a VPN client is necessary?

Similar Questions

• All necessary licenses on ASA 5510 for old Cisco VPN Client

  We're trying to migrate our firewall Watchguard to a Cisco ASA 5510, who bought some time ago. For some reason, all of our users have already installed the old Cisco VPN client. I think it will work. Are there licensing issues on the 5510 I had to be concerned with?  No matter what special config that needs to be done on the 5510?

  Fix. You don't require licensing of AnyConnect of any type of configuration and the use of IKEv1 IPsec remote access VPN (which use the old Cisco VPN client).

  You will be limited to 250 active IPsec peers (remote access more no matter what VPN site-to-site) by the platform (hardware) device capabilities that are enforced by the software.

• SonicWALL NSA, using VPN client overall comments to reach network of internal resources

  Hello

  I have problems performing Global VPN client to work when you connect to our internal network of comments in order to reach our internal LAN Server in order to reach internal resources in a safe manner. I'm not sure what could the settings were necessary in the Sonicwall to achieve?

  Our installation is based on the NSA 3600 and I installed a WLAN area in the sonicwall to enable clients to connect to the internet. Traffic in the WLAN area to our internal LAN Server is denied. However, some users would like to be able to use the wireless network in order to achieve internal resources and for that I want to use the Global VPN client. It is even possible to use of an internal network from the point of view Sonicwalls Global VPN client?

  The use of the outside Global VPN client works very well

  Any help is greatly appreciated and if more detailed configuration information are necessary, I'll happily give you that.

  Thank you

  Hi Ben,

  No I didn't at first, but your answers have would lead me in the right direction, hopefully. I realized that I could create a custom GroupVPN by going to the settings of the interface to the interface that is the war in the Gulf to my wireless network.

  return to results

  Thank you

  Cree

• Cisco VPN Client cannot ping from LAN internal IP

  Hello

  I apologize in advance for my lack of knowledge about it, but I got a version of the software running ASA 5510 7.2 (2) and has been invited to set up a site with a client, I managed to get this configured and everything works fine. In addition, I created a group of tunnel ipsec-ra for users to connect to a particular server 192.168.10.100/24 remote, even if the connection is made successfully, I can not ping any IP on the LAN 192.168.10.0/24 located behind the ASA and when I ping inside the interface on the ASA it returns the public IP address of the external interface.

  If someone out there could give me a little push in the right direction, it would be much appreciated! This is the current configuration of the device.

  Thanks in advance.

  : Saved

  :

  ASA Version 7.2 (2)

  !

  hostname ciscoasa5510

  domain.local domain name

  activate the password. 123456789 / encrypted

  names of

  !

  interface Ethernet0/0

  nameif outside

  security-level 0

  PPPoE client vpdn group ISP

  12.34.56.789 255.255.255.255 IP address pppoe setroute

  !

  interface Ethernet0/1

  nameif inside

  security-level 100

  IP 192.168.10.1 255.255.255.0

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.1.1 255.255.255.0

  management only

  !

  passwd encrypted 123456789

  passive FTP mode

  clock timezone GMT/UTC 0

  summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00

  DNS server-group DefaultDNS

  domain.local domain name

  permit outside_20_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124

  permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 host 10.16.2.124

  access-list Split_Tunnel_List note the network of the company behind the ASA

  Split_Tunnel_List list standard access allowed 192.168.10.0 255.255.255.0

  pager lines 24

  asdm of logging of information

  Outside 1500 MTU

  Within 1500 MTU

  management of MTU 1500

  IP local pool domain_vpn_pool 192.168.11.1 - 192.168.11.254 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 522.bin

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Route outside 0.0.0.0 0.0.0.0 12.34.56.789 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  internal domain_vpn group policy

  attributes of the strategy of group domain_vpn

  value of 212.23.3.100 DNS server 212.23.6.100

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list Split_Tunnel_List

  username domain_ra_vpn password 123456789 encrypted

  username domain_ra_vpn attributes

  VPN-group-policy domain_vpn

  encrypted utilisateur.123456789 password username

  encrypted utilisateur.123456789 password username

  privilege of username user password encrypted passe.123456789 15

  encrypted utilisateur.123456789 password username

  the ssh LOCAL console AAA authentication

  AAA authentication enable LOCAL console

  Enable http server

  http 192.168.1.0 255.255.255.0 management

  http 192.168.10.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic outside_dyn_map 20 set pfs

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card crypto outside_map 20 match address outside_20_cryptomap

  peer set card crypto outside_map 20 987.65.43.21

  outside_map crypto 20 card value transform-set ESP-3DES-SHA

  3600 seconds, duration of life card crypto outside_map 20 set - the security association

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  aes-256 encryption

  sha hash

  Group 5

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  tunnel-group 987.65.43.21 type ipsec-l2l

  IPSec-attributes tunnel-group 987.65.43.21

  pre-shared-key *.

  tunnel-group domain_vpn type ipsec-ra

  tunnel-group domain_vpn General-attributes

  address domain_vpn_pool pool

  Group Policy - by default-domain_vpn

  domain_vpn group of tunnel ipsec-attributes

  pre-shared-key *.

  Telnet 192.168.10.0 255.255.255.0 inside

  Telnet timeout 5

  Console timeout 0

  VPDN group ISP request dialout pppoe

  VPDN group ISP localname [email protected] / * /

  VPDN group ISP ppp authentication chap

  VPDN username [email protected] / * / password *.

  dhcpd dns 212.23.3.100 212.23.6.100

  dhcpd lease 691200

  dhcpd ping_timeout 500

  domain.local domain dhcpd

  !

  dhcpd address 192.168.10.10 - 192.168.10.200 inside

  dhcpd allow inside

  !

  management of 192.168.1.2 - dhcpd address 192.168.1.254

  enable dhcpd management

  !

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum:1234567890987654321

  : end

  Hello

  Seems to me that you are atleast lack the NAT0 configuration for your VPN Client connection.

  This configuration is intended to allow the VPN Client to communicate with the local network with their original IP addresses. Although the main reason that this is necessary is to avoid this traffic to the normal rule of dynamic PAT passing this traffic and that traffic is falling for the corresponding time.

  You can add an ACL rule to the existing ACL NAT0, you have above and the NAT configuration should go next

  Add this

  permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0

  Hope this helps

  Let me know how it goes

  -Jouni

• The CBAC & VPN Client

  I use soft Cisco VPN client behind a Cisco CCCB router running. What are the ports must be opened to allow the client VPN working properly?

  I am currently using:

  allow an esp

  allow udp any any eq isakmp

  These are necessary, but you may also need to open UDP 10000 to support NAT - T if IPSec must cross a NAT border along its way.

  You'll also need allow beach access VPN client address to the IP address ranges whatever they are to be used in common. This is because packages through the ACL twice, once encrypted using ESP and ISAKMP, there not yet encrypted.

  So, if the VPN client has a range of pool to say 10.1.1.0/24 and his contact only the acl 10.2.0.0/16 subnet would look like:

  IP access-group extended VPNACCESS

  allow an esp

  allow udp any any eq isakmp

  permit IP 10.1.1.0 0.0.0.255 10.2.0.0 0.0.255.255

  Andy

• Cisco and Checkpoint VPN clients on a single PC

  Hello

  I'm in the following fix:

  I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.

  Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.

  According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.

  But I am not able to connect to my PIX, I receive the following error message:

  "Secure the complete VPN connection locally by the Client.

  Reason 403: failed to contact the security gateway. »

  When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.

  After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.

  After PC restart the Cisco VPN adapter is disabled later.

  I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).

  I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.

  After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.

  It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.

  Does anyone know of a workaround?

  Thank you

  Milan

  We had the same problem with some of our users who need to use the two clients to connect to customer sites.

  If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.

  We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

  After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.

  Hope that's a help

• VPN clients cannot access remote sites - PIX, routing problem?

  I have a problem with routing to remote from our company websites when users connect via their VPN client remotely (i.e. for home workers)

  Our headquarters contains a PIX 515E firewall. A number of remote sites to connect (via ADSL) to head office using IPSEC tunnels, ending the PIX.

  Behind the PIX is a router 7206 with connections to the seat of LANs and connections to a number of ISDN connected remote sites. The default route on 7206 points to the PIX from traffic firewall which sits to ADSL connected remote sites through the PIX. Internal traffic for LAN and ISDN connected sites is done via the 7206.

  Very good and works very well.

  When a user connects remotely using their VPN client (connection is interrupted on the PIX) so that they get an IP address from the pool configured on the PIX and they can access resources located on local networks to the office with no problems.

  However, the problem arises when a remote user wants access to a server located in one of the remote sites ADSL connected - it is impossible to access all these sites.

  On the remote site routers, I configured the access lists to allow access from the pool of IP addresses used by the PIX. But it made no difference. I think that the problem may be the routes configured on the PIX itself, but I don't know what is necessary to solve this problem.

  Does anyone have suggestions on what needs to be done to allow access to remote sites for users connected remotely via VPN?

  (Note: I suggested a workaround, users can use a server on LAN headquarters as a "jump point" to connect to remote servers from there)

  with pix v6, no traffic is allowed to redirect to the same interface.

  for example, a remote user initiates an rdp session for one of the barns adsl. PIX decrypts the packet coming from the external interface and looks at the destination. because the destination is one of adsl sites, pix will have to return traffic to the external interface. Unfortunately, pix v6.x has a limitation that would force the pix to drop the packet.

  with the v7, this restriction has been removed with the "same-security-traffic control intra-interface permits".

  http://www.Cisco.com/en/us/partner/products/HW/vpndevc/ps2030/products_configuration_example09186a008046f307.shtml

• Compression & CISCO VPN Client

  Hello

  I'm trying to understand if the compression is available using a 5.x CISCO VPN client to a device of CISCO (ASA, 871 etc..)

  Our site has recently moved from dial-in Windows, where compression is enabled, and we noticed the CISCO client show 'no compression '.

  Thank you

  Mario

  This URL describes how to configure the compression on the SAA.

  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/vpn_client500_501/administration/5vcAch3.html

  Compression can be configured as a parameter within the crypto ipsec transport-set in the IOS.

  http://www.Cisco.com/en/us/customer/docs/iOS/Security/command/reference/sec_c3.html#wp1057372

  Compression/decompression takes a toll hitting on the resources of the Cisco device if it lacks a hardware dedicated for these functions. You may want to limit its use to only where this is necessary for the remote access clients.

  HTH

• Windows - Internet access, no split Tunnel L2TP VPN Clients does not

  Greetings!

  I have four ASA 5505 that I configured with 4 site to site VPN tunnels (works perfectly) to connect to our company facilities 4. The ASA is also configured with remote access L2TP/IPsec so that a specific group of users of portable computers can connect to and access to all facilities. It also works very well except for one important exception - my split tunnel setting doesn't seem to work, because I can't connect to the Internet outside the VPN resources.

  I accept the inherent risk of allowing tunnels to split from a security point of view since I take the necessary steps to secure the systems used for remote access. I would appreciate any feedback on how to get the job of split tunnel.

  Here is the configuration:

  : Saved
  :
  ASA Version 1.0000 11
  !
  SGC hostname
  domain somewhere.com
  names of
  COMMENTS COMMENTS LAN 192.168.2.0 name description
  name 75.185.129.13 description of SGC - external INTERNAL ASA
  name 172.22.0.0 description of SITE1-LAN Ohio management network
  description of SITE2-LAN name 172.23.0.0 Lake Club Network
  name 172.24.0.0 description of training3-LAN network Southwood
  description of training3 - ASA 123.234.8.124 ASA Southwoods name
  INTERNAL name 192.168.10.0 network Local INTERNAL description
  description of name 192.168.11.0 INTERNAL - VPN VPN INTERNAL Clients
  description of Apollo name 192.168.10.4 INTERNAL domain controller
  description of DHD name 192.168.10.2 Access Point #1
  description of GDO name 192.168.10.3 Access Point #2
  description of Odyssey name 192.168.10.5 INTERNAL Test Server
  CMS internal description INTERNAL ASA name 192.168.10.1
  name 123.234.8.60 description of SITE1 - ASA ASA management Ohio
  description of SITE2 - ASA 123.234.8.189 Lake Club ASA name
  description of training3-VOICE name Southwood Voice Network 10.1.0.0
  name 172.25.0.0 description of training3-WIFI wireless Southwood
  !
  interface Vlan1
  nameif outside
  security-level 0
  IP address dhcp setroute
  !
  interface Vlan2
  nameif INSIDE
  security-level 100
  255.255.255.0 SGC-internal IP address
  !
  interface Vlan3
  nameif COMMENTS
  security-level 50
  IP 192.168.2.1 255.255.255.0
  !
  interface Ethernet0/0
  Time Warner Cable description
  !
  interface Ethernet0/1
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/2
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/3
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/4
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/5
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/6
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  interface Ethernet0/7
  Description for Wireless AP Trunk Port
  switchport access vlan 2
  switchport trunk allowed vlan 2-3
  switchport vlan trunk native 2
  switchport mode trunk
  !
  boot system Disk0: / asa821-11 - k8.bin
  Disk0: / config.txt boot configuration
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS domain-lookup outside
  INTERNAL DNS domain-lookup
  DNS domain-lookup GUEST
  DNS server-group DefaultDNS
  Name-Server 4.2.2.2
  domain somewhere.com
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  DM_INLINE_TCP_1 tcp service object-group
  EQ port 3389 object
  port-object eq www
  EQ object of the https port
  EQ smtp port object
  the DM_INLINE_NETWORK_1 object-group network
  network-object SITE1-LAN 255.255.0.0
  network-object SITE2-LAN 255.255.0.0
  network-object training3-LAN 255.255.0.0
  object-group training3-GLOBAL network
  Southwood description Global Network
  network-object training3-LAN 255.255.0.0
  network-object training3-VOICE 255.255.0.0
  network-object training3-WIFI 255.255.0.0
  DM_INLINE_TCP_2 tcp service object-group
  EQ port 5900 object
  EQ object Port 5901
  object-group network INTERNAL GLOBAL
  Description Global INTERNAL Network
  network-object INTERNAL 255.255.255.0
  network-object INTERNALLY-VPN 255.255.255.0
  access-list outside_access note Pings allow
  outside_access list extended access permit icmp any CMS-external host
  access-list outside_access note that VNC for Camille
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_2
  access-list outside_access note INTERNAL Services
  outside_access list extended access permit tcp any host CMS-external object-group DM_INLINE_TCP_1
  DefaultRAGroup_splitTunnelAcl list standard access allowed INTERNAL 255.255.255.0
  access-list sheep extended ip INTERNAL 255.255.255.0 allow INTERNAL VPN 255.255.255.0
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  access-list extended sheep allowed ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE1 extended permit ip IN-HOUSE-GLOBAL SITE1-LAN 255.255.0.0 object-group
  access-list INTERNAL-to-training3 extended permitted ip object-IN-HOUSE-GLOBAL object group training3-GLOBAL
  access-list INTERNAL-to-SITE2 extended permit ip IN-HOUSE-GLOBAL SITE2-LAN 255.255.0.0 object-group
  no pager
  Enable logging
  exploitation forest asdm warnings
  Debugging trace record
  Outside 1500 MTU
  MTU 1500 INTERNAL
  MTU 1500 COMMENTS
  192.168.11.1 mask - local 192.168.11.25 pool IN-HOUSE VPN IP 255.255.255.0
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 623.bin
  enable ASDM history
  ARP timeout 14400
  Global 1 interface (outside)
  (INTERNAL) NAT 0 access-list sheep
  NAT (INTERNAL) 1 0.0.0.0 0.0.0.0
  NAT (GUEST) 1 0.0.0.0 0.0.0.0
  5900 5900 Camille netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  3389 3389 Apollo netmask 255.255.255.255 interface static tcp (INDOOR, outdoor)
  public static tcp (INDOOR, outdoor) interface www Apollo www netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface https Apollo https netmask 255.255.255.255
  public static tcp (INDOOR, outdoor) interface smtp smtp Apollo netmask 255.255.255.255
  5901 puppy 5901 netmask 255.255.255.255 interface static tcp (GUEST, outdoor)
  Access-group outside_access in interface outside
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  RADIUS protocol AAA-server Apollo
  Apollo (INTERNAL) AAA-server Apollo
  Timeout 5
  key *.
  AAA authentication enable LOCAL console
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  Enable http server
  http 0.0.0.0 0.0.0.0 INTERNAL
  http 0.0.0.0 0.0.0.0 COMMENTS
  No snmp server location
  No snmp Server contact
  Community SNMP-server
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set transit mode TRANS_ESP_3DES_SHA
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-3DES-SHA TRANS_ESP_3DES_SHA
  correspondence address 1 card crypto outside_map INTERNAL SITE1
  card crypto outside_map 1 set of peer SITE1 - ASA
  card crypto outside_map 1 set of transformation-ESP-3DES-SHA
  address for correspondence card crypto outside_map 2 INTERNAL training3
  outside_map 2 peer training3 - ASA crypto card game
  card crypto outside_map 2 game of transformation-ESP-3DES-SHA
  address for correspondence outside_map 3 card crypto INTERNAL SITE2
  game card crypto outside_map 3 peers SITE2 - ASA
  card crypto outside_map 3 game of transformation-ESP-3DES-SHA
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  delimiter group @.
  Telnet training3 - ASA 255.255.255.255 outside
  Telnet SITE2 - ASA 255.255.255.255 outside
  Telnet SITE1 - ASA 255.255.255.255 outside
  Telnet 0.0.0.0 0.0.0.0 INTERNAL
  Telnet 0.0.0.0 0.0.0.0 COMMENTS
  Telnet timeout 60
  SSH enable ibou
  SSH training3 - ASA 255.255.255.255 outside
  SSH SITE2 - ASA 255.255.255.255 outside
  SSH SITE1 - ASA 255.255.255.255 outside
  SSH 0.0.0.0 0.0.0.0 INTERNAL
  SSH 0.0.0.0 0.0.0.0 COMMENTS
  SSH timeout 60
  Console timeout 0
  access to the INTERNAL administration
  Hello to tunnel L2TP 100
  interface ID client DHCP-client to the outside
  dhcpd dns 4.2.2.1 4.2.2.2
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  !
  address INTERNAL 192.168.10.100 dhcpd - 192.168.10.200
  dhcpd Apollo Odyssey interface INTERNAL dns
  dhcpd somewhere.com domain INTERNAL interface
  interface of dhcpd option 150 ip 10.1.1.40 INTERNAL
  enable dhcpd INTERNAL
  !
  dhcpd address 192.168.2.100 - 192.168.2.200 COMMENTS
  dhcpd dns 4.2.2.1 4.2.2.2 interface COMMENTS
  enable dhcpd COMMENTS
  !

  a basic threat threat detection
  statistical threat detection port
  Statistical threat detection Protocol
  Statistics-list of access threat detection
  a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
  NTP server 192.43.244.18 prefer external source
  WebVPN
  allow outside
  CSD image disk0:/securedesktop-asa-3.4.2048.pkg
  SVC disk0:/sslclient-win-1.1.4.179.pkg 1 image
  SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 2 image
  enable SVC
  Group Policy DefaultRAGroup INTERNAL
  attributes of Group Policy DefaultRAGroup
  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  Group Policy DefaultWEBVPNGroup INTERNAL
  attributes of Group Policy DefaultWEBVPNGroup
  VPN-tunnel-Protocol webvpn
  Group Policy DefaultL2LGroup INTERNAL
  attributes of Group Policy DefaultL2LGroup
  Protocol-tunnel-VPN IPSec l2tp ipsec
  Group Policy DefaultACVPNGroup INTERNAL
  attributes of Group Policy DefaultACVPNGroup
  VPN-tunnel-Protocol svc
  attributes of Group Policy DfltGrpPolicy
  value of 192.168.10.4 DNS Server 4.2.2.2
  VPN - 25 simultaneous connections
  VPN-idle-timeout no
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com
  the value INTERNAL VPN address pools
  chip-removal-disconnect disable card
  WebVPN
  SVC keepalive no
  client of dpd-interval SVC no
  dpd-interval SVC bridge no
  value of customization DfltCustomization
  attributes global-tunnel-group DefaultRAGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultRAGroup
  IPSec-attributes tunnel-group DefaultRAGroup
  pre-shared-key *.
  Disable ISAKMP keepalive
  tunnel-group DefaultRAGroup ppp-attributes
  No chap authentication
  no authentication ms-chap-v1
  ms-chap-v2 authentication
  attributes global-tunnel-group DefaultWEBVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultWEBVPNGroup
  tunnel-group 123.234.8.60 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.60
  pre-shared-key *.
  tunnel-group 123.234.8.124 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.124
  pre-shared-key *.
  tunnel-group 123.234.8.189 type ipsec-l2l
  IPSec-attributes tunnel-group 123.234.8.189
  pre-shared-key *.
  type tunnel-group DefaultACVPNGroup remote access
  attributes global-tunnel-group DefaultACVPNGroup
  VPN INTERNAL address pool
  Group Policy - by default-DefaultACVPNGroup
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the http
  inspect the they
  !
  global service-policy global_policy
  context of prompt hostname
  Cryptochecksum:423c807c0d63cb3e9aeceda977053f84
  : end
  ASDM image disk0: / asdm - 623.bin
  ASDM location Camille 255.255.255.255 INTERNAL
  ASDM location INTERNAL CGT-external 255.255.255.255
  ASDM location INTERNAL SITE1-LAN 255.255.0.0
  ASDM location INTERNAL SITE2-LAN 255.255.0.0
  ASDM location INTERNAL training3-LAN 255.255.0.0
  ASDM location INTERNAL training3 - ASA 255.255.255.255
  ASDM location INTERNAL GDO 255.255.255.255
  ASDM location INTERNAL SITE1 - ASA 255.255.255.255
  ASDM location INTERNAL SITE2 - ASA 255.255.255.255
  ASDM location INTERNAL training3-VOICE 255.255.0.0
  ASDM location puppy 255.255.255.255 INTERNAL
  enable ASDM history

  I should also mention that my test clients are a combination of Windows XP, Windows 7, and Windows Mobile. Other that in specifying the preshared key and forcing L2TP/IPsec on the client side, the VPN settings on clients are the default settings with the help of MS-CHAP/MS-CHAPv2.

  You must configure * intercept-dhcp enable * in your group strategy:

  attributes of Group Policy DefaultRAGroup

  attributes of Group Policy DefaultRAGroup

  Server DNS 192.168.10.4 value
  Protocol-tunnel-VPN l2tp ipsec
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl
  value by default-domain somewhere.com

  Intercept-dhcp enable

  -Latptop VPN clients (which I assume are on windows computers) is also the * use on remote network default gateway * box unchecked.  It is located on the Advanced tab of VPN client TCP/IP properties.   Select Client VPN > properties > Networking > TCP/IP Internet Protocol > properties > advanced and uncheck the box.

  Alex

• Configuration of Cisco for Cisco VPN Client ASA 5505

  Our firm has finally made the move from Sonicwall Cisco for our SMB customers. Got our first customer with a VPN site-to site solid and you have configured the main router for connections via the Cisco VPN Client VPN Wizard.

  When I install the VPN Client on desktop computers that does not capture all the necessary options (unless you have a SSL VPN). I guess that there is a process that I am missing to export a connection profile that Cisco VPN Client users can import for their connection.

  There step by step guides to create the connection profile file to distribute to customers?

  Hello

  The ASDM wizard is for the configuration on the SAA. This wizard will help you complete the VPN configuration on the end of the ASA.

  You will need to set the same in the client, so that they can negotiate and connect.

  Input connection in the client field, that's what you want to be seen that on the VPN client - it can be any name

  Host will be the external ip address of the ASA.

  Group options:

  name - same tunnel as defined on the ASA group
  Password - pre-shared as on ASA.

  Confirm password - same pre-shared key.

  Once this is over, you will see the customer having an entry same as a login entry. You must click on connect there. He will be a guest user and the password. Please enter the login crendentials. VPN connects.

  You can distribute the .pcf file that is formed at the place mentioned in the post above. Once the other client receive the .pcf, they need to import it by clicking this tab on the VPN client.

  Kind regards

  Anisha

• VPN clients are unable to access sites that are above a link from site to site

  could someone please give me some direction, I have a set of vpn clients set up on a pix and I'm trying to give them access to a network that is connected via a link from a site that is set up on the same pix. so, basically, that it receives information from VPN client on the same interface, it built the tunnel from site to site, I've heard that's not possible is that the case. Or it can be fixed, I can provide diagrams and if necessary conf files.

  You are right. You need a minimum of 7.0 for the feature you're looking for.

  Kind regards

  Arul

  * Please note all useful messages *.

• VPN client works well, but I am not able to open the desktop remotely

  Hi all

  I configured a router 877 with features of firewall and VPN and DDNS, when the user connects his WAN pc via VPN all works well (mail, telnet, ping, LAN access) but the Remote Desktop feature is not available. I traced with wireshark and saw that the request to port 3389 was correctly sent to the destination server, but the response to the VPN client has been abandoned by the router... and I have no idea how to solve this problem.

  Can someone help me...? Thank you very much.

  Ilaria.

  In room router attached.

  Your problem is the NAT-config. First of all, the next line is not necessary that RDP does not have UDP ober:

  IP nat inside source static udp 192.168.10.136 3389 3389 Dialer0 interface

  Then, the following command causes problems:

  IP nat inside source static tcp 192.168.10.136 3389 3389 Dialer0 interface

  With which the router assumes that the server 192.168.10.136 must always be reached through the IP address of dialer0 and made a translation.

  There are two ways to solve the problem, but they all have some disadvantages...

  (1) only access the server through VPN. For that you can just remove the NAT statement above (the one with tcp) and you should be able to reach the server via VPN.

  (2) restrict the NAT for not doing a translation if a VPN-peer's access to the server.

  To do this, you must attach a roadmap to the NAT statement. But who does not work with the "interface" - keyword in the NAT Statement. But you can use it if you get a fixed IP address from your provider.

  (3) assign a second IP address to the RDP server. The period of the original INVESTIGATION that is used in the NAT statement is used to access the server without VPN, the second IP address is used to access the server through VPN.

  --
  Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
  http://www.Kiva.org/invitedBy/karsteni

• Cannot access remote resources - Cisco VPN Client

  I'm having a problem with my Cisco VPN Client. I am new to VPN configuration, so this is probably something easy I'm missing. I have a my internet gateway for my LAN 2611XM router and my VPN server. I do all my tests of a society with a high card laptop mobile broadband. VPN connects, but anytime I ping anything in the network Cabinet, he returned with the public IP address of the external interface. I have NAT overload configured so any network can access the internet, inside which it looks like may be causing my problem. I don't know how to fix it. My config running is attatched. No one knows what might happen.

  Oh, almost forgot to add. When I remove the nat overload on my interface fa0/1, the vpn will connect to any resource on the inside.

  Your nat configuration seems to be the origin of the problem. If you are using an ACL to match the source for NAT, then it will be necessary to add the line 1A refuse for the local ip pool for your vpn clients to one only. try that to see how it goes.

  Sent by Cisco Support technique iPhone App

• Cisco VPN Client causes a blue screen crash on Windows XP Pro (Satellite M30)

  Hello

  I have a Satellite Pro M30 running Windows XP Professional.

  After you start a vpn Tunnel via a customer of Cisco VPN (Version 4.6 and 4.7), the system crashes with a blue screen.

  I see that the key exchange is successful, but immediately after the vpn connection is established Windows XP crashes with a blue screen.

  Someone has any idea how to solve this problem?

  Perhaps by the updated device driver? And if so, which driver should be updated?

  Kind regards

  Thorsten

  Hello

  Well, it seems that the Cisco client is a problem.
  I m unaware of this product because it of not designed by Toshiba.
  I think that the drivers are not compatible with the Windows operating system.
  However, I found this site troubleshooting cisco vpn client:
  Please check this:
  http://www.CITES.uiuc.edu/wireless/trouble-index.html

• R7000 vpn client.crt file is empty

  My version is 1.0.4.30_1.1.67.

  After you generate files of VPNs, client.crt file is empty 0 byte.

  The other files are correct.

  Can anyone help?

  Thank you.

  Hi @jli

  Welcome to the community!

  Try to use the latest beta of firmware 1.0.5.60.