9188 chassis cannot self test

Similar Questions

• Error code 200020 after self-test when chassis turns off

  Hello

  This may seem absurd, but I accidentally ran a self-test to the MAX on one of the NI PXI boards (6533) in my chassis (NI 1042 q) when chassis power was off. He returned with an error code of 200020. The same thing has happened with three other NI PXI boards: 6723 6713 and 6221. I turned on the chassis and the same error code occurred. Then I restarted my computer, responsible for MAX, and no devices were found even more.

  I followed the steps here to reset MAX, as well as the devices were recognized again, all the self-tests have passed again.

  However, I am concerned as to why it happened. Why the error code keep occurring after that I turned on the chassis? Why MAX ceased to recognize my devices? Something is screwed up when I tried to connect with an off camera? In addition, what does error code 200020? I couldn't find documentation about it anywhere.

  Thank you

  Hey,.

  From your description, it seems that you disable the chassis when the PC is still on. This will cause certainly some problems with your PXI devices, because you're basically hot-swapping PXI devices in your system. This may have also messed up things in MAX, as you saw. You should always have your PXI chassis before your start your computer turned on and turned off after your computer has been shut down. This allows your BIOS correctly enumerate the PXI card, which should hopefully avoid these mistakes in the future.

• F4280 in cannot print a "self-test" page

  My HP Deskjet F4280 refuses to print anything. My computer is a HP G60 64 bit laptop. I can cue printing projects and what a transformation the printer starts flashing the led "CV". I went through each technique of "Troubleshooting" offered by HP, nothing helps. My F4280 don't even print a "Self-test" page in now the power button / stop and 'X' button simultaneously. It's a... mechanical software, or a combination. I'm PUZZLED !

  Hey GinaKay,

  Glad to hear this tip worked for you!  Main thing you have to watch is the bag leaking, but it looks like you had a lot of success.

  I'll keep this one in mind for the future.

• myDAQ new installation self-test fails 88705

  "' Problem: NEITHER myDAQ"myDAQ1"- Measurement & Automation Explorer-online devices and Interfaces-online OR myDAQ" myDAQ1 "-online self-test does not work. The error message is "the self-test. has failed. -88705 the specified device is missing... »

  My environment:

  8.1 Windows 64 bit running under Oracle VirtualBox Version 4.3.20 running Mac OS x on a MacBook Pro 2012 10.10.1. I have no prior exposure to work with myDAQ, LabView, or any tool of NOR.

  I downloaded NIELVIS1400_downloader.exe for Windows 8.1 to ni.com and it is finished.

  During installation I secured guarded against the problems of Win8FastStartup by stopping and restarting the PC when asked.

  After the installation when I plugged it physically in the myDAQ device, it was recognized by Windows 8.1 because Device Manager has the 'data acquisition' entries under which "NEITHER myDAQ" appears. For NEITHER myDAQ device status is 'this device is functioning.

  When the myDAQ was physically connected, the window "NI ELVISmx Instrument Launcher" popped up. I clicked on the icon 'How to set up your hardware' and the 'get started Guide... "pop up. I checked the blue LED on the device came and it is stable on. I went to "2. Paragraph confirms the recognition of the devices"in implementing on the way, guide and follow the instructions to start the automatic test. There not as described above.

  I noticed similar problems have been reported in the past. Closest to my problem reported by flex11 on 05/05/2014. Reading through I don't see any resolution itself. Another similar problem was solved by manually starting the service 'NOR device charger '. In my case, this service is already running. "NO license server" is the only service stopped, but I guess that's normal for myDAQ.

  I don't have any other product OR installed on the PC.

  I'm sure there is a simple solution to this problem, but I'm afraid it's escape. I'd appreciate any help I can get through this forum.

  Thanks for getting back to me. Your answer gave me stamina I had to move forward.

  I installed http://www.ni.com/download/ni-daqmx-14.2/5046/en/ and finally managed to do work. The exact boot sequence I need is:

  (1) delete myDAQ by USB port and then start Windows 8.1 under VirtualBox.

  (2) after that Windows 8.1 will appear, fix myDAQ on a USB port. If a pop-up window appears asking you to respond, ignore (at the beginning I did not ignore it and myDAQ transformed into a charger USB device firmware such as reported by Device Manager).

  (3) at this stage most likely "VirtualBox VM features-online USB Devices" drop-down menu shows "National Instruments NI myDAQ [0003]" as an entry but without a check mark to the left of the name. Bring the cursor to the left of the name and click here. You should now see a check mark there.

  (4) my myDAQ Self tests started working.

  However, I need the functionality provided by ELVIS as well. So I uninstalled http://www.ni.com/download/ni-daqmx-14.2/5046/en/ and installed from NI ELVISmx 14.0. My boot sequence that I have reported above, didn't work. Just at the moment it's just happened that Oracle has released Version 4.22 of VirtualBox that I wanted to try and ELVIS started to run. I can now use myDAQ DMM.

  One thing that contributed to my problems is fruitless attempts to uninstall the software OR. Unsuccessful uninstalls leave garbage behind who can or cannot cause problems in subsequent relocations. In one case, I'm done with the nidevldu (OR charger) service stuck in the system. I had to do a reset Windows 8.1 recovery operation to get rid of him. I decided to restart Windows 8.1 before uninstalling the software. This ensures that there is nothing in the limbo that past can interfere with a successful uninstallation.

• PXI-2530/2567/2593 Instrument map self-test

  Hello

  We will use the PXI-2530,-2567 module, &-2593 instrument cards in our chassis PXI-1044. We use LabVIEW software coding ATE platform. We would like to perform a self-test on the cards before the measures of the object to measure. Do you have any documentation that will support this task? The approach to check the functionality of card better by querying the records of the State of the map? In any case, I can't find any information online about this topic.

  Thank you!

  Dan

  Hi dan_tuq,

  That's all!  simply provide a valid handle for each call of niSwitch Self-Test VI.  Good luck!

  Kind regards

• Portege R500 - defective cdrom causes very common on self-test

  Hi all

  the internal CD-ROM drive in my R500 is no longer recognized. He went in the 'My computer' view in Windows XP. Sometimes he is shown as a unknown device in the control of the material, but most of the time that we show any. The cdrom still turns up to the insertion of a disc and seems to act "normal" (regarding the flashing of light, sound, etc.)

  Given that this fault has occurred, the power on self test takes about 2 minutes before the operating system is started later. In addition, the screen goes black for about a minute after it is finished with this startup resolved (Windows XP) first of all, low screen. Sometimes, the same occurs during closing.

  I don't know which is the reason why or if there is a third underlying cause, but he began to appear at the same time. Once activated the bios debug output, all the self tests have been printed as 'ok', but after the last test is finished, it is at a standstill (perhaps until some timeout kicks in).

  You have any suggestions or should I send it in (that would be quite unpleasant for me, depending on the machine)?

  Hello

  Are you sure that this problem is caused by the defective CD/DVD drive?
  Of course a material error could affect the power on self test (POST), but it is really hard to tell if it s caused by ODD.

  Hmmm, what you could do is remove the STRANGE to the laptop and to start the machine, in this case the MESSAGE should be transmitted correctly.
  If this isn't the case, so I doubt that the problem could be linked to the STRANGE

  However, if it s a hardware related issue, then the laptop should be addressed to the ASP in your country
  The R500 does not seem to be an old book so I guess that the guarantee is valid and the repair must be made free of charge.

• DPS self test on BIOS

  The hard drive self-test is completed, the completion code is 0 and what it means? I use the HP Compaq dc7800 Small Form Factor and the model number is AQ532US #ABA

  Code 0 means "Completed" in other words, no problem found.  Why did you run the test?

• Pavilion p6330f PC: SMART Test: SMART short Self Test FAILED

  I had so many problems with this computer. Whenever I have turn it off then go turn back will go to Recovery Manager. I did run the computer health check and did the basic test and Test drive both hard say Test INTELLIGENT: SMART short Self Test FAILED. What does that mean?!

  Hello

  It simply means: the HARD drive is about to die. Please save all your data if you could and be prepared to replace the HARD drive. Is your machine still under warranty? If so, please contact HP for replacement

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Kind regards.

• Satellite A500-1GL - fails self-test on start up

  My A500-1GL fails self-test on startup upward and freezes with screen Toshiba is innovation leader displayed. Try F2 for Setup and F12 for the boot menu in which two cases, in what it says entering start menu or enter the setup and remains like that.

  The manual even tried F7 to find the computer from scratch, but nothing, even the CD drive does not open. Very frustrating.

  Can someone help me with this please?

  Hello

  > F2 tried for menu setup and F12 for start in which menu two cases, she said entry menu or entering the Setup program starts and stay like that.

  It may be Bios or hardware malfunction. Sorry, mate, but I think you should contact the Asp (SAV). I guess your knees is small stream under warranty, so can be fixed for free

• SMART short self-test - on the second hard drive

  HP Pavilion Elite e9270t - 3 yrs old, Win7.

  Became the error SMART self-test short the original drive so I installed a replacement and transferred files.

  I get the same error on the second h/d. I have my doubts that the second disk is having the exact same error and wonder if the s/w test is actually the problem.

  It could very well be the connectors that gives you the question instead of the HARD drive itself. I would run the HARD drive test in BIOS instead of the short test.

  Try this:

  1. Plug the AC adapter into the computer if it is not already connected.
  2. Turn off the computer and wait five seconds.
  3. Press the power button to start the computer and repeatedly press the F10 key to enter the BIOS Setup menu.
  4. Use the right arrow or left arrow keys to navigate the menu selection to find the Auto test primary hard drive option. Depending on your BIOS, it is under diagnoses or tools.
  5. Select self-test primary hard drive, and then press the Enter key to start the test.

  Figure 1: Example of a primary hard disk self test screen

  
  

  The hard drive self test performs a Quick Test , followed by a complete Test. During each test, the window displays a status bar and a scheduled for completion

  Let me know the results of this test.

  THX

• What are the answers of code of HD521-2W SMART short self-test error when running the diagnostics?

  1 HP Pavilion a4310f, product # AY014AA-ABA, software Build A1NAv6PrA1

  2. Microsoft Windows 7 Home Premium (64-bit) Edition

  3 a receipt the "Failed SMART short self-test HD521-2W" when executing Hardware Diagnostic tools.  Error message:

  Error message the device reported the following State: the previous self-test completed having the read element of the test failed. 01/12/2012-06:21:01

  The first LBA value failure Error Message is 440642933 and the failure occurred after that the device was working since 7943 hours under tension.

  01/12/2012-06:21:01

  4. I made no changes to my system for over a month.

  Device: Hard disk WDC WD64 00AAKS-65A7B SCSI Disk Device, the revision of the firmware 01.03B01

  This unit is my hard drive (it is in factory with partitions C: and D: {Factory Image})

  Hello

  The Smart error code would indicate that the hard disk is running out and must be replaced.  If you want a guide on this, let me know.

  Kind regards

  DP - K

• RE: Hard drive that self-test - quick test successful and all by the long test he died.

  1 main hard drive that self-test - quick test successful and all by doing the test long it turns off. What could be the problem?

  2. I tried to recover with the recovery cd received the error

  1005 if this error persists then contact Hp support.? need to order another set of CD

  Reinstall the hard drive in the laptop.  Scroll down on this page and get > Bootable CD ISO and > ImgBurn to burn the iso image to cd, a guide on the use of ImgBurn to write an ISO on a disc is here. Once created, boot from it. Delete hard drive partitions, create and format. Then try to start recovery again.

• PCI-5922 self-test error-223431

  I try to reset PCI-5922 OR MAX and get the error code 80040383:

  "There was a problem of resetting the device."

  Then I try the automatic test of NOR-MAX and get the State Code:-223431

  "The self test failed.

  State code:-223431

  Internal software error has occurred in the extended software. Please contact National Instruments. »

  I have tried following th:

  1. reboot the computer

  2. Uninstall and reinstall OR-Scope 15.1.1

  3. change of PCI slot

  After a few tries it turns out that the problem was in the computer. When it is installed in a different computer, the PCI-5922 worked properly.

  Now, it seems obvious: when troubleshooting

  1.) install the Board in another computer

  2.) install another identical sign (if you have one) in computer suspiciuous

  Yonathan

• Add 9188 Chassis to the system definition file (sdf)

  I want to measure the basic in Veristand 2011 without a custom device channels.  In the system definition file, how can I add a 9188 chassis? And how do I add a thermocouple on channel 0 on a series c 9213 module?  Thank you!

  Hello

  You work with a Windows or device in real time?

  If you use VeriStand able to work with a Windows-based system, the addition of a cDAQ-9188 should not be a problem; the equipment Discovery Wizard he will come if it's in the same network as the Windows computer. Having problems with this?

  If you have a real-time like a Pharlap ETS PXI controller running target, you will not be able to use the cDAQ-9188 at all because it is not supported in real-time operating systems. If you work with a target in real time and you need the CompactDAQ you either move to Windows or we a USB CompactDAQ instead, like a cDAQ-9178.

  Please refer to this topic. The second post made by a Product Support Engineer and I was able to confirm that the information is still valid even for the latest versions of NOR-DAQmx and VeriStand. You can also check the compatibility in real-time in the Readme of NOR-DAQmx 15.5.

  Kind regards

• How many quadrature encoders may be read together with the cDAQ-9188 chassis?

  We will record position periodically 8 engines (at the same time as we are to the corresponding samples entered analog).  It seems that the 4 built-in counters limited chassis to 4 encoders.  Is this correct?  I am familiar with modules of counter PLC which manage high-speed counting, and then the CPU posts periodically to update the total values.  This is how the NI 9401 card would work?

  Hi jtrout,

  You are right the 4 built-in counters than the cDAQ-9188 chassis 4 encoders.  The following article deals with the use of the NI 9401 card for encoder measures: http://www.ni.com/tutorial/7109/en/.