9235 & cable length

Similar Questions

• Cable length of lightning.

  Lightning cables are available in various lengths, length improve or degrade its effectiveness?

  There is no difference in the effectiveness

• DK - 31 cable length

  I hope this is the right forum! No one knows the length of the DK-31 for the Xperia Z1 dock? It seems rather short in the pictures I've seen.

  Thank you very much

  The cable is approximately of ~ 90 cm long.

• Ethernet Cable length

  The distance between my Airport Extreme to my end 2012 21.5 "iMac is 20 meters .

  The Ethernet cable is CAT 5e ,

  1. upgrade to CAT 6 will make no improvement?

  2. is it compatible with CAT 6 Airport Extreme?

  Thank you...

  1. upgrade to CAT 6 will make no improvement?

  No, not really, since the two Ethernet category types are supported on the maximum bandwidth that the AirPort Extreme can handle.

  2. is it compatible with CAT 6 Airport Extreme?

  Yes.

• dock Onelink cable length

  Hello world

  I think to clean my office with a dock to onelink. Because I intend to hide the dock under the table, I would like to know, how long the onelink cable is. I couldn't find any info about this on the web.

  Thank you

  from memory, it was around 40 to 60 cm.

• C40 Camera control maximum length of cable RJ45 to d - SUB

  Hello

  What is the maximum cable length for the control of camera on a Cisco C40 port?

  Thank you

  Kyle

  According to the PrecisionHDMC camera Guide, page 17, the camera cables that usually come with codecs can be 5, 6.5, or up to 20 meters.  Anything more than 5 meters requires the camera powered by the power of the camera and not the codec using the camera control cable itself.

  I have a few installs custom where the camera control cable is well up to 75-100 feet.  Just follow the outputs pins on the same page as above to make your own cable and don't forget to use the POWER-CAM-V = power supply to power the device.

• Cannot connect by Satellite Pro projector if more than 3-4 m cable

  We have several laptops - and we have never had any problems that they might know an external projector.
  The length of the cable is normally around 10 m.

  Our Toshiba Satellite Pro laptops can only connect to an external projector if the cable length is less than 3 to 4 meters.

  What shall we do?

  Hello

  > Our Toshiba Satellite Pro laptops can only connect to an external projector if the cable length is less than 3 to 4 meters.
  It seems that the video signal is too weak and he cannot reach the appliance connected to the end of the cable.

  I found this info useful on this page that explains this behavior:

  + A normal PC, notebook or tablet PC VGA signal is not designed to operate on long cable runs. +
  + You can find only one kind of PC or laptop will work with a long cable to projector, and another type of PC or laptop may not work. +
  + However, this does not mean that the second computer is down. +

  http://www.RM.com/support/TechnicalArticle.asp?CREF=TEC333092

  _Solution: _
  The VGA signal must be amplified before it can be sent to the bottom of a long cable. These symptoms are all indicative of weak signal problems (or bad wiring).
  You should always use an amplifier VGA (active), Terminal VGA box (active) or a switching VGA (active) unit when you use along the VGA cables

  Good bye

• Cannot establish network connection. Messages on the icon alternate between "Acquiring network address" and "unplugged network cable.

  Original title: cannot establish a network connection

  Very well, a computer can connect to the internet. Another computer using the same modem cable and fixed connection of the router (for example using the port adapter, not wireless) Wireless does not connect. I suspect that there are has some settings somewhere that are not correct. Can you tell me how to understand where is the problem?

  Messages on the icon alternate between "Acquiring network address" and "unplugged network cable. When I run troubleshooting this is what I get:

  Diagnosis of IP Configuration
  Invalid IP address
  Info	Zero (0.0.0.0) detected IP address
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: reset the network connection
  action	Disabling the network card
  action	Activation of the card network
  Info	Successfully activated network adapter
  Info	Zero (0.0.0.0) detected IP address
  action	Repair Manual: Reboot modem
  Info	AutoNet address detected: 169.254.225.103
  action	Auto repair: renew the IP address
  action	Release the current IP address...
  action	Successfully published the current IP address
  action	Renew the IP address...
  error	Error to renew the IP address: the semaphore timeout period has expired.
  Info	AutoNet address detected: 169.254.225.103
  Info	Redirect the user to support call

  WinSock status
  Info	All base service provider entries are present in the Winsock Catalog.
  Info	Winsock Service providers strings are valid.
  Info	Entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.
  Info	Entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.
  Info	Entry provider RSVP UDP Service Provider managed the loopback communication test.
  Info	Entry provider RSVP TCP Service Provider passed the loopback communication test.
  Info	Connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter
  Network location detection
  Info		Using the Internet connection at home
  Identification of network adapter
  Info	Network connection: name = Local 2, Device network connection = Intel(r) 82562V-2 10/100 Network Connection, MediaType = LAN, type = LAN
  Info

  Ethernet connection selected

  State of the network adapter

  Info

  The network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn

  FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn

  HTTPS: Error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  warn

  FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  warn

  HTTP: Error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  error

  Could not make an HTTP connection.

  error

  Could not make an HTTPS connection.

  error

  Could not make an FTP connection.

  I found the problem (s), even if I am always left with a few questions.

  During this process, I have disabled the firewall, but that did not help. However, I noticed 'tweaks' accessed via the tab 'Advanced' in 'Microsoft Firewall' which looked like, they must be checked in order to access the internet. I checked these and reintroduced the firewall. After I got things working, I unchecked them and things still worked so I obviously don't understand what these parameters.

  The solution:

  (1) I have to go straight from the modem cable to the computer. I can't have a cable modem, router wireless, computer, even if using hard wire, and even if this same configuration works with another computer. Also, I can't use a cable length to go from modem to the computer. So, it seems to have had a problem of cable length. Power problem? Only connected to this computer devices are the mouse, the keyboard and the Ethernet. Would not this be fixed with an upgrade of the power supply? Or is it due to the quality of the Ethernet hardware on the motherboard? It's a Dell Vostro 200.

  (2) in back and forth between configurations while following the problem, you must think to unplug the modem to reset between each configuration. You may have stumbled upon the solution, otherwise he's not shot. Also, I unplugged the cable from the modem when you reset data cable - do not know if it was necessary. I wanted to limit the degrees of freedom that I had a lot, as it was.

• N2000 and N3000 stacking cables

  Hello

  I have a small question.

  0, 5 m, stacking of cables (N2000 and N3000 series) enough to connect the switches that are 2 RU independently of each other?

  The plan is to have two panels of brewing between switches (24 p, 48p 2x24p, 48p, switch panel, switch panel,... and so on) and I'm not sure if 0, 5 m battery cables will be sufficient or do I go with cables of 1 m... on the pictures it looks like connectors are long enough and I'm not sure if 0.5 refers to the length of cable length of connectors witch included or not.

  Kind regards

  Jakub

  Jakub

  If the switches you are trying to stack are only 2RU apart, then all the support cables should work, including 0.5 m.  With the help of a cable management system, stacking more cables such as 3 m can allow routing around the patch panel ports.

  B

• PowerConnect 6248 P do not stack with 12 m cable

  I try to superimpose 2 PCT6248P via the cx - 4 12 m stacking cable and it does not work. the two starts as master 1/7 and do not see each other, even if it is started before the other when I use the stacking of 1 m cx-4 cables, they work perfectly, even on reboot if I replace the cable of 1 m with 12 m stacking cable they remain in the configuration of the battery until they have restarted. the two run the firmware version 3.3.10.3 I changed the cables to check that they are not the issue. Help?

  Maximum cable length that can be used for stacking is 3 meters.

  www.Dell.com/.../pwcnt_stacking_switches.pdf

• Mixture of Cat5 and Cat6 LAN cable

  What happens when you mix the cat5 and cat6 cables? For example from the desktop for cat5 (100 Mbit/s) patch panel and from the switch to the cat6 patch panel that supports Gbps. It will create problems?

  avilt wrote:
  What happens when we mix cat5 and cat6 cables? For example from the desktop to patch panel it's cat5 (100mbps) and from the patch panel to the switch cat6 which supports gbps. Is it going to create any issues?
  

  Nope.

  Your connection will be held at the common denominator - for example, if you have a part of the cable which is Cat5 and Cat6 - the rest is cable length behaves as if it had * everything * Cat5.

  If your workstations will get a Cat5 grade connection to 100 Mbit/s bit matter what you hang on the switch.

  See you soon.

• Simulation of cable

  Hey all. I'm trying to get a line of cable - watching him work. I found the post of kglad last year, but it doesn't seem to be a general solution (using Flash 8; there incompatibilities?). In particular, when catenaryApprox is passed to mouse x and ymouse for the first pair and a constant for the second pair, the parabola becomes horizontal when the mouse is near a line abs (*(t-a) b k), where k seems to be an exponential function of the cable 'length' and a and b are the coordinates of the constant pair for the second point.
  
  Above this line, all behaves as it should. Below this line, the parable reverses; close to this line, the parable goes horizontal. I suspect that it is a result of the approximations used, but I have no evidence of that. Someone at - it is possible to duplicate these results? I had problems in the past with the corrupted installations of Flash Player.
  
  Curious monkey, kglad, where these equations come from it? I see that you find the point of intersection, but whence derivatives?
  
  I'm trying to expand the equations for crtlX and crtlY, so I can understand why it explodes; I also try to find a quick way to correct the inversion of the coordinate y kglad code is attached. I found several good references to
  http://www.Tinaja.com/glib/bezcat.PDF
  http://whistleralley.com/hanging/hanging.htm
  http://en.Wikipedia.org/wiki/catenary
  
  Any help is appreciated. Thank you very much.

  Okay, so I had to play around with this and I came up with the following solution. He made no claim that either a mathematical accuracy, but it seems all right and even looks like it 'is short of cord. Thanks a lot for your time, kglad. Simply attach the code attached to an empty clip; It generates a curve as the location of the item to the location of the mouse pointer.

  EDIT: Looking at, I noticed that it does not have much to play nice with the stratification system. Maybe that's a problem; He could not. I have not tested.

• cannot fine internal power supply form new sound card

  Just installed the asus xonar dx card in my slimline s5670t office. The problem I have is that I can't find the power supply 4 pin I need on the mobo. Can someone help me?

  Here are thespecifications of the motherboardof your PC.

  You probably need to look for a connector 4-pin molex or floppy disk which cuts off the power supply.  If your don't see a spare connector, then you will need an adapter for the splitting of a molex connector or even disable a sata power connector.  Look carefully at the power cable goes on the hard drive.  That's where you could try a power cable Y splitter.  www.Newegg.com has probably want you need.

  Maybe thisadapterwould work.  I can't tell if the connector is good to type the disk sata for power or if the cable lengths are long enough.

• Interference between the capsules of the time when the erasure of a time capsule

  I have a couple of old time capsule and base stations to the airport that I need to clear before you sell or give their.  They have some settings that are the same as my current active Time Capsule including the name of the device, network name and.  I am concerned by the deletion time capsule to interfere with my active Time Capsule wireless.  Do I have to close my TC active erasing one of the old TCS or airport base stations so that it does not interfere with the Active TC wireless?  I plan to make the deletion process via a cable ethernet from an another iMac located two floors below the Active TC in.

  Temporarily turning off the current active Time Capsule.

  Connect your MacBook Pro or another laptop computer directly to one of the three ports LAN <>- on the Time Capsule Ethernet to alternatives including the drive you want to erase using a short cable... is going to any Ethernet cable length.

  Then, the same thing to the other time Capsule with the drive you want to erase.

  If you don't have a laptop to use, then move each time Capsule to be cleared near the iMac and connect the iMac directly to one of the three ports LAN <>- on the Time Capsule and perform the operation of deletion in this way.

  If you plan to keep the two Time Capsule that will be deleted, you can use Quick erase procedure, which takes only a few minutes.  However, if you plan to spend the Time Capsule (s) to another person, you must perform a safer Zero data on the Time Capsule (s).

• Re: My Satellite Pro P300-19 q there Firewire 400mbps, 800 or 1600?

  Which firewire connection my Satellite Pro P300-19 q did?
  I hope that this goes up to 800mbps (IEEE 1394 b) so I can use a powerful Firewire Soundcard for Audio recording of high quality.

  The only specs State he has IEEE 1394, but not the State is there, B, C or D

  IEEE 1394 - Firewire 400

  * Speed: 400Mbps
  * Cable length: 4.5 m

  IEEE 1394b - Firewire 800

  * Flow rate: 800Mbps
  * Maximum cable length: 100 m

  IEEE 1394b - Firewire 1600

  * Flow rate: 1600Mbps

  IEEE 1394b - Firewire 3200

  * Flow rate: 3200Mbps

  Hello

  I don't have any idea what firewire port is, but you should be able to know the installation details of material diagnostics such as SiSoft Sandra or Everest Home Edition.

  These tools, one for free and will help you diagnose the hardware.

  Welcome them