A1410n on the motherboard heat sensors

Similar Questions

• HP G42 notebook: how to check the heat sensor

  my laptop fire but there is no system message...

  and performance down... could be heat sensor not properly detect...

  How to check the heat sensor...

  my laptop G-42-355tu

• HP Pavilion G6 2252so closing down due to the high heat (fan was cleaned up)

  I'm trying to fix a G6 model due to heat issues. The laptop is about 1 year. From what I have read on the internet, it is mainly due to the accumulation of dust. I told the owner that this was not covered by the warranty and offered to help with the cleaning of the fan. I completely cleaned the fan (incl. Remove the fan cover) and change the thermal paste on the processor. The problem persists. With the Speccy program, I read time of departure. for CPU to 90 degrees celsius. It's very different when the laptop shuts down. Sometimes it happends fast, at other times, he can run for hours. Even if the processor is completely cold, you can stop even before windows starts correctly. I managed to see the temperatures over 150 degrees celsius which should be alarming high. Even 90 degrees seems VERY high to me. The air blown by the fan seems not hot. It is only moderately hot and adjusts it fan speed according to the temperature. He begins to rise from more than 100 degrees. 90 to 99 degrees it runs pretty slow.

  If I try to go into the BIOS, I have only seconds before the closed laptop.

  From my point of view, he owes me two temperature sensors not working not properly, or the manipulation of temperature sensors is misinterperet, or simply the cooling system which is default. I don't know how the cooling system. The seat has a cobber lead wires for the heater and the fan. The tube contains a fluid? The liquid could somehow have vapourised?

  Be warm and helping the owner canceled its guarantee, now that I've had the dismantled oidissement?

  I tried to havn't updated the BIOS, because I'm afraid I'm going to brick the laptop, if it goes out during the process.

  Where is the temperature sensor placed on the Board? Is the sencot'en CPU built in or is it place in over/under it?

  How can I help the owner more far.

  Best regards

  Frank

  @FrankH82

  Hello again. I had actually read what you have written, but included these pages although I knew you did a large part of him he was already comprehensive, but also a reference to the point in case there was something on the picture in one of the documents that you may have missed, as a task to clean. I also realized that the BIOS update has been in the process as well, but guess you wouldn't do that, according to your previous statement, and that's understandable. I have not updated the BIOS, either when the PC has tendency to overheat and stop in the process (and brick it).

  In addition, there is the part about hardware failure analyses. From what you describe, it seems to me that the fan does not work as it should and is the likely source of the problem. If the unit is running too hot that you mention and the outgoing air flow is not so hot then there isn't enough air stream passes through. If instead it turns out to be a sensor problem, which is most likely going to require a replacement of the Commission.

  I have included the Service of Guide so that you can see how disassemble the unit safely if something had been missed in your household, and also, so you should have access to the parts list, if it turns out that the material is the source of the problem, since it includes the reference numbers for various sections that are replaceable by the customer including the fan and the heat sink (, motherboard, etc.) I have also included in part to answer your question on heat sensors that you request that are not listed as replaceable parts by the discreet.

  With respect to the copper pipes, they are units normally sealed with a small amount of distilled water inside at less than the normal pressure to reduce the boiling point of water, sort of way, it is meant to vaporize to help dissipate the heat. The only reason why the liquid inside would be gone is if the seal in the hose is damaged. If this is the case then it should be replaced.

  Now at this point, other than hardware problems as possible, as the system of cooling or the motherboard, which might need replacement, you can also look at the possibility of a cooling plate to increase the airflow. I myself for one of my laptops that I have left my son to use. He was very helpful while working in a warmer room in summer. It could be a quick thing to try so to make reliable unit until the likely hardware problem is resolved.

  Finally if you don't find that it is the material that needs to be replaced you should try calling the technical support to the 800-474-6836 line. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps.

• Pavilion p6-2310ea: radiator is not compatible with the motherboard

  I recently bought an AMD A10 5800 k for my PC and the radiator does not match my motherboard; the new radiator has clips and yet my original radiator has screws and it is not possible for me to install the clips.  I read that HP heat sinks are different to the normal heat sinks, can I put in my PC to make it possible for the heat sink to install? Where can I buy a radiator that is compatible with my motherboard?

  Hello

  The solution is that the old heatsink supports all the upgrades of the processor that are listed.

  Thanks for posting on the forum.

• HP pavilion dv7, share the same heat sink with the dv7 series?

  Hello

  I have a dv7 6c05ev and I am having trouble with the heat sink and I was wondering if I could change it by another?

  so I found a few things but I want a heatsink that is compatible with my motherboard is so other models of the dv7 series have the same heat sink with my model?
  Thank you in advance.

  George.

  No, no, no. It was probably 15-20/fan different devices used with the series dv7 over the years.

  You have a Core i5 - 2450M and the Radeon HD M 7470 video 1 GB dedicated then look at the owner's manual here:

  Manual

  Page 27

  For use only with the computer models equipped with an Intel processor and a graphics card
  subsystem with 1024 MB memory discreet 666390-001

  Reference 666390-001, and the part will agree and will work.

  HP charges $ 75 for him (ouch!):

  http://h20141.www2.HP.com/hpparts/Search_Results.aspx?mscssid=B22343D0B1B84F5CB4C3CCA1FF945CD1&SearchIn=PartNumber&SearchPN=666390-001

  A third of that on eBay:

  http://www.eBay.com/ITM/new-HP-Pavilion-650797-001-665309-001-666390-001-CPU-heatsink-cooling-fan-/171316580104?PT=US_CPU_Fans_Heatsinks&hash=item27e3438f08

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Change the motherboard & processor on the retail XP pro machine

  I will be able to change my case with my XP Pro retail license existing and mobo, cpu?

  I will be reusing the existing HARD disks and optical drives.

  Yes, but with a new motherboard if fails it "Repair Installation", you may need to perform a clean installation of XP.

  Still think XP has existed for some time it can't hurt to download the latest drivers from device XP and updated the BIOS from the web site of the manufacturer of the mother/support download card.

  Set of utilities to test for computer HARDWARE manufacturers:

  Note: If you are OverClocking or use any automatic overclocking BIOS features, Intel EIST or Turbo Mode (turn off).
  then back at the speed of stock as a starting point.

  Disconnect the other internal hard drives and external USB devices.

  First try running Memtest86 +, which runs from a floppy disk or CD and should eliminate or
  confirm whether your one or more of your sticks of memory are bad or the values of the SPD in the BIOS are correct.
  Let it run for as long as you can: 2,4,6,8 or several hours, so no errors at that time then your ram is OK.
  http://www.memtest.org/
  Memtest86 + Guide/How To (use the.) ISO to create a bootable CD)
  http://www.overclockers.com/forums/showthread.php?t=409152

  Hard drive test - CD Bootable:
  If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools (bootable CD) and check bad sectors:
  http://www.Seagate.com/WW/v/index.jsp?locale=en-us&name=SeaTools&vgnextoid=720bd20cacdec010VgnVCM100000dd04090aRCRD
  For Western Digital disks using WdDiag: http://support.wdc.com/product/download.asp?lang=en
  Fujitsu utilities: http://www.fujitsu.com/us/services/computing/storage/hdd/support/utilities.html
  Samsung Disk Manager software: http://www.samsung.com/Products/HardDiskDrive/utilities/shdiag.htm
  Hitachi Drive Fitness Test Software: http://www.hgst.com/hdd/support/download.htm#DFT

  Once Windows is installed:

  Device drivers: have you installed latest drivers from device of the manufacture of the motherboard? Visit their site to support for the latest drivers as the CD that came with the motherboard may have older less stable drivers.

  Check the download site of the manufacture of the graphics card for the newer Windows XP drivers for your card.
  See also the test of 'Smoke box' Nvidia or other demos: http://www.nvidia.com/object/cool_stuff.html#/demos
  or equivalent ATI.
  ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
  NVIDIA: http://www.nvidia.com/Download/index5.aspx?lang=en-us

  Prime 95:
  http://www.Mersenne.org/freesoft/
  It's a stand alone .exe file contained in an archive .zip.
  Simply choose to run the 'stress test' option for 3 hours or more.
  If your PC can pass this test, your memory and CPU
  are very good (close the housing cover in order to maintain adequate ventilation)

  Core Temp:
  The temperature of each core of the processor.
  For the overclockers using stock radiator and cooling fan Intel/AMD, you can expect a temperature range of
  35 to 40 ° C at idle and 60-65 c max when running Prime95.
  http://www.alcpu.com/CoreTemp/

  CPU ID (CPUZ):
  Watch the clock speed of the CPU under various conditions of loading
  (when using speed step technology Intel EIST).
  Also two tabs (memory and SPD) that shows the actual speed of the memory and 'SPD' tab displays the nominal speeds for each location of memory which is filled.
  Note: COMPARE the two values, the actual speed should not exceed the rated speed of your memory.
  http://www.CPUID.com/cpuz.php

  Test of Stress of FurMark GPU (graphics card):
  http://www.oZone3D.NET/benchmarks/fur/

  CPUID HWMonitor is a hardware monitoring program that reads health sensors main PC systems:
  voltages, temperatures, fans speed.
  http://www.CPUID.com/HWMonitor.php

  Pass marks burn in test: http://www.passmark.com/
  Burnin test, and their test bench at the same time give a good workout from all the major parts of Windows.

  HD Tune:
  Provides information of the car and has an option (tab scan error) to test your drive.
  http://www.hdtune.com/

  SpeedFan:
  Monitors internal temperatures and has a function of analysis health online (SMART tab) for hard disks drive.
  It displays your drives model number and compares your drive with other discs of the same brand and model.
  http://www.almico.com/SpeedFan.php

  GPU - Z:
  A utility light, designed for you give information about your video card and GPU.
  http://www.techpowerup.com/GPUZ/

  PC WIZARD:
  A powerful utility designed especially for detection of hardware, also analyses more.
  He is able to identify a large scale of system components and supports the latest technologies
  and standards.
  http://www.CPUID.com/pcwizard.php

  Partition Wizard Home Edition:
  (There is also a bootable CD version)
  http://www.partitionwizard.com/free-partition-manager.html
  Some of the features and functions include: resize and move partitions, Partition recovery after an accidental deletion, Create partition, Delete partition, format partition, convert partition, Explore, Hide partition partition.
  Change the drive letter, a partition active Set.
  Note: To complete any task use the "Pending Operations" box at the bottom left.

  Hiren BootCD
  http://www.Hiren.info/pages/Bootcd
  Hiren BootCD from USB (USB key)
  http://www.Hiren.info/pages/Bootcd-on-USB-disk
  (something more questions)

  UBCD4Win:
  http://www.UBCD4Win.com/index.htm
  UBCD4Win is a recovery CD bootable that contains software used for repairing,
  restoration or diagnose almost any computer problem.

  MyEventViewer - an easy way to display your event logs:
  http://www.NirSoft.NET/utils/my_event_viewer.html

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• The motherboard fan

  I swapped the motherboard for a Corsair SP120 fan in my office of CQ5300UK. It is a connector 3 pin identical to the oringinal, but I get an error of fan on the system startup. Why is this?

  The speed of the fan sensor has a minimum rotation value. Installation of a 120mm fan that has a slower speed causes this problem. An example of this can be found here:

  http://h30434.www3.HP.com/T5/desktop-hardware/system-fan-has-failed-error-after-case-swap/m-p/1404443#M46796

• Replace the motherboard only Windows 7

  My tale of woe: my wife and I love to play Poker Online and communicate with our children and grandchildren by e-mail and Skype.  However, it seems that because we bought a laptop Compaq CQ61 cheap Gray online auctions, we are now in a bit of a pickle.  We bought the laptop used with 12 months warranty from factory and it lasted 18 months only, in other words just out of warranty.  The laptop wouldn't turn on one morning and had a horrible smell of burning plastic, I myself am immediately turned it off.  Be retired we could not afford a new laptop, so I decided to have a look for me to see if I could do something.

  After a few hours of disassembly of the laptop, I discovered that there was an area on the motherboard that has been burned to a crisp.  Being somewhat handy I looked on ebay and to my surprise, I found an exact match for the motherboard to $160. Do not think of any other possible consequences, I ordered the M/B as the cheapest option.  About a week later the renovated Intel M/B happened and I went to transfer the old M/B to the new items.

  About a day later I pressed the button ON and to my amazement, he lit in windows 7.  This is where my problems started.  After a few starts, it displays all of a sudden in the bottom right of the screen:

  Windows 7
  Build 7601
  This copy of windows is not genuine

  As well as this occasionally at the start, he appears with the message saying "this copy of Windows is not genuine" and shows a screen trying to find a solution.

  I called the center of Activation Microsoft phone and told me that this copy of windows is linked to the M/B.  The M/B is the only bit that I replaced.  It has the same processor and the heat sink, has the same fan, he has the same drive, the same same chip memory 2 GB, it has the same wireless card but because the motherboard has been changed, now it's different.

  This sound like the old problem of axe. The handle has been changed seven times and the head was changed three times, but I know it's the same axe because I cut down a tree with her and it's the only one I have.

  The Microsoft representative said that if I had a windows recovery disk, he might have able to help me, but the only disc that was given to me with the laptop was a cardboard cut-out, explaining how to do a restore of Windows 7 and make a recovery disk.  He also said that I could simply ignore the message.

  The only other problems I have is that my HDD ATA internal and my CD/DVD drive now appear in devices and printers
  and as an icon to remove the device safely on my taskbar.  Research on the forum, this could be a problem of drivers.
  The only number on my laptop is Presario CQ61 on the front and Serial No. CNF9122FQP and a product no. NT350EA #ABU on the back on the tile and the lower part of the HP Support Assistant.  None of these numbers present on the HP site.

  Does anyone know what are my options, can I get a CD of windows 7 HP recovery, if so how? If I do get one then I'll be able to re-activare my copy of Windows 7.  If it sparkles on my only options would be to load a legitimate copy of Windows 2000 that I have or load Ubuntu 11.04, advice?

  Kenshep

  This produced many leads here:

  http://h10025.www1.HP.com/ewfrf/WC/product?product=3927381&CC=US&DLC=en&LC=en&Query=NT350EA&Tool=

  HP recovery disks will not work on a motherboard not original. Ubuntu may be your best choice if you can not afford the retail of Windows 7.

• The upgrade of the motherboard on DV6000

  I have a DV6000 with an Intel processor. I want to spend the motherboard, so I can install both a faster processor and a better graphics card. My question is... What is the best motherboard that I can install on this case? I don't mind to do a small modification to the case if one plank DV6500 series and above will fit, I would that the HDMI output. So overall, I need to know: the best advice for a DV6000, what change in case do I need to do, and what additional parts will I need for the new motherboard. I know I have to upgrade my fan and the heat sink.

  Thank you

  Now I got it. The card mother G72M is for an Intel processor with the dv6000 series nVidia graphics. The other 2, I think, use the integrated graphics card Intel. The G72M will perform better, but you risk running into default from nVidia that swept dv6000s and prompted a recall. If you can live with graphics performance Ho-hum I would receive the mother board 945 chipset, because as far as I know that those who have not caused any problems. Here is the motherboards used replacement HP for your model series. They represent the water drop in replacements except it may require some work miners dremel to breach to tell a firewire port which would not have been on your machine to the origin but which is on the replacement motherboard.

• Mac Book Air, failure of the motherboard

  Hi, I bought Mac Book Pro, a year and months back, yesterday, battery is down to 5%, so I continued to support, as I am studying end nyt I closed my MBA. Next day morning day when I tried to show him a folder with question mark symbol flashing. then I tried top in SafeMode it dint'showed hard drive. While I've taken at the authorized Service Center then they said his mother board failure and asked me to pay 42000INR. Is it really motherboard problem? What are the other options of best for me? and this is the price charged for the motherboard, even as they say? can I have any apple legal right againt for replacement?

  You can test it by connecting via USB, a boot disk.  If the Mac recognizes, the Mac, boots, then the internal drive or connection that is the problem.  Is it is not recognized, then it may very well be a logic card problem.

  Ciao.

• Pavilion HPE H9-1130: install the firewire card correctly into the slot of the motherboard correctly

  Hello, for my HP Pavilion HPE H9 1130, how to install the correct firewire in the motherboard slot card OK in OS Windows 10 x 64 / x 64 processor? And what video software system can I download to recognize my Panasonic 100a camera AX?

  Thank you. Followed your instructions. And it worked perfectly. Thank you. Even if I have Adobe Prem Pro, I downloaded MS Director and put 9 drivers after installing the PCIe card. Then it worked perfectly to capture video from a FireWire camera. Thank you once again!

• Bad video port, can I get an expansion card video or what I need to replace the motherboard?

  I have a Compaq SR2150NX, the monitor works on another PC, but will not be on this one, so I guess the video port is bad.

  Can I get a plug in video card and install it, or do I need to get the motherboard replaced?

  If I can get a video card, I can't know how to disable the frame on one, I need to disable or how I?

  My computer is a HP 5188-6734 motherboard and I can't find this one exactly, but I found a HP 5188-5588 one on e - bay for about $70, which seems to be and seems that I can tell, exactly like what I have.  Can I replace the one I have with this one without any problems?

  Looking for help.

  You are this posting in the wrong forum, this is a forum of the laptop and is a desktop system.

  Yes, you can get a video card, install and use it.  However, you sure is that the video works is not, or is it possible that the video didn't come out because you have a larger problem as the system's not initialization and display at all, because of a sort of failure such as food or the card mother?

  If you have a spare PSU, you can try exchanging it instead of the original.  If you have a spare video card, even a few old (especially some former) PCI worthless, that you can install to see if you get any screen output.  Note that you need to maybe use the CMOS clear jumper or remove the battery for 10 minutes, while the power supply is disconnected after adding a video card, or by deleting and trying to use the video again.

  I don't know if the specifications of the two Councils are quite similar, you should look at the datasheet for your system and compare that against what ebay sellers asking them is capable of.   Generally if you have a processor socket 775 lines they list and your using the same chipset, you should be able to simply plug in the parts and windows must be able to start pretty far to plug-and-play all the minor differences.  This is the situation in which I expected, you can buy the replacement cards model you mentioned and it works perfectly except possibly having to install a driver or two, but I can't be sure without detailed specifications.  They are very close to the info, I have found, might even be just a 2nd revision of the same Council of PCChips where everything what they changed was a clock IC generator or something similar that would not do your use in any way, except that to be sure, you have the good bios when looking on the HP site for the models with this Council in there instead of the bios for your system model #. If they take even a different bios which they cannot.

• Qosmio X 870 PSPLXA 00T00E - details of the motherboard

  I have WIndows 7 Home Premium 64 bit on this computer. I have trouble finding information about the motherboard for islet need to know if she will be able to handle the SATA III or has only been designed to SATAII. Also, what is the maximum size hard drive, this machine can handle?

  Thanks in advance for help :-)

  Hello, not long ago I bought an SSD for my qosmio X 870, AFAIK could manage only SATAII, but since most hard drives are SATAll / lll compatible, you need to check on this, "so-called" lll SATA retro-compatibility, I bought a Samsung Evo 850 with 500 GB and it works perfectly!
  In regards to the maximum, that I don't know, but at least 1 TB as the original drive.
  See you soon!

• Satalite Pro C650-18 t - how to access the motherboard?

  Hey,.

  I was pulling on my hair for the last 3 hours trying to find a way to get to the motherboard. I removed all good there, and still nothing. It doesn't seem to be a way to remove the bottom to access the motherboard.

  Can anyone help? Please?

  Hello

  Why you do this?
  I mean that the C650 is not an old book.
  The guarantee was valid and now the warranty is valid more because you have disassembled the unit

  Sorry mate I put t know how help you I want to say that there are a lot of screws and it is important to remove all the pieces in the right order
  I don't think that this is possible without having to disassemble everything manuals or instructions.

  I think that you should visit a laptop technician for assistance

• Want to 800-060: reactivation after replacing the motherboard

  I bought a HP Envy 800-060 with Windows 8 pre - install Amazon in July of 2013. It was an incredible computer since that time, and when the free update of Windows 8 for Windows 10, I did immediately released. Recently, however, the motherboard has failed on the computer. It would not stay same POSITION, and after much troubleshooting, I finally decided to replace the motherboard. Now that the computer is running again, I guess that the motherboard change was sufficient for the operating system to think that it is no longer enabled. I was never provided with a key of Activation of OS (Win8 has been pre-installed), and Microsoft has suggested that I contact HP to find the original key. I've looked everywhere on the chassis and inside the tower for a valid Windows activation key, nothing helps. I tried to find a phone number to call for support, but my product is outside the guarantee. I don't need advice or troubleshooting tips (so I don't pay the $59.99), all I need is my activation key valid Windows based on my serial number of the product. Anyone know the best way to achieve HP with this problem and have it is resolved?

  Thanks in advance!

  JC

  jcontino889

  The unfortunate, is that your original product key has been incorporated in the firmware original by HP motherboard UEFI when the PC was built.  There is no way to recover this key now.

  HP retains no record of keys to individualized product corresponding to individual computers, so they won't be able to provide you with the original key - and they are under no obligation to provide you with a SECOND key, that you didn't do the replacement of HP hardware.

  With the product now being out of warranty, it's really call HP or not you upload support - and the experience I have had with older equipment-, they do that, there's just no way around IDs.

  HP customer support is really the only way you have to get support.  If they don't help you for free, because your PC is out of warranty, there is nothing we can do about it on this forum.