70 - noise of L IS 200 mm f4

Similar Questions

• Synchronization of the signal with PCI-6602

  Hello

  I need to generate three signals that must be synchronized.

  To do this, I use a PCI-6602.

  The first signal is used to trigger a device, the second signal is used to simulate the noise.

  The third signal should wear the noise so that it starts before the trigger signal and stops shortly after the trigger signal.

  The signals are then combined with an external logic circuit.

  (To see what I mean, see the first PDF).

  I use a fourth timer to synchronize all other clocks, but the three signals are beginning to run before starting the timer task. I have this evaluated using not to no and a oscilloscope.

  The trigger and gate (first and last signal) are below 100 Hz, the noise signal is about 200 kHz.

  At least the trigger and the door must be started synchronously, otherwise the waveform is not what we want. The noise signal didn't need to be synchronized.

  I am sure I am missing just a little detail here, maybe you can show me what I missed.

  Please check my screenshot of LabView to see what I've done here.

  If you want more information about the VI, I can take apart a little and send it, too.

  Try using start to the outputs of the 3 meter (see attached VI)

• filtering of noise over 200 kHz

  Hello!

  I'm recording ultrasonic vocalizations of rat at 1 ms/s using an acquisition of data PCI-6132.  One of my colleagues is ultrasound analysis of data from the records and asked me to apply a filter on the signal, as it is registered.  He asked the specifications was to "filter noise on 200kHs, with a steep slope.  I have no training in hearing analysis, so I have no idea what he's talking about, or how to impliment it.  Can anyone interpret this and help me understand this?  Thank you!

  Matt

  When I had to filter signals in LabVIEW, I had success with the express VI, called "filter". You can find it in the following range: "treatment-> conditioning of waveform of the Signal-> Filter.VI.

  Before we begin, I noticed that your condition is to filter "noise more of 200 kHz. This means filter any more than 200 kHz or just 'noise '?

  If you filter any more than 200 kHz, there are several parameters that you need to pay to reach your goal. Double-click the Filter.VI once you have he fell on the block diagram. The first thing you need to set is the same type. If you want to filter all above 200 kHz and spend everything below 200 kHz, you want a low-pass filter.

  Since this is a low-pass filter, you will have only a cut-off frequency. It's 200 kHz is your case, since you want to spend everything below 200 kHz.

  For a slope steep, I like to use the elliptical topology. You can start with an order of 3 to see if it produces the answer you need.

  I would recommend search filters on a site like Wikipedia, if this does not produce the results you need. Using this VI will take you where you need to go, but you may need to adjust the settings based on your signal. However, I think this will at least get you started in the right direction!

• HP LaserJet Pro 200 color M251: fact a LaserJet noise rattling to the power upward - OK or not?

  When I turn on the printer, it emits a rhythmic clatter or noise rattling for a few seconds. Is it OK or not?

  Hi @JayEll ,

  I see that you have problems with the printer by a clicking sound. I will definitely do my best to help you.

  I have provided a previous post with the instance, you can take a look at.

  Re: HP LJ 200 noisy m251nw the turning power on and off.

  I hope this helps.

  Have a great day!
  Thank you.

• SHOCK: X 200 noise (no fan) with different power settings

  Machine very quiet in general. But finding a question important 30 min after my hands on it:

  When I switch the power Off timers for setting, I heard very loud noise of current electric, close to the battery (upper part of the keyboard). I thought it was something unique to 'Timers Off', but towers was not released. I saw occasional same question with "Max Performance" / / "Energy Saver" etc.

  It is NOT the power adapter. He SPRING of the machine itself. Is not related to what you use the speaker or headphones. No partner that you were using the adapter right battery or sector.

  BTW, I just opened the box and did the Windows updates. No related software. No matter which firmware questions here?

  Any comments?

  Thank you!

  With the help of Mark, Lenovo responded effectively to try to resolve the problem. The technician and I think it is the LCD inverter noise. However, at least the special inverter we replaced the former with does not seem to solve the problem of my day 2 experience after replacing...

  The machine works fine except for this standby failure noises, Hibernate slow Vista Vista and sometimes.

  The noise recorded using the built-in microphone is like that. It does not systematically refer to the a/c adapter / battery use. Regardless of the CPU, video, ram, HD use.
  https://netfiles.uiuc.edu/xzhuang2/shared/noiseafter_inverter_replacement.WMA

  UPDATE: with the help of Mark, Lenovo finally sent in a replacement machine. The new machine seems to be free of the noise of the ups, at least for now. I hope that it was only an isolated case. Thank you, Mark!

• How my 200 x the fan noise disappeared

  Moderator note: there is no way to mark a simple/first post as "resolved." I moved belgam Hokkens to the 2nd position so it can be tagged accordingly.

  Thanks for the report.

  Z.

  Hi guys,.

  Like many of you I had problems with the fan is always on my x 200. For the first months, it was perfect and then for some mysterious reason, on that fan would remain all the time slowed down and changing the power mode would change nothing.

  Yesterday, after problems with a virus that manage to disable my version of AVG 9 and bypass the protection in real time from my version of Spyware Doctor, I decided to get rid of these 2 products. To replace them, I installed AVIRA free antivirus and Superantispyware version 4 (review and comments here) and after rebooting my computer, BINGO, my 200 x is completely silent still idling

  I thought I would share with you, I would like to know what are your experiences.

• How to deal with noise HDD G60T-200?

  My HP notebook (G60T-200) start bright one his noicy each time that the hard drive is active. How should I handle it?

  I think Toshiba is the a hard drive manufacturer that does not have a program available disk utility. Here's what they have:

  http://storage.Toshiba.com/storage-services-support/warranty-support/software-utilities

• Loud fan noise when runing Windows 8 on my Mac

  Hello to all the experts in Mac:

  I have recently installed Windows 8 with Bootcamp on my MacBook Pro (tecniques illustrated below) and when I start reading Microsoft Flight Simulator, which requires a lot of graphics, fans start to go very hard and the temperature is normal. Is there anyway to reduce the noise?

  Thank you

  MacBook Pro

  Processor: Intel Core i7-5557U CPU @ 3.10 GHZ

  Memory: 16GB

  Buffer: 512 GB (200 GB for Win8)

  The app is CPU intensive.

  Can I run Microsoft Flight Simulator X on my Mac?

  http://www.pcgamer.com/PC-gamers-Guide-to-gaming-on-a-Mac/

  http://www.Macworld.co.UK/feature/Mac/best-Mac-for-gaming-3446272/

  You can try to reset the SMC http://support.apple.com/kb/ht3964

• Satellite X 200-219 does not supply power to the top after intense use OpenGL

  After programming for OpenGL and a case of "slow BONES" for a few minutes, the screen is blank.

  I stopped him with force with the stop button and now there are no leads at all with battery or AC, it doesn't start at all, it is quite dead.

  It is certainly not the AC adapter, for who has not shown initially, it does not start a led and

  If the AC is connected, it's a very slight clicking noise and very light (must be the ear next to him to hear it, near the AC connector).

  Y at - it a hope?

  I guess it's a burned motherboard. I figured a burnt but GPU which would still leave at least cover LED or at least try to start up. Now it is completely dead.

  It's a TOSHIBA satellite x 200-219.
  There no guarantee, because it's more than 2 years since purchase.

  Hey,.

  I found some instructions here in the forum that you can try if the laptop doesn't start anymore:
  http://APS2.toshiba-tro.de/KB0/FAQ6201DK0004R01.htm

  It works for you?

• Satellite X 200 - 15 K power on but the screen is black

  Hello

  I have Toshiba Satellite X 200-15 K, two days ago, I have problem with screen, the screen I have noise, I think it's the same error in my display driver and I have stop near windows xp and try to after 1 min, but the screen has more noise when the startup boot image and I stop by button / stop on laptop.

  Then do what I ve tried again to turn on my laptop but on the screen, I see only artifacts (same squadrons of colors) and after that, my laptop can not work, I tried to power on him but I only power led and HDD light works only 5 sec and after off the coast, and the cooler works 5 sec too and after offshore.

  I tried to remove the battery and the RAM and the wireless and all that I can :), but nothing happens, but when I try to power without RAM I see on power light beep two red and two yellow (IE my motherboard work).

  Maybe it can help me. I think I have dead motherboard.
  And for me, it is interesting that someone may have similar problems.

  Thank you.

  P.S Sorry for my English :)

  Hello

  Let's summary.
  You had a few artifacts on the screen, and now, you are not able to start the unit.
  Nothing appears on the screen; Neither the Toshiba start screen appears is good?

  Hmm seems material issue I m thinking about GPU (graphics chip).
  What do you think of this?

  If it's really a problem of graphics card, then you will need to replace the motherboard.
  In most cases the chip belongs to the mobo anyway... something like this can be done by an ASP in your country.

  Then please get in touch with the guys to get more details about this

  I wish you good luck

• Satellite X 200 - strange sounds, close the cooler

  I have this x 200 for over a year now and for the last 10 days, I hear strange noises near the cooler which is located on the lower side right (the cooler in the cooler of the DVD).

  I don't know how to open this workbook for maybe clean the fan or Exchange it. It looks like a guide to disassemble for this machine.

  Thank you

  Sounds like the fan needs to be replaced.

  Is the system under warranty? I would send it to an ASP for repair. The X 200 is a complicated design and can be difficult/risky to pull out by the owners.

• Satellite X 200-191 issues, cause of software and/or hardware?

  I recently bought a Toshiba Satellite with windows vista on it... It has the following problems:

  -Sometimes the BSOD during his awakening mode standby via the keyboard or USB mouse
  -Static 'Plop' sound next to normal sound in windows Vista when you click on links or pause the video playback.
  -Artifacts (green and black jumps pixels) on the video play in 2d mode 'standard' ('resolved' by overclocking memory mode 2d by 50 Mhz clock)
  -Intermittent whistling electric flexible and hum from inside the laptop without connection with noise from the hard drive.
  -Light oozes out of the bottom of the screen.
  -Windows updates is not the first time, succeeding the second.

  on the other hand, it works very well... but it feels like I bought a second hand laptop I would stay there or are these common issues with x 200 with Vista on it?

  Hello

  To be honest, it's very interesting poster. After you use Windows XP Home edition for the years I also noticed some inexplicable phenomena on my laptop Vista P200 running. I don't really have any explanation why this happens, but I know for sure that Windows XP Home edition I never noticed anything like that.

  In my view, Vista is like a baby and this instability amazes me not at all. I'm afraid at the moment there is not much to do and just hope that after Vista SP1 should grow upward and more stable than now.

  What about strange noises or whistles? I'm afraid there is not much to say. You will live with him or you need to speak with technician and a clarification on the professional way. On the light is leaking from the bottom, I can say that it is normal and sensitive on each laptop with TrueBrite screen model.

• Satellite X 200 recent overheating

  Hi all

  I am have a 200 X - 20F for 10 months and recently, I find that the temperature are thermal Strawberry (95 ° for the processor) and 85/90 for the gpu to Burns before I ever above the 70/75 °

  I think that the fan are too slow, because until I heard a noise when I played and now I do not hear too much noise...

  I tried to run Toshiba, energy saving because I think that we can choose the rotation of the fan but this software doesn't start, I reinstalled the value added package, but I have the same problem.

  Is there a way too get my low temperature? Thank you

  First, check if there is any dust in the notebooks of cooling vents. If so, you can use compressed air jet to clean.

  If this is not the case, maybe you need to reinstall your display drivers. Just uninstall, reboot, install new, reboot and see if the laptop gets to warm up again.
  In addition, you can control the rotation of the fan with energy saver. You would need 3rd tools part to do.

• [X 200] MUTE button and bluetooth does not not after installing Windows 8

  Recently did an upgrade on Windows 7 site to 8.1 and have pretty much everything works except the button mute and Manager connections (and thus bluetooth). I tried to install the latest driver button support page for Windows 8 X 200, and while I saw him appear in Device Manager after you restart, it made no difference. Also, the noise stopped working during this time. I uninstalled driver buttons and brings the sound back, but I still want to get buttons will still once (and the connection manager).

  Any ideas?

  Thank you.

  After much experimentation, I solved the problem. The problem is caused by the integration function Hotkey not installing pack is not right. The most recent version on the assistance of the X 200 (version 3.89.0100) page is over (at least for Windows 8). When you try to install it, it will not yet to present the possibility of installing the highest importance "pilot interface system. To resolve this problem, there are a few things. First of all, I uninstalled what I call the "ThinkPad features Trio"-this is the Hotkey integration pack, power management driver and the driver of tablet buttons.

  After uninstalling and rebooting the computer, we can start fresh. To get things working properly, I installed the old Hotkey integration Pack (version 3.52, us.driverscollection.com, look for links to download fake of course), rebooted, installed the driver of power, restarted and finally installed the previous version of the Tablet driver management buttons I used with Windows 7 before, followed by a final reboot.

  This combination gets all the buttons (mute, Fn + F5, the buttons of the tablet) and features OSD works 100%. The only negative side effect is that Windows 8 has its own bar of volume on the screen when you change the volume with the buttons, so you will see both the bar and the Lenovo one native. It seems a bit funny, but they overlap or anything like that, so I'm fine with it.

• X 200 hard drive change

  I have a 200 x, with as a hard drive 7BG. It is very quiet in the State, but I want to trade for a big drive. So my question is; is the factory installed lenovo hard drive it yourself it's very quiet or pampens sound laptop case? If it is that silence is due to the hard drive yourself, what none of yo recommends an update on the same level of noise?

  Lenovo readers are just general drives, usually Seagate or Hitachi, both decent. Sensitivity to noise is really personal, so it is difficult to comment on the limited description that you provided. Personally, I can feel the noise of Seagate 5400 RPM 250 GB spindle, which does not exist on a 5400 RPM 80 GB WD I (when I swap in X 200, so the two disks are installed in the same way).