speed problems - works only in 1, 6 GHz (6 x multiplier)?

    Hello

    I'm new here and I hope you can help!

    System specs

    Lenovo T500 (2081-CTO)

    CPU: Intel Mobile Core 2 Duo P8600 2.40 GHz

    RAM: 6 GB DDR3 PC3-8500 (2 GB + 4 GB Hynix halogen)

    BIOS Lenovo: 3.13 - 1.06 (March 2010)

    Operating systems: Windows 7, 64 bit

    Battery: Yes

    Power: 90W installed

    Power setting: maximum performance; Max CPU speed: more top [ThinkVantage Power Manager 3.12]

    Setting BIOS: Intel SpeedStep disabled; Everest EU 5.50 confirms: C1E & EIST are both: "supported, disabled.

    All Lenovo drivers are up to date *.

    ---

    Problem: Base speed is blocked at 1.6Ghz (multiplier x 6.0) and only fluctuates several Mhz from time to time. I think it should be fixed at 2.40 Ghz, I have disabled all the settings save CPU speed.

    Basic speed (1.60 Ghz) conforms to:

    -Everest Ultimate Edition 5.50

    -CPU - Z 64 bit 1.54

    -Intel Processor Identification Utility 4.22.20100224

    All of these are the @2 P9800. 40 Ghz is clocked at 1.6 Ghz or 1.59 Ghz.

    I ran the load/stress test, Super-Pi etc... and obsevered the basic speed - it never changes or is greater than 1.6 Ghz.

    Super Pi takes 31 seconds, where landmarks on a normal P8600 2.40 Ghz see the this should be done in 20 years.

    I have read several threads in these forums and tried all the things suggested:

    Example of Lenovo Forum Thread 1

    Example of Lenovo Forum Thread 2

    I even tried affecting performance Max CPU speed to "Adaptive", and yet, it does not go beyond 1.6 Ghz.

    Can anyone suggest other things I can do to make sure that it is not a problem? I thought I bought a 2.40 GHz, not a 1.6 Ghz.

    I have several more months remaining warranty, contact Lenovo to return my CPU? or is it a fault in Lenovo BIOS?

    Intel speed step must be enabled.  If you read what it says in the bios, if it is off then they processor will not let the State of the minimum speed.  This is the case on my T510.

    Give it a try.

  • Problems of classic blackBerry on 5 GHz network Wifi

    Hello

    just found following problem using this combination:

    WiFi router: apple Airport extreme

    Passport of BB or configured classic dual-band wifi to connect to the router.

    Result: 1-2 MB max (theory, it should achieve easy > 100 MB to download)

    More 2, 4 GHz band, assigning the results are normal

    The two confirm on my classic and the Passport.  It looks like so many combination of Airport extreme and BB 10 device

    Can someone else test this with a device aiport or another router?

    Just restarted airport and have interesting results: now to get the normal result showing 100 MB down.
    Its now using 100 channels, previously channel 36.

    Sorry guys seems not peripheral airport or channel selection/use more related associates.

  • Windows 7 problem on pentium 4 3.20 ghZ, RAM: 2 GB graphics and 1 GB.

    I installed windows 7 Ultimate 32 bit on my Pentium 4 PC, 2 GB of RAM and 1 GB graphics card. but when I connect to the internet and start the browser [Firefox and chrome] PC becomes very slow and tabs open in the browser very slowly... My PC meets system requirements. and when I start opening browsers chess titans or while working, it does not work smoothly [enabling aero makes the same problem] what can I do?

    Configuration of PC under XP:

    The best thing you can do is update your RAM to 4 GB.  I think it's the max for your motherboard.   32-bit Windows will use out of total of 3.25 to 3.5, but there should always be a major help.  2 GB is a minimum for acceptable performance, especially with an older CPU.

  • Portege M100 - blocked processor at 600 Mhz, have tried all BIOS versions

    Just my BIOS was about 1.20 when I went to site Web from Toshiba to get the drivers to install and to found the update the BIOS so I followed instructions burn it to a disk, the last one I have and I went, but after the update, I noticed that xp says he was clocked at 600 MHz not 1 2 GHz.

    So I used the cpuid to see if it is xp, but it shows as running 598,6 MHz processor and can flow to 600,4 MHz max so I went in the BIOS tried off sleep CPU max CPU and so restarted then I thought it was the xp so I reinstalled but still the same I used Suse Linux always the same.

    I've reflashed the BIOS with 1.50 through the same restarted windows. I get on where and it becomes ridiculous, even, I went and found all BIOS versions on the US site of Toshiba, which dates back to version 1.10 to 1.50, so I tried all the. Nothing!

    I am really puzzled that anyone can sort this is really boring and slow.
    Thank you in advance

    Hello

    Just a question; the motherboard has been replaced by the past?

    I know, after the replacement of the motherboard, the test & diagnosis must be performed in order to update the CPU microcode on the circuit board.
    If the firmware is not updated your CPU would be stuck at 600 Mhz.

    In order to update the firmware, the ASP must be contacted.

    The other reason why the CPU runs only at 600 Mhz is the setting low processing CPU Toshiba power saver.
    Check if the Toshiba power saver is installed on your laptop and set the options at a higher level.

    Check it out

  • T540p I7-4710MQ clocked at 800 Mhz

    Hi all

    During the installation of my new t540p I noticed that my cpu is not limited and continue to run at 800 Mhz slow when running on the battery. When I connect the power supply everything seems to work fine, cpu speed limit of 800 Mhz to 3.5 Ghz as it should.

    I have BIOS-> power I changed the modes of 2 batteries for perf max instead of the battery optimized/balanced, but that does not change.

    I created the new power management in windows (win pro 8.1 incidentally) and set the cpu for running on battery min 0% and 100% maximum with the AC settings, but alas...

    any ideas what I can try next?

    Is it a windows problem or something wrong in the bios that Lenovo has set?

    Thank you very much

    Stefan

    After a few more stable and try it seems that the problem is caused by the latest drivers from nvidia optimus.

    After installation of the drivers available on the downloads page the nvidia control panel warned me of new drivers lenovo.

    With the latest drivers installed it throttels the cpu at 800 Mhz when you start an application that in some way, uses the discrete gpu. Even from cpu - z goes down the frequency of the processor.

    Uninstalling the drivers and installing the drivers of lenovo has fixed the problem

  • 20 Mhz vs 40 Mhz compatibility with

    Hello.

    I wonder if there is a difference in connectivity at 20 Mhz and 40 Mhz channels in 5 GHz...

    Assumptions:

    1. I have configured Cisco Client band elect on my WLC

    2. I activated the band Client elect on my wlan

    3. my wifi dual card has a favorite band selected to 5 GHz

    4. my 3700 dual band Access Point configured channel 6 to 2,4 Ghz and channel 36 to 5 GHz.

    5. I connect to channel 36 with my ipad.

    7. from the perspective of WLC I stay connected to channel 36, but I know that channel 40 is a long string of 36, and now I am connected to a channel of 40 Mhz successfully.

    8. I have all of my 600 AP campus with a 5 GHz (40 Mhz for all channels) channel binding. The goal is to increase performance and optimize the use of the spectrum.

    Problem:

    This week I had a company to conduct a study on the spot in my campus building, and they told me to turn off link in 5 GHz channel because if some dual band devices will not be able to connect to the 40 Mhz channel, they will automatically move to 2.4 Ghz.

    There are devices dual band that cannot accept the 40 Mhz channels?

    B - if don't support it not that they will be 2.4 Ghz mode directly or they will stay on the servile channel, but using only 20 Mhz?

    C - he also said that at 40 Mhz have reduced coverage compared to 20 Mhz channel. is that correct?

    I decided to ask the Pro because I'm really suspicious to this topic.

    A - There are dual band devices which cannot support 40Mhz Channels?
    Yes, there is a dual band client that does not support the channel of liaison in 5 GHz. Mostly pre-802.11n dual-band customers.
    B - If the don't support they will mode directly to 2.4Ghz or they will stay on the bonded channel but using just 20Mhz?
    They connect at 5 GHz with a bandwidth of 20 MHz. In any case note that device client is the one deciding what AP they connect and which group. Thus, there may be different behaviors in different clients.
    C - He also told me that bonding to 40Mhz will have reduced coverage compared to 20Mhz Channel. is this correct?
    Now a days WiFi, to reduce access point coverage to meet capacity needs. Challenge with 40 MHz is re - use and co-channel interference. With a width of 20 MHz, you have 13 CH (except UNII-2 Ex) & will be reduced to 6 If you use 40 MHz. So, if you and dense area where more than 6 APs on close by the deployment of 40 MHz could then lead to co-channel interference (CCI), which reduces performance. Deployment of high density therefore prefer to use 20 MHz to 5 GHz channel width or 40 MHz can be used without any other problems. So I would check if they showed to your ITC in your deployment of 5 GHz, then only I would consider to go with 20 MHz on these specific sector and leave the remaining 40 MHz. HTH Rasika * Pls note all useful responses *.
  • Can I put a 133 mhz FSB CPU of P3 on Satellite Pro 4600?

    Hello world
    I have a good old Satellite 750 Mhz pro4600
    and I was wondering if I can install a P3 1 GHz 133 Mhz FSB CPU
    I wonder if this laptop is strictly 100 mhz FSB?
    I hope that I can extend the life of the laptop loyal.

    The 4600 series computer is equipped with a Mobile Intel Celeron processor or a
    Mobile Intel Pentium III processor.

    Mobile Intel Celeron processor
    This processor runs at 650 MHz or 700 MHz.
    The max speed of the FSB Processor: 100 MHz.

    Mobile processor Intel Pentium III, featuring Intel SpeedStep technology
    This processor is working at 650MHz(1.6volts)/500MHz(1.35volts),
    MHz(1.6volts) 700 / 550 MHz(1.35volts), 750 MHz(1.6volts).
    600 MHz(1.35volts) or 800 MHz(1.6volts) / 650 MHz(1.35volts) and supports FSB speed: 100 MHz

    P3 1 GHz 133 Mhz FSB CPU is therefore not possible ;(

  • installation of iTunes on Windows 10 problems

    Trying to activate my new 6 iPhone more and get the error on iTunes.

    iTunes is installed on a machine with the following configuration:

    Written System Information report to the: 10/12/15 14:54:30
    Name of the system: not available
    [System summary]

    Value of the element
    Name of the OS Microsoft Windows 10 Pro
    Version 10.0.10586 Build 10586
    Another Description of the OS is not available
    Manufacturer of operating system Microsoft Corporation
    Name of the system unavailable
    System manufacturer Dell Inc.
    System model Latitude E6520
    System Type x 64-based PC
    SKU system
    Processor Intel Core i7-2720QM @ 2.20 GHz, 2201 Mhz, 4 Lossnay 8 logical processors
    A19 BIOS Version/Date Dell Inc., 14/11/2013
    SMBIOS Version 2.6
    Embedded Controller Version 255.255
    BIOS Legacy Mode
    Baseboard manufacturer Dell Inc.
    Model baseboard is not available
    Name of plinth base
    Role Mobile platform
    State of secure boot not supported
    PCR7 Configuration binding is not Possible
    Windows C:\WINDOWS directory
    System directory C:\WINDOWS\system32
    Boot Device \Device\HarddiskVolume1
    The local United States
    Hardware Abstraction Layer Version = "10.0.10586.0".
    RAK-PC\RAK username
    Time zone Eastern Standard Time
    Physical memory (RAM) installed 8.00 GB
    7.88 GB total physical memory
    5.17 GB available physical memory
    9,76 GB total virtual memory
    7.05 GB available virtual memory
    Pagefile 1.88 GB of space
    Paging file C:\pagefile.sys
    Hyper-V - VM monitor Mode Extensions Yes
    Hyper-V - second level address translation Extensions Yes
    Hyper-V - virtualization enabled in Firmware Yes
    Hyper-V - data execution Protection Yes

    Then, I tried the upgrade of the iTunes application and got the following error:

    I ran the latest Windows updates and still the same above errors continue to occur. Any help will be greatly appreciated.

    Try to repair the Apple Software Update of the programs and features Control Panel, and then reinstall iTunes.

    For general advice, see troubleshooting problems with iTunes for Windows updates.

    The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

    Make sure after you have uninstalled all the components Apple to remove iTunes shortcuts from the desktop, taskbar, or start menu before you reinstall.

    Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

    More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

    Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

    If the problem persists and you have a 64-bit system try for the old version of video cards which is a 64-bit Installer for most of the 32-bit code, similar to all 64 bit iTunes up to 12,1 versions.

    TT2

  • Alienware M17X-R4 video 680M card problem

    Hello guys,.

    I send my PC official service this summer for a completely different matter (keyboard problem) and after she returned from the service that I started having this frustrating problem with my pc that I can't solve approximately 3-4 months. While gaming, I get this gel suddenly after a nod to the screen. After the screen black Windows prompts an error message that says as "video card is not responding and has successfully recovered." And the effects are not always the same. Black screen sometimes does not disappear until I closed and reopened my lit. Black screen sometimes becomes light blue orange same screen and disappears at all. Sometimes it causes a lot of programs exe (Te games, chrome, battle.net) crash and sometimes does not. Also, a note, sound keep coming while these things occur. So if I'm in a Skype call with someone I can keep talking. Finally, sometimes PC completely freezes stutters same sound until I have hard reset from the pc.

    These accidents have recently started to happen very often. Especially when I play WoW.

    I tried the things:

    -Clean inside my laptop and the fans.

    -Back to the old version of the Nvidia drivers & and do a clean install.

    -Back to Windows 7 Windows 10.

    So, I'm quite sure that this is not a software problem. It must be a hardware failure.

    I noticed things:

    -When it flashes get GPU usage is 0%.

    -J' never have this issue while I am only on battery power. But I like unplayable 20-30 fps which is normal on the battery.

    Also another funny, is after my pc is back to the service, it cannot detect my graphics integrated Intel HD Graphics 4000. He is told - not detected-on the BIOS and I can't install the driver because install gives an error message like "this pc can not meet the requirements.".

    Another thing I tried was permutation and tried to RAM individually at different locations. No luck.

    Today, I found a forum thread that says it can be solved by reducing the GPU voltage / shader clock because motherboard sometimes cannot feed the video card with enough voltage. But I can't underclock the same change in my video card shader and voltage clock of any overclocking tool. It is all greyed out and cannot be changed. I can only change clock GPU and memory clock. This tension thing makes sense to me because as I said I have never this questions while I'm only on battery power. I learned that this laptop automatically decreases the voltage GPU when it's on battery only. Is there a way to change the maximum voltage of my video card or not?

    Sorry if I wrote wrong I just tried to be as brief as I can be all by giving as much information as I can.

    I'm in a position of very desperate and out of options. If you have any idea or information, I'm waiting. Thank you.

    Brief rig:
    CPU i7-3820QM

    680M NVIDIA graphics controller

    32 GB OF RAM

    Official version of Alienware Windows 7 & drivers.

    So, I solved this problem on a few days ago. Never had blocked it again. I still don't know the cause, but it turns out that for some reason my GPU has cause of instability when running at full speed, so when I lowered the Base of only 25 MHz clock offset my blocks instantly stopped. I use NvidiaInspector, but I believe you can also use other tools to overclocking.

Maybe you are looking for

  • When I have several tabs open, I only see the tab that I am in, all the other tabs are not visible at all.

    I only know that there is more than one tab open because when I click in the empty space on the tab bar appears the other tab. then the one that I've been on disappears, until I click in the space were is was before. ?? .... Help, please! Thank you v

  • My 160GB Classic iPod won't sync to iTunes

    I use a Windows PC. I just got it connected after questions there.What's music on an external hard drive?The iPod has been reformatted and restored so currently has nothing about it. When I plug it into the computer iTunes said "(étape 1 de 1 détermi

  • Logitech TV Cam HD

    I just bought a Logitech TV Cam HD and can not have to complete the installation of the network due to the failure to connect to the Skype server. It connects to the router, gets an IP, I put in the DMZ and see where it grows the packets to the inter

  • No sound when you export the missing project like HD (AAC codec) video

    Hi there everyone! I am facing a problem when you try to export a finished project to iMovie as a HD video, no sound! Here's the scenario: MacBook Pro (mid 2010), OS X El Capitan free 10.11.2, around 90 GB of space on the hard disk, iMovie ' 09 (Vers

  • When lance azure windows?

    When blue windows run on the operating system market