8024F Port Mirroring not capture all traffic

Similar Questions

• WRVS4400N will not route all traffic on IPsec

  All my remote sites use various routers to route all their traffic via IPsec.  However, I have a WRVS4400N w/firmware configured 2.0.2.1 with a tunnel of work.  My problem is that I need to define the Group of remote 0.0.0.0 0.0.0.0 so all traffic is forced through the IPsec tunnel and not on the local gateway.  When I make the mistake, Remote Security Group and Local security group cannot be in the same network. However, it works with Cisco/Linksys RV042.

  Any ideas?  Attached are the screenshots of each.

  Transmission of wildcard ESP isn't a feature support, therefore not documented in the product documentation. If you need a wifi router that supports this feature, you can see the series Cisco ISR, which is base IOS.

• USB ports do not work all of a sudden and I can't back up or sync

  When I connect a device (for example, BlackBerry or external hard drive), the USB ports all of sudden does not recognize these devices.  Worked fine one day and then stopped working the next day.  I tried several times to address the problem by uninstalling the USB drives and reboot.  This worked only once.  Then, the problem is back.  I am frustrated and at a loss.  Any help out there?  Thank you.

  Hi Lee,.

  1. you remember to make changes to the computer before this problem?

  2. you receive messages or error codes?

  You can try to start the Fixit for USB devices and check.

  Check out the link:

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Distribution list do not capture all members?

  Hello

  I recently created a distribution list.  I add contact groups and that I was adding them I noticed the number of members in each group.  My score was 27 k, but after recording and refreshing said Eloqua had only 12 members of k in the distribution list.  Excluded members totaled only to 2467.

  Anyone know where the other 12 k is gone?

  Thank you

  1. Looks like it works very well... at the moment you start with a list of names 12 795 in your contact group. Now if that's from the 27 K you mentioned before, where is the problem. It could be fooled through 10 contact groups you use, but the mailing list works well... you had 12 795, then lost 2 467 at the system level excludes and cancels his subscription for a total of 10, 328... so the lsit distribution works really well. the question seems to be in your contact groups. Looks like you have 10 groups put in place that creates the final 12, 795... could there be overlap between here in these 10 groups? They automatically deduplication outside when you combine them in unity of contact groups in the group... If that makes sense. For example, if I put two groups on my side, one for 156K and one of the 63 k. general might think I wish 219K, but after deduping, it shows 195K, so 24K have been fooled. What appears on the distribution list is the 195K... it will show as a member of the contact group, then 2 (for both lists, I combined) and the number of 195 K (deduped)... hope that makes sense and helps

• vDS Port Mirroring

  I am mirroring traffic of the virtual machine on a VDS.  It is mirrored traffic to physical server somewhere else in the data center.  As always, I also have a vmkernel port used for ESXi management traffic. When I create a Port of vDS session - that the interface of mirroring is the traffic opposite Let ESXi on?  The vmkernel port or virtual switch still port management ESXi virtual machine is on?  Port mirroring sessions send all data on the management port vmkernel at all?

  This means that the traffic in the opposite direction will leave the ESXi management vmkernel port?

  This seems to be the case and is the only way that seems logical. I mean that you have need of a few independent existing IP stack to carry the encapsulated traffic.

  It is also suggested by this article:

  http://www.routereflector.com/2014/07/port-mirroring-on-VMware-vswitchdvswitch-dvmirror/

• One of my usb ports does not work. A top forward on a MacPro 3.1

  So I plugged it in a charger to charge a battery. He went for about 1/2 hour then I got a message a lot of power, port and it will stop the port. Something like that. So now the port does not at all with any device. Can this be reset?

  Running OS 10.6.8 snow leopard. 3.1 MacPro Tower.

  Try a reset of the MSC...

  MacIntel: Reset of the controller (SMC) system management

• 6248 - port Mirroring

  We want to control our 6248 laptop Win 7 help with Wireshark

  We need to display all the packets on all the VLANS

  Question:

  For mirroring destination port must be on the VLAN 1, trunk or can we only monitory / mirror on the base of each vlan?

  Thanks in advance for your help,

  Hello

  Port mirroring will keep all tags VLAN as they were on the original port. Page 332 ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/powerconnect-6248_User%27s%20Guide2_en-us.pdf

  It should be able to reflect several VLANS.

• HP ENVY Beats all-in-One: usb 3.0 ports do not work

  USB 2.0 hubs work but the 3.0 have never worked. Thumb drives and exterrnal readers do not appear in the file manager. No problem, indicated in the Device Manager.

  Thank you for your help.

  After searching around, I found new info: F2 at startup - BIOS - HP has a tool to check if different parts of the computer are working correctly. (Officially), I learned that the usb ports two 3.0 do not work (despite Device Manager, telling all the devices work properly). I received a "failure code" and a phone number to call. Technical support has confirmed that the failure code indicated the 3.0 ports do not work, and for $215 they can repair (price including shipping Fedex).

  I see if someone locally replace ports. Not sure that 3.0 ports are worth anywhere from $215. After all, the computer works just fine as it is. It's just annoying, they have never worked, that it took so long to finally find a solution, and that the warranty has expired.

• Port forwarding in vmware workstation 9 (how to transfer all traffic to a virtual machine)

  You are looking for here: Advanced Configuration of NAT

  I can see how to redirect ports via in a particular host vmware NAT service, but my question is how can I transfer ALL traffic to a host? I found no info on how to do that.

  Is there any way I can forward all traffic incoming on a virtual machine?

  The syntax is = : and as such it is singular in all references, so I don't know of a way around it.

• Photosmart C4280 All In One: USB Port does not work

  When I try to scan, I get a message saying that the USB port is not installed. It is installed, but I bought a new USB port and still get the same message.

  Hi @MrsQ3,

  Thanks for getting back to me with this information.

  Have you already tried to install the software and drivers from hp.com printer? If you do not try to download the HP printer installation wizard for installation. This tool will find the most recent version of the printer software and drivers available for Windows 10.

  If you have already installed the printer software, try downloading and does not perform the HP print and Scan Doctor. This tool can diagnose and solve many problems of printing software and printer.

  Please let me know how it goes.

  Thank you.

• Not all traffic tunneling remote desktop

  This is the remote router config 871 attached. Comes in the SAA under DefaultL2Lgroup. Another remote desktop is the same tunnelgroup. Traffic to 192.168.0.0/24 works, but I also need the tunnel to all traffic 10.8.0.0/24. Let me know what you think. Thank you

  Right, the problem might be on the router.

  Try turning off the "no ip cef" CEF and check again.

  Please rate if this helped.

  Kind regards

  Daniel

• Why cfstat still poster reqs qued even when it is not all traffic to the site?

  I try to use cfstat to help understand some performance issues with our production server. Its CF 10 Ent on a Windows 2008 VM. I'm also 10 ColdFusion installed on a local Windows VM.

  I run cfstat with a 1 Refresh second on the local production and the VM server. The local VM Reqs Q column ' ed shows a constant 10 even if I'm not hitting all sites on the server. The production server shows a constant 20-Reqs Q'ed and some Run Reqs'g.

  Is this normal? I have to make some adjustments to the CF or the JVM?

  Thank you

  Hi Phil,

  CF10 CFSTAT seems not to be as convenient as CF9 or earlier version.

  Requests queued seems to be displaying the value of tomcat for minSpareThreads connector. Tomcat minSpareThreads is the minimum number of threads still kept running. If not specified, the default value of 10 is used.

  HTH, Carl.

• VM adds a Port Mirroring Session

  I need each VM added to a file given in the vCenter to be added to an existing distributed switch port mirroring session.  Is this possible with PowerCLI?

  The following will add the virtual machine ($vmName) to a port specific, mirror of the session ($mirrorSessionName) on a distributed switch ($dvSwName).

  You can define the directions of traffic for which the virtual machine must be added with the $Ingress and $Egress variables.

  Note that it is not an error checking in the script.

  For example if the mirror session does not exist, the script fails without information messages.

  Yet once this script for all the virtual machines in a specific folder should not be too difficult, I guess?

  $dvSwName = "dvSw1".

  $mirrorSessionName = 'test '.

  $vmName = "VM2.

  $Ingress = $false

  $Egress = $true

  $dvSw = get-VDSwitch-name $dvSwName

  $vm = get-VM-name $vmName

  $vmNic = $vm. ExtensionData.Config.Hardware.Device |

  where {$_.} Backup - is [VMware.Vim.VirtualEthernetCardDistributedVirtualPortBackingInfo]}

  $spec = new-Object VMware.Vim.VMwareDVSConfigSpec

  {foreach ($mirrorSession to $dvSw.ExtensionData.Config.VspanSession)}

  If ($mirrorSession.Name - eq $mirrorSessionName) {}

  $vspan = new-Object VMware.Vim.VMwareDVSVspanConfigSpec

  $vspan. Operation = [VMware.Vim.ConfigSpecOperation]: edit

  $vmInRc = $mirrorSession.SourcePortReceived | where {$_.} {Portkey-contains $vmNic.Backing.Port.PortKey}

  If ($Ingress - and! $vmInRc) {}

  $mirrorSession.SourcePortReceived.PortKey += $vmNic.Backing.Port.PortKey

  }

  $vmInTx = $mirrorSession.SourcePortTRansmitted | where {$_.} {Portkey-contains $vmNic.Backing.Port.PortKey}

  If ($Egress - and! $vmInTx) {}

  $mirrorSession.SourcePortTransmitted.PortKey += $vmNic.Backing.Port.PortKey

  }

  $vspan.vspanSession = $mirrorSession

  $spec.vspanConfigSpec += $vspan

  }

  }

  $spec. ConfigVersion = $dvSw.ExtensionData.Config.ConfigVersion

  $dvSw.ExtensionData.ReconfigureDvs ($spec)

• Distributed Port Mirroring on hosts in same vDS

  Hello:

  I have two hosts (esx01 and esx02) 5.5 ESXi running connected to the same vDS 5.1.  I have no problem passing traffic between virtual machines that are on different hosts and in the same port group, so I know the vDS does what it is supposed to.  Each host has 8 vmnic and vDS 8 links rising, all set to active.

  However, when I install a port mirroring distributed on the vDS and choose a source port and the destination port, I get only the traffic on port of destination if the ports are on the same host.  If the source and destination are on different hosts, no mirror traffic is received.

  Sort of, I worked around it by using the following https://everythingshouldbevirtual.com/vmware-vds-rspan-port-mirroring, however, that ends up giving me lots of duplicated packets when I attach to a single connection (probably the switch is to see the input/output traffic on the two vmnic of in the binding rising vDS?)  For each package, I see 8 duplicates.

  But it seems to me that it should "work" without having to do anything to miss.  I also tried to look: vSphere 5.1 - VDS - Port Mirroring feature enhancements - part 3 | VMware vSphere Blog - Articles VMware., but with that it seems that are filled with separate vDS, which in this case an RSPAN makes sense to switch to pass traffic.  But in my case, it's a simple switch that is sitting between two hosts connected to the same vDS.

  Thoughts or directions to guide me to the answer would be greatly appreciated!

  
  Josh

  Hello jmapt,

  Please note the following:

  Page 152:

  Distributed Port Mirroring:  Mirror of packages of a certain number of ports distributed to other ports on the same host. If the source and destination are on different hosts, this type of session does not work.

  And:

  vMotion compatibility:

  Port mirroring between ports distributed may be local. If the source and destination are on different hosts as a result of vMotion, mirroring between them will not work. However, if the source and destination are moving to the same host, port mirroring works.

  http://pubs.VMware.com/vSphere-55/topic/com.VMware.ICbase/PDF/vSphere-ESXi-vCenter-Server-551-Networking-Guide.PDF

  Good vDS seems to essentially be a single switch is not. The control plan is unique and is driven by vCenter but the real data plan in at the host level, and each host has its own data plan for the vDS. So the underlying terms of data are they different switch running on different hosts.

• Port Mirroring mit SRW2016

  Liebe Foren-user,

  ICH möchte like einen Port Switch SRW2016 "monitors" (second later mirror-Port). Dazu habe ich einen Rechner mit und tcpdump aufgesetzt, diesen a debian Port einen angeschlossen (den probe-Port). As soon as ich über das Web Interface Linksys-switches switch unter meines-> Port Mirroring den mirror-Port auf den spiegeln tired (both Directions) Port probe, ist tot practical der probe-Port. ICH kann vom Debian-Rechner aus nichts mehr pingen (auch nicht den Linksys Switch), er kriegt keinen release DCHP mehr und er ist auch nicht mehr aus dem Netzwerk reached normal. Konnte damit ich ja notfalls leben, however scheint überhaupt kein mehr auf dem probe-Port anzukommen traffic. Tcpdump shows mir keinen traffic one.

  Mache ich irgendwas please? Sind die Einstellmoglichkeiten zum Port-Mirroring am State ja, ich SOMIT fits Linksys, actually nicht viel outlined machen zu können. Equivalent Passagen im hab ich naturally read manual.

  Vielen Dank und Grüße

  Tobel

  Von your description wird nicht klar, wie das MIrroring exakt adjusted did.

  Der 'Source' Port is the Port the system want to play, wo der d.h. den "Original"-Verkehr drüber geht. "."

  Der 'Target' Port is the Port, auf die in den packages kopiert werden, d.h. sleeps schliesst tcpdump mit den of the computer one.

  Buyed is, dass die Netzwerkkarte am target Port both adjusted ist, dass sie alle frames akzeptiert. Frames usually werden ja alle, die nicht die loading MAC address verworfen haben.

  Also hat computer der über den Port target keine connection. Target akzeptiert keine der-Port frames. ER sendet nur die copies of the Source Ports. Das ist eine der SRWs Beschrankung banknotes.