A few questions about NB505-N500BL

Similar Questions

• Satellite L650-11R - a few questions about this

  Hello there :-)

  I have a few questions about my new L650.

  I've never had Toshiba notebook before so I apologize if some of these "quirks" are actually quite normal on this laptop. I really want to hear the views of other users L650.

  1)
  First of all, by the time I turned it on I saw gradient thin (1-2 mm) along the right edge of the screen that goes from the bottom up. Maybe "degraded" isn't the right word, but it seems that since two or three pixels are kind of discoloration or lose brightness/sharpness to the edge along the straight bezel. It is not really that visible, looks like the colors are desaturated a bit here or brightness is a bit lacking. He can be seen everywhere (bios or no color in Windows, but better in the lighter background).
  The left side (or other) seems ok, all this along the right edge is somewhat suspicious. If one can compare? I don't know if it's something to worry about or is just supposed to be like that.

  2)
  The other thing I noticed heating of the processor (Intel i3 330M) and GPU (ATi Mobility Radeon 5650). It's pretty hot here right now (I would say that the temperature is around 28 degrees Celsius when using cell phones). He is sitting on the hard surface (table) and nothing is blocking the vents.
  However, at "rest" (surf the web & regular light stuff), average CPU temp hovers around 58 ° C. It usually goes from 45 to 62 in just a few minutes after starting, and then I can hear and see (Toshiba PC Health Monitor) evacuate the kicks in. Temp goes back to 50 +, event stops and then the temp rises to 60 + until the vent is used again.
  During load full (Prime95 or some games), CPU is going all the way up to 75 degrees (the highest being 77). Fan runs at 75 to 77% during this time, never go faster.

  GPU idling is usually around 5 degrees above temp CPU (62-65). During full load (for example. Benchmark of Far Cry 2), I see a lot of stuttering with the latest drivers Catalyst and DX10 (not sure if the stuttering has something to do with heat), otherwise it is ok (no artifacts or anything like that). Temp of GPU during the loading goes up to 74-75, fan speed is locked at 30%, the frequency of the heart 5650 is 450 MHz. left side of the laptop (vent and below) is pretty hot, while the keyboard is warm (or slightly warmer who who).

  These time seems correct and safe in the long term? I'd rather events works all the time (they aren't really very strong) and keeping time less than 50, but there are just wishful pious bios control events and I can't control not the bios. :-)

  3)
  This is just General related products. :-)
  Official specifications of Toshiba L650 say ATi 5650 (between other low range GPU), but I saw a few specifications calling for there 5730 (same model 11R). Is there really a Satellite L650 with ATi 5730 GPU models?

  Sorry for the long post, I tried to include the best possible description that I could do. :-)

  Thank you in advance.

  Thanks for the additional info!

• A few questions about the Satellite A100 PSAANE

  Hi friends,

  I have a Toshiba Satellite A 100 - PSAANE with Vista Home Basic preinstalled in it.
  Now, I have a few questions... I mention below: -.

  (1) if I want to format my laptop, I need a CD to install for Vista Home basic... then I don't have this Toshiba CD when I bought the laptop. So how do? question: How can I format it?

  (2) can I change my Vista Home Basic to windows XP? I think it's much faster than this one. is it advisable?

  (3) I have a GB of RAM in the laptop. Increase the RAM? I think that my laptop has become to slow down. is it advisable?

  (4) and on my screen, everytime I try to change my profile screen to windows Classic view, my screen begins to blink. and after a while, the screen turns off. So I can't change that. I put the color scheme of windows vista only. What to do about that?

  Please help me friends. Thanks in advance.

  Kind regards
  Perkins

  Hello

  Here, a few questions about the number:

  (1) usually, you should get the Vista Toshiba Recovery DVD. If you didn t receive this DVD then you can order it here https://backupmedia.toshiba.eu/landing.aspx or you could install the disc of Microsoft Vista.

  (2) of course, you can do this. I think that Win XP drivers can be downloaded from the Toshiba driver page.

  (3) Yes, you can upgrade the RAM. For more information, see your manual or search on this forum for similar topics

  (4) maybe it s associated with the graphics driver. Check if you can update. I would recommend additional check if you are using the latest version of the BIOS

  Welcome them

• A few questions about Toshiab reocvery disk for Satellite P300-133

  Hello guys,.
  I had a few questions about unpleasant surprises of recovery:

  (* 1) * I just make recovery DVD using Toshiba Recovery Disk Creator and he asked initially for 2 DVDs - but when one has been done it does not require a second blank DVD. Is it possible all the Windows Vista system files to write on 1 DVD?

  (* 2) * if I could reinstall Windows Vista using recovery of HARD drive option (by pressing F8) without using the recovery DVD?

  (* 3) * HARD drive partitions that will be formatted (just system C: or C: and E :) using HARD drive recovery?

  (* 4) * what is DVD - Image of the hard drives or the installation of Vista recovery files?

  Its pretty bad idea to not include BONES on DVD when I paid for it.
  Thanks for all the Toshiba problems :(

  1. I think the recovery disk creator means 2 CDs. I also have a Portege M700 with Windows Vista and a DVD. I got it and after that, I have a clean install of Vista with all the drivers and tools of Toshiba. Nothing is missing.

  2. Yes, you can reinstall Vista using recovery of HARD drive option when you press F8 at startup. You don't need the recovery DVDs, but you should create a when your HARD drive get some errors or something else. If you need a new recovery DVDs, you paid for one.

  3 HARD drive and complete partitions will be formatted, so backup your data first on a DVD disk external DRIVE, USB stick or something else.
  After the reinstallation, you have factory settings.

  4. the recovery DVDs is an image of the HARD disk on the factory settings. If you perform a recovery, there are all the drivers and tools are already installed. Of course, on the disk are files of installations of Vista, but you can use this DVD on your Satellite P300. The disc cannot be used on another Satellite or on a PC.

  If you have any other questions, take a look in the user manual. There are a number in the formations of the recovery. It s in Chapter 3.

• Hello Mr President! I have a few questions about the Word report generation please.1.How can I add a border to a page in word? 2. How can I add gridlines to a table generated related word?. Can 3. how I add a border to a picture of the Word report?. Thank

  Hello!

  Sir, I have a few questions about generating word reports using (C language in labwindows) please.

  1. How can I add a border to a page in word?

  2. How do I add border lines and grid to a table generated in Word report (not "cvi control table"inserted from gui, I wonder about the table generated in Word report)?

  3. How can I fill a table cell of report word with the data type other than 'character '.

  And sir a question on the use of the timer in labwindows cvi please.

  Sir, I'm trying to set a time minimum interval timer to 1millisecond (0.001 s), that I have set, timer cares about the interval set by me he only meets the minimum default time interval which is, I think as 10milliseconds (I'm using windows xp service Pack 3 version 2002).

  Concerning

  Imran

  Pakistan

  Have you read this statement ? It explains how to set the registry value:

  If the REG_SZ useDefaultTimer does not already exist, you must create it under HKEY_LOCAL_MACHINE\SOFTWARE\National Instruments\CVI Run-Time Engine\cvirte. "" This can be done navigate to the appropriate folder, and then click Edit "New" string value. Then, click on means the name of the new value created, select Rename, and then specify useDefaultTimer as the name. Finally, double click on the name and specify the value True or False.

• A few questions about the use of data and Cliq

  I have the cliq, however I chose to not get 3G (so I bought full fare). So I have a few questions about the phone and the use of 3G / 2 G/Edge:

  1 - is possible to disable completely the 2G / 3 G/Edge? I know you can switch between them, but are anyway just tell the phone to stop using them altogether since I'm not subbed to the service?

  2. when the update takes place, I guess we'll have to reconnect motoblur and etc, but if I don't have 3 G will I have motoblur connection problems after the update? Or he keeps the latest wifi settings so that it would connect to wifi to connect. When I first got my phone it was not a problem b/c I had 3G for the first month.

  I hope that makes sense, thanks!

  To stop all the data, I would like to download an application called APNDroid. He cut them all down. When you log on to blur you have 3G or WIFI doe this without getting a timeout error. During the process of setting up your Blur account, you can press the menu button and set up your wifi to work, this will connect you to Blur and your phone will be connected to the blur. If I were you I would be rethinking to do a data plan since you are really losing out on most of your main features of phones. It's your choice, however.

• Recently bought a laptop computer; A few questions about the offer Upgrade to Windows 8

  I have a few questions about the Upgrade of Windows 8 offer for new computers.  I recently bought a Toshiba Satellite S855-S5268 of amazon.com, which came with Windows 7 Home Premium.  Toshiba already has a beta version of drivers and utilities for Windows 8 for the S855 on their Web site.

  (1) I bought my laptop in July of this year, and I've not yet registered for 8 Windows Upgrade offer with Microsoft.  Am I still eligible to receive the upgrade, if I sign up soon?
  (2) if I buy the upgrade through this offer, I'll be able to download an ISO file so I can burn the installation media, or do I need to upgrade to Windows 7?
  (3) if I will be able to burn the installation media, I'll be able to erase my hard drive and do a clean install of Windows 8 (which I'd rather do, I have a lot of backups of my data).  I am aware that I would probably need to provide my product key Windows 7 Home Premium 64-bit OEM during the new installation, because it is an upgrade and not a full version; This isn't a big deal, because my Windows 7 Home Premium 64-bit OEM product key is stuck at the bottom of my laptop.
  (4) my current copy of Windows 7 is activated by seeing my BIOS (I have a traditional BIOS, not a UEFI).  If I had to switch to Windows 8 and decide then I'd rather back in Windows 7, for example, a few months later, I'll be able to do that (I burned recovery of Windows 7 with the Toshiba utility disks, which I did), and Windows 7 will continue to activate by seeing my BIOS, even after the installation (and later remove) Windows 8?
  Thank you very much!

  I have a few questions about the Upgrade of Windows 8 offer for new computers.  I recently bought a Toshiba Satellite S855-S5268 of amazon.com, which came with Windows 7 Home Premium.  Toshiba already has a beta version of drivers and utilities for Windows 8 for the S855 on their Web site.

  (1) I bought my laptop in July of this year, and I've not yet registered for 8 Windows Upgrade offer with Microsoft.  Am I still eligible to receive the upgrade, if I sign up soon?

   

  Yes, the registration period is between June 2, 2012 to January 31, 2013.

  (2) if I buy the upgrade through this offer, I'll be able to download an ISO file so I can burn the installation media, or do I need to upgrade to Windows 7?

   

  Yes, the Upgrade Wizard of Windows 8 will allow you to create a bootable DVD or you can grab the ESD file and save it.

  (3) if I will be able to burn the installation media, I'll be able to erase my hard drive and do a clean install of Windows 8 (which I'd rather do, I have a lot of backups of my data).  I am aware that I would probably need to provide my product key Windows 7 Home Premium 64-bit OEM during the new installation, because it is an upgrade and not a full version; This isn't a big deal, because my Windows 7 Home Premium 64-bit OEM product key is stuck at the bottom of my laptop.

   

  Yes and there are better ways to reinstall Windows 8 without using the installation disc, you can use the reset and refresh.

   

   

  These steps will take you through refreshing your PC:

  · Press the Windows key + C on your keyboard to show the charms (if you use a touch screen: touch the right edge of your screen and drag your finger to the left)

  · Click settings

  · Click change PC settings

  · Click general in the left column

  · Under refresh your PC without affecting your files, click Start

  Then follow the instructions that will be provided on-screen to cool your PC.

  (4) my current copy of Windows 7 is activated by seeing my BIOS (I have a traditional BIOS, not a UEFI).  If I had to switch to Windows 8 and decide then I'd rather back in Windows 7, for example, a few months later, I'll be able to do that (I burned recovery of Windows 7 with the Toshiba utility disks, which I did), and Windows 7 will continue to activate by seeing my BIOS, even after the installation (and later remove) Windows 8?
   
  As long as you have a recovery disk which you should create or use the construction in the recovery partition, Yes, it will self activate.
  Thank you very much!

• Hello, I have a few questions about the affiliation of creative cloud

  Hallo,

  I have a few questions about the affiliation of creative cloud:

  1. There is an Adobe offer up to 27.11. : the price offered is 47.59 euros per month including MWSt (VAT) or €568,20 / year.

  For what is this offer period/how many years valid?

  2. after the period of the offer, the membership will cost the standard-price: €59,49 / month or €713,86 / year (seen on the Adobe Web site).

  For how many years this standard - the price is fixed?

  Is the standard-prices include MWSt. (VAT) too?

  Thank you

  Thomas

  Hello

  I advise you to contact Adobe sales for queries on pricing.

  Contact us | Adobe

  Kind regards

  Sheena

• a few questions about vcloud

  I have a few questions about vcloud.  Currently, we use labmanager and are testing vcloud to see how we can apply it to our environment.  The current labmanager serves the following purpose:

  -create dev and QA 'environments' (configurations) that are copies of production servers so that the changes can be tested

  -environments deploy everything from models that are clones of production servers that we update as required

  -We have several models of "database" that freshen production according to the needs in order to provide a current recuree version of the database of production for these environments

  -computers in virtual environments are able to talk to each other using their 'production' IPs, because IP addresses are closed and accessible only internally within the

  -Each VM has an "external IP" that we can use to access the virtual machines from outside the environment.  for example, access a Web site through the front-end server within the environment, or RDP to a windows virtual computer within an environment.

  I am trying to determine how this translates into vcloud configuration, and I think I have a rough idea.  However I have a few questions:

  As I understand it, has no way to RDP to a virtual machine in a paralytic 'environment' unless the virtual machine is directly routed, correct?  In other words, we cannot copy the configuration that we have above, where the virtual machine has an internal IP address that corresponds to the IP address of the server in production and is used to refer to other virtual machines in the same environment of vApp, however there is also one external IP address, we can use to access this virtual machine via RDP or access its site Web etc.?

  I have 2 servers windows 2008, I imported as models, and each time I deploy a virtual using the VAPP model computer, the server seems to restart after 15 minutes be on is, and it seems to go through a windows installation, where it says "preparing your system for a first use" etc.  And when it arrives, the administrator password I put is no longer correct (so I have no idea why / what it changes the administrator password).  At this point, the virtual machine is useless since I can't connect to it.  No idea why this happens each time I have deploy a model VM?

  We talk here: http://www.yellow-bricks.com/2010/09/15/vcd-networking-part-3-use-case .  Not exactly a step by step for your case to use, but you should be able to get this up and running and configure NAT in the opposite direction.

  -KjB

• a few questions about the migration of content/web content

  Hi all
  
  
  I have a few questions about the migration of the website and content (from development to test) which are not specified after reading the oracle documentation.
  
  -> When we make the site replication will be migrated content (data files).
  
  -> when we move will contained all the ED and RD etc (any object type web site migrated).
  
  --> are the two the necessary step for migration when we migrate web site.
  
  
  Thank you
  
  -Yves

  --> When we make the site replication of the content will be migrated (data files).

  It depends on how you do it. The tool 'Site Studio Replicator' won't move any content, only the structure of the site. The 'Manage replication Site' page can be used to migrate content with the structure of the site but I do not recommend for large sites, I use separate tasks to archive to move the content. "Backup and restore" page stores the entire site in a ZIP file, not advisable for large sites.

  --> When migrate us content will be all ED and RD etc (any object type web site migrated).

  Yes. It uses the metadata xWebsites field to identify the elements that belong to the site.

  --> are the two the necessary step for migration when we migrate web site.

  Depends on how you do it, but yes, all bits are needed.

• EBS 12.1.3: a few questions about cloning

  Hello
  
  We have EBS 12.1.3 on AIX 7.1.
  
  A few questions about the cloning of level shared environment of application layer non-shared application environment. We followed 'Cloning Oracle Applications V12 with rapid Clone [ID 406982.1]'
  
  Environment (shared application layer) source:
  -Two nodes in the active application and LBS
  -A database of active and a passive database configuration with Oracle Data Guard.
  -Terminate SSL at the load balancer
  -Updated CFP implementation
  
  Environment target (level app not shared):
  -A single node of the application active
  -One data node active
  -Without SSL
  -No PCP
  
  After the cloning was completed, we noticed the following problems in the target system:
  
  (1) home page is not available because application $CONTEXT_FILE layer always contains the endpoint "https" and ssl settings.
  
  Workaround solution:
  
  Change (with text editor) layer Application $CONTEXT_FILE as follows.
  < webentryurlprotocol oa_var = "s_webentryurlprotocol" custom = "yes" > http < / webentryurlprotocol >
  < sslterminator oa_var = "s_enable_sslterminator" > # < / sslterminator >
  < login_page = "s_login_page" custom = 'yes' oa_var > http://myhost.mydomain.com:8000/OA_HTML/AppsLogin < / login_page >
  < externURL oa_var = "s_external_url" custom = "yes" > http://myhost.mydomain.com:8000 < / externURL >
  
  Run the automatic configuration service and application layer.
  
  Is there a better solution and supported for this?
  
  (2) simultaneous managers do not work properly, because they still have old names of node (used in the CFP in the source system). The solution is used:
  
  1. connect to the EBS GUI web and delete all nodes of all concurrent managers.
  2 shutdown application layer. Check that all concurrent managers have been extinguished. If not, kill the process manually
  3. as a user apps run cmclean.sql
  4 restart the application layer
  
  Is there a better solution for this?
  
  (3) database ARCHIVELOG mode nonarchivelog mode changes in the target system. Is anyway to prevent this?
  
  (4) in addition, we would like to make a full clone (app + db levels) of production without closing the application. Is this possible? What would be the best documents to describe it? In Production, we have Oracle Data Guard physical standby installation as per "Note technique Oracle: Business Continuity for Oracle E-Business release 12 Using Oracle 11g Physical Standby Database [1070033.1 ID]. This can be used when executing a clone of warm for the database, right? What application layer? The steps in 406982.1 include AutoConfig in what application level should be running down. Must the application be broken when running "to maintain the Snapshot information?"
  
  (5) one last question (not related to cloning). Oracle Enterprise Manager console webUI has recently stopped working in IE8. For example, https://myhost.mydomain.com:5501 / em gives "cannot display the Page. It was working properly last week. In Firefox, the same link works fine. Any ideas how to solve this problem?
  
  Thanks for your replies in advance.
  
  BR,
  TH

  (1) home page is not available because application $CONTEXT_FILE layer always contains the endpoint "https" and ssl settings.

  Workaround solution:

  Change (with text editor) layer Application $CONTEXT_FILE as follows.
  http
  #
  http://myhost.mydomain.com:8000/OA_HTML/AppsLogin
  http://myhost.mydomain.com:8000

  Run the automatic configuration service and application layer.

  Is there a better solution and supported for this?

  No, you must modify the context manually and run the automatic configuration.

  (2) simultaneous managers do not work properly, because they still have old names of node (used in the CFP in the source system). The solution is used:

  1. connect to the EBS GUI web and delete all nodes of all concurrent managers.
  2 shutdown application layer. Check that all concurrent managers have been extinguished. If not, kill the process manually
  3. as a user apps run cmclean.sql
  4 restart the application layer

  Is there a better solution for this?

  You follow the best approach. You could update the details of the server node if you wish.

  (3) database ARCHIVELOG mode nonarchivelog mode changes in the target system. Is anyway to prevent this?

  By default, the quick Clone will create the target in noarchivelog mode database.

  (4) in addition, we would like to make a full clone (app + db levels) of production without closing the application. Is this possible? What would be the best documents to describe it? In Production, we have Oracle Data Guard physical standby installation as per "Note technique Oracle: Business Continuity for Oracle E-Business release 12 Using Oracle 11g Physical Standby Database [1070033.1 ID]. This can be used when executing a clone of warm for the database, right?

  Fix.

  What application layer? The steps in 406982.1 include AutoConfig in what application level should be running down. Must the application be broken when running "to maintain the Snapshot information?"

  You can copy the files from the application tier node, while demand is rising. And, there is no need to stop the application to run "to maintain the Snapshot information."

  (5) one last question (not related to cloning). Oracle Enterprise Manager console webUI has recently stopped working in IE8. For example, https://myhost.mydomain.com:5501 / em gives "cannot display the Page. It was working properly last week. In Firefox, the same link works fine. Any ideas how to solve this problem?

  If it works from a browser, then it should not be a problem of EM. Have you tried another client and see if it works? Have you changed a setting in your Internet Explorer browser? Please make sure you add the URL of the EM to the list of trusted sites.

  Thank you
  Hussein

• A few questions about the colors of Patone

  I have a few questions about patone color since it is the first time that I use. I want to use them to create a paper letterhead and business cards in two colors.

  1)

  I don't understand that no sex is more than coated patone washed out colors. I heard that it's because the way paper absorbs the inkt. That is why the same results inkt in different colors on different papers (right?). My question is why is the patone black no sex so different than black normal (c = 0 m = 0 y = 0, k = 100) or black intense:

  

  When I print a normal document with cmyk, I can get pretty dark black color. How is it that I can't have this dark with patone color black color? Even text documents printed on a cheap printer can get a darker color than the color of Patone. He looks way too grey for me.

  (2) a first model, I want to print of patone in CMYK color (since I have like 10 different colors on a page of quick comparison). I know these CMYK colors distinguish the colors of patone and I can't get a representation of 100%. But is there a way to convert patone CMYK values?

  I hope some of you can help me with my questions.

  Thank you.

  You can get shades CMYK Pantone in Illustrator, (Swatches Panel > Open Swatch Library > color books > + PANTONE Color Bridge Coated or lying) but in my opinion, what's the point?  If you print to a digital printer, just use RGB (HSB) or CMYK. Personally, I never use CMYK called "equivalents." from Pantone

  Pantone colors are all mixed pigmented inks, which are fluorescent beyond the limits of the range of RGB and CMYK in particular. The original Pantone Matching System (PMS) was created for the printing industry. He described formulations of ink pigmented for each of its colors.

  Most digital printers (laser or inkjet) use CMYK. The range of CMYK is MUCH SMALLER than many mixed inks, printed on papers either paved or unpaved can deliver. When you specify no sex Pantone ink in artificial intelligence, according to Pantone conversion tables, HAVE "about" what will look like this color on a sheet no bed, try using CMYK. -In my opinion, this has little relevance to the real world conditions and should be avoided in most situations.

  If your project must be printed on a press printing with Pantone inks spots, then by all means, use Pantone colors. But don't trust the colors of the screen; rather get a Pantone swatch book and watch real inks on paper lying and uncoated, depending on the stock you will use on the press.

  With printing decreases rapidly for inkjet and web printers, Pantone has attempted to expand its relevance beyond the traction-date of publication (in the books and software alliances, with one such as Adobe) his old PMS inks and their supposed equivalent LAB and CMYK. I say "supposed" because even once, monitors RGB and CMYK inks can never be literally equivalent to many Pantone inks. But if you go to your project on a printing press printing, Pantone inks are still very relevant as of the "tones".

  I also put my preferences I > appearance of black both display all blacks accurately and output all blacks accurately. The only exception to this may be when you print on a digital printer, where there should be no problem checking.

  Rich black in artificial intelligence is a phenomenon of the screen, at least in the Prefs > appearance of Black, you specify also "out all inks like Rich Black"-something I'd do it EVER do so out for a real printing press. Still, I put my black people in artificial intelligence at the "output All Blacks Acurately" during a press release. If you fail to do so, then the press you will see any minor issue registration, with C, M and look at the back, especially around black characters.  UGH!

  Good luck!  :+)

• A few Questions about the advanced Actions window

  Hello

  I have a few questions about the progress of the Actions (using the version of track CP7)

  1. What is the function of the action to "continue?"   Out of the peak action and advance the playback cursor?

  2. What does mean this comment "Nested calls to action advanced is a nice improvement."? Is the advanced decision at the top of a page of action tabs?

  3. What is the function of the option "custom" in the IF statement - "preform action if - custom", it doesn't seem to do anything for me?

  4. where can I get information about the timeline / playhead interaction with advanced actions, i.e. where the playhead is going again at the beginning of the slide. slide custom question - display button, e.g. verification of responses, comments - when all the objects are at the beginning of the timeline. I'm looking more for the read head of infromation functionality rather than how to implement this type of question.

  Thank you

  Donal.

  Continue: If an advanced standard action is triggered by a button, this will not trigger the playback head. If you want out, you can use continues. Continue can also be a choice in a conditional action, when one orders branching has nothing to special, but in advance. Continuous is also the "dummy" statement/command (this is the official name of a line in the dialog box advanced actions) If a statement has become unusable due to some reasons, it will be replaced by continue

  There is no nested call stocks advanced possible right now, one of my many feature requests. It would be sort of a subroutine that you can use over and over again, instead of having to create each time when necessary.

  A decision is one of the conditions to be an advanced conditional action. They allow to create more complex actions, as a loop or arrays are not possible. All decisions are executed in sequence and always.

  Custom: is a combination of or but it is rather limited, because you cannot use parentheses.

  I guess you'd better visit my blog if you want to learn more about the advanced actions.

  http://blog.lilybiri.com/

  I also did several Webinars on stocks advanced, last this afternoon (on the sharing of the actions) for Adobe. They are all available on request.

  Lilybiri

• A few questions about in-app apple purchases

  Hello

  I would like to ask you a few questions about in-app purchases from the itunes store.

  I would like to create an application and put this app on the itunes store.

  The application itself will be a 'container' and contain 1 pound. The app will be free.

  So far so good. Now, I want to use shopping app from apple to sell the other books in the application.

  So that they will see a new book in the app and will be able to buy it.

  Now to my question:

  I would like to have books available in the form of separate .swf files (.swf files because I want to add an animation). If people can go to the itunes store and the swf will be downloaded on their device.

  Apple will actually allow this? And if not, anyone know how I could get what I want?

  Yes, that's what it means... Remember that you are not playing in the classic environment of Air, so your application will be just impossible to run any code from any SWF loaded. The reason is obvious: Apple doesn't want that any developer to extend applications or provide additional content without to have approved by Apple / earn money with it.

  In your case, I recommend you to include all the books hard connected by the swcs and then just unlock everytime the user pays.

• A few questions about integration between POET and EBS

  Hi you
  I am a new bie BIEE. In those days, have a look at the POET architecture and BIEE components. In the next project, there is some work on the development of POET based on request of the EBS. I have a few questions about integration:
  
  (1) generally, the POET application and database server is decentralized with application and database EBS? Both BIEE 10g and 11g version can be integrated with EBS R12?
  
  (2) in the POET administration tool, the first step is to create arrays of physics. If the source application is EBS, is it still necessary to create the physical tables?
  
  (3) if the physical creation of tables is needed, how to transfer data from the source of BSE BIEE physical tables tables? What ETL tool is preferred for most of developers? generator for warehouse or Oracle data integration?
  
  (4) during the data transfer phase, there are many many large data to transfer, how to keep the entire? for example, it must transfer 1 million lines of source to physical tables BIEE database, when 50% is completed, users try to open the POET report, they can see the new data of 50% on the reports? is there some transaction in phase control ETL?
  
  could someone give some pointers for me? I am very appreciated if you can also provide any other information.
  
  Thanks in advance.

  (1) generally, the POET application and database server is decentralized with application and database EBS? Both BIEE 10g and 11g version can be integrated with EBS R12?

  You shud look at OBI request here that uses OBIEE as a tool for reporting with pre-built modules. 10g & 11g comes with different versions of the applications of BI that supports sources such as Siebel CRM, EBS, Peoplesoft, JD Edwards, etc...

  (2) in the POET administration tool, the first step is to create arrays of physics. If the source application is EBS, is it still necessary to create the physical tables?

  His independent of any source. It comes to OBIEE modeling to create the RPD with all the layers. If you build from scratch, then you will need to create all layers else if BI Apps is used so you can get pre-built RPD and other pre-designed components.

  (3) if the physical creation of tables is needed, how to transfer data from the source of BSE BIEE physical tables tables? What ETL tool is preferred for most of developers? generator for warehouse or Oracle data integration?

  BI apps comes with ETL pre-built mapping to use with the tools majorly with Informatica. Only applications BI 7.9.5.2 comes with ODI, but oracle has the intention of having only ODI for any other versions.

  (4) during the data transfer phase, there are many many large data to transfer, how to keep the entire? for example, it must transfer 1 million lines of source to physical tables BIEE database, when 50% is completed, users try to open the POET report, they can see the new data of 50% on the reports? is there some transaction in phase control ETL?

  User will see still old data because its good enable Cache and serving it after each load.

  See http://www.oracle.com/us/solutions/ent-performance-bi/bi-applications-066544.html...
  and a lot more docs on google

  Hope this helps