6 curves 3 plots stacked tracing?

Similar Questions

• report of Crest brand channel

  HY,

  I would ask, how you can score a point on a curve on the report.

  I analyze a few curves and take a peak of the curve and I want to mark the Summit to be seen on the report.

  Somethink like a point and a few lines to the axes X and Y, to see the coordinates of too.

  I use a script to load the data and the report, so I need a VBS command.

  Thank you.

  HI Maria,

  The simplest solution would be to create a "PeakX" and a "PeakY" channel and add a new configuration of curve to plot the curve XY no lines and only markers.  If there is only 1 value in each of these channels, then you will get a marker exactly at this Summit.  If you used the DIAdem peak find the function to determine your peak, then you probably already have channels of pic X and Y.

  Ask if you have any additional questions,

  Brad Turpin

  Tiara Product Support Egngineer
  National Instruments

• Determine the sub-plot clicked in a stacked chart

  I would like to use the mouse upward (Modsdouble click) to detect what plot of a stacked graph of waveform area was clicked.  It doesn't seem to be a property that actually said 'Clicked in field zone n '.  A few properties that identify the coordinates compared to a reference which I can't find in the help of labView (of the locations stacked).

  Is there a property or a common method of calculation of the selected plot area?

  Thank you

  XL600

  AYanez wrote:

  If I have understood correctly, this could help you.

  It's more complicated than that. The limits of the land gives the value of the active parcel boundaries. Locations stacked, the default value is drawn 0. If this gives you the limits for the first plot area. You need get the number of plots and activate to get the values limits for each plot area. When the mouse is clicked you find if it coordinates are included in one of the plot area.

  Here how to do it. I leave to the OP to change mouse double click event.

  Ben64

  

• Drag poles zeros of a bode plot curve

  Hi all, I have a program of field bode, who can draw magnityde vs frequency and phase frequency vs like this.

  

  This bode plot is based on the functions of the poles and zeros. Here is an example showing how to calculate Labview zeros/poles. All values of R and C can be entered by the user.

  

  Now, I am trying to add a function like this:

  (1) the user can use the mouse to drag these two points according to their orientation specific as what this picture shows. When these two points are moved, the shape of this curve will automatically adjust.

  (2) when the user finishes placing them, Labview can detect their location, and then use the equation to understand what value curent R and C.

  Can someone advise how to implement this function? Thank you very much!

  Hello

  What you're trying to sounded so cool, I thought I'd have a quick go.

  I downloaded a very simplified example, which involves programmatically set values in an equation, by dragging a slider on a XY Chart.

  If all goes well, this should give you an idea how to do what you want.

  Here is the link.

  https://decibel.NI.com/content/docs/doc-29647

  Good luck

• A curve with 2 plots 3D graph

  I'm using Labview 8.5 and I have a 3D line chart to which I attribute (x, y, x) = (Latitude, Longitude, Altitude). I would like to add another plot to the graph, but I can't.

  I read in another post that you have to click with the right button on the graph, and then choose the locations tab, but the only tabs that I get when I right click are appearance and Documentation.

  Can someone help me add another curve?

  Thank you.

  epik78 wrote:

  I'm using Labview 8.5 and I have a 3D line chart to which I attribute (x, y, x) = (Latitude, Longitude, Altitude). I would like to add another plot to the graph, but I can't.

  I read in another post that you have to click with the right button on the graph, and then choose the locations tab, but the only tabs that I get when I right click are appearance and Documentation.

  Can someone help me add another curve?

  Thank you.

  In this thread I illustrates how to add a graphic 3d locations.

  Ben

• How to make a scatter plot curve smooth?

  I do a diagram of dispersion plot, with the values supplied for the diagram.

  I plugged all the points on the line, but I get these 'sharp' corners whenever the curve changes direction.

  How can I make cela a smooth curve?

  

  Thank you

  Convert anchor points using the pen path tools.

  Mylenium

• 2 non-equidistant curves of XY to plot against the other

  Hello, I have a few points of recorded data from various sensors XY. Values of X are always the time stamp and the values are the values of the different sensor. Almost all XY curves start and finish at the same time (most less than a few seconds). In addition, the curves are not equidistant, I mean that the data points are not at the same time stamps. In addition, some of them have been registered with 60 sec, others with sampling frequency of 1 sec (etc...). In fact, this is why I use a graph XY to present these curves together.

  I would like to examine certain correlations, so I want to trace two arbitrary XY curve againts each other (intrigues both their there values as a new curve of graph XY). This procedure is skipped when we equidistant curves, but here the data points are not in the same time positions, and also the number of them is not equal.

  How would you rate this conspiracy? I think about it, I could take the stamp of the first and last time in the two curves X values, and I would generate a table of new equidistant time stamp to cover the entire range (with a number of points which makes sense). After that, I have to do on the two original XY curves interpolation that transforms the original of the X values and be placeable on the new X positions.

  What would be the shortest way to do this in LabView? Or maybe someone has a simpler idea?

  Thanks for the tips!

  Edit: I guess the '1 D VI interpolate' is just what I need?

  Yes, so this is implemented, pls remove me wonder is trivial, I see now...

  All you need is to create a new ramp time (e.g. linear) that covers the two time slots at a sufficient resolution, then interpolate the two sets of data against it.

  Here is a quick sketch.

  

  Alternatively, you could also add the two original paintings of the time, sort and remove all duplicates to generate the new ramp time.

• How many curves can be traced on a tiara 2D graph

  Hello world

  I want to draw the curves of some(360+) on a 2D graph. I got the results for samples that are measured at different temperatures. I had no problem to trace the curves of all devices for a temperature. But what I noticed when I tried to trace the curves of all devices for all temperatures, it is that it does not work. Tiara (ver.10.2) gives an error if the number of curves is higher than 250, how is this possible? Is this a program limititaion which can be fixed with a patch or service pack, or I do something wrong?

  Thanks in advance

  Hi fscommand.

  From DIAdem 11.1, the maximum number of curves on a graph given in mode or REPORT is 250.  This has been the case for many years.  This restriction may disappear in future versions of DIAdem, but I do not expect it to disappear in the period of 2010.

  The solution is to overlay the 2 graphics, on the other.

  Brad Turpin
  Tiara Product Support Engineer
  National Instruments

• plot a point with curves

  With a unique problem of adding data point to group to draw curves.

  Suggestions?

  Are you trying to add a fourth field or add to an existing one? If you want a fouth field, you need to have the data in the new mathc cluster other clusters. This means make a table of each scalar. If you want to add this point to a parcel of exsiting and you must use the function Array to build on one of the x's berries - in the beam.

• How can I convert templates for tracing of Bezier curves?

  How can I convert models so that I can draw?

  Or if it is not possible for it in Illustrator, including ther plugins available for this purpose?

  TX

  Try to use the object > Expand

• Do curve a real - time of the linear adjustment computed

  Hi, here is how my program works:

  (1) plot data read from a file

  (2) user can move the sliders to select a range of data

  3) allows users to choose the scale with control 2 Y (Y minimum and maximum)

  (4) make a linear adjustment of certain data in real-time and gives the results.

  And there's no problem, I asked the graph xy of a while loop in which I drove

  (1) the function of fitting (selection of data to 2 inhabitants variable (cursors)) and table functions

  (2) local variable 2 (write) to adjust the scale Y with the number in the control.

  Data and sliders move user appear, all right.

  The problem is that I want to draw the fitted line of the xy-graph, so I did 2 x 2-number-table (with x = 0.1 and y = intercept, slope + interception) and...

  I must establish xy-curve in real-time to the Assembly line to refresh on a cursor move XD

  So I put the chart at the time, and I traced it each time the moment of the cycle (I used a condition with shift register to skip unnecessary calculation).

  And here's the problem: when the xygraph is traced the scale there is the default. A few ms then the scale will have correct (when the program has wide are the values of controls).

  Is there a way to avoid that the graph will go to scale by default when it is drawn again? Or is it possible to trace the line of editing without trace all the xy graph?

  Thank you

  PS: I tried to put a sequence stacked with paint 1) graph 2) scale but cen see you in any case the flash of the scale Y incorrect

  I think all you need to do is disable autoscale for axes.

  Overall, there are a few very complicated and very dangerous built code. Here is a small sample (are there many, many others!):

  The code on the left can blocking the program, for example if the data are all zero. Why is there a local variable? thread just from the source, it is just there! What you probably want instead of these small while loops is the array of threshold function. No need to loop.

  To write two properties, you use oven (!) property and three structures of sequence nodes deep stacked. Property nodes are running up and down, so all you need is the code below! Also note that 'table of index' is resizable. You don't need to wire the index unless you want something special.

  

• Waveform multiple graphics "bunk plots" with limits

  Hello world

  Here's my problem, currently I have 4 waveforms 'associated' with the "Build Array" function and connected to a waveform graph.

  I use the option "stacked plots" in order to have 4 curves with only a category axis.

  What I want to do is add a line of upper limit for each curve.

  Thank you very much in advance for your answers!

  Hi GoD_AsS,

  Use the classic palette tables. Make their border/background transparent and using a decoration as "frontier" for all 4 of them...

• Plot XY to polar trace

  The plot required is a polar plot to draw the objectives is to identify a radar detector. I traced a XY Chart with coordinates obtained remotely and measures of angles.

  I want to draw this positions X and Y in the polar plot. Source to the XY graph is a cluster of 2 elements while the connection to the Polar curve needs a picture 1 d of the cluster. The individual data are table 1 d of double and make a bundle does not solve the problem.

  Please let me know how to build the polar plot with distance and angle data.

  Kind regards

  
  

• Non-linear curve fit (distribution of blackbody radiation)

  Hello

  In my measurements I would estimate the temperature from the spectra of light emitted through the Planck law of the distribution of the black body radiation. I tried to get my data with non-linear curve fit, but I encountered some problems:

  1.) function is not properly, because of the distribution of different adjusted data form and input data values.

  (2) when tracing distribution of Planck by using the best shape parameter, the plot is different from the theoretical distribution of given temperature. (My data comes from the source of temperature 3100K, best setting made is 1130K, but fit is different from the theoretical distribution of 1 130 K)

  

  When I get a few simple equations, everything works, so I'm not sure of what could be a problem.

  Many thanks for any advice.

  Ivan

  Quickly, giving once more on this, it seems to me that one of your constant if four orders of large magnitude.

  You get a very good fit with 3.74177E - 16 instead of 3.74177E-12, see picture. (You divide your theoretical curves by 10000, but you aren't in your formula!)

  

• How to adjustment of the curve

  Is there a way to curve adjustments to data in number? This can be restored in Excel, but I don't see how making this number.  Polynomial curve get preference.

  Thanks for your comments in advance.

  Hi coop Mac,.

  Is that what you are looking for? Click on the series, then Format Panel > series > Trendline.

  

  The best graph I find for this is the Scatter Plot.

  Kind regards

  Ian.