6510 b upgrade memory is not recognized

Similar Questions

• Upgrade memory is not recognized on 4600

  I have now two 256 MB modules in my 4600 to give the maximum of 512 MB, but it is still not recognizing the amount previously installed 256 MB.

  I think I need to run "HALLOC/c" to rebuild the hibernation file, but I can't find a download of halloc.exe suitable for W2K.

  Is this correct, or is there something else I have to do to convince the additional RAM to be identified?

  Where can I download halloc.exe of?

  Thank you!

  Hi Jeff,

  You shouldn't have to do something specific for your 4600 to recognize the new RAM modules. The available RAM is checked/tested during the initial loading of the BIOS, so I would check in your BIOS that the correct allocation of the RAM is shown.

  If the BIOS shows that 256 MB while there must be a problem with one of the RAM modules or the housing itself. In this case try to exchange the RAM autour modules to see if the problem persists. You can also try starting your 4600 with a single module both installed to verify that the two RAM modules are working properly.

  Be sure to take of the anti-static precautions when handling your RAM modules.

  Kind regards

• Pavilion DV5 2050CA: upgrade memory does not not about DV5 2050 this laptop computer

  The upgrade of 2 x 4 GB 2x2gb memory does not work. After installing the new memory modules, it starts and the HP Quickweb are visible. As a result, if I try to load Windows 7, he returned to the screen of Quickweb. If I install only these new memories (1x4Go config), I get the error Badpool header.

  The NOTE book details are:

  Model - DV2050CA

  Produnt number - WQ748UA #ABC,

  2.26 GHz, Intel i3 - 350 M processor

  Max - 8 GB of memory

  Details of the memory module are:

  Kingston ValueRAm-2 x 4 GB, PC-10600 1333 Mhz, DDR3, SDRAM, CL9 SoDIMM.

  Can some please help me make it work?

  Yes, computers laptops HP prefer the variety of low density of memory. This means that 8 black blocks of memory on the side of the chip, not 4.

  4 GB 599092-001

  Above is the part number of HP for a 4 GB module.

  

  http://www.Amazon.com/HP-VH641AT-4-GB-DDR3-PC3-10600/DP/B0030L3B8E/ref=sr_1_1?ie=UTF8&QID=1446634397&SR=8-1&keywords=599092-001

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Card SD & Memory Stick not recognized

  Hello

  I have a Pavillion m9517c with the Athlon Phenom Quad-Core processor.  Initially, it came with Vista and when I got Windows 7 software, I installed it on a separate partition so that I can dual boot until I feel comfortable with Windows 7.

  Unfortunately, my cards Secure Digital or my Memory Sticks are recognized.  Is there a driver I can install will fix this?

  Thank you.

  Ron

  Try to uninstall and reinstall the drivers for the card in any case reader.

  Right click on the drives in the Device Manager, select uninstall, and then click OK.

  Once you have removed them both, get off at Bus USB controllers and remove any entries USB Mass Storage Device by using the same process.

  Once it is finished, right-click on any list in Device Manager and select "Scan for hardware changes".  It will redetect and reinstall the drivers for those devices.

• Satellite P200 - 144 Memory Stick not recognized

  Hello

  I have a problem with the memory card reader. Whenever I put a Memory Stick (MS Pro) is not picking it up. Happens to format the disk and when I try to format, it says disk cannot be found. If I push it just 3/4 km that it works.

  So I would like to know what is the problem?

  Have you also tried using other compatible cards?

• Satellite L755 - Flash USB memory is not recognized correctly

  Hi gentlemen

  I (ScanDsik 32 GB flash memory) she used to work properly, but last week it was late to work when I connect it to the laptop Toshiba Satellite L755 and now when I connect it I can't open it I see in Device Manager, but can not open and not properly recognize the flash memory is established in another laptop and computers only in my laptop now does not.

  I ve format into another one of these computers is Toshiba laptop too, I reinstall usb driver, but same, please could you help me?

  Have you tested the feature with others, like USB keys?
  Are you using the original OS that you got with your laptop?

• Satellite L300-229 - new module of memory is not recognized

  Satellite L300-229 - I just installed an extension of memory of 1 GB to add to the existing 1 GB.

  I used a 1 GB Crucial 200pin DDR2 SODIMM PC2 6400 CL6. For some reason, it will not recognize it and shows again that the 1 GB. I closed and installed in start mode according to manual and tried to reinstall.

  Any idea?

  Thank you

  Hello

  What happens if you only install the new module 1 GB RAM? Don't start the computer and if so how much RAM does show?

  Normally, the specifications of the new RAM module should work. I have a Satellite L300 too and I've updated it with the same RAM but Kingston. It works without any problem. :)

• Update in memory of not recognizing

  My laptop is supposed to take 2 GB of ram. I just upgraded the ram from 1 GB to guess what to be 512 MB of ram.  He showed only 448 MB of ram and still works despite the replacement of old ram and an upgrade.  I have a Dell Inspiron 1501 with Windows XP.

  BIOS shows the memory upgrade?

  If so, check this:

  Start-> Run-> Msconfig-Boot.ini tab-> advanced options >
  Ensure that the checkbox for the/maxmem = line is disabled and there is no value in the data area.

• Since Lightroom CC 2015 upgrade lenses are not recognized

  Since I upgraded Lightroom CC 2015 10 days there are lenses are most recognized in the EXIF data.  What can I do to fix this?

  Try to reset preferences: http://lightroom-blog.com/2015/05/23/resetting-preferences-in-lightroom-cc6/

• 460CDT: upgrade memory will not work correctly

  Hello

  I have 3 level of memory for the 460CDT updates:
  1 KTT500/128 (128 MB)
  2 PA2042U (128 MB)
  3 PA2040U (32 MB)

  PA2040U works without problem. Memtest86 without errors after 5 hours. KTT500/128 and PA2042U give me every time as many errors in test 5 [movement block, 64 moves]. The system starts with these memorys and recognize their work without error, but windows 98se unstable (errors, mistakes of recistry; a.s.o. due to lack of protection) someone who can help me?

  Hi Leo

  AFAIK the memtest is great and it works with very good accuracy. If there is an error message in 99% of cases the RAM module is defective. Please contact your local dealer and take a new one.

  Don t forget that your device can handle just with 160 MB of RAM. If you want you can also try to update BIOS.

  Good luck!

• No audio, cd/dvd devices does not work, can not update via Microsoft Update, usb memory sticks not recognized and much more

  The initial problem was no audio sound on CD.  The computer had other system sounds.  I uninstalled the Realtek drivers and downloaded from the website computer and reinstalled.  Still the same problem. I tried to adjust the volume control and clicked the speaker at the bottom on the right bar.  I got a message saying there is no mixer device and the small speaker disappeared and reappeared even after several reboots.  There is also an error "no audio device".

  After reboot, the computer gives this error message: "Generic Host process for Win32 Services has encountered a problem and needs to close." We are sorry for the inconvenience. »

  While trying to find a solution on the web, I discovered that the computer does not recognize the usb key,
  It won't restore to an earlier time,
  the CD/DVD drive will not run the data disks

  and Windows Update will not update.  The error message said: "the site has encountered a problem and cannot display the page you are trying to show."  There is an error number: 0x800706BE I tried to find this error message on the MS knowledge base, but it is not listed.

  The last Windows Update was on April 16, 2009 so I tried to restore to April 15, but it says 'system restore is not able to protect your computer.  Restart your computer and restart System Restore. "    After the reboot, the same thing happens.

  Any help is appreciated.

  The data is not "hostage." Pull the disk and put it in a box disc or it slave to a working computer and retrieve the data. If you don't have an additional computer you will need to borrow a friend or with the machine at a tech. You can also try the o with a Linux Live CD boot. I like Knoppix, but there are others. This has two advantages: 1) if the system works, you can back up all the data that missed your last backup; and (2) with the machine running Linux allows to determine whether the problems are caused by software or hardware. If the machine is unbearably slow and/or Linux cannot run correctly, you know that the hardware is at fault. If the machine behaves perfectly under Linux, you know that the software (Windows) is at fault.

  Whatever you do, do not install Windows without test material. If the hardware is at fault, software solutions like reinstalling Windows will be unnecessary. MS - MVP - Elephant Boy computers - don't panic!

• Tecra M3 (PTM30E) - new module of memory not recognized

  Hello

  I have a Tecra M3 PTM30E 09X01LEN and am trying to upgrade the memory - addition to the 512 MB, it came with.

  I bought an upgrade memory of 1 GB Toshiba - PC2-4300 DDR2-553 and tried to install it in the housing B (leaving the original card where he was). As far as I know I've followed the instructions in the manual (which is pretty poor, since it is just of the drawings), but the new memory is not recognized.

  What can I do else?

  Hello

  Strange but perhaps your new RAM module is defective or the second memory location.

  Have you tried the new memory module in the first place?
  What happens if you put the original 512 MB module in the second slot? The module is recognized?

  Check it!

• Compaq Presario SR5010NX: One of the two locations of memory not recognized / work

  Had already upgraded RAM from 512 to 1 GB.  In an attempt to level again with a 2nd (identical to the first) 1 GB DDR2 DIMMS, I discovered that the 2nd module of memory was not being recognized.  I also tried with success the new! G in the first taken.  Specification to support up to 2 GB with 1 GB DDR2 DIMMS in each shot. However, "no beeps" and not "start with anything in the second taken.   I also tried two 256 KB RAM modules and as the two 1Gs only the a 256 KB has been recognized.

  I also tried to boot with a module in the 2nd outlet only and found that my system wouldn't start.  Any suggestion would be appreciated.

  C001uS

  Thanks again for your response.  I went not the CMOS battery. However, your answer made me look on a possible revision of the BIOS through HP customer care.  I downloaded the version of BIOS the same but with a more recent date.

  After download and install I shut down my computer, insert the 2nd module of 1 G and made a new shoe.

  Happiness is a system of 2 GB Dual Channel now running.

  PROBLEM SOLVED

• After upgrading to itunes 12.5.2.1 my iphone is not recognized as a device in itunes

  After that I upgraded to itunes 12.5.2.1 and IOS 10 September 14 my 6s iphone is not recognized as a device if I sync my PC with Windows 10 on it.

  Help, please.

  Any body else with the same problem?

• Problem: Memory PCI Flash not recognized on Satellite M30X

  Hello

  Windows XP does not recognize my multicard reader. That he has still put memory PCI Flash not recognized (2 locations)

  I tried - uninstall the driver (and the camera) and reboot: does not work
  -install the cardbus driver: does not work either

  Have any hint?

  Mouk

  PS: Sorry for my bad English, I'm French ;)

  Hello

  Are you sure that the card is compatible with your laptop?
  As far as I know the card on the left site reader who, only available on some models, allows you to insert and read data from the SD card, smart media (SMM) MemoryStick pro, Multimedia card and XD picture cards.

  The PC card slot supports cards PCMCIA Type II