A80: CD-ROM uses only PIO mode?
Hi, I have a laptop A80, properly up and running fine...
But if I try to burn a disc with Nero or Recordnow it often breaks down and the buffer to be missed...
I checked the IDE control settings:
the primary controller is very well and uses the Ultra DMA 5, but secondary to the cd-rom use only PIO although "DMA if available" is enabled!
is this normal? I did a bios update, but that did not help...
pls help me!
(Sorry for my bad English)
Hello
Well, as far as I know, that it should be possible to change these settings manually.
But I think s an operating system. I found on the Microsoft site info than after the Port IDE/ATAPI Windows driver (Atapi.sys) received a total of six time-out or cyclical redundancy (CRC) check errors, the pilot reduced the speed of communication (transfer mode) since the above basic mode (DMA, Direct Memory Access) to lower DMA modes in steps.
You should visit this site. I m you will find a solution for this problem.
http://support.Microsoft.com/?kbid=817472
Good bye
Tags: Toshiba
Similar Questions
-
CD and dvd only read some disks. Can read the disks using only safe mode
CD and dvd only play old discs. Cannot install new software. in safe mode may start to read and install the software however need internet to continue. Safemmode with networking won't read disc's
http://support.microsoft.com/fixit/default.aspx. It is new and fully automated Microsoft Portal. It is free and can help you solve more problems with just a few mouse clicks. TO BOOKMARK! "THE BEST THING TO DO IN THIS WORLD IS A WRONG ANSWER! "I"DON'T"WINDOWS...". »
-
Re: How to use Recovery Expert Mode in Satellite Pro M70-220 product recovery CD
I would appreciate advice on the following points.
My Satellite Pro M70-220 (PSM75E-00D008G3), portable computer has 4 partitions created by Acronis Disk Director costume v9:
C: OS - Win XP Pro SP3
D: programs
E: data & downloads
F: backupsAfter you start the laptop in Win XP, I inserted the recovery CD Toshiba in the DVD - RAM drive
and sailed to the BMP file, R:\G_INST\BMP, where I found the file "menu.bmp", which gives 2 recovery
Options:* 1. Retrieve entire hard drive *.
Caveat. All data stored o your computer will be lost.
Preinstalled software factory will be installed.* 2. Recovery expert Mode WARNING: *.
This is for PC experts only.
Preinstalled software factory can be installed on an existing partition.My questions are linked using the "Recovery Expert" Mode:
-I'll be able to use the "recovery of the Expert Mode' the recovery CD to reinstall Win XP Pro (pre-installed software factory) on my C: partition, while affecting only not partitions D, E & F?
-I'll be able to format the C: partition by using the "Expert recovery" Mode, without formatting of other partitions?
-What is the exact procedure of "Expert Recovery Mode"?
-where can I find more information on the procedure of "Expert Recovery Mode"?Thank you
AlanCB
> I'll be able to use the "recovery of the Expert Mode' the recovery CD to reinstall Win XP Pro (pre-installed software factory) on my C: partition, while affecting only not partitions D, E & F
Yes, this should be possible. Using the Expert Mode of recovery, you should get the ghost window where you can select the partition where the OS is to be installed. In this case only that partition would be formatted.
> will it be possible to format the C: partition by using the "Expert recovery" Mode, without formatting of other partitions?
Yes, theoretically it should be possible.
> what is the exact procedure of "Expert Mode of recovery"?
As I mentioned above, this mode allows you to restore the operating system on a partition of some and only this partition will be formatted.> where can I find more information on the procedure of "Expert Mode of recovery"?
What looking here in the forum?
I found this thread:
http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=7302ᲆ -
Firefox 5 displays the right fonts only in Mode safe!
After upgrading to Firefox 5, I noticed it displays the wrong fonts (larger than they should - they look ok in Firefox 4.x, Chrome, Opera).
The strange thing is that if I run Firefox 5 Mode without failure, it displays it correctly. I have disabled all addons, I cleaned all Cache, configuration of the size of minimum font... even reinstalled. It is allowed only in Mode safe looking.
What else to do?
Safe mode disables extensions in Firefox 4, and disables hardware acceleration.
- Tools > Options > advanced > General > Browsing: "use hardware acceleration when available.
Try to turn some of the prefs Boolean gfx.font_rendering on the topic: configuration page to disable some features.
Filter: gfxTo open the topic: config page, type Subject: config in the address bar (address) and press the 'Enter' key, as you type the url of a Web site to open a Web site.
If you see a warning then you can confirm that you want to access this page.
You can use the filter at the top bar of the on: page config to more easily spot a pref. -
HARD drive in PIO mode - very slow
Anyone else have a HD Sentinel message - or another HARD drive test, that HARD is only in PIO mode, not in Ultra DMA? It's really slow.
It can be verified, my computer - property - materials - IDE ATA/ATAPI - IDE elementary or secondary school - property - Special - if the watch - PIO transfer mode you have the same problem.
If Ultra DMA 1-5, you have no problem.If anyone has a solution, please report it. Thank you.
When the primary IDE controller is set to PIO mode, the audio may be distorted or the system can boot and run slowly. To resolve this issue, reinstall the primary IDE channel device driver. Primary IDE controller transfer mode will reset to default DMA.
-
Disabled IPad can be reset using the recovery mode
Someone with a good it knowledge doctored iPad without permission and now it can be reset using the recovery mode. While that plugged into iTunes, software downloads, iPad, then displays the Apple symbol but then returns the message "iPad is disabled connect to iTunes".
Hi stephen158,
I understand that, in the process of restoration of an iPad in recovery mode, your iPad rebooted and returns to the screen "connect to iTunes". This can occur if the software download takes longer than 15 minutes, how the iPad will exit Recovery mode and the software will continue to download. In this case, you should be able to put the iPad in recovery mode and choose to restore the device when prompted.
- Connect your device to your computer and open iTunes. If you don't have a computer, borrow one from a friend or go to an Apple Store or service provider authorized Apple for help.
- When your device is connected, force restart it: press and hold the sleep/wake and home for at least 10 seconds, and only release when you see the Apple logo. Keep until you see the screen in recovery mode now.
- When you see the option restore or update, choose update. iTunes will try to reinstall iOS without erasing your data. Please wait while iTunes downloaded the software for your device.
If the download takes more than 15 minutes the device out of recovery mode, you must repeat these steps and choose restore instead of update when you return to this step. - After the update or restore is complete, configure your device. If you have backed up your device with iTunes or iCloud and you need to restore your device in step 3, you may be able to restore from your backup during installation.
See you soon!
-
Satellite L300-01:00 - DVD in PIO mode, cannot activate DMA mode
Hello everyone,
Recently, I have a laptop Toshiba L300-01:00 and I have a little problem with the DVD-ROM drive. Maybe some of you can help me with their knowledge. So here's the problem:
The DVD runs very slow, I guess in the PIO mode. I can't switch to DMA mode because there is no options.On ' Device Manager / IDE ATA/ATAPI controllers ' options are a single - 'Intel(r) ICH9M-E/M SATA AHCI Controller' where you cannot activate DMA mode.
I have WinXP SP2, SATA and all the other drivers installed.
So my question is, how can I enable the DMA mode for the DVD player?
Thank you very much.
Hello
I have a laptop with installed U400 XP OS and I the primary IDE channel entry into the IDE ATA/ATAPI controllers.
Main channel that you can switch to the PIO or DMA is available in IE.
Now the question is; How do you install XP on your laptop?
Usually, the SATA mode must be set to AHCI in the BIOS, and you must include the SATA drivers to install Win XP on this laptop.Then a primary IDE channel should if poster in devices and the PIO or DMA settings manager should be there.
-
OfficeJet 4630: 4630 can print grayscale using only the black cartridge?
I have purchased a printer 4630 and want to use it like I did my old PSC1350 - using only the black cartridge for all printing. I can't find any setting of grey for the 4630 that will allow for this. With the 1350, the grayscale setting would prevent any color ink cartridges is used, an unnecessary expense for printing in black on white paper.
If there is no setting on the 4630 grey scale, can I be sure that black ink is used only for printing without color?
Hello @clif9710!
Thanks for posting on the HP Forums!Your printer Officejet 4630 should be able to print in gray scale and the options should be in the window of the printer printing preferences. I was able to locate a document regarding the changing settings in windows 7 print.
If you do not get the options to print in gray scale you will need to uninstall the HP software, including the old software, restart the computer and re-install the HP Officejet 4630 software again.
To uninstall the software HP click here: uninstall the HP software
To download the HP software, click here: driver and software Officejet 4630
Another good thing about the Officejet 4630 is that it allows to print mode single cartridge. cartridges for your printer built in print heads which means that it requires no 2 print cartridges. If you never use the Tricolor cartridge or you are planning on printing in black, you can remove the Tricolor cartridge, put the cap of the cartridge down and close the lid. The printer should now say "mode single cartridge printing. Once the printer is closed upwards, you can send your print job and it will print using only the black cartridge one!
Thanks again for posting on the forums of HP and post back and let me know how it goes!
-
How do I change computer to use only the black cartridge for print on PSC 950 h
I'm having a problem with my hp psc 950 printer - when I try to copy something it gives me an error to support code on enter to align cartridges-i do this and it is not always copy - how can I change the printer to use only black ink, the color cartridge is probably more good, I just changed black ink and I really don't need the color in my copies - all solutions would be greatly appreciated
Thank you
Hi yalulu,
I understand that you do not use the black cartridge only. I find the features page and the manual for the PSC 950 but did not find that I was looking for. I would suggest trying to use the printer in mode single cartridge, but I am not sure if the printer supports this feature, that's what I was looking for.
Try out both cartridges, then put in black only. If this does not work, the only other suggestion I have is to replace the color cartridge.
You can use the below document to troubleshoot color cartridge, select the document that best describes the issue, or take a look at the same time. You can find these useful.
I hope this helps to solve the problem you are experiencing.
-
card installation causes the only safe mode startup
After a driver to install my card from his Creative SB2 worked well. The day of juxtaposing it wouldn't work. Later, the only safe mode startup is cured by disconnecting the sound card. Could he have gone wrong or how do I get that back to work?
Hello
I suggest that you contact the manufacturer of the sound card. the sound card is may be defective. Contact support for sound blaster creative audigy 2 at the following link:
http://us.creative.com/contactus/techsup/welcome.asp?h=5
Hope this information is useful.
-
Cannot start with using F8 safe mode. Of alternatives please?
The PC will not start in Safe Mode; When you use F8, the only option available in the Boot menu is 'select the first boot device. I have the hard drive and click on "enter", but the PC then starts as usual. Can I run Safe Mode otherwise?
There are malicious software that recognizes the/SafeBoot switch in the boot.ini file, and if both are present (the/SafeBoot and malware), the system starts up again in any mode until you remove the file boot.ini with the switch/SafeBoot. Maybe this isn't the case here.
Some malware knows you try to use the Safe Mode to find and eliminate and he won't you find and eliminate and will detect the/SafeBoot switch. It will keep you from boot mode safe to fool you into thinking that you are using a Point of restoration., do a repair installation, or install your XP from scratch (neither of which is never necessary).
The symptom of this affliction is the following (which can be something else with similar symptoms):
Starting Windows...
Loading your personal settings...
Once your settings...
End the session...
Loading your personal settings...
Once your settings...
End the session...Just FYE (for your pleasure)... I used to love the switch/SafeBoot, but will never suggest or recommend again because sometimes you will have a bigger (but fixable) problem :)
Add the switch/SafeBoot can fix the symptom of the problem (now able to start safe mode), but will not fix the real problem, that of why F8 seems to be wrong or is misunderstood.
-
Windows Help explains how to use the character map to copy or drag special characters in Unicode-aware applications. In Vista, it was possible (but heavy) to insert special characters using the keyboard with the method known as Alt-plus, which has only first need to add EnableHexNumpad to the registry *.
y at - it an easier way to insert Unicode characters using only the keyboard newly available in Windows 7? Adds EnableHexNumpad to the still of registry required to use the Alt-Plus mode? Other tips to quickly characters insert Unicode in taking applications support Unicode?
* Register instructions: Add a new string [REG_SZ] named EnableHexNumpad and a value of 1 in HKEY_Current_User/Control Panel/Input Method
Have you tried UnicodeInput? It is a small program that allows you to enter Windows Unicode characters via the keyboard. Works with practically all the applications that I tested. I use it on Vista, so I can't guarantee it will work also on 7...
You can find it at http://www.fileformat.info/tool/unicodeinput/unicodeinput.zip .
Kind regards
-
OK, I have a game called Star Wars: Knights of the Old Republic. The game does not use more than 2 cores, the problem is when I start the game without going through the Task Manager and manually set its priority to 2 hearts my usual game show on my screen, it will be black so I have to run the Task Manager to force the game to close. So what I'm saying is that whenever I want to play the game or launch the application, I have to open the Task Manager, find the game or application, and then right-click to set the number of cores in the processor to use and sound really get some tires. I was wondering if there was a way to instruct your computer to use only 2 cores at the launch of this game. I have Window 7 Home Premium, 8 GB of RAM and a graphics card in Asus R9 280.
Some cpu overclocking tools have a basic framework of cpu, and you can make a profile for these games, which limits the number of cores. In the past I've used used AMD OC tool for this.
-If your cpu is Hyper-threading, try disabling Hyper-threading technology.
-J' saw a few messages about this game, but don't remember any specific game fixed and did not
heard of him having a problem with quad core cpu. I have no problem with a quad core cpu with AMD Phenom 965 or Intel 3570 KOTR.
It is installed without using any sort of compatibility settings. I'm surprised I didn't even
fixes, or patches. It seems to work without the CD, if you use the StarWars - KOTR.exe spot
of the LaunchKOTR.exe as well.
He has run correctly on GTX560ti, GTX770, HD7970 and Intel HD4000 chart, but I don't have
reminder if she had a little problem with running in a window with pilots earlier or not. Probably not as
the same happens when you use the Intel HD4000 graphics.
I just found (rediscovered?) that the game always starts in windowed mode
(there is no option of mode in the settings or .ini however), but if I change the resolution
It goes full screen in one of the other options 1280 x 1024 (there are three of what appear to be the same resolution and refresh speed settings).
When you use two Intel HD 4000 graphics the graphics settings are also not available.
[EDIT: my machine with the PhenomII965/GTX560ti doesn't have this problem of windowed mode.]
It is quite rare for games to have real issues with quad core cpu. Fallout 3 is the most recent
I met (Yes not nearly as old as KOTR), and it took a change in the configuration file
in order to limit to two hearts.
I also had a couple of games that are configured to run on a single core at the Phenom 965 CPU usage at the time.
I used the AMD OC tool to create a profile with all but a core disabled, for each of these games.
-I do not use a parameter core with any games ATM, but some games running on
my machine with Intel processor and 770 a short while back only works on atm HD4000 Intel
(Memory, they were OK with the HD7970, using the version of the driver 13.9 or 13.12?) ).
Games that only work with Intel HD graphics card on the machine with the GTX770, always works on my machine with a PhenomII 965 and GTX560ti. Go figure...
.
-
Our company just upgraded to SQL Server Management Studio 2012 and it has been very useful because I needed to use the percentile for the code I wrote. As a first step, the function did not work because I set the compatibility mode 110 level. After that I did, the function worked. However, now it does not work yet, and I get the same error:
The PERCENTILE_DISC function is not allowed in the current compatibility mode. It can only in mode 110 or higher.
I went to the properties of database section, then options and noticed that the compatibility mode has not changed, it is set to "SQL Server 2012 (110). I even used the following code to see if that would help at all even if the compatibility mode is already on this mode:
ALTER DATABASE Analytics SET COMPATIBILITY_LEVEL = 110
Someone already had this problem or knows if I need to change something in the properties of database for this function work? Is this just a bug in the new version?
Hello
I suggest you post this question in the SQL Server 2012 TechNet Forums: http://social.technet.microsoft.com/Forums/en-us/category/sqlserver
Thank you.
-
I'm trying to set up my system Windows 7 Ultimate 64 - bit up to use Windows XP mode.
original title: XP Mode? HOW?I'm trying to set up my system using Windows XP mode 7 Ultimate 64-bit.
I thought that since it was announced box WE the Win7software it would be IN the software! ... Funny that...
But it's not. So, I go to the page to DOWNLOAD the software.
I'm greeted by a series of necessary downloads until I can run XP mode.
I've read all 3 steps of the instructions and felt they were simple enough to not have to print.
Then I hit the 'step 2 - download windows XP mode' I'm greeted by a validation required DOWNLOAD.
Ok no problem. My windows 7 is bought in-store (newegg). No pirated software IN my house much less ON my computer. It IS the only authentic.
So I DOWNLOAD the program validation and the race (install?) it.
I saw nothing happen after I ran (installed)? He had no visual feedback that he had done a thing.
So I thought that maybe it runs automatically, so I tried to hit the button "step 3 - virtual pc DOWNLOAD.
Yet ONCE I am greeted with the same 'Windows required vaidation' pop up.
...' excuse me? I thought I had already jumped by THAT hoop...
Then I hit the button "step 4".
I try to run the stand-alone program but get a "update is not applicable to your computer" popup.I'm sure that my computer can run programs.
The construction is as follows:INTEL - PROCESSOR | CORE I7 2600K 3.4 G 8 M Ram
Motherboard - GIGABYTE | GA-Z68XP-UD4 Z68 R
RAM - 16 Gb G.SKILL F3-12800
Primary HD - CRUCIAL 256 G (SSD) (operating system is installed on this drive)
Hard drive - Western Digital 500 G
Video cards - 2 x EVGA GTX580 3 G of Ram
Sound card - HT | OMEGA | CLARO + R
Cooling of the processor - ANTEC | KUHLER H2O
DVD players - 2 x burners Lite on Blue Ray
Power - COOLER MASTER 1000w
OS - MS WIN 7 ULTIMATE FULL
Please... PLEASE tell me how to get this software and run it.
I have loads of programs that need it.BTW - this should be a real HOOT when I set up on my brothers computer. I built it in my house and it doesn't even have an internet connection instead.
First of all, make sure that your installation of Windows 7 Ultimate already activated:
Activate Windows 7 on this computer:
http://Windows.Microsoft.com/en-us/Windows7/activate-Windows-7-on-this-computerIf you use another browser other than Internet Explorer to post, try rather IE. You should also try to temporarily disable your Windows Firewall, it is known to cause some problems with validation.
How to install:
Make sure you download both Windows XP Mode and Windows Virtual PC (download this first and install first).
After installation of Windows Virtual PC, click Start, type: enable or disable windows features
Hi enter on your keyboard
Scroll down and make sure that Windows Virtual PC is checked
Click OK
Reboot if prompted
-------------
Proceed with the installation of Windows XP Mode.
------------
http://www.notebooks.com/2009/11/23/using-Windows-Virtual-PC-with-Windows-XP-mode/
------------
Windows XP Mode and Windows Virtual PC
http://www.Microsoft.com/Windows/Virtual-PC/default.aspx
Windows XP Mode now accessible to more than PC
Get started with Windows Virtual PC
http://www.Microsoft.com/Windows/Virtual-PC/get-started.aspx
Maybe you are looking for
-
How do I access iCloud on my MacBook?
I have a MacBook and an iPad, but I'm not really a keen user of iCloud. I'm selling my MacBook and for a certain time will use a PC my wife will buy until my next trip to the United States where Mac is more reasonable prices, then they are in the cou
-
Dial-up connections in Windows 8?
Hello I have a Lenovo turn... fantastic, but can't find demand for dial-up connections from lenovo and the latest version for windows 7 is not compatible with... Thank you
-
Satellite A200 PSAF6A - question of upgrading the Bios
I have a Satellite A200 PSAF6A and I am trying to upgrade the Bios as the current has a virus or something in it and I want to know how to do this with a floppy disk based BACK or how to make a boot disk for bios. Any help would be so appreciated tha
-
Hacked account - when is it even once?
My account was hijacked over the weekend. This morning, I changed the password. But my account is really safe now? My friends are flooding me messages, concerned about my account.
-
my mother has a xp computer. where can I get a copy of xp to extract a disc. because the old operating system is buggy?