8.1 Windows password not recognized after updates

Similar Questions

• Satellite Z30 - A - 12R BIOS password not recognized after update BIOS

  I updated the bios after that I warned the Bios of Toshiba v3.50. The process was done by the utility software of Toshiba and after restarting it has 'password =' on a blank screen and it does not recognize my BIOS password, write not 'certified '.

  I also tried the HARD drive password, but no luck.

  What can I do now?

  Hello

  Before you try to update the BIOS, all passwords must be removed!
  BIOS password can be removed by the authorized service provider available in your country.

  But the unknown HARD disk password can be removed more.
  In such a case the HDD isn't accessible and cannot be used.

  Mate sorry but in my opinion that you only have one chance to get the BIOS password removed. you need the help of ASP.

• G570 bluetooth not recognized after update to 8.1 windows

  This is a very unusual problem, and I have not found one post on this anywhere!

  First of all my specifications specifications

  Lenovo G570 (reference number: 43345JU)

  i5 - 2410M

  8 GB RAM

  Qualcomm-Atheros AR9285 WLAN

  do not know the brand of bluetooth (for most broadcomm)

  Provided with Win7 Home premium x 64

  The Win7 it came with also had lenovo energy management through which I could toggle the WIFI and bluetooth on and outside. Given that I've never used the bluetooth, I turned it off via Power Mgmt.

  Interestingly, when I was running Win7 I also had this dual boot with Ubuntu. And if my Bluetooth has been disabled through the win7... EM bluetooth wouldn't be recognized in ubuntu and there was no way to turn it back on... I had to start again under win7 and turn it on via EM and start in ubuntu.

  Recently, I updated to Win8.1 but had not put on the bluetooth before doing so. In Win8.1 bluetooth device is not recognized everywhere... no PC settings (metro UI), not even in Device Manager. I tried to install the energy management to 8.1 from the support site, but he was extremely buggy and found no option to activate bluetooth. The old EM has not installed correctly in comaptibilty mode.

  In ubuntu now (dual boot with win8.1) its still the same. Bluetooth not regonised just like before.

  I can't go back to win7 now. There is no correct EM to win8.1. There is no option in the BIOS about bluetooth.

  How can I activate the bluetooth adapter? ANY help is appreciated...

  Hi neokenchi,

  Please help out me. Yes, I had tried to install win7 EM but trotted in compatibility problems. But now started digging through the forums and found a link to EM that works on win 8 and 8.1 of victory. It has even installed the power controller driver virtual lenovo APCI.

  http://driverdl.Lenovo.com.CN/Lenovo/DriverFilesUploadFloder/36900/WIN8_14.EnergyManagement.exe

• Windows does not start after update

  Stop PC last night and let it install 3 critical updates at shutdown. On the PC this morning, it won't start. Repair of the system indicates it cannot automatically repair...

  Restores the auto system restore point before the decommissioning, and it now boots normally...

  Then, Mr. Gates, who, following updates kills my PC? :::

  Update security for Windows 7 (KB2419640)

  Download size: 857 kb

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  A security issue has been identified that could allow an unauthenticated remote attacker to compromise your system and take control. You can protect your system by installing this update from Microsoft. After you install this update, you may have to restart your system.

  More information:
  http://go.Microsoft.com/fwlink/?LinkId=204803

  Help and Support:
  http://support.Microsoft.com

  Update for Windows 7 (KB2454826)

  Download size: 4.7 MB

  You may have to restart your computer for this update is taken into account.

  Update type: recommended

  This is a reliability update. Install this update to enable a set of performance and features updated graphics, Media Foundation and the XPS components on Windows 7 systems.  After you install this item, you may have to restart your computer.

  More information:
  http://support.Microsoft.com/kb/2454826

  Help and Support:
  http://support.Microsoft.com

  Update for Windows 7 (KB976902)

  Download size: 4. 3 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Install this update to enable future updates to install successfully on all editions of Windows 7 or Windows Server 2008 R2. This update may be required before you can install the selected future updates. After you have installed this item, it cannot be deleted.

  More information:
  http://support.Microsoft.com/kb/976902

  Help and Support:
  http://support.Microsoft.com

  Windows malicious software removal tool - January 2011 (KB890830)

  Download size: 999 KB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  After the download, this tool runs once to search your computer infections by specific, prevalent malicious software (including Blaster, Sasser, and Mydoom) and remove infections found. If an infection is detected, the tool displays a status report the next time that you start your computer. A new version of the tool will be offered each month. If you want to manually run the tool on your computer, you can download a copy from Microsoft Download Center, or you can run a version online from microsoft.com. This tool is not a replacement for an antivirus product. To help protect your computer, you must use an antivirus product.

  More information:
  http://go.Microsoft.com/fwlink/?LinkId=39987

  Help and Support:
  http://support.Microsoft.com

  This thread seems to describe the problem you are experiencing:

  Windows 7 - KB2454826 fails and only recover after reboot

• This copy of Windows is not genuine after updating Windows 10 and return to Windows 7 Ultimate

  When I've updated to windows 10 using the windows icon free 10 in the corner, it didn't appeal to me, so I used the button restore to go back to windows 7. After he turned back, a saying watermark "Windows 7 Build 7601 this copy of windows is not genuine" I don't know what happened and only happened once I started windows 7 Windows 10. Someone help please!

  I suggest that you run the diagnostic tool Microsoft Genuine Advantage in normal mode and copy and paste the results into a response for further analysis:

  http://go.Microsoft.com/fwlink/?LinkId=52012

  Run the tool and when it ends, click the copy button, open a text such as Word or Notepad file and select Edit, paste. You can paste directly into an answer here. Open a response, right click and select Paste.

• Pencil of Apple not recognized after update 9.21

  Hi guys

  9.21 yesterday on my ipad pro upgrade and now its telling me my apple pencil is not certified and not recognizable. It won't register for matching and will not charge because it is not recognized. Can someone tell how can I solve this please. I bought the ipad pro and apple prncil directly from apple.com when it was first released.

  Hoping someone can help

  Try a hard reset of your iPad by simultaneously pressing buttons Home and sleep/wake button until your iPad goes to the dark and restarts with the Apple logo, then release the buttons.

  Good luck!

• Windows does not load after update

  I just installed windows vista on my calculation, after that I return it. I had to reinstall windows and every time I do the windows update it restarts and when it turns back all that I get is a black screen with nothing load on this subject?

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  Windows Update Forum:

  It comes with Vista, upgrade install and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• WRT160NL Usb storage not recognized after update firmware

  Hello.
  I use a power running alternative disc into my router for a long time, until I've found the new firmware (Ver.1.0.04 Build 2), but after the upgrade of the storage was no longer working. (I don't remember the firmware version he had)

  In the storage, in the page Setup tab, I can see the drive, I can create shares, but these are not present in the windows network. (I use windows 7)

  the disc has been tested using FAT32 and NTFS (232.8 GB)

  you have a solution for this problem? or should I return to the firmware version, he had (that I don't remember)...
  y at - it another version to switch to?

  Thanks for your help...

  Yes! This is the solution!

  Thank you

• Windows does not start after update, but starts in safe mode

  last night my laptop set to day, I turned it off and when I started today he went straight to the safe mode selection screen. I chose to start in normal mode where it just went to blue screen, just a flash so I couldn't read what is on it and then restarted itself. I then chose safe mode with network boot and he finished making the update without problem, so I rebooted and tried to start up normally, but still it restarted itself, so I went back to safe mode which is what Im use it as today.

  as far as I know that it does not crush power or coward during the update and cannot think it's updating itself that causes the problem. Ive tried to do a system restore but it says theres no restore to restore points.
  Can someone please help me because running in safe mode is maddening as theres no graphics driver and the resolution is horrible.
  Thanks in advance
  Hayley

  Maybe a start of repair:

  http://Windows.Microsoft.com/en-AU/Windows-Vista/startup-repair-frequently-asked-questions

• Windows did not start after update of the Service Park 2

  Update Windows Installer service Park 2 but my system could not start. I do restor system but cannot start windows.

  There is a free Microsoft support when it comes to updates:

  https://consumersecuritysupport.Microsoft.com/default.aspx?ProductKey=pcsafetyupdatesnotinstalled&task=country&St=1&wfxredirect=1

• 8.1 Windows does not start after update

  I saw this mornong that Microsoft had applied an update and when I rebooted, it would not start. I get the screen repair with all the options and I tried to run/r Chkdks and he found no errors and also tried to use several restore points and they would not restore. I tried to alkso startup repair without success.  Any suggestion?

  I advanced and gritted my teeth and I'm back to Win 8. Almost finished making things to normal.

  Thank you

• Pavilion p6210t: CD/DVD HP Pavilion p6210t drive is not recognized after upgrade Windows 10

  HP Pavilion p6210t DVD/CD drive is not recognized after the upgrade to Windows.  DVD/CD material is: LightScribe16XmaxDVD + / R/RWSuperMultidrv.  I can't find an updated driver for this device, download and install. Thanks for any advice you can provide.

  Thank you for your response.  I can't find somewhere - it now despite a lot of research - I read on a very simple solution to this problem which is (was) affecting hundreds of users HP.  In essence, the solution said that the DVD drive has in fact been recognized [as evidenced by his appearance in the BIOS] but has been "identified" and how to fix this problem was to go into the DEVICE MANAGER and delete the incorrect identification reference - then restart the computer and Windows 10 would correctly identify the DVD player and correctly in the DEVICE MANAGER list.  I decided to try this simple fix before one of the more complex solutions that were offered.  The simple solutioon worked! 

• Windows login password not recognized

  Original title: sign the password not recognized.  Similar problems are are produced.

  Already happened.  Tried to sing in password rejected.  It's the same thing and I him have not changed for a long time.

  Log on to another administrator user account and change your password to something that you will remember. Then search for malicious software because these things do not happen by themselves. Or think about who else has access to your computer and may have changed your password without your knowledge.

  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  If you have another administrative user (see Configuring user recommended at the end of this post) and then you have to activate the built-in Administrator, and then change the password of your user account. All this requires a certain level of computer skills. You know better and that take the machine to a competent local computer tech (not a type of BigComputerStore/GeekSquad place) is the best solution for you.

  If you have a Windows 7 DVD installation (not a recovery DVDs), you can start the system with it. Select the default language, then select "repair your computer". Then select "Command Prompt". At the command prompt, type:

  NET user administrator / Active: Yes [press Enter]
  NET user [insert here the name of your user account] [insert the new password of user as 1234 here] [press Enter]

  [Note: do not enter the brackets!]

  Remove the installation DVD and restart the computer. Now, you will be able to connect to your user account by using the password that you set; for example, 1234.

  If you do not have a Windows 7 installation DVD (only have a recovery disk), the computer mftr. may have given you the option to repair the system Windows 7 (not a system recovery!) in the menu diagnosis. This menu of diagnosis is the same one where you can choose Safe Mode. Get to this menu by repeatedly pressing the F8 key as the computer starts. If you do not have this option, you can make a bootable DVD of Windows 7 repair of the file on this link:

  http://NeoSmart.net/blog/2009/Windows-7-system-repair-discs/

  Note: All the Neosmart recovery disk downloads are torrent files. There is a good explanation of the torrent on the site Web of Neosmart files. You will need a torrent asmuTorrent client to get the files. Torrent client will download the .iso file with which to create the bootable DVD. If you create the bootable DVD in an older operating system (XP, Vista), you will need to use third-party burning software such as Nero, Roxio or the free ImgBurn (http://www.imgburn.com ) to burn the image .iso image file, not in the form of data. Windows 7 can burn the .isos natively.

  Once you have fixed things, log on to the additional administrative account you will be made by the suggestions below and disable the administrator account integrated yet for security reasons:

  Start Orb > Search box > type: cmd
  When cmd appears in the above results, right-click and choose "Run as Administrator" [OK]. Now, you will get the command prompt. At the command prompt, type:

  NET user administrator / active: No. [Enter]

  Exit the command prompt.

  General recommendations for creating users in Windows 7:

  You absolutely don't want to have only one user account. Like XP, Vista and all the other modern operating systems, Windows 7 is a multi-user system with integrated system of accounts as default Administrator and comments. These accounts should be left alone because they are part of the structure of the operating system.

  In particular, you do not want account only one user with administrator privileges in Windows 7 because the administrator account integrated (normally only used in emergencies) is disabled by default. If you use as an administrator for your daily work, and this account is corrupt, things will be difficult.  It is not impossible to activate the built-in administrator to rescue things, but there may be more that you want to do. Better not to put you in a bad situation at first.

  The user account that is for your daily work must be a Standard user, with the extra administrative user (call it something like 'CompAdmin' or 'Tech' or similar) only it for elevation purposes. As a user Standard is recommended for security reasons and will help protect your computer against infections. After you have created "CompAdmin", connect to it and change your normal user account Standard. Then log on to your regular account.

  If you want to go directly to the desktop and ignore the Welcome screen with the icons of the user accounts, you can do this:

  Start Orb > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  MS - MVP - Elephant Boy computers - don't panic!

• ASUS laptop computer: touch screen does not work after update of windows 10

  My touch screen does not work after update of windows 10 in Chrome. How can I fix it?

  Hello

  Welcome to the HP support forum. Asus and Chrome are not HP, touch screen works on my machine HP with IE, Firefox and the new browser Windows 10 called Edge. I think that you need to update to Chrome.

  Kind regards.

• Ethernet USB adapter does not work after update to sierra mac

  Ethernet USB adapter does not work after update to mac sierra.

  Please solve this problem as soon as POSSIBLE

  Hello guatamshah,

  If your USB to ethernet adapter does not work now that you have upgraded to Mac OS Sierra, there are a number of things we can try to get it working again.

  The first thing we want to do is to reset the SMC and the NVRAM on your Mac.
  Reset the management system (SCM) controller on your Mac.

  https://support.Apple.com/en-us/HT201295

  How to reset the NVRAM on your Mac.
  https://support.Apple.com/en-us/HT204063

  If the adapter is not still work after only two resets check to see if your Mac recognizes the device properly in the information system. In the Apple Menu, choose about this Mac, and then click the button 'system report... '. ». Once you have the window open system information, see the USB category on the left.
  OS X: about system information and System Profiler

  https://support.Apple.com/en-us/HT203001

  If she does not appear in the information system, see the articles below.
  macOS Sierra: If a USB device does not work

  https://support.Apple.com/kb/PH25343

  macOS Sierra: check your device's USB connection

  https://support.Apple.com/kb/PH25567

  However, if you do not see the device in system information, you may need to verify that network service appears correctly. In the Apple menu, choose system then Network preferences. You should see an entry similar to "Ethernet" on the left. If no, see the steps in the article below to add. Once add, test to see if your connection works with a disabled Wi - Fi connection.

  macOS Sierra: Add a network service
  https://support.Apple.com/kb/PH25279

  If it does not appear in the network, please let us know what you see on the right when you select the service, and the name of the service as it appears and we can go from there!

  Kind regards.