Access denied when accessing hard drive error.

Similar Questions

• We get an error "D: / is not accessible." a device i/o error"when trying to access hard drive

  * Original title: e/s problem

  I am not able to access my hard disk.windows that says: -.

  "D: / is not accessible." an i/o device error. "

  I also tried chkdsk but it says that it is not directly operatable.

  Hi Rishanpc,

  Thanks for the post. I am sorry to hear that you found a mistake "D: / is not accessible." a device i/o error"when trying to access hard drive.

  I imagine the inconvenience that you are experiencing. I will definitely help you with this.

   

   

  To help you suggest several steps to solve the problem, I would appreciate it if you could answer the following questions:

  1. have you checked if the cables are connected properly?

  2 what is an internal hard drive or external?

  3 have there been recent changes made on the computer before the show?

   

  The most common cause of a non-accessible i/o error is a disconnected cable. When the computer tries to access a device, and it's no response after several tests, it will generate this error. Another common cause is when a program tries to access a file that has been removed or eliminated.

   

  Disconnected Hard Drive/cable misconfiguration

   

  Internal hard drives require a specific set up. IDE hard disks can have only one master. If another hard drive has its defining together correctly pin code, a user is perhaps not able to access the data, and he will receive a message that the drive are not available. Cables come off inside the case of the computer also cause a not accessible i/o error. The user can correct this problem by opening the case and attach the data cables for each drive safely at the back of each drive and the motherboard.

   

  You can follow the steps below and check if it helps.

   

   

   

  a. go to "Control Panel" in the start menu and choose 'performance and Maintenance '.

  b. click on 'System' then go to the Hardware tab and click on "Device Manager."

  c. find the device that records an error by developing the appropriate category nodes. If the device has a red "X" on the icon beside its description, the hardware is disabled; Go to step d to activate it. Otherwise, go to step e.

  d. go to the general tab and click on "Activate the device" found in the device status section. then press 'OK '. (Note: you may need to follow the guests, as indicated via an assistant of favorable device.) If you do, continue to click "Next" and follow the instructions until the process is complete.) Test the equipment. If an error is displayed, go to step e.

  e. click the general tab and click "Troubleshooting" found in the device status section and then press 'OK '. Follow the prompts to fix the problem. If an error is still displayed, go to step f.

  f. click the driver tab and click on 'Update driver'. Follow the instructions until the process is complete and then to test the equipment.

   

   

   

  Your response is very important for us to ensure a proper resolution. Please get back to us with the information above to help you accordingly.

• Laptop HP 2000: hard drive error

  Hello
  I have upgraded to Windows 10 one a few days ago and then yesterday when I went to turn on my computer it says this.

  Hard drive error
  Please run the hard drive Test in the diagnostic system
  Hard disk 3 (3F1)

  I ran the test drive and that's what he said

  Smart check: PAST
  DST short: FAILURE

  Help, please!

  You will need to replace the hard drive. Update to Windows 10 had nothing to do with it. After the back if you want to help find a car and its installation and reinstallation of Windows. If your Windows 10 appeared as it is activated, you can do a clean reinstall of Windows 10.

• Start up and boot problem. Hard drive error. HP pavilion laptop Home Premium. Windows Vista preinstalled. No cd came with it.

  Nothing new added to comp. Got the hard drive error message and followed the instructions to fix/repair. All translations tried (almost every test suggested/memory/hard drive, etc.) could find NO problem with the memory or hard drive.  Once I have pass the problem to boot/start the computer works fine!   Crazy!  Any sugg. would be appreciated.

  Hello

  ·        Since when are you facing this problem?

  ·        What are the fix and repair that you tried to solve this problem?

  ·        Outside this disk verification error, do you get any other error message?

  Method 1:

  I suggest you to do a scan of the SFC. File system (CFS) Auditor verifies that all Windows 7 system files are where they should be as they are by default and not corrupted, changed or damaged.

  ·        Click Start, click principally made programs, accessories, right-click on command prompt and select run as administrator.

  ·        Click on continue or provide administrator credentials if prompted.

  ·        In the command prompt window, type the following text, and then press ENTER:

  ·        sfc/scannow

  ·        You should see the following message on the screen:

  § Begin the analysis of the system. This process will take time.

  § Beginning verification phase of system scan.

  ·        % Of verification complete.

  ·        Once the scan is complete, a test to see if the problem you are experiencing is resolved or not.

  For more information, see the article mentioned below.

  http://support.Microsoft.com/kb/929833

   

  Method 2:

  I suggest you to set Chkdsk to run when the system restarts the next time. Follow the steps mentioned below to set Chkdsk to run when Windows Vista reboots the next time.

  a. click on start, then run.

  b. in open, type cmd, and then press ENTER.

  c. use one of the following procedures:

  Procedure 1: To run Chkdsk in read-only, at the command prompt, type chkdsk, and then press ENTER.

  Procedure 2: To repair errors without scanning the volume for bad sectors, at the command prompt, type chkdsk volume: / f, and then press ENTER.

  Procedure 1: To run Chkdsk in read-only, at the command prompt, type chkdsk, and then press ENTER.

  Note: If one or more files on the hard disk are open, you will receive the following message is displayed:

  a. Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts? (Y/N)

  b. Type O, and then press ENTER to schedule the disk check, and then restart your computer to start the disk check.

  Procedure 2: To repair errors, locate bad sectors and recover readable information, at the command prompt, type chkdsk volume: / r, and then press ENTER.

  Note: If one or more files on the hard disk are open, you will receive the following message is displayed:

  a. Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts? (Y/N)

  b. Type O, and then press ENTER to schedule the disk check, and then restart your computer to start the disk check.

  You can see the article mentioned below for assistance.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Method 3:

  I suggest you to do a system restore. Follow the steps mentioned in the article below.

  What is system restore?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Hard drive error, but passes diagnostic

  I have a vostro 320 all in one computer. Yesterday he left initializing with a hard drive error, but when I run the hardware diagnostics all past. When I go into the installer the Bious does not see the hard drive. Current Bious is 1.2.0 and current is 1.4.0.

  If the BIOS does not see the hard drive, no - you will need to replace the disk.

  You can take a chance on the resettlement of the player (unplug the system and disconnect and reconnect the hard drive), but if so, it is not detected by the system, it is toast and needs to be replaced.

• hard drive error message 1

  Whenever I turn on my laptop, a message appears that there is a problem with my hard drive.  I have prees F2 to get the Diagnostics utility and run the hard drive test. When I do I get this message

  hard drive error

  Failure ID: 90 c 633-6am70r-mfgk0k - 60 c 203

  Product ID: c2n26ua #aba

  Hello

  Error code 24 characters will be a Smart failure or disk Self Test - in both cases, this would indicate that hard is defective and must be replaced.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• Dell Hard Drive Diagnostics fix hard drive errors

  My computer would stop working and say that I had a software problem.

  When restarting it would run for about 15 minutes and the cessation of work and

  show the same error.

  I have run the Dell diagnostic program and it showed that I have several

  Hard drive errors.

  After the diagnosis my computer now works fine.

  The diagnostic programs to correct the mistakes of hard dirve when he finds them.

  My computer is a Dimension 4700 running windows XP Professional

  Service Pack 3

  
  

• Satellite L350 - persistent master hard drive errors

  I've known persistent main hard disk errors. Errors, in their first incarnation, were windows freeze at loading screens and screensavers, and then developed by stopping Windows to boot at all. It certainly would not start normally and sometimes would not start in safe mode. I used the recovery partition to restore the computer to its factory settings. A day or two later, the same symptoms began to manifest again, although not as severely. The hard drive errors, freeze on screens and loading screen savers.

  My question is: if I re - format the hard drive master, thus destroying the recovery partition, I could then just restore windows from a newly formed recovery CD? And, in addition, what is the probability that reformatting the drive hard completely would have an effect on the frequency of errors?
  If the hard drive is simply borked, format or not? And if yes, what is the next step?
  Could I restore windows on my drive hard slave and give up on the master?

  Thanks in advance.
  Mike

  Hey Buddy,

  Are you sure that all these problems related to the HARD drive at 100%? How did you check that?

  I don t mean it s not the HARD drive, theoretically, you could be right but before you think to change the HARD drive please use a diagnostic tool special for HDD as Drive Fitness Test:
  http://www.HitachiGST.com/support/downloads/#DFT

  This tool can check your HARD drive for bad sectors.

  If the HARD features of bad sectors disk, formatting will not help you because the sectors are physically damaged. With other words, the only chance is to exchange it.

  But if you have already used the recovery feature of HARD Toshiba drive to reinstall Windows you can say s that no problem of software and it must be hardware related. ;)

• Hard drive error, does not start.

  Computer does not start. I get this failure code:
  Rw1xtw-7ax87b-mfpv6k-619403
  
  Can't find any information on this subject, can someone shed some light on this subject for me?

  Hello

  It decodes for hard drive error 305 or the hard drive has failed, you will need to get the replaced hard drive and reinstall the OS and have a Fresh start, note that all your data is saved on the hard drive will be lost.

• Blue screen error CANNOT ACCESS HARD DRIVE SPACE

  I'm trying to install windows xp after removing windows 8 of my computer and creat new partition using the boot disk windows 98se, fdisk, but the installation during windows startup I get in trouble when get a blue error message screen telling
  "YOUR COMPUTER'S STARTUP PROGRAM CANNOT ACCESS THE DISK THAT CONTAINS THE PARTITION FREE SPACE, YOU CHOOSE. CANNOT INSTALL WINDOWS XP ON THIS HARD DRIVE. »
  Image of the screen available message if necessary. There is no error due to this error code.
  Please help me to solve the problem, and I'll be really thankful to you.
  Kind regards
  Kay

  First of all, you need not use a setup of Windows 98 to work partition disk before installing Windows XP, Setup of Windows XP has the tools to do this job.

  Windows XP Setup cannot see the hard drive as it doesn't have drivers for the SATA controller on board.  To install Windows XP you must go into the BIOS and put the hard drive in IDE mode you will need to integrate the SATA drivers in the XP installation CD, or you need to feed them to the Windows XP Installer with a floppy using the F6 method drive.

  Your new PC does support Windows XP, it has Windows XP drivers available for it?  If this isn't the case, you will have a lot of crying by train to get there.

  John

• Access is denied on external hard drive

  Hello. I get the following message appears when I try to access my external hard drive: G:\ Access is denied. However, I can access the hard disk by clicking AutoPlay and choosing the second of the two identical icons labeled as 'open folder to view files '. The problem started when I used of Trend Micro Housecall to remove a virus from the reader. The problem occurs in XP and Vista. I tried to take ownership of the drive, but that isn't helping.

  Any help would be greatly appreciated.

  Thank you

  Hello. Thank you both for your help. I tried AVG and AVAST but they do not work, however, I went to my virus scan history and concluded that the virus was in the file autorun.inf on my drive. Then I found a good and quick tool Flash_Disinfector who quickly solved my problem.

  Thanks again for your help

• Trying to access the hard drive - error code 0 x 80070005

  I'm trying to be able to access my hard drive in my network and when I try to access my drive I get this error code

  Hello

  Maybe this can help,

  http://social.technet.Microsoft.com/forums/en-us/itprovistanetworking/thread/bda85413-231e-4b56-bd8f-cd84cf925d20/

  Jack MVP-networking. EZLAN.NET

• Access denied on external hard drive.

  I have an external drive, which works perfectly well. But I've just updated from vista to W7, and now I can not access the disk from that specific computer. I get access denied. On the properties, all users have full access. And the funny part is on my other computer, with the exact same OS, the drive works perfectly. So, I expect that there is a setting that I didn't know.
  Is there someone with good ideas on how to solve this problem?

  Hi I tried your instructions below to restore all my administrator permissions full on my external hard drive.

  1. click on Start , click all programs , and click Accessories .
  2. right click on command prompt , and then click run as administrator .
  3. in administrator: command prompt window.
  4. type
  takeown /F (external drive letter) and press ENTER.
  5 type
  CACLS (external drive letter) /G Administrator: F and press enter

  After that I followed these steps, my computer Windows 7 says that the drive is not accessible.  I plugged it to my old XP computer, and it also says "access denied."  I have a huge amount of important files there and I need to restore access, but I can't find an answer for how to cancel the steps I followed.  Please tell me how to reverse the steps I did your earlier suggestion.

• Reinstalled Vista access denied on external hard drive

  I reinstalled Vista and now I can't access my external hard drive.  I tried to do a right click on the drive and to allow access for all users on the Security tab with no luck.  Help, please

  Please see how appropriating a file or a folder in Windows XP , which also applies to Windows Vista and Windows 7. Boulder computer Maven
  Most Microsoft Valuable Professional

• 696e647863686b2e 7be error cannot access hard drive.

  A few days ago, I copied all my data on a 1 TB external HARD drive and used Lenovo one key recovery to reset my laptop to its factory settings, because I couldn't move to 8.1. Now when I plugged the hard drive of the laptop to get all my stuff it says an error similar to this every time:
  -H:\ is not accessible. Data error (cyclic redundancy check).
  -Drive not accessible. The parameter is incorrect.
  I checked and found a similar problem on the forums, so I ran chkdsk /F R/x H:
  Arriving on stage (2 of 5) it says: an unspecified error has occurred (696e647863686b2e 7be).

  I was wondering if anyone of you has a solution to this.
  Thank you

  Lenovo g500s core i5 clocked at 2.6 ghz 8 GB ram

  Hi Oliver,.

  I you suggest scan you the hard drive health using the Seagate tool and then check if works very well.

  Use SeaTools for Windows

  http://knowledge.Seagate.com/articles/en_US/FAQ/202435en

  Please post here with the State of the question and we will be happy to help you further.