8 to 8.1 upgrade of windows problems

Similar Questions

• 630 HP: HP 630 - upgrade to Windows 10 - Wifi problem

  Hi all

  completed the free upgrade to WIndows 7 Home to 10 Windows. This is done via Ethernet NIC - all filled with success - activated license. After I clean install and once again everything seems fine - except when I tried to use the WiFi. There is a red cross on it and it cannot detect all networks. Setting-does not react. Only thing it does is switch or disable airplane mode by pressing the button hardware or software.

  Of course the driver problem. In the Device Manager WiFi shows as Aetheros AR9285 and there is no warning - operation normally. I tried to consult no HP site for the product but in fact there are just the Windows 7 driver that can not be installed as Windows 10 says this isn't for this version of the operating system.

  So I tried to download directly from Aetheros https://www.atheros-drivers.com/atheros-wireless-drivers.html. Downloaded AR9285 for Windows 10 (no exe just inf files etc.) and installed it via "update driver". Not completed successfully, restart done but always the same - no WiFi - impossible to enable it in Windows.

  Anyone have this laptop and know which driver to use?

  so, finally I managed to find a solution on some Linux forum:

  -Remove the battery

  -Go into the BIOS

  -F9 to reset to the default values

  -F10 to save and exit

  WiFi works again.

• Satellite L730 - Bluetooth problem after upgrade to Windows 10

  Hello. I use a portable Satellite L730 and the only thing that would prevent me from upgrading to Windows 10 is the problem of Bluetooth. RFHID, RFCOMM and RFBUS will not work properly because there are no drivers. Apart from that, the computer there is no requirement of meeting problem Windows 10.

  So is it possible that a sollution to this problem will be provided anytime soon?

  Hello

  In most cases, BT does not work due to lack of BT software.
  The point is that most laptops use a module for WLan and BT.
  This combo module WLan/BT requires additional driver filter...

  According to your WLan / module BT, you will need to install the filter for the BT driver package.
  In most cases the 8 Win / filter package 8.1 Bluetooth driver should work under Win 10...

  But you have to watch for the manufacturer of modules... There are different modules like Atheros, Intel or Realtek

• Satellite C670 problems start after upgrade of Windows 10

  Hi all

  I made an upgrade of Windows 10 but after that my notebank satellite C670 has problems starting. It is always after the Windows updates were installed. It displays the logo of Win, followed of a blue screen. After several ignitions and extinctions I can once again the password login screen. Have already reinstalled Windows 10 because I did not come to the login screen more. But the problems are still there with ignition and extinction attempts it works. But this isn't a solution. You have ideas - drivers for Win10 or bios? Thanks for help

  Hello, I have the problem of the grandmother after the installation of Windows 10 I have nothing white screen
  Impossible to do a spanking Granny restore F8 or F12 nothing to do
  If someone gives you the solution I'm interested
  Thank you, CDT

  
  Validation has been translated by Google Translator

• Problems with sleep and stopped after upgrade to Windows 10

  Hello

  So I'm going to sleep problems and stop once I have upgraded to Windows 10 laptop won't sleep or stop correctly. The screen turns off, but the power LED remains lit and fan as well. If I chose the sleep he wakes up little matter what I try, and I have to make a hard stop at every time.

  Any solution to this problem?

  Thank you.

  1. Download version 9 or 10 of the Intel Management Engine Interface (MEI) driver.
  • Navigate to HP Software and Driver Downloads site (http://www8.hp.com/us/en/drivers.html) to find the last pilot approved for your model.  Filtrer filter by version, select Microsoft Windows 8.1 on the menu drop-down.  Find the download in the category 'Driver-Chipset'  If a pilot of MEI with a version from 9 or 10 number is listed, download.  [9.5.24.1790 version 1.5 M (http://ftp.hp.com/pub/softpaq/sp66001-66500/sp66228.exe) works for most models.]
  • If a pilot of MEI with a version from 9 or 10 number is NOT listed, download the driver appropriate directly from Intel (https://downloadcenter.intel.com/search?keyword=intel+management+engine).  [9.5.24.1790 version 1.5 M (https://downloadcenter.intel.com/download/23091/Intel-ME-9-Management-Engine-Driver-for-Intel-NUC) works for most models.]
  2. Download the Package of troubleshooting Windows 10 "show or hide updates" (http://download.microsoft.com/download/F/2/2/F22D5FDB-59CD-4275-8C95-1BE17BF70B21/wushowhide.diagcab).
  3. Change the Windows Update Services automatic (delayed start) parameter to the manual.
  • In Control Panel, select administrative tools, and open Services.
  • Go to Windows Update and double-click it to view its properties.
  • Click on stop to stop the service to run.
  • Change the Startup Type to manual, and then click OK.
  4. Install version 9 or 10 of the Intel Management Engine Interface (MEI) driver.  If you receive a warning dialog box about the replacement of a newer version of the software, accept it.
  • NOTE: You have NO need to uninstall version 11 before installing version 9 or 10.  The presence of a version of the driver is required to 'upgrade' (or demote in this case).
  5. Run the Windows 10 Troubleshooting Package 'Show or hide updates' and hide the updates of the Intel Management Engine Interface (MEI) driver.  (This will block your system automatically reinstall or display of updates for version 11 of the pilot).
  6. Change back the setting of Windows Update Services to manual automatic (delayed start).
  7. Restart your computer.
  8. Rejoice!  You can finally sleep and stop again.

  -DanG

• Satellite L40t-b917 - sleep problem after upgrade to Windows 10

  Name: satellite product L40t-b917

  Operating system: Windows 10 (64-bit)

  Hello

  If I have problems with the mode 'sleep' after that I upgraded to Windows 10. When I try to resume my laptop from sleep mode, Toshiba screen seems then the unit turns off.

  After 2 hours of searching on the internet I found that a solution said that my drivers are too old. So I tried to download but my drivers resembles not yet supported.

  Any solution to this problem?

  Where can I download updates for my device?

  Thank you.

  Hello

  Go to control panel and uninstall the Touchpad, display, wireless and sound drivers/utilities.

  Restart, and then run Windows Update to install the updated Windows 10 compatible drivers.

  Make sure that the BIOS is also the latest version.

• Problem Bluetooth satellite P70-B-102 - upgrade to Windows 10

  Hello to all forum users.

  I have a laptop Toshiba Satellite P70-B-102 with the operating system Windows 8.1 in Portuguese.

  The problem I have is that I can not upgrade to Windows 10, since, according to the upgrade of Windows application, the computer cannot update the Bluetooth drivers, including the following: Bluetooth RFHID, RFBNEP, RFBUS and RFCOMM.

  This situation remains at least a month and a half and I can't update windows to version 10.

  Can someone help me solve this problem?

  Thanks for your valuable help!
  Pedro Moura

  It's very strange... I think it must be some kind of Windows bug... I recommend you check if all Windows updates and patches are installed.

  In addition, the unit is listed as a supported upgrade Win 10 model, so win 10 update should be possible.

  The unit is here: http://win10upgrade.toshiba.com/swup...spx?region=TEG

  Win 10 driver can be downloaded and updated from this page:
  http://win10upgrade.Toshiba.com/swup...SPX?region=TEG

  but in case the upgrade of Windows 10 using the automatic upgrade procedure does not work, try to improve Windows 10 using the media creation tool
  http://Windows.Microsoft.com/en-us/w...n-tool-install

• Problem with the touchpad after upgrade to Windows Vista

  After that I've upgraded to windows vista I had problem with the touchpad, that I'm not?

  Can U help me!

  Maybe when you tell us what model of laptop you have. ;)

• DesignJet 111: DesignJet 111 - printing problems - no printing after upgrading to Windows 10

  Several problems to the upgrade of WINDOWS 7 for WIN 10.

  The HP DesignJet is 'offline' and can't figure out how to change the setting of "online."

  The definition "print directly to the printer" is not.

  Yellow flashing on the printer dashboard - magenta ink cartridge shows empty, but it is full.

  Computer HP printer installed - poster is in the Device Manager - watch "this device is functioning."

  Printer is listed in devices and printers.

  HP Support Assistant doesn't recognize - printer in the list, can not find device during an attempt of "add design.

  Printer turns off or recycle off on after turning on.

  Hello

  If you have a driver problem:

  Remove the driver completely from the computer, then download and install the lates driver.

  Here is the link incase you need

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=4123145 & swLangOid = 8 & swEnvOid = 4192

  Now, the yellow light flashes on the Panel means that the printer needs attention, like:

  -Close coverage which is open

  -Of paper

  -Paper tilt

  -Jam

  -An error code

  If you have 6 columns on the levels of ink instead of 4 is because you have an error code.

  On the following link, you can find more information on how to prepare the error codes

  http://h20565.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=352387 & docid = emr_na-bpp03841

  If you have an error code, the printer appears offline on your computer.

  On this other link, you will find how to check other messages on the printer

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01669949

• Solution for Webcam sleep & back problems after the upgrade to Windows 7

  Just thought I'd share the solution I recently found a problem I've had since a Satellite Pro A200 GE 26 Q of the upgrade from Vista to Windows 7.

  I installed the software webcam for windows 7 on the toshiba site and built-in Chicony camera would work very well after a reboot, but if the computer is in sleep for a long enough period, the unit would stay asleep when the computer woke up and wouldn't work at all, unless the computer has fully restarted.

  The solution lies in a change in the registry to force the computer to update the webcam USB controller is attached, after the release of sleep. It was apparently the default for Vista when it was released, but was changed in Vista SP1 and Windows 7. Designed for Vista original material which did not have its drivers/registry updated entries could therefore be subject to a failure because of changes to the default settings through the updates of windows. Toshiba, it seems, do not think that this issue then of the extinction of the registry fix for Win7 upgrades for the satellite Pro A200. Therefore fix manually.

  The article where the solution is here: [http://support.microsoft.com/kb/928631]

  You do NOT have the file of the fix, you must only make the change to the registry described later.

  You need turn on the camera while you do the following to make sure that it appears in Device Manager correctly.

  Step 1: Determine the specific USB host controller

  
  # Click on * early *, enter devmgmt.msc #the * search * box, then click on * devmgmt.msc* in the * list of programs.
  # The * view * menu, click on * devices of * connection *.
  # Expand the processor node. For example, expand * ACPI * Multiprocessor PC *. (In my case, * ACPI x 86 based PC) *.
  # Extend * system compatible ACPI Microsoft *.
  # Extend * PCI Bus *. Several USB host controllers will be listed.
  # Expand each USB host controller node, and then expand successive subnodes until you find the name of the device that is failing. For example, the device entry might look like the following: ACPI Multiprocessor PC\Microsoft ACPI-Compliant System\PCI Bus\Intel (R) \ICH8 family USB Universal Host Controller - drive root Hub\fingerprint 2830\USB * (Note: for me, I found the webcam to ACPI x 86 PC\Microsoft ACPI-Compliant System\PCI Bus\Intel (R) \ICH8 family USB2 Enhanced Host Controller - 283A\USB Root Hub + USB Composite Device\Chicony USB 2.0 Camera-based) *.
  # When you have located the device, right click on the associated and then USB host controller click on * properties *. In the example that is listed in step 6 you would right-click * Intel(r) ICH8 Family USB Universal Host Controller-* 2830, then click on * properties *. (* Again, for me it was different - ICH8 Family USB2 Enhanced Host Controller - 283 a *).
  # Click on the * details * tab.
  # Select * pilot key * in the list. The driver key will look like the following. Note the last four digits of this driver key. {36fc9e60-c465-11cf-8056-444553540000} \0002 * (on my system it's: (36fc9e60-c465-11cf-8056-444553540000) \0005*).
  
  
  

  Step 2: Add the ForceHCResetOnResume registry value for the USB host controller

  
  # Click on * early *, type regedit #in the * search * box, then click on * regedit.exe* in the * list of programs.
  # Find and then click the registry subkeys that are similar to the following: * HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contr ol\Class{36FC9E60-C465-11CF-8056-444553540000}\Four-digit_number.* in this step, the numero_a_quatre_chiffres is a placeholder for the USB devices in the system.
  # You must search the registry subkey by using the value that you noted in step 9 above. For example, if the key of the pilot to step 9 is * {36fc9e60-c465-11cf-8056-444553540000} \0002*, then you need to get * HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contr ol\Class {36FC9E60-C465-11CF-8056-444553540000} \0002. (For me, as mentioned above, this was \0005 (36fc9e60-c465-11cf-8056-444553540000)). *
  # On the * Edit * menu, point on * New * and then click on * DWORD value *.
  # Type# * ForceHCResetOnResume * to the name of the DWORD and then press ENTER.
  # Right click * ForceHCResetOnResume * and then click on * edit *.
  # In the * boite box the value data, type# 1 and then click on * OK *.
  # Exit the registry editor.
  # Restart the computer.

  This fixed the problem for a long time for me. I'm writing this in case it helps someone else who has the same problem. If anyone from Toshiba never reads this, you might consider adding the registry fixes for upgrades of windows 7 on the download page for this & all other models affected.

  Big Hey what s announced and detailed, thank you! :)
  I m wondering how you discovered it.

  But I want to add something: before you make or change something in the Windows registry, make a backup of it. In the worst cases, restore you the old Windows registry. Just to be sure ;)

• Problem to upgrade to windows 7 (Satellite L350 21J)

  Hello

  I have a problem complicated (for me): I had Vista on my 350 satellite and one of my friends put mac os x on it, it worked well, but usb and dvd player wasn't working.
  So I decided to buy the upgrade to windows 7 I have now on 2 DVDs. I don't know how to do this.
  When I put the update Toshiba DVD in the drive it does not, start my laptop to accompany still on mac os x.

  Can someone help me?

  If you have purchased the upgrade kit Toshiba, it can be upgraded from Vista to Win7.
  The first step is to install Vista using Toshiba recovery image.

  At this point an important issue: you have created disk facilities DVD using "Toshiba Recovery Disc Creator"?

• Satellite A200 - upgrade to Windows 7 - DVD Player problems weird!

  Hello

  I decided to upgrade to Windows 7 rather than replace my A200, which is always good as new after 3 1/2 years...

  In typical MS fashion, the upgrade was not incident free, but the main problem is that my DVD drive will no longer read my 2007 Microsoft Office installation disc.

  I CAN read the disc I've burned before the upgrade (with files/photos matching on etc.)

  Someone at - it ideas? Tried to update the driver and by stopping the service Detection hardware kernel (such as recommended on a forum of MS), but no luck

  Thanks in advance!

  > main problem is that my DVD drive will no longer read my 2007 Microsoft Office installation disc.
  A friend of mine had the same problem with the disc of MS Office.
  It was not possible to read this disc, but other drives were compatible.
  He cleaned the drive laser lens with a hint of alcohol and cotton wool, and it helped.

  Check it!

• GeForce 9800GT problems (resolution and horizontal lines) after upgrading to Windows 7

  I have recently upgraded to Windows 7 on my desktop HP m9350f computer.  I more a few days later my screen has finished by resolution 800 x 600 with horizontal lines on the screen, from the start.  I spent several hours with the support of Microsoft and HP by train to reload the updated drivers from the Internet HP site and Web of NVIDIA site with no improvement.  As part of the normal troubleshooting I plugged a cable and another monitor and the problem is neither the monitor nor the cable.  I removed the video card and temporarily replaced by another video card and the problem goes away, so the problem is with the graphics card (as opposed to the motherboard).  I replaced the NVIDIA card and the problem is back, essentially confirming that the problem is directly related to the graphics card.  While I found 'a lot' of discussions on the internet about similar issues with 9800GT cards, I can't find a solution to this problem. HP and MS have exhausted their resources. Any ideas or solutions?

  It's time for a new video card.   Remember to match the energy needs of the new card with the power supply of your PC.

• Problem with a keyboard key of T440 after the upgrade to Windows 10

  Hello world

  I have a Brazilian keyboard layout (ABNT2) on my T440 and I am facing a problem after the upgrade to Windows 10. The new version of Windows recognizes this key:

  

  As long as the "CTRL on the right" (commom on other layouts).

  Everyone was faced with a similar problem or have any clues as to what might solve this problem?

  Thanks in advance,

  Felipe

  Solved.

  Do more research, I fount out is an old bug with Lenovo's Thinkpad laptops with this Brazilian keyboard.

  If you are facing the same problem, use this registry tweak and the problem is solved:

  http://ZTop.com.br/WP-content/uploads/2009/11/thinkpad_abnt_win7.zip

  (the file name indicates "win7" but it also works for Windows 10)

• WiFi problem after upgrade to Windows 10

  Greetings!

  I read a few posts on WiFi problems after the (improper) upgrade of Windows 10. I have a ThnkPad T530 which I've upgraded to Windows 10 Windows 7 in September (too late to roll back). Here's my question:

  I have three computers on my desk. This standard T530 running Windows 10, a ThnkPad E555 running Windows 7 and a Dell running Windows 8. I used all three last Friday. I installed Norton on all three Friday and everything went without a hitch. When I first started their return to the top of this morning, the two others came online as usual. The ThinkPad T530 connected by a router in the company, but has no access to the internet. I can connect to the hotspot on my phone and it connects fine. I tried to turn the WiFi connection and then turn it on again, restart, by killing and restarting the business connection, etc. Nothing changes.

  Help, please

  Ben

  Try the following:

  Open administrator command prompt:
  http://winaero.com/blog/how-to-open-elevated-command-prompt-in-Windows-10/

  Then, run this command:
  netsh int ip reset c:\resetlog.txt