A few questions after the downgrade of Win 7 on Satellite U940 - 11L
friend of mine bought the Toshiba Satellite U940 - 11L which had Windows 8 on it, due to some reasons that she wanted to have Windows 7 installed on it, which was pretty easy.
Trouble came with the installation of the Symantec touchpad, after installing the drivers, it worked for about 10-15 minutes but then it stopped working.
Tried to uninstall and install again but no luck, found a few discussions where it was suggested to remove all the devices, remove the battery and the power cord.
Press the power button for 15 seconds and then power back on but still not lucky (I wasn't in the restoration of the default settings of the Bios I did not any change it outside disabling secure boot and replacing UEFI CSM that was needed to run win 7 on it).
Tried about 4 different sources when it comes to the drivers but still does not work. I checked the Device Manager Dev but see no conflict, and it shows that the unit works fine but the problem persists. Please note that the drivers were specific to windows 7.
Please if you have any suggestions we would greatly appriciate it.
On another note, I'm not able to install the bluetooth it (HW ID shows as ACPI\TOS6205), I tried to install it several times but no luck because it always shows as unknown device in the dev Manager. The driver that I use is Bluetooth Filter Driver Package as info.
Also, the computer is slower than it was with Windows 8, I suspect the reason for this is the fact that the installation of win 7 I accidentally erased part of the hybrid drive SSD (the size was 11.2 GB if I remember correctly, yes silly me...). I wasn't looking for a while on the net to see if there is a way to fix it but no luck so far.
Thank you very much for your time and your suggestions!
With regard to the question of the touchpad.
To my knowledge, the touchpad should work even if the Synaptics touchpad driver has not been installed. Windows system contains own driver that control the touchpad and provide standard settings. Of course after installing the Synapatics driver, you should get a few more options and features more touchpad.
I recommend you to download the driver for the touchpad from Synaptics driver page and install it again: http://www.synaptics.com/resources/drivers
With regard to the problem of BT.
The laptop supports WLan Intel (Intel Wireless-N 2230) card that supports BT connectivity. Bt driver filter pack is ONLY necessary if you laptop would use an Atheros WLan card or Realtek WLan card. For the Intel WLan modules such package of filter is NOT necessary. To get BT to work, you must install the battery Toshiba BT!
I have a lot of problems with Vista. First it took me a week to install my printer WiFi. (sollution: install local lpt1 as the printer, change port properties en gives a location network (computer/printername).)
Last problem: vista give no right to copy my USB hd protable with xp files.
Finally, I lost all hope and want to go back to xp.
Is there anyone with experience in the installation of win xp on this laptop. And is it possible to tell me the steps that you have been taken to do so.
Are there concerns as none have some drivers, things that do not work or problems with sata hd.
It's a difficult topic-> XP on Vista machines.
First: Yes, you can install XP on it because all the important factors are available (VGA, SATA, wireless, XP BIOS, BLUETOOTH) and that should be enough.
Because your computer has a BIOS for Vista (I guess there a) Please install the BIOS XP first and then start the installation of XP. In the case that your HARD drive is not recognized then you need to install the SATA driver during the installation of windows XP. The procedure is described in the statement of the Satellite L40-> XP installation, so if you want to install and problems SATA (HDD, not during the XP installation), you must check the installation instructions for Windows XP for a SATELLITE L40!
If you have additional questions, I recommend allows you to place your question here before doing something that may stop your nerves later. :)
Use the drivers for W7 HP 2000z-2 has, except the wireless. Do not use any BIOS or the files of the firmware of this model on your.
I'm unable to download the update of the BIOS for a Toshiba Satellite Pro P300 PSPCDE (WIN 3.00), the reason being that I wonder a user name and password to download the file!
The laptop has this annoying problem to revive a few minutes after the laptop has stopped, and that's why I want to update the BIOS to see if it suits him. Laptop is running XP Pro (downgraded from Vista).
Ideas how I can get the update of the BIOS and will it solve the strange rebooting problem?
Where are you trying to download the BIOS?
I always download my updates on the official website of Toshiba and if it doesn't work maybe you should wait a day.
http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers
To be honest, I doubt that the BIOS update will solve this problem. I often read about this problem and you can solve if you disable the wake on LAN function in the BIOS and Windows (properties of the wireless network card).
I have a Toshiba Satellite A 100 - PSAANE with Vista Home Basic preinstalled in it.
Now, I have a few questions... I mention below: -.
(1) if I want to format my laptop, I need a CD to install for Vista Home basic... then I don't have this Toshiba CD when I bought the laptop. So how do? question: How can I format it?
(2) can I change my Vista Home Basic to windows XP? I think it's much faster than this one. is it advisable?
(3) I have a GB of RAM in the laptop. Increase the RAM? I think that my laptop has become to slow down. is it advisable?
(4) and on my screen, everytime I try to change my profile screen to windows Classic view, my screen begins to blink. and after a while, the screen turns off. So I can't change that. I put the color scheme of windows vista only. What to do about that?
Please help me friends. Thanks in advance.
Here, a few questions about the number:
(1) usually, you should get the Vista Toshiba Recovery DVD. If you didn t receive this DVD then you can order it here https://backupmedia.toshiba.eu/landing.aspx or you could install the disc of Microsoft Vista.
(2) of course, you can do this. I think that Win XP drivers can be downloaded from the Toshiba driver page.
(3) Yes, you can upgrade the RAM. For more information, see your manual or search on this forum for similar topics
(4) maybe it s associated with the graphics driver. Check if you can update. I would recommend additional check if you are using the latest version of the BIOS
Model: Toshiba L30-105 PSL33E-02S02HFR.
USB ports (2) do not work after the downgrade from vista to Windows xp family. All the drivers downloaded from Toshiba Web site.
Thanks for any help,
Have you installed Win XP all service packs?
SP2 provides some patches on the USB feature.
You definitely need to update the Win XP OS
I have the cliq, however I chose to not get 3G (so I bought full fare). So I have a few questions about the phone and the use of 3G / 2 G/Edge:
1 - is possible to disable completely the 2G / 3 G/Edge? I know you can switch between them, but are anyway just tell the phone to stop using them altogether since I'm not subbed to the service?
2. when the update takes place, I guess we'll have to reconnect motoblur and etc, but if I don't have 3 G will I have motoblur connection problems after the update? Or he keeps the latest wifi settings so that it would connect to wifi to connect. When I first got my phone it was not a problem b/c I had 3G for the first month.
I hope that makes sense, thanks!
To stop all the data, I would like to download an application called APNDroid. He cut them all down. When you log on to blur you have 3G or WIFI doe this without getting a timeout error. During the process of setting up your Blur account, you can press the menu button and set up your wifi to work, this will connect you to Blur and your phone will be connected to the blur. If I were you I would be rethinking to do a data plan since you are really losing out on most of your main features of phones. It's your choice, however.
I have a few questions about the Upgrade of Windows 8 offer for new computers. I recently bought a Toshiba Satellite S855-S5268 of amazon.com, which came with Windows 7 Home Premium. Toshiba already has a beta version of drivers and utilities for Windows 8 for the S855 on their Web site.(1) I bought my laptop in July of this year, and I've not yet registered for 8 Windows Upgrade offer with Microsoft. Am I still eligible to receive the upgrade, if I sign up soon?(2) if I buy the upgrade through this offer, I'll be able to download an ISO file so I can burn the installation media, or do I need to upgrade to Windows 7?(3) if I will be able to burn the installation media, I'll be able to erase my hard drive and do a clean install of Windows 8 (which I'd rather do, I have a lot of backups of my data). I am aware that I would probably need to provide my product key Windows 7 Home Premium 64-bit OEM during the new installation, because it is an upgrade and not a full version; This isn't a big deal, because my Windows 7 Home Premium 64-bit OEM product key is stuck at the bottom of my laptop.(4) my current copy of Windows 7 is activated by seeing my BIOS (I have a traditional BIOS, not a UEFI). If I had to switch to Windows 8 and decide then I'd rather back in Windows 7, for example, a few months later, I'll be able to do that (I burned recovery of Windows 7 with the Toshiba utility disks, which I did), and Windows 7 will continue to activate by seeing my BIOS, even after the installation (and later remove) Windows 8?Thank you very much!
I have a few questions about the Upgrade of Windows 8 offer for new computers. I recently bought a Toshiba Satellite S855-S5268 of amazon.com, which came with Windows 7 Home Premium. Toshiba already has a beta version of drivers and utilities for Windows 8 for the S855 on their Web site.(1) I bought my laptop in July of this year, and I've not yet registered for 8 Windows Upgrade offer with Microsoft. Am I still eligible to receive the upgrade, if I sign up soon?Yes, the registration period is between June 2, 2012 to January 31, 2013.(2) if I buy the upgrade through this offer, I'll be able to download an ISO file so I can burn the installation media, or do I need to upgrade to Windows 7?Yes, the Upgrade Wizard of Windows 8 will allow you to create a bootable DVD or you can grab the ESD file and save it.(3) if I will be able to burn the installation media, I'll be able to erase my hard drive and do a clean install of Windows 8 (which I'd rather do, I have a lot of backups of my data). I am aware that I would probably need to provide my product key Windows 7 Home Premium 64-bit OEM during the new installation, because it is an upgrade and not a full version; This isn't a big deal, because my Windows 7 Home Premium 64-bit OEM product key is stuck at the bottom of my laptop.Yes and there are better ways to reinstall Windows 8 without using the installation disc, you can use the reset and refresh.
These steps will take you through refreshing your PC:
· Press the Windows key + C on your keyboard to show the charms (if you use a touch screen: touch the right edge of your screen and drag your finger to the left)
· Click settings
· Click change PC settings
· Click general in the left column
· Under refresh your PC without affecting your files, click Start
Then follow the instructions that will be provided on-screen to cool your PC.(4) my current copy of Windows 7 is activated by seeing my BIOS (I have a traditional BIOS, not a UEFI). If I had to switch to Windows 8 and decide then I'd rather back in Windows 7, for example, a few months later, I'll be able to do that (I burned recovery of Windows 7 with the Toshiba utility disks, which I did), and Windows 7 will continue to activate by seeing my BIOS, even after the installation (and later remove) Windows 8?As long as you have a recovery disk which you should create or use the construction in the recovery partition, Yes, it will self activate.Thank you very much!
I have a few questions about the affiliation of creative cloud:
1. There is an Adobe offer up to 27.11. : the price offered is 47.59 euros per month including MWSt (VAT) or €568,20 / year.
2. after the period of the offer, the membership will cost the standard-price: €59,49 / month or €713,86 / year (seen on the Adobe Web site).
For how many years this standard - the price is fixed?
Is the standard-prices include MWSt. (VAT) too?
I advise you to contact Adobe sales for queries on pricing.
I now use ESX 5.1
I have a few questions about the VMmark test!
Disk space for VM is important?
Because I found the client model.
Space is limited, after that I installed the cygwin
I use Windows 2008, the default 32 GB is not enough
Same thing happened the day before VM
The default space is not enough after Windows Update
When we asked him to specify the size of the virtual disk and provisioning policy, enter either 15 GB (for you will be
using Windows Server 2003) or 32 GB (because you are using Windows Server 2008), let the floppy
For this configuration to disk, I have to choose one of the three methods, I can't uncheckd
Only that I should check?
Is there any document with pictures of installation to follow?
Thank you very much...
The script automatically uncomment all lines, as for example the kern.srv.cleanup_threads, cygserver.conf values 2.
In the files that you have shown, the values were already décommentés so there is no change. Your cygserver.conf is correct.
I have a few questions about the migration of the website and content (from development to test) which are not specified after reading the oracle documentation.
-> When we make the site replication will be migrated content (data files).
-> when we move will contained all the ED and RD etc (any object type web site migrated).
--> are the two the necessary step for migration when we migrate web site.
--> When we make the site replication of the content will be migrated (data files).
It depends on how you do it. The tool 'Site Studio Replicator' won't move any content, only the structure of the site. The 'Manage replication Site' page can be used to migrate content with the structure of the site but I do not recommend for large sites, I use separate tasks to archive to move the content. "Backup and restore" page stores the entire site in a ZIP file, not advisable for large sites.
--> When migrate us content will be all ED and RD etc (any object type web site migrated).
Yes. It uses the metadata xWebsites field to identify the elements that belong to the site.
--> are the two the necessary step for migration when we migrate web site.
Depends on how you do it, but yes, all bits are needed.
After the upgrade to WIN 8, have been uninstalled all of my programs, including Office 2010. Does anyone know if there is a way to get back programs without having to reinstall everything?
If you have selected "keep settings of Windows, files and applications, then you should still have Microsoft Office installed. You have not selected this option during installation?
Besides being able to keep your Windows settings and personal files, you can keep your personal files too during the upgrade to Windows 7. If you choose No, Windows 8 place your files in a folder named Windows.old.
If you have not selected these options, you will need to reinstall your programs since the original installation disc.
To launch your applications, go to the start, screen by pointing your mouse pointer on the left corner of the screen of Windows 8 and click on it.
Do scroll to the right and start your application.
For more information about how to install Windows 8 applications, see the following article:
I have a few questions on the Adobe CC Bill.
Now I use the new package 240 Baht/month, but on my Bill have a times.300 list 2 and 240 baht (detail in attachment)
Clouds please check and comment me.
Thank you for your kind support
Since this is an open forum, not Adobe support... you must contact Adobe personnel to help
Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">===>
Don't forget to stay signed with your Adobe ID before accessing the link below
Creative cloud support (all creative cloud customer service problems)
I have a few questions about the progress of the Actions (using the version of track CP7)
1. What is the function of the action to "continue?" Out of the peak action and advance the playback cursor?
2. What does mean this comment "Nested calls to action advanced is a nice improvement."? Is the advanced decision at the top of a page of action tabs?
3. What is the function of the option "custom" in the IF statement - "preform action if - custom", it doesn't seem to do anything for me?
4. where can I get information about the timeline / playhead interaction with advanced actions, i.e. where the playhead is going again at the beginning of the slide. slide custom question - display button, e.g. verification of responses, comments - when all the objects are at the beginning of the timeline. I'm looking more for the read head of infromation functionality rather than how to implement this type of question.
Continue: If an advanced standard action is triggered by a button, this will not trigger the playback head. If you want out, you can use continues. Continue can also be a choice in a conditional action, when one orders branching has nothing to special, but in advance. Continuous is also the "dummy" statement/command (this is the official name of a line in the dialog box advanced actions) If a statement has become unusable due to some reasons, it will be replaced by continue
There is no nested call stocks advanced possible right now, one of my many feature requests. It would be sort of a subroutine that you can use over and over again, instead of having to create each time when necessary.
A decision is one of the conditions to be an advanced conditional action. They allow to create more complex actions, as a loop or arrays are not possible. All decisions are executed in sequence and always.
Custom: is a combination of or but it is rather limited, because you cannot use parentheses.
I guess you'd better visit my blog if you want to learn more about the advanced actions.
I also did several Webinars on stocks advanced, last this afternoon (on the sharing of the actions) for Adobe. They are all available on request.
Greetings. I have a few questions regarding the audit.
1. how to enable auditing for create table and truncate table by a user?
Fact the knowledge of the above: http://psoug.org/reference/auditing.html
SQL> audit table by schema_name; Audit succeeded.
This succeeded. But when I actually created a table, it does not reflect in the dba_audit_trail;
Do I have to use the number of action by and then combine it with another table to populate the create table/truncate table?
2. How can I check what all auditing has been activated so far?
Please suggest me. I am unable to follow the audit to create and truncate.
In the above article that I mentioned earlier it said check the dba_audit_trail table.
COLUMN username FORMAT A10 COLUMN owner FORMAT A10 COLUMN obj_name FORMAT A10 COLUMN extended_timestamp FORMAT A35 SELECT username, extended_timestamp, owner, obj_name, action_name FROM dba_audit_trail WHERE owner = 'AUDIT_TEST' ORDER BY timestamp; USERNAME EXTENDED_TIMESTAMP OWNER OBJ_NAME ACTION_NAME ---------- ----------------------------------- ---------- ---------- ---------------------------- AUDIT_TEST 16-FEB-2006 14:16:55.435000 +00:00 AUDIT_TEST TEST_TAB CREATE TABLE AUDIT_TEST 16-FEB-2006 14:16:55.514000 +00:00 AUDIT_TEST TEST_TAB INSERT AUDIT_TEST 16-FEB-2006 14:16:55.545000 +00:00 AUDIT_TEST TEST_TAB UPDATE AUDIT_TEST 16-FEB-2006 14:16:55.592000 +00:00 AUDIT_TEST TEST_TAB SELECT AUDIT_TEST 16-FEB-2006 14:16:55.670000 +00:00 AUDIT_TEST TEST_TAB DELETE AUDIT_TEST 16-FEB-2006 14:17:00.045000 +00:00 AUDIT_TEST TEST_TAB DROP TABLE 6 rows selected. SQL>
Have you reviewed this table?
Alternatively, you can consult the table of dba_stmt_audit_opts.
Published by: Kerri_Robberts on July 15, 2011 15:11
Maybe you are looking for
I have a ze4610us. I don't use that plugged into the wall. Microsoft will cease support in April 2014. Given that I work for my home reception patterns and customer calls business on my laptop, I need to buy a new laptop with more memory and speed th
Every time I boot system, I get an error titled "Wireless Setup" window the window says "stored program isnot notification dll does not work correctly. Any ideas?
Recover my outlook folders of Windows 7, which disappeared when I empied the folder to delete
Note the title says it all. Do not remember using disk for initial instalation. Had to erase all the computers (laptop Hp 2000) for free from problems. It is once again - re-setup. Windows 7, installation. E-mail address is removed from the privac
files that are about 50 MB or more, can not be downloaded the integrity of my windows 7 Home premium for example, to install the Java SDK downloaded by my laptop, will appear a message a .cab file is corrupted, and I have to cancel the installation.