AAA accounting in charge of the Windows 2008 network POLICY server log

Similar Questions

• How to remove a desk Goflex usb 3.0 on a Windows 2008 R2 Standard Server adapter and then plug another server save desk Goflex usb 3.0 adapter?

  I am an intern for a company and they asked me to pass their already plugged into the adapter of desk Goflex usb 3.0 backwards Server Office Goflex USB 3.0 adapter. They mentioned that I unplug before the one that is already attached to the Windows 2008 R2 Standard Server, I want to stop the automatic updates and cut it (I don't know if they mean turn off Office Goflex usb 3.0, a server adapter or updates).

  Then plug back up Server Office Goflex usb 3.0 adapter. When it is plugged in that they said to go back to the top.

  My main question is how to do it safely with ruin them anything? My second question is what are the steps to remove the device already plugged into the computer? My third question is, what are the steps to configure the server to the top device once I plug?

  They have done this before, I can tell because there are 2 dates on a note of sticky notes on the backup server. I know that the Goflex desktop adapter is not really a matter of Microsoft but I tried to contact Seagate and they told me to contact Microsoft.

  Thank you!

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Windows 2008 network load balancing

  I hope someone can help.

  I'm looking to start to test the Windows 2008 network load balancing. This will serve a webfarm. I went through various whitepapers, and forum messages but who have a few more questions:

  1. I get VMWare recommends multicast. Windows 2008 gives you two options, multicast and IGMP multicast. Seeing that I'm not an expert in network management, I'm a little nervous about the switched. Apparently to enable IGMP Snooping on your Cisco switches eliminate this? Is this true, if so you need install your cluster as IGMP Mulicast?

  2 do you need to have dedicated NICs for the NLB cluster, separate vSwitch etc.? If this is not the case, there will be interference with the existing production network?

  3 is a necessary static arp entry on your switch? All switches or just the farm goes where the ESX hosts are connected to?

  Some info would be appreciated.

  1 have not tested, but IGMP snooping is what caused problems before because the switch ports would not join the group correctly, so it is suitable to test whether the OS is ready to send packets.

  2. it is better to use separate vNIC to the virtual IP address of the NLB cluster

  3 static arp would be necessary if the IGMP snooping does not work for the switch ports that will be the virtual machine hosts that are part of the NLB cluster.

  -KjB

• Disabling RC4 encryption in the Windows 2008 SP2 Server

  Hello

  I just saw through the 2868725 Ko to disable the RC4.

  According to the article, we need to install the KB update, then we need to change the values of registry keys to disable the RC4.

  However, I could not find the download for the Windows 2008 SP2 server file in the download link

  https://support.Microsoft.com/en-us/KB/2868725

  Any suggestion how to disable the RC4 in Windows 2008 SP2.

  Need help.

  Thanks in advance.

  Here is the link for the Microsoft TechNet forum:
  http://social.technet.Microsoft.com/forums/en-us/home?Forum=w7itpronetworking

  Several related to the server forum (not for Desktop/Win7)https://social.technet.microsoft.com/Forums/windowsserver/en-us/home?category=windowsserver

• The print queue status is displayed as "offline" on a Windows 2008 R2 Print Server.

  The fix in this article KB http://support.microsoft.com/kb/946198/ corrects this problem for windows 2003 SP2 print server.  The same exact symptom occurred in my windows 2008 r2 print server.  Is anyone is aware of the fix for the version of windows 2008 R2?

  It is a Forum of Vista.  For more information on servers, please repost the following:http://www.microsoft.com/communities/newsgroups/en-us/default.aspx?dg=microsoft.public.windows.server.general&cat=en_US_9741c575-ec92-42f8-85ba-00dfe1483cf5&lang=en&cr=US where Server experts will be happy to help you.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• My computer is connected to the Windows 2008 R2 server and some of the users on this computer receive their network drive mapped on group policy and some do not.

  My computer is connected to the Windows 2008 R2 server and some of the users on this computer receive their network drive mapped on group policy and some do not.  I find nothing in Event Viewer that shows that there is a problem.  Please let me know what to do to get the disks appears

  Original title: Network Networking file sharing file sharing file sharing file sharing discovery sharing Fileshare share shared

  Hi,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

   

  Hope this information helps.

• Impossible connecting to "fix it online." "Signins other Live" are OK - get the message "the Windows Live network is not available on this site.

  Get the message "the Windows Live network is unavailable on this site".

  Hello

  The question you have posted is related to windows live and would be better suited to the community of windows live. Please visit the link below to find a community that will provide the support you want.
  http://windowslivehelp.com/

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• How to make the Windows 7 network icon to show availability of internet connection? With flashing.

  How to make the Windows 7 network icon to show availability of internet connection?

  Flashing

  Hi RaDiCal007,

  Microsoft has removed the option host connection icon network; apparently drain you resources. Like you, I prefer much the icon 'flashing '.

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: www.winuser.co.uk | vistasupport.mvps.org | xphelpandsupport.mvps.org | www.silversurfer-Guide.com

• How to make the Windows 7 network icon to show availability of internet connection?

  Hello!
  Windows 7 network icon shows no availability of internet connection. Windows Vista network icon showed availability of internet connection with a globe. How to make the Windows 7 network icon to show availability of internet connection?
  Concerning

  Hello kopn,.

  Thank you for visiting the Microsoft answers community.

  The icon for your internet connection, but the animation and the color associated with the network icon in Vista and earlier versions is no design in Windows 7.
  Chris.H
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Manager Update 4 will not scan or clean up the Windows 2008 R2 server

  I just install a Windows 2008 R2 server, and Update Manager will not analyze it.  It just says: "Failed to scan or clean up SERVERNAME because of operating system not supported or unknown.  I can scan and clean up my plain Windows 2008 servers very well.  R2 is still not supported?

  I do not remember R2 being in the list of supported operating systems, I believe that this is also the case for the 4.0u1 VUM or VUM 4.0u1.1

  You'll probably want to make sure that the release notes, but if the error message says that it is not taken in charge, probably only is not supported.

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  VMware developer community

  If you find this information useful, please give points to "correct" or "useful".

• How to enable the Windows 2008 R2 guest operating systems on Windows 2008 R2 Datacenter edition host

  Sorry, I realize it is there much written and blogged about activation and license but I still cannot grasp exactly what to do, please can you help me.

  I have a host running windows 2008 R2, datacenter edition.  The 2008 datacenter edition license allows any number of windows OS to run on this host (will run for most 2008R3 standard edition) so I guess (I hope correctly) that I don't need to buy more licenses.

  So my question is, when these comments of the virtual machines are created, how can I activate them?  What product key should be used?   I have a product key for data center edition, but it does not work "the product key you entered will not work with this edition of windows server 2008 R2.

  Thank you if you can let me know if there is a way (or ways) for the operating systems Windows Server activated running on datacenter edition.

  Best regards

  Jules

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Hidden not displayed in the window 2008 R2

  In the window Server R2 I have 40 GB partition this partition usage is up to 25 GB now the point is while I select all the files hidden and consulted and indicated his total record size 17 GB. I unchecked all option hidden the folder option but I couldn't rectify 7 GB of files where it is? Help, please

  Hi arshkumaR,

  Thanks for posting in the Microsoft Community.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

• Group Policy does not apply on Windows 7 with the Windows 2008 R2 domain controller

  Trying to troubleshoot a GP associated question where, seems, desktops (Win 7 Enterpise) do not receive the last group policy.  He doesn't seem to get at some point after an arbitrary time period (two or three weeks), but it is insanse.

  -Have you checked with the GPMC (connect to each domain controller individually) that all four domain controllers are running the same GP later version; no replication errors.

  -No errors appear on the workstation or server logs (logs\winlogon or event viewer-> Group Policy).

  -gpupdate/force runs without error

  -gpresult and RSoP both supplement fine, watch the GP is be applied correctly, to APPLY THE OLD GP SO!

  -No error up with whent the following undocumented debugging is also enabled: [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Diagnostics] "GPSvcDebugLevel" = dword:00030002

  So, my little finger tells me that the problem is the GP are not be tire/replicated/either at the workplace in a timely mannger (reboot, gpupdate/force, etc.) but do not know how to see what is the interval, troubleshoot, etc.

  The server gurus hang out more in the TechNet forums.  This forum deals with questions of security of user, your question would be a better fit in the server instances:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Remove the path of the windows 2008 64-bit Oracle client

  Hi all

  I had to unstall the product of Hyperion epm after I found the installation have to done on another language, that has the oracle for 32 and 64-bit client. But when I reinstall it complains the way at oracle.

  Here is the error I get from the newspaper.

  [FATAL] [INS-32053] The original name of the Oracle Home specified directory already exists.

  CAUSE: The name of the base directory Oracle Home specified on the command line matches an existing Oracle Home directory name in the central inventory.

  ACTION: Choose a different name for the Oracle Home Directory. Renoncer give to this setup session, and then try again.

  I made sure that the file system is completely is deleted after the unstallation except these client files which I deleted manually.

  It seems that the unnstalation does not correctly for clients and old path is somewhere still exists. I deleted the path in the environment variable path list customer and tried again but no luck.

  Can someone help me identify the places where I should look to remove Oracle's previous home.

  Thank you

  The register, perhaps, or the inventory (which is in c:\program files\oracle or c:\program files (x 86) \oracle - I don't remember right now).

  However, if you search for 'clean up the windows machine' Support of Oracle, you can find an article that shows you how to remove all traces of the Oracle software from your Windows computer.

• Can I move datadrives from a Windows 2003 server to a windows 2008 R2 enterprise server? Both servers are edge power Dell T610

  We are migrating Server 2003 to 2008 R2, Enterprise Edition.  I have the OS loaded and ready. However, the Server 2003 has almost a 1 TB of data, that I just wanted to know if I can get the readers in the new server and everything would be ok. If readers present themselves as foreign, it can be fixed, but I'm worried how 2008 will see readers.

  Thanks in advance.

  Jeff L.

  Support is located in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/