8.6 RT works with Labview 8.5?

Similar Questions

• How to install the version of nor-Sync 3.1 in the remote system (processor integrated PXI chassis) to recognize the PXI-6682 device to work with labview RT?

  How to install the version of nor-Sync 3.1 in the remote system (processor integrated PXI chassis) to recognize the PXI-6682 device to work with labview RT?

  Hung Nguyen

  Hung Nguyen,

  The installation of drivers for all targets in real-time remotely is more or less the same. First install the driver (in your case the NO-Sync) on your PC, then install it on your system remotely through MAX. For step-by-step instructions, see install the software on your NI CompactRIO controller.

  See you soon,.

• Does anyone have a DSO - 2090 Mory working with labview

  Hello

  I have a DSO-2090 Mory which I can't seem to make it work with the provided labview VI. I searched the Board, but have not yet found one another answer that it probably has something to do with the function in the DLL. I have no way to change the dll function so I need now to see what I can do. I walk if someone else has used this DSO before and if so how in the world do you have running? I appreciate all suggestions and advice, other than to get a new dso because this is the one I'm stuck with for now.

  Thank you

  Hey all,.

  It seems that I now have a solution. I contacted Mory and I think it took about a week for them to get back to me, if once they have come back to me, I could start to compuniating back with a tech. The tech sent me another copy of the Vi along a copy of the dll which seems to work.  So I attached the vi but I can't join because of its extension .dll file, so I changed it to a .doc file that will need to be renamed with .dll incase anyone else ends up with the same question.

  Thank you all for your comments.

• The jury of ELVIS will work with LabVIEW Student Edition 2010

  Hello

  This question was asked in the forums of LabVIEW, but no solution has been found. I have a windows 7 x 64 machine with LabVIEW 2010 Student Edition. When I try to install ELVIS 3.0.5 traditional software I get the following (no error code) message: "this Setup program requires the LabVIEW 8.5 development system or later to be present on this computer. Development system LabVIEW Base in any version of LabVIEW is not supported. Please install LabVIEW and then rerun setup of NI ELVIS. »

  I also installed the DAQ software for PCI DAQ board. I do not have access to a 32 bit machine and do not know how to get my board work (no ELVIS II) ELVIS. I have provided a screen shot of the message during the installation of the software of ELVIS.

  .

  Hey dduong16,

  Thank you very much for taking the time to provide additional information. After talking with several experts about your system, we concluded that this error is the result of an incompatibility between 3.0.5 Elvis and LabVIEW 2010 64-bit. Even the latest drivers of Elvis are not yet supported by 64-bit LabVIEW: see notes in support of the operating system on the Readme Elvismx 4.2.3

  To solve your problem, you will need to uninstall the 64-bit version of LabVIEW and install a 32-bit version. If you are a student, you should be able to get this version of your computer (it will work fine with your Windows 7 64-bit OS - it will install on 32-bit OS emulated inherent in your system). If you are not a student, please send me a personal message, and we will be working with an account representative to get you the necessary version.

  I apologize for the inconvenience, this made you and appreciate your patience. We have updated the Elvis 3.0.5 Readme to reflect this incompatibility (the change may not appear yet, because it takes time to propagate through our system), and I'm trying to create a Base of knowledge on the subject article to help future users who encounter this error.

  If there is anything else that I can help you, please you after return. Thank you!

  ~ kgarrett

• HELP - FPGA SPARTAN 3E-100 CP132 WORKS WITH LABVIEW FPGA?

  HI EVERYONE, GET ON IM TRYING TO USE MY FPGA WITH LABVIEW, BUT I DO KNOW THAT IF ITS COMPATIBLE, I INSTALLED THE DRIVERS, MODULE FPGA AND LABVIEW 2012, IM USING WINDOWS 7 32 BIT, AND AFTER I COMPILED ITS SAYS:

  LabVIEW FPGA called another software component, and the component returned the following error:

  Error code:-310601

  NOR-COBS: Impossible to detect the communication cable.
  Check the communication cable is plugged into your computer and your target. Also, verify that the proper drivers are installed.

  Thank you.

  =)

  Hi dvaldez2.

  LabVIEW FPGA offers no support for any material to third parties, other than the 3rd Spartan XUP Starter Kit. These are probably the drivers you downloaded.

  http://digital.NI.com/express.nsf/bycode/Spartan3E?OpenDocument&lang=en&node=seminar_US

  However, this driver supports only the Starter Kit Board itself (http://www.digilentinc.com/Products/Detail.cfm?NavPath=2, 400, 790 & Prod = S3EBOARD). You may not use the driver with any other Xilinx FPGAS.

  I hope this helps.

• In time real PXI-1031 does more work with labview. "Not enough disk space to perform the backup.

  The labview real-time project was working until a few weeks ago and the only error that is displayed on the PXI is this error message.

  "NEITHER Configuration Manager: not enough disk space for the backup" everything before that looks like it starts very well. Recently, I removed the hard drive and remove the 4 GB network log file because it seemed to me that a file of 4 GB on a fat32 file system was probably the cause of the problem. After that it the project worked when I tested it, but others in my lab said it was broken again the next day.

  Any help would be greatly appreciated because I don't know all that equipment.

  I found that I had "reset IP" set to "yes" in the bios that seemed to be causing my problem because I changed it to no and it seems to work perfectly now. Sorry that it took so much time to understand and I feel like a fool.

• Screenshot VI works fine with Labview 9 but crushes with Labview 10

  Hello world

  I'm using Labview 10 with XP.

  Screenshot VI (available in the .zip in this discussion http://forums.ni.com/t5/LabVIEW/Can-i-make-an-automatic-Print-screen-in-labview/td-p/534790/page/2?q... works very well with Labview 9 but makes Labview 10 crush every time (same computer).)

  Any solution to make it work with Labview 10?

  Thank you

  User

  Hello

  Thanks for posting on the forum of NOR.

  You can find an answer at the end of the same link you post (page 4).

  http://forums.NI.com/T5/LabVIEW/can-i-make-an-automatic-print-screen-in-LabVIEW/TD-p/534790/page/4?q...

  Kind regards

• Is DAQ Measurement Computing USB - 1608FS compatible with labview?

  I have DAQ USB-1608FS from Measurement Computing company, and I was trying to see if it is possible to use

  This data acquisition with labview 2012. I tried to download the drivers from their company http://www.mccdaq.com/usb-data-acquisition/USB-1608FS.aspx

  but when I tried to use labview in the DAQmx the DAQ tool is not detect it by LabView. So, if anybody out there knows if this data acquisition

  really can work with labview, please let me know.

  Their driver seems to be ULx http://www.mccdaq.com/daq-software/universal-library-extensions-lv.aspx

  and he said that he supports LabVIEW 2012. I suppose you open a sample and the device does not appear? The device is displayed in the Windows Device Manager? It seems that this driver/device will work, there may be just a few questions it initialize properly on your machine (either with Windows or Measurement Computing software). You must be to open a debate on their forums or call their support help line.

  Good luck! Let us know some of the above and, of course, let us know if find you the solution.

  -gavin

• Raspberry PI connected with usb for laptop with Labview

  Hello

  Please allow me to introduce myself: my name is Bob and I just graduated from the Bachelor of applied science (Physics), in the Netherlands. In education, I followed a course of programming in Labview. However, the course was not very well if I want to start from scratch. (my programming skills are very poor).

  My goal is to learn the basics of programming in Labview. I want to measure the temperature with a probe for example and read this in Labview. I need a data acquisition for this system. I have a raspberry PI in my possession and I was wondering if I could use it to read the temperature from the USB port of my laptop using the PI raspberry. Is this possible? And I have to run some sort of program on the raspberry PI? Or I could better use another device (Arduino maybe?).

  I hope someone could help me to help me get started with Labview. I'm looking forward to learn how to work with Labview and launch a few projects.

  Thanks in advance,

  Bob

  Are you comfortable with writing code on the invoice, pro forma raspberry? This is where you write the code for the acquisition of data and code to send it on the usb as a RS232 serial port. The LabVIEW program would receive all this and it is a very simple program. There is a tool called Linx box that does all this for the arduino.

  https://www.labviewmakerhub.com/doku.php?id=libraries:Linx:start

• Application errors of the RT with the PXI-4461 with Labview real-time 9.0.1, DAQmx 9.0.2

  HI -.

  I recently converted a PXI time system real OS (PXI-1042 q chassis, controller PXI-8187, DAQ, PXI-4461, DAQ, PXI-6259). I can write and run DAQmx applications in real time with the 6259 very well. Whenever I try to write a labview RT app to use the 4461, however, it will fail. Note that I can use two cards through MAX I tried switching card slots, just in case it was a problem. Both cards worked with labview, the PXI chassis was before Windows.

  Attached are pictures of the screw base demo I built to show the problem. Since I was a mistake (-200758) if I started from the raw strings, I tried to create a MAX task and use it. The task, but he complained of a buffer is too small. I explicitly put the buffer to work around this problem and still get the same error (-200608). I've also attached a screenshot of the software currently on the Max MAX RT PXI system is version 4.6.2 btw. (I installed the most/all this from DS1 Dev Suite 2010 version).

  Please let me know if I hurt something installed, versions if 4461 just don't play nice with the new BT or RT software, or if something is wrong. Thank you.

  Kregg

  The first error you see is (details in the help-> error explain in LV)

• Can LabVIEW Embedded for ARM works with any Board or just with a few predefined?

  Hello

  Can LabVIEW Embedded for ARM works with any evaluation committee or just with a few predefined (MCB2300, MCB2400 and EK-LM3S8962)? I ask this question because even if I chose "another processor" in the definition of the new project only 3 options are the corresponding arm of Phillips and LuminaryMicro.

  Thanks in advance,

  Howdy,

  LabVIEW for ARM supports the feature of targets for tier 1 (the mentioned Evaluation Committee) following this schema:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/7066

  But you can transfer to other weapons if you follow this porting guide:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/6994

  The uProcesser SDK is intended for the port of other targets of DEPENDENCE (32-bit, of course) and technically it covers ARM as well. Alternatively, there are the LabVIEW C Code Generator: http://sine.ni.com/nips/cds/view/p/lang/en/nid/209015

• Get incremental counter/sound to work along side with action with usb-6008 with labview tia sal22

  Get incremental counter/sound to work along the coast with usb-6008 with labview tia sal22

  Hi all

  I can get this vi to work if they are distinct from the vi but I can't join them together

  Example of my error:

  If buffers are set to 0 the freq counter increment works, but no sound
  If the buffers are set to 1 the audio works fine but is not increment the Freq counter
  If the buffers are attached to more 1 clicks and pops are coming

  That's what I'm doing:
  (1) have the frequency of increment of my internal sound card to a certain level as .01hz a second until he gets to 20 000 hz

  (2) use my device usb-6008 daq, which is connected to the same machine to measure the voltage at the same time. (I am in a position very low voltages between 1-5volts)

  (3) output to a worksheet text file which will show you:

  time in seconds, frequency, voltage
  0,400.01,2

  1,400.02,2.5

  2,400.03,1

  I'm a bit confused about how connect the increment and the audio during the measurements with the usb-6008 housing on the same machine
  at the same time and in the same VI.

  Anyone have any ideas?  I'm using labview 8.5
  TIA sal22

  Ha ha you have been deceived by a dynamic thread. Insert a convert from Dynamic Data Express VI (Palette to own: Signal handling screw Express) between the daq read and build the array function. Then it won't work. Now the value in the dynamic data is only converted to a numeric value

• Can query serial port with NI MAX, but does not work in Labview

  I'm controlling a 488 Sapphire consistent with labview. It is connected by a series of converter USB in the computer. I can communicate with a device using NI MAX, but when I try to run the vi (attached), he works for multiple queries, but evetually returns a null character, after which I can no longer communicate with the port. If I then go into the NI MAX interface, whenever I try to read it give "VISA: (Hex 0xBFFF0015) timeout expired before the operation ended" error message. There are also several queriess of the manual of the instrument which do not seem to work at all (with or without MAX) and always returns a null character. Any help is appreciated. I'm definitely a novice with the communication of the device. Thank you.

  Usually a problem with the stop character.

  And you send-r and no CarriageReturn.

• LabVIEW 8.6 will work with windows update to win7?

  company is updated to Windows XP to win7. Currently, we use labview 8.6 version. LabVIEW 8.6 will work in win7?

  Thank you

  Yihan

  http://digital.NI.com/public.nsf/allkb/A45AD60ED0A571C28625766B005859D2?OpenDocument

  This thread: http://forums.ni.com/t5/FieldPoint-Family/NI-software-hardware-compatibility-with-Windows-7/m-p/1857...

  Single LabVIEW 2009 and later are officially supported on Windows 7.  However, some older versions of LabVIEW work with Windows 7.

  I installed it at home on a win7 x 64 machine at home, and it "seems" to work very well.

• Working with USB high speed Interface Modul 2.7 in LabVIEW

  Hello

  is there an example works with a USB high speed Interface Modul 2.7 in LabVIEW?

  The EGG is a "Cypress CY7C68013A-56PVXC»

  Thank you

  Best regards, patrick

  Hi patrick,

  I searched on google for the module. The manufacturer is Braintechnology.
  If you need a LabVIEW driver ask them please, maybe it's that they can provide you with a.

  Braintechnology offers a DLL - USB. With a little work, you can include this dll in your LabVIEW project (call library function node).

  The following documents explain how to:

  Integration of external Code with the Shared Library Import Wizard (requires a corresponding header dll)
  http://zone.NI.com/DevZone/CDA/tut/p/ID/2818

  Writing Win32 dynamic link (dll) libraries and qualifying of LabVIEW
  http://zone.NI.com/DevZone/CDA/tut/p/ID/4877

  Example: Passing a variety of Data Types in the DLL for LabVIEW
  http://zone.NI.com/DevZone/CDA/EPD/p/ID/1288

  Kind regards
  N. Ralf
  NIG.