Access point does not connect to my WLC

Similar Questions

• Connection of comments on the second WNR1000v3 as access point does not connect to Internet

  I have a WNR1000v3 (firmware V1.0.2.68_60.0.93NA) connected to the WAN and it works well. His IP address is 192.168.0.1, subnet 255.255.255.0, gateway 192.168.0.1, mask and DNS servers are on 8.8.8.8/8.8.4.4. DHCP is configured to 192.168.0.10 to 192.168.0.100. I have a guest connection configured and it works well.

  I have a * second * WNR1000v3 (same firmware) bound to the first as access by using these instructions: http://kb.netgear.com/app/answers/detail/a_id/23784/~/how-to-automatically-configure-a-netgear-route...

  I gave him the IP 192.168.0.2, subnet mask 255.255.255.0, gateway 192.168.0.1, and DNS servers again the value of Google. It has the same SSID wireless as the main router and I can move seamlessly between the two. The devices connected to the LAN ports on this access point work very well. Wireless connection works fine.

  I then configured the connection even guest on the second router (the one running in access point mode) and I can get an IP address when I use it. However I can't access the Internet. Ping 192.168.0.1, 192.168.0.2, and 173.194.33.137 (the IP local google.com) all fail.

  Guest connection is not supported on a router functioning as an access point? Or am I missing something really obvious?

  Thank you

  Bill

  @storm1985 I suspect that your configuration means that all the second router LAN ports will also forward only to the Internet. But this gives me a good idea to use another router just like an access point wireless for the connection of comments. (I seem to accumulate old routers.) Unfortunately, I don't have the time to try this out until late in the week, but I'll certainly do and report. Thank you!

• Citrix Access Gateway does not connect after update June 17

  I am running Citrix Access Gateway on a Windows 7 64-bit Client computer and as updates on 17 June, it does not connect.

  Have you checked with Citrix technical support? This would be my first step. If they cannot help, contact the technical support of MS for Windows Update.

  Support for Windows Update -http://support.microsoft.com/gp/wusupport

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  If you are not in the Canada or the United States, there are numbers to contact local support here:http://support.microsoft.com/common/international.aspx
  MS - MVP - Elephant Boy computers - don't panic!

• access point does not

  Why the hell is the hot spot of my android bionic phone does not work with my Rt surface Tablet? I have ice cream sandwich on my phone

  I tried again after the update of the firmware and changed the name to my device. It worked last night.

  Problem solved!

• Access points does not not with WLC

  Hi all

  I have a WLC 5508 in SHIFT mode and 14 1231 WAP connected on it already. However, I still spend my old controller 4404 9 WAP more towards the new 5508 controller. I can't get remaining 9 WAP register with new WLC. I found the rest of the WLC debug message. My WLC license is valid for 50 APs. If any of you guys have seen this? What I'm doing wrong here? Any advance is much appreciated.

  I have install LAG with 2 port departure 8 ports. Do not understand why it gives error of not having sufficient capacity.

  All reviews are much appreciated. Thanks in advance.

  * spamApTask4: 21 May 18:58:29.468: 00:23:04:c9:72:00 Echo Timer expiration: received no response from AP 00:23:04:c9:72:00 heartbeat (10:4:12:26 / 36602)

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:58:50.588: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  * spamApTask0: 21 May 18:59:00.589: BoardDataPayload is not found

  * spamApTask0: 18:59:00.636 May 21:

  * spamApTask0: 21 May 18:59:05.593: BoardDataPayload is not found

  * spamApTask0: 18:59:05.639 May 21:

  * spamApTask0: 21 May 18:59:53.564: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:59:53.565: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  * spamApTask0: 21 May 18:59:53.565: 00:13:60:7e:28:30 join priority Processing status = 0, priority of the PA entering 0, MaxLrads = 50, joined Aps = 14

  * spamApTask0: 21 May 18:59:53.565: 00:13:60:7e:28:30 request for discovery refusing AP 00:13:60:7e:28:30 - no AP Manager with available capacity

  Suppose that the CSD has been corrupted...

  Run the command "debug pm pki enable" on the WLC, copy the SSC and stick it on the WLC and see if that helps... Here is the link to do the same thing!

  http://www.Cisco.com/en/us/products/ps6366/products_configuration_example09186a00806a426c.shtml

  Let me know if that answers your question and please do not forget to note the useful messages!

  Concerning

  Surendra

• Mobile access point does not

  Well, I'll do that, nice and simple. Since the upgrade to the marshmallow on my Moto X pure on Verizon, I was not able to use my Mobile Hotspot.

  When I allow it, it reads just "Turning hot spot..." "it turns on but it never broadcasts the network name/SSID. I called Verizon to confirm that it is active on my account, and they are in no way the block on my particular line. (works fine on my other 3 lines)

  I do it for a living, so sometimes I need Internet when I'm on a subject. The only way I've been able to do is by attaching my phone via USB, but I prefer to use the hotspot.

  Short of doing a factory reset, someone has suggestions on how to solve this problem?

  Thank you!

  UPDATE:

  The factory reset did work. Kind of painting that I had to do to make it work, but at least it works now.

  Nothing short of a reset, no.

• Pavilion 15 ab214TX: access point does not (hosted network supported: No.) (Realtek RTl8723BE)

  I am not able to hotspot with the software or cmd. I have only checked in the Device Manager, there are no drivers "Hosted Microsoft Virtual network adapter" available. I have the latest driver for my wifi (Realtek RTl8723BE) card. Also in the cmd... supported hosted network said NO! can someone please me the latest drivers

  

  installed this version of the driver... I think it is assigned by microsoft... everything works fine now

  

• Access point does not not in Internet Explorer

  I created a page that contains hot spots on this subject with links to other pages. Hotspots work fine in Safari and Netscape, but not at all in Explorer. All the ideas that I was wrong?
  
  Jody

  It seems to work fine in the PC, but I have a Mac and cannot get the links to work.
  I do know not why this extra code is there, but when I deleted it, the links in Internet Explorer on my Mac worked flawlessly
  I do not do things well html, simply use Dreaamweaver to do the work.
  Thank you
  JO - D

• Airport utility: green points on the AirPort Extreme & Internet; Mini Mac does not connect to the internet.

  Airport utility shows green points on the AirPort Extreme and the Internet, but my my Mac mini does not connect to the internet. IPhones and 2 portable Windows connect very well, and see all the devices on the home network. The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem. I tried to stop and things start back up as if the installation of the internet for the first time. No joy.

  The airport connects using DHCP in Bridge Mode

  The router address is 192.168.80.1

  Address IPv4 is 192.168.80.2

  DNS server is the same as the router, but grayed out

  Mac Mini IPv4 Address is 192.168.80.3

  IPv6 automatically configures

  Also updated the firmware of the airport; no change.

  ISP guy was friendly but puzzled. He started at the top floor level Tech, so I do not know when I hear back.

  Any ideas to fix?

  Thank you.

  Post edited by: en maschera

  but my my Mac mini does not connect to the internet.

  The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem.

  Hello

  Network preferences may be damaged.

  Open the Finder. In the Finder menu bar, click go > go to folder

  Type or copy paste the following text:

  / Library/Preferences/SystemConfiguration

  Click OK, and then move all files in the SystemConfiguration folder to the trash.

  Restart your Mac. See if that makes a difference.

  Your Mac will generate a new SystemConfiguration folder for you.

  Then open AirPort Utility located in HD > Applications > Utilitiies

  Make sure that both Internet and Extreme are green.

  

• I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  I've set up another configuration of TCP/IP, but it does not connect. I need to access the 3 different machine networks. Any ideas?

  original title: alternate tcp/ip

  If by "alternate TCP/IP configuration" you mean the settings on this screen--> http://tinyurl.com/42kbqqz, then, to quote Inigo Montoya, "you keep using that Word. I don't think it means what you think it means. »

  The 'alternative' configuration settings tab, if you select "IP address private auto" (APIPA) or "specified user" is only used IF "obtain an IP address automatically" is set on the tab 'General' (http://tinyurl.com/8p9hn) AND the adapter cannot get an IP from a DHCP server.

  Most cable networks use a DHCP server to automatically assign IP addresses.  In this case, just plug your Ethernet cable and you're automatically configured and connected.

  If the problem is that your network requires a static IP address (that is, they use a DHCP server to automatically assign IP addresses), you will need a third-party network settings manager.  If you have an IBM (Lenovo) ThinkPad, you can use "Dial-up connections." IBM Otherwise, see this Google search (I have no experience with any of the applications shown, so I can't comment about them): http://www.google.com/#sclient=psy&hl=en&source=hp&q=network+configuration+switcher&pbx=1&oq=network+configuration+switcher&aq=f&aqi=g-v5&aql=&gs_sm=e&gs_upl=23l1333l1l1599l12l8l0l0l0l5l278l1344l0.7.1l8l0&bav=on.2,or.r_gc.r_pw.&fp=74e371c96a48f4b&biw=1024&bih=649

• How can I correct a problem accessing my firewall settings because the Group Policy client does not connect to windows?

  I have tried everything recently adjust the settings of the firewall from my window and a box appears saying that after an unidentified error, I can't access my firewall. After some research, I discovered that it was because my client group policy server does not connect and a small box appears saying that whenever I connect to my laptop. It is not effect my use of the internet at all, so I've never bothered to see what that meant until now I need to access my firewall. I tried to adjust the settings in group policy, but everything is gray and I can't change anything. I use an admin account so I don't know why I can't set the parameters. I'm completely stuck and I don't know that much about computers. Is there anything else I can try? I also tried a system restore, but it lasts for a long time and I can return only 5 days. Thank you

  Hi Sheldon,

  Are you connected or connected to a work network or domain? If so, this could be a policy governed by your network administrator, and you will not be able to change it.
  You might try to tell scientists on TechNet on your question to see if they have a better answer for you:
  http://social.technet.Microsoft.com/forums/en-us/itprovistanetworking/threads

• HP dv6tqe does not connect to internet

  Ok.  My laptop does not connect to the internet. It connected to the wifi very well, but does not connect to the internet. I tried the wiring and that no longer works. All other devices connect correctly. I had this problem before about a year ago or not, and it was solved when someone said on one of updates windows, causing this problem. I uninstalled and everything worked well.  I am unable to conclude that now. The router is a Verizon Fios / Actiontec M142RWR router.

  I am running windows 7.

  Any suggestions would be much appreciated.

  Thank you

  Hello @knn9413,

  I read your post about how you are not able to access the Internet on your laptop, and I'd be happy to help you in this case!

  For more to diagnose this problem, I recommend later in this document on the troubleshooting your wireless network and Internet access (Windows 7), as well as the problems in Internet Explorer 9 or earlier versions (Windows 7, Vista, XP). This should help you navigate on the Internet once more.

  If you are still not able to log in, please follow the steps below to check if the laptop computer can communicate with the network:

  Step 1. Click the Start button
  Step 2. In the search box, type "Command Prompt"

  Step 3. Click on command prompt

  Step 3. Type 'ping www.hp.com' and press ENTER.

  Step 4. Now, I'd like you to record the IP address that is being crazy

  Step 5. Type 'ping '.

  Two pings succeeded? If this isn't the case, I would like to clear your DNS. You can do so by following the steps I outlined below:

  Step 1. Click the Start button
  Step 2. In the search box, type "Command Prompt"
  Step 3. Right click on command prompt

  Step 4. Click on run as administrator
  Step 5. At the command prompt, type "ipconfig/flushdns".

  At this successful? If this isn't the case, I would like you to reset the TCP/IP stack. To do this follow the next series of steps that I have set out below:

  Step 1. Click the Start button
  Step 2. In the search box, type "Command Prompt"
  Step 3. Right click on command prompt

  Step 4. Click on run as administrator
  Step 5. Type "netsh winsock reset catalog" and press ENTER.
  Step 6. Type 'netsh int ip reset reset.log' and press ENTER.
  Step 7. Restart your computer

  Then, if none of the above works I would that try you to install Windows updates in Windows 7. I recommend that ensure you that all updates are completed.

  Then, I would like that try you the next series of steps, I have outlined for you below:

  Step 1. Click the Start button
  Step 2. In the search box, type "Windows Explorer"

  Step 3. Click on Windows Explorer

  Step 4. In the address at the top of the page bar try to distribute a video or download Google Chrome

  Then, if all else fails we will try to use using Microsoft System Restore (Windows 7) to restore your computer to a point in time before that this issue has been raised. This does not affect personal files that you have on your computer, but it will affect on the settings that you have changed or applications that you have installed since the time that you return to. These should be redone once we are finished.

  Finally, if we still have the issue we are at the point where we have to use the HP support document: backup of files (Windows 7) to backup your personal files. Once we did it with success I would like to see again you and follow the steps in the HP Support document: performing a recovery of HP (Windows 7) system, which will guide you through restoring your computer to the factory.

  NOTE: This will destroy everything on your computer in order to ensure that you have backed up everything you want to keep.

  reference: http://h30434.www3.HP.com/T5/other-desktop-PC-questions/Ethernet-not-working-on-slimline-desktop/m-p/3985804/highlight/true#M47729

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning

• WRT150N access restrictions does not

  Good day everyone.

  I read the messages that are similar to my problem in the forum, but none of the suggested solutions solved my current dilemma.

  I use a WRT150N with firmware v1.00.5. I have a setup of Linux with Squid, connected to the network with the modem router 192.168.23.254. The WRT150N has a gateway of 192.168.23.1. The WRT150N is also connected to an Apple Base Station that serves as a Point of access for users of WiFi.

  Squid limits access to the IP addresses listed under the passerelle.254. But once I change my gateway to 23.1, everything is accessible. I want to block sites as well as on the WRT150N. But whenever I try to put a new restricted access, it does not work.

  

  I put in the IP addresses on which to apply this restriction:

  

  It ignores addresses is because addresses are reserved. I click on save settings here and I save the settings again on the home page.

  Whenever I try to test on the addresses given, I can still access the pages. Is there something that I am missing?

  Thanks in advance for your answers.

  Try to update / re Flash the firmware of your router.

  Connect computer with the Ethernet cable to the Ethernet port on the router.

  Download the firmware on the Linksys site.

  Open the router configuration page.

  Go to the tab Administration and go to the update of the Firmware tab sub.

  Browse and select the downloaded firmware and update the firmware.

  After the upgrade of the firmware reset and reconfigure the router settings manually.

  And see if that helps you.

• ACS network access Restriction does not. He denies it, but allow.

  I have a problem with the restrictions of access to the network on the Group of ACS configuration.

  I configured the NAR in a group field and set it to deny access besed on client AAA, a wireless LAN controller.

  But users of this group is still able to connect wireless controller.

  Newspapers in GBA shows that the fields are right. the right user in the right of the group in good AAA client, but does not deny.

  Put in place DNIS also supports the restriction. This is how it should be configured,

  -Procedure for the configuration of NAR:

  (1) go to User Configuration---> select the user name that you want to restrict.

  2) go into Restrictions on access network (OAN) option.

  (3) by user defined network access Restrictions.

  (4) check "define CLI/DNIS-based access restrictions.

  (5) select "reject the call or Access Point.

  (6) in the dropdown AAA client list - select the name of the device on which the user does not connect.

  (7) for Port - Development *.

  (8) in CLI - use *.

  (9) for DNIS - development *.

  (10) click on submit

  Kind regards

  ~ JG

  Note the useful messages

• Messages does not connect to the Yahoo IM account?

  Messages app v9.2, currently works very well with my Google account and iMessage, also worked with my Yahoo Messenger account, but recently (today?) does not connect to it.

  I know that Yahoo has made changes to their Instant Messaging System. This change affected only Messages?

  Hello

  I can't connect either (I didn't realize that I do not use)

  However going on the Yahoo Site and change the password does nothing.

  With the help of their option 'insecure Apps' does nothing no more (there was an email saying I was using access to messaging through an unsafe application - but I have not used their messaging service for a very long time.)

  It does say read more suggests, is not Mail (after OS X 10.9 is OK)

  He does not on access to their e-mail service.

  There is no option in Messages to try to activate disable SSL you can with AIM or Jabber accounts

  I have looked in the help (a little) but still found nothing.

  

  20:49 Tuesday. October 4, 2016

   iMac 2.5 Ghz i5 2011 (El Capitan)
   G4/1GhzDual MDD (Leopard 10.5.8)
   MacBookPro (Snow Leopard 10.6.8) 2 GB
   Mac OS X (10.6.8).
   iPhone and iPad (2)