8500 a does not print after mode 'sleep'

Similar Questions

• OfficeJet HP 6830: officejet hp 6830 does not respont in mode 'sleep' via an ethernet connection

  HP officejet 6830 does not respont in mode 'sleep' via an ethernet connection.

  This isn't the case via a usb connection.

  What can I do?

  Hey @George5500,

  Welcome to the HP Forums!

  I understand your JO 6830 unresponsive when it is in standby when you are using the Ethernet connection, but it does not occur when connected via USB.

  We will perform a hard reset. To do this, leave the printer and unplug the power cable for 1 minute. While it is unplugged, press and hold the power button on the printer for 10-15 seconds to release built his power, then after the minute, plug the printer in. Also, even if you have used a surge protector/power bar this whole time and you feel this isn't the cause, please plug it in to a wall outlet so that we can eliminate the source of energy as the primary cause.   Questions when it is connected to an uninterruptible power supply/Strip/surge protector power

  * In this document, you will see, QUESTION: questions or problems may occur when a printer HP LaserJet series printer is connected to a UPS (UPS), a power strip or a surge protector that is not limited to the Laserjet printers.

  I can't wait to hear back on your part. If performing a hard reset, or move the printer to a socket solves the problem, please click Accept as Solution button below so that the community can see your problem is solved. If the problem persists, please don't forget to leave me and I'll do everything I can to help.

• Qosmio X 300 - 11W - TouchPad does not work in mode 'sleep'

  TouchPad does not work in mode 'sleep'. I can't wake up my computer using a touchpad. I downloaded and installed a driver for Windows 7 32 bit from a page of the Synaptics driver, but it did not help.

  Can you wake up your Qosmio using the power button / stop?
  You close the lid when the laptop enters the sliding mode?
  After you open the laptop lid should wake up. It work correctly?

• Printer does not print after canceling a print job even if I deleted the queue and stop the printer and the computer.

  Re Vista - printer does not print after canceling a print job even if I deleted the queue and stop the computer and the printer and restarted.

  Hello

  ·                         try to uninstall and reinstall and use the latest printer drivers VISTA for your model of the manufacturer of the printer

  You can also track information to try to solve your problems of printer below

  read the printer correct that information the slot microsoft, including the 'fix - it' and the information of the links to the other

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  and read this microsoft tutorial too

  Introduction

  This tutorial is designed to help you identify and fix the problem printer common windows problems, including print errors, or errors, and other issues that could prevent you from printing. This tutorial does not cover printing problems related to specific programs. Printing problems can be caused by cables that are not properly connected, corrupt, drivers, incompatible drivers, the printer settings, missing updates and problems with your printer.

  How to use this tutorial

  For best results, complete each step before move you on to the next. Try to print after each step before moving on to the next step.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• Epson Aculaser C 1100 printer does not print after that the text of the error 'install C Tnr basket' black and printer doenst photography black and white or grayscale pages

  Epson Aculaser C 1100 printer does not print after that the text of the error 'install C Tnr basket' black and printer doenst photography black and white or grayscale pages

  the printer is not the shades of grey even print cartridge is not yet empty

  y at - it software for hauler color printing?

  Thanks for your comments

  Hello Nilsvolkel,

  Thanks for the reply.

  I'm sorry for the late reply.

  I appreciate your patience and time.

  Do not require any special software.

  However, you can use the steps in the following articles and check.
  Reference:
  http://eSupport.Epson-Europe.com/ViewArticle.aspx?LNG=fi-fi&kbid=328037&data=FCFfEfoyEiGLYDIUqzWyE0QE3127X87y&CL=1

  http://Windows.Microsoft.com/en-us/Windows/choosing-print-options#1TC=Windows-7

  Please keep us informed.

  Thank you

• HP LJ MFP M425dw 400 does not wake after entering sleep / Auto mode

  Hello

  After you have installed the latest version of the firmware 20140521 (May 21, 2014), the device is not trampled after entering sleep / Auto Off mode.

  The configuration of the device and save the settings listed below.

  Tell me how to solve this problem?

  

  

  It could be a hardware or a firmware related issue.

  You try to perform a reset of the base unit and also try to send new firmware.

  The device may need to be tested with additional troubleshooting steps, so I would say to make an appeal for support through your regional HP Support channel.

• HP Envy 7645: HP Envy 7645 does not print after installation (Windows 8 64-bit)

  I have a weird problem with the HP Envy 7645. After going through the movements to print anything, documents word to pages web, the printer does not print the document and somehow work not even end in the windows print queue. I ran all the diagnosis of HP and there is no connectivity problem, be it wireless or USB connected. No one else in my family have printing problems (we use XP, use another 8.1 and a mac user). The printer prints a test page and a page of diagnosis of the HP software, but will fail to print a windows test page 8. Also the windows 8 printer troubleshooting tool detects any problems with the printer. I'm a bit of a loss.

  I saw a similar question on these cards with the HP Envy 5530 and wonder if it should be the same solution. However, after watching this Board, it requires the name change of a different .dll extension that I don't see with the 7645, but I was wondering if it could be something similar. Has anyone else encountered this problem?

  UPDATE: I solved the problem yesterday, but not by the above method, I had tried earlier. I tried a solution for the 5530 envy and it worked. I completed all the steps, including get adobe flash. Only, I have encountered a problem and has been updated to adobe flash. It would download, but as soon as it starts to install, I get a message: "this user has not sufficiently privleges." If you get this error, I'll post the links I used to solve the problem below the solution. I do not guarantee they will work, but they did for me. If not, just follow the step by step solution below:

  EDIT: I forgot to mention that, before using the links to solve the problem of permission with adobe, I had created another account to administrator in Windows 8 and activate the default Administrator account, which is hidden. None of these solutions had solved the problem, but you can try these first, despite the fact that the difficulty of a temp.

  ___________________________________________________________________________________________________

  Sunshyn2005

• my printer does not print after a new router, I configured it but still does not

  I have a new router and configured it for my printer a Kodak ESP5250, I did all the things the computer told me to to try to resolve the problem, restart spooler ect, but it still won't print and I'm on my work please help. Thank you

  Thank you very much for your help, I was told by a friend to the support ring at Kodak who I did it remotely, they got into my computer and solved the problem, still not sure it was good. I was impressed by the response here and it was fixed in five minutes. So if anyone has a Kodak printer that does not print from the computer, but the impressions of the printer, this is the road to go down. Thanks again for your help.

• OFFICEJET J4680 ALL IN ONE PRINTER does not print after installing Windows 7

  THIS HAPPENED MORE THAN A MONTH. I STARTED WITH WINDOWS VISTA. HP SUPPORT ADVISED LATER FOR THIS WINDOWS 7 WORKS BETTER FOR MY PRINTER. NOW I HAVE INSTALLED WINDOW 7 AND I GOT THE PHONE SUPPORT TO GO ON MY COMPUTER AND SET IT UP. EVERYTHING WORKED AS SUPPOSED, PRINTING, SCANNING. THE NEXT DAY I TRIED TO PRINT SOMETHING AND I WENT BACK TO SQUARE ONE. The SCREEN LIITLE ON THE PRINT JOB CAME AND SAID THAT the PRINTER does NOT PRINT. I WENT TO THE HP SOLUTION CENTER AND A NOTE SAID THAT THE PRINTER IS DISCONNECTED. I RETURNED AND COPIED MY NETWORK CONFIG. AND THE WIRELESS TEST. EVERYTHING IS RUNNING WELL HUNG OF THE PRINTER. THE DEFAULT PRINTER IN THE RIGHT IMAGE. THE ONLY THING I NOTICED WAS IN THE PORT AREA. UNDER THE WINDOW VISTA, I GOT TWO PORTS. ONE WAS FOR THE PRINTER AND OTHER FAX. WHEN THE HP PRINTER HAS BEEN REINSTALLED, I DON'T KNOW IF IT STARTED WITH ONLY ONE PORT. THE PORT IS ENABLED BY IT AND HAS THE FAX FROM WORD TO THE END ON WINDOWS VISTA, BOTH PORTS HAVE THE SAME INFORMATION, EXCEPT A EU FAX OF WORD AT THE END ANY HELP ON WHAT SE PAST.

  I JUST INSTALL WINDOW 7, MY OFFICEJET J4680 ALL IN ONE PRINTER. NOW IT WON'T PRINT. THE DAY BEFORE, IT WORKED.

  Hey 123 problems,.

  You will need to go to the HP website to download the latest software/drivers for your printer on Windows 7:

  http://h10025.www1.HP.com/ewfrf/wc/product?product=3692888&LC=en&cc=us&DLC=en&lang=en&cc=us

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• HP Photosmart C309a does not print after I installed new black ink cartridge.

  Printer was working fine until I replaced the black ink cartridge.
  Does not print the text in black on the printer test page.
  The States new HP printer installed cartridge.
  All other colors are working well and were replaced at the same time.
  Tried cleaning cartridges - pulling the cartridge and put back in - turning the printer off and on again.
  Also tried to restart the computer.
  Could there be a problem with the ink cartridge itself?

  REAL SOLUTION. I had the same experience, spent hours pulling my hair like children had project do to school and it was 22:00.  Your cart is clogged! Here IS THE SOLUTION! (: 1) remove all ink cartridges. (2) extract the carriage that circulate in the ink cartridges by lever on the right and the trolley lifting vertically. (3) wipe any accumulation of visible ink on the outside with clean cloth or paper towel. (4) THIS IS THE KEY: keep transport under hot running water to empty all the handwritten entries in the irrigation channels that distribute ink. Keep rinsing in clear water i.e. no sign of ink. (5) trolley dry with clean cloth and blowing in areas, you can access in order to remove the remains of the water. (6) let transport air-dry overnight. (7) Re-install transport, then reinstall the ink cartridges. 8) ENJOY YOUR PRINTER. (9) I saw many entries on this topic dating back two years, without real solution offered. I am an automotive engineer in unemployment. If HP (or anyone else) would like to hire a smart worker, engineer in the Detroit area, please inform. Thank you!

• C5550 does not print after upgrade 10,5

  Good, Startin ' Slam beers now... Updated my Mac to leopard (10.5.8) desktop computer and my Photosmart C5550 does not print. I uninstalled and reinstalled the printer software and everything seems normal until I got to "print" a document. It seems to send the info to the printer, but nothing happens. When I look at "Series of HP Photosmart C5500" in the doc it activates and when I select the icon in the doc it says under "printing" status and above her beside the printer image says "connection inactive. This printer is connected to my Mac via USB and it will not print a test page when envoys of the computer, but it will print a test page for its own controls. I thought that this printer is compatible with 10.5... Am I wrong? In addition, my desktop widget recognizes the printer and even says the ink levels. Any suggestions?

  Thank you

  just turn off the printer for the first time since the re - install and it's new to print.

• C4480 does not print after upgrading Vista to Windows 7

  Hello

  I bought a C4480 & installed on my laptop running Vista.  I bought recently installed Windows 7, it & printer worked OK. 2 days ago HP sent the file: PS_AIO_03_C4400_NonNet_Full_Win_WW_130_140.exe, (1/1, 205.09 M)

  I downloaded & installed, now the printer does not print. It scans ok just will not be printed. Called HP & said it was Microsofts problem. told by Microsoft of $ 80 or reinstall my computer back to the factory default settings. Not knowing much about computers I'm not want to do. The computer tells me the spool of printer off & to start but when I open the printer spool is on. I hope you understand that this is my 1st post.

  There is a patch for this here.  Try it!

• ALL-IN-ONE PHOTOSMART HP 5510 WILL NOT PRINT AFTER GO 'SLEEP' MODE

  My printer model:

  HP PHOTOSMART ALL-IN-ONE 5510 B111A

  Problem:

  Printer goes into sleep mode. After 25-30 minutes breaks the connection between the PC and the printer wireless. Beacon wireless is the same fashionable "sleep" and I see that the printer is connected to my router and there is internet connection. HP Print and Scan doctor sees the printer, but I can't wake the printer unless I restart it.

  What I've tried so far:

  I tried all the solutions offered hp.com; Reinstall driver, updating the printer software, setting static IP on the printer, static DNS servers, using HP print and Scan doctor.

  I've seen people questioned on this issue before and there is no solution. I really need help from HP!

  After days of research, the problem was finally solved! I applied the following steps below. Some steps may be unnecessary, I didn't waste my time knowing who.

  1. find your PC's DNS servers by typing ipconfig/all in CMD.
  2. assign a static IP address outside your DHCP range. For my Linksys router him between 192.168.1.100 to 192.168.1.150. So I put my static IP address as 192.168.1.20.

  To do this, click the button on your printer wireless. This will show the IP address of your printer. This type of your browser. Go/network/network address. Choose manual IP and write 192.168.1.20

  3 now come to section of the manual DNS server, and then type your DNS servers, you found before.

  4. open your HP printer program that must be installed with your driver. Utilities hit and update the IP address. Update your address with your static IP address.

  5. now go to your router settings. Find the wireless settings and change your not automatic standard 20 MHz radio band.

  6. change your standard channel to 6.

  7 find the wireless security and replace your WPA-personal security mode.

  8 disable UPnP

  9. This is the part of the KEY. Change the renewal of your key to 36000 seconds. (10 hours)

  10 go to the Windows Advanced Firewall. Enable all the disabled printer and share, entrants and outbond rules.
  I believe that the most important parts are affecting a static IP address outside your DHCP-range and change the key renewal time. I hope this works for you too

• HP CM1415fnw does not print after awhile

  I have a HP CM1415 cold printer.

  • LAN cable (WiFi turned OFF)
  • IP fixed, located on the Panel of the printer
  • No. "sleep mode" (permanently on)

  After that the printer is turned on, it works fine. After 10 to 30 minutes, printing is NOT possible. Windows or Linux (on see the same machine the same problem). Either by IP or USB printing, makes no difference. No printing is possible.

  PING works, and I get a response, if the printer is alive.

  http://192.168.1.249 . in the browser gives the expiration time.

  Nothing works, until the printer is turned off and then on again.

  If this problem:

  • no associated BONE (not driver problem)
  • no LAN / USB related
  • not the power-related settings

  What can be the solution? Material?

  I got your message, and thanks for the information continues.  I'll check this thread again Monday to see if the problem has been resolved.  I hope that reset could mitigate the problem you encountered.

  Have a wonderful weekend,

  Jason

• DeskJet 1050 - J410a: HP Deskjet 1050 does not print after upgrade of Windows 10

  Dear forum,

  I recently upgraded my HP Windows OS 8.1 for Windows 10 desktop computer. My deskjet 1050 printer, which worked fine before the upgrade, does not properly more print after the upgrade.

  I used HP Print and Scan Doctor several times, indicating no any problems. I am able to scan documents, the question is limited to printing. I also deleted and reinstalled the drivers at least 2 times (and restarted all systems on a regular basis).

  • A "test print" works very well.
  • When I print a PDF from the edge, the printer creates output but not good quality.
  • When I print an office word document, pages came out empty.

  3 cases have a common behavior, whenever I get an error message. "Morning maken puts printer niet mogelijk. Duch is for "cannot connect to the printer.".

  Do you have any tips for me?

  With sincere friendships.

  Pieter

  HeyPieter_Belgium

  Welcome to the HP Forums, I'd love to help you with printing problems you encounter. Although I am not sure what is cause of the error of communication, or of poor quality, I suspect it has something to with the pilot and the recent upgrade. I suggest to uninstall the software, remove the Chuck from the properties of the server, and then put it back using the printer Installation Wizard. I will list the links and instructions below to help you in each of these steps.

  HP printers - uninstalling the software of the printer (Windows)

  Remove the driver from the print server properties:

  1. in the folder "devices and printers".

  2. choose "print server properties.

  • Win XP - with no printer selected, click 'File' then 'server properties '.
  • Windows Vista - with no printer selected, press 'Alt' and then click 'file' then 'server properties '.
  • Windows 7/8, 8.1 and 10 -select any printer in the "Devices and printers" folder and click on "Print server properties" above.

  3. click on the "Drivers" tab at the top of the window "properties of the print server.

  4. choose the printer that you want to uninstall, and then click 'remove '.

  5. choose "Remove driver only.

  6. the next screen will give a warning, letting you know that the removal of the driver package will remove it from the system. Click 'Yes' to say are you sure you want to do.

  If documents are stuck in the spooler to print, you see an error, cancel all documents waiting in the print queue or try restart the spooler to print, and then try to delete the driver from 'Print server properties' again. If she will not always remove the sachet, restart the computer and the printer should correct this error "in use" and allow the driver to be removed.

  • If him you continue to get an "in use" message followed the steps in the document here. The specified printer driver is currently in use

  Download and run the Installation Wizard for printer: www.HP.com/go/Tools 

  If this solves the problem, please indicate your post as solved by clicking on the accept button Solution below. If you need help, let me know!

  Thank you.