access remote E3000
Sorry, this becomes extremely confused now: in your first post, you wrote your main LAN uses addresses 192.168.10. * now all of a sudden your access point is 192.168.30. *. It seems as if you mix a lot of different IP addresses of your local network.
What is the IP address of your main router on the VLAN port to which the E3000 is connected?
One of the LAN ports of the E3000 connected to your main router do you have?
Installation of LAN - LAN: reset the router, and then open the web interface at http://192.168.1.1/ from a wired computer.
1. on the main configuration page, change the address LAN IP of 192.168.1.1 to 192.168.30.50.
2. on the same page, disable the DHCP server.
3. save the settings and unplug the computer.
4. now one of the LAN ports numbered from the wire to the main router E3000.
Now you should be able to open the web interface http://192.168.30.50/ however, it is not possible to access the web interface from outside your LAN 192.168.30. *. This is because you use the E3000 in a way for which it has not been designed to, in the strict sense.
In this way, wired and wireless clients connected to the E3000 has access to the entire LAN. Everything is in the same local network.
Variant: WAN - LAN connection. Reset the router, and then open the web interface at http://192.168.1.1/ from a wired computer.
1. on the main Setup page, leave the type of internet connection on automatic/DHCP or change static IP address and set something like: IP 192.168.30.50, subnet mask 255.255.255.0, gateway 192.168.30.1, DNS 192.168.30.1 (or one you use as DNS server).
2. on the same page, change the address LAN IP of 192.168.1.1 to 192.168.20.1 (or whatever it is that you want it to be, expect 192.168.30. *).
3. save the settings.
4 unplug the computer and the internet port of wire in the main router.
DO NOT disable the NAT.
DO NOT disable the DHCP server on the E3000.
Now, you can open the web interface in a computer cable connected to the E3000 to http://192.168.20.1/ you can enable remote management in the web interface, and it should allow access to the web interface, at http://192.168.30.50/ (assuming that the static IP address above).
This way, you have two LANs: a 192.168.20 * LAN E3000 and your main routers LAN 192.168.30. *. The E3000 LAN accesses the main LAN but not vice versa.
These are essentially two alternatives you have. You can choose only one.
Tags: Linksys Routers
Similar Questions
-
Our computer was accessed remotely this afternoon, how can we prevent this?
We have a Mac Mini, with OS X 10.6.8 using NetZero DSL as our internet provider and Firefox as your browser. Our computer was accessed remotely through LogMeIn (rescue), but it seems that the person or the group failed to hack into our computer. Are there settings in Firefox that could prevent this from happening in the future? Thank you...
Firefox is a web browser not a firewall.
I agree that it's more to do with your operating system and the LogMeIn software on ensuring that only you have access when you need to.
-
My camera iPhone 5s is accessed remotely? Whenever I use my phone torch ends up taking videos. Is it possible for a person to access my camera through the torch. We share the same Apple ID
N °
but maybe you tap the camera icon (bottom-right) when you press the icon of the torch (with the other hand maybe?)
-
How a cRIO can access remote systems VISA resources?
I have a NI 9871 RS485 module on an ethernet 9148 RIO.
I have also a laptop and a cRIO 9073.
I can access each of the 9871 serial ports on the computer but not the 9073.
When you try to access it from the cRIO, I get error:-1073807192, VISA: (Hex 0xBFFF00A8) is denied access to the resource or to the remote machine. This is due to the lack of sufficient privileges for the current user or the machine.
How the cRIO can access the serial ports of the module 9871 on the ethernetRIO?
Or how a remote access cRIO visa resources?
Or how a cRIO can have sufficient privileges to access remote resources from visa?
Thank you for your help.
LabVIEW 2010 & VISA 5.1 on pc
NOR-RIO 4.0 and 5.1 VISA & NI 9871 SERIES scan engine support on cRIO and eRIO
Hi Woss,
It is possible that your RIO Ethernet has some parameters of active access which is to prohibit the connection to serial ports. You can change these settings in a position and Automation Explorer (MAX) for your device by going to the device under remote systems, expanding the category of software under it and choosing NI-VISA. There will be a tab in the right pane of MAX called Options of VISA. In this tab, select Server VISA > security to access these settings.
From there, you should be able to add the IP address of the RIO device that needs to access the VISA on the RIO Ethernet server. Once you have changed these settings, just click on register at the top of the window and allow the unit to restart. Let me know if that helps!
-
1920 router access remote vpn LDAP living
Hello
What is required for a router in 1920 use AnyConnect and/or also integrate with AD LDAP?
Currently, this router supports legacy clients and has these licenses:
Technology for the Module package license information: "c1900".
-----------------------------------------------------------------
Technology-technology-package technology
Course Type next reboot
------------------------------------------------------------------
IPBase ipbasek9 ipbasek9 Permanent
Security securityk9 Permanent securityk9
given none none noneThe vpn to access remote client inherited integrate with AD LDAP?
Thank you.
As long as you are on IOS 15.3.3M3 or better, you have all the licenses you need for 3.1 AnyConnect run on your 1921.
The guide to directly connect your router to LDAP can be found here:
Personally, I would avoid directly interfacing with LDAP, because it can be a complex arrangement. While it can be done, it's easier to have your router to connect to the NPS Microsoft via RADIUS server for your authentication.
-
Split tunneling cannot access remote host
Hi guys,.
Having this problem by which I am able to connect the Anyconnect client but unable to ping / access of remote servers. See below for the config of the SAA;
Any ideas would be a great help, thank you!
ASA Version 9.1 (1)
!
ASA host name
enable the encrypted password xxxxxxx
xxxxxxxxxxxxx encrypted passwd
names of
mask of local pool AnyPool 10.0.0.1 - 10.0.0.10 IP 255.255.255.0
!
interface GigabitEthernet0/0
nameif outside
security-level 0
IP address 203.106.x.x 255.255.255.224
!
interface GigabitEthernet0/1
nameif inside
security-level 99
IP 172.19.88.254 255.255.255.0
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
passive FTP mode
clock timezone 8 MYT
the SVR object network
Home 172.19.88.11
e-mail server in description
network of the NETWORK_OBJ_172.19.88.0_24 object
172.19.88.0 subnet 255.255.255.0
network of the VPN-POOL object
10.0.0.0 subnet 255.255.255.0
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_0
ICMP service object
area of service-purpose tcp - udp destination eq
the destination hostname eq tcp service object
the purpose of the tcp destination eq https service
the purpose of the tcp destination eq imap4 service
the purpose of the tcp destination eq nntp service
the purpose of the tcp destination eq pop3 service
the purpose of the tcp destination eq smtp service
the purpose of the tcp destination eq telnet service
Outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_0 any object SVR
Outside_access_in list extended access allow TCPUDP of object-group a
Outside_access_in access-list extended ip any any idle state to allow
Internal_access_in list extended access allow TCPUDP of object-group a
Internal_access_in access-list extended ip any any idle state to allow
SPLIT_TUNNEL list standard access allowed 10.0.0.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer 16384
buffered logging critical
asdm of logging of information
Debugging trace record
exploitation forest flash-bufferwrap
record level of the rate-limit 1000 1 2
management of MTU 1500
MTU 1500 internal
Outside 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 711.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
!
the SVR object network
203.106.x.x static NAT (indoor, outdoor)
!
source of auto after the cessation of NAT (inside, outside) dynamic interface
Internal_access_in in interface internal access-group
Access-group Outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 203.106.23.97 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
LOCAL AAA authorization command
Enable http server
http 192.168.1.0 255.255.255.0 management
http authentication certificate management
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
No vpn sysopt connection permit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
card crypto Outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
Outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = ASA
Configure CRL
Crypto ca trustpoint Anyconnect_TrustPoint
registration auto
name of the object CN = ASA
anyconnect_rsa key pair
Configure CRL
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
trustpool crypto ca policy
string encryption ca Anyconnect_TrustPoint certificates
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev2 access remote trustpoint Anyconnect_TrustPoint
Telnet timeout 3
SSH 172.19.88.0 255.255.255.0 internal
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 15
Console timeout 0
management of 192.168.1.100 - 192.168.1.200 addresses dhcpd
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP server 119.110.97.148 prefer external source
SSL-trust outside Anyconnect_TrustPoint point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 3
AnyConnect profiles AnyConnect_client_profile disk0: / AnyConnect_client_profile.xml
AnyConnect enable
attributes of Group Policy DfltGrpPolicy
VPN-tunnel-Protocol ikev1, ikev2 ssl clientless ssl ipsec l2tp client
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list SPLIT_TUNNEL
Group Policy 'GroupPolicy AnyConnect' internal
Group Policy attributes "GroupPolicy AnyConnect"
value of server WINS 172.19.88.11
value of server DNS 172.19.88.11
SSL VPN-tunnel-Protocol ikev2 client ssl clientless
WebVPN
AnyConnect value AnyConnect_client_profile type user profiles
attributes global-tunnel-group DefaultWEBVPNGroup
address pool AnyPool
tunnel-group "AnyConnect" type remote access
attributes global-tunnel-group "AnyConnect".
address pool AnyPool
strategy-group-by default "GroupPolicy AnyConnect"
tunnel-group "AnyConnect" webvpn-attributes
Group-alias "AnyConnect" activate
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
Hi Max,.
Please send me the output of 'see the anyconnect vpn-sessiondb' once connected with VPN.
And try to add the following configuration and see if that helps:
NAT (inside, outside) 1 static source NETWORK_OBJ_172.19.88.0_24 NETWORK_OBJ_172.19.88.0_24 static destination VPN-VPN-POOL no-proxy-arp-route search
And one more qusetion do you use split tunnel? If yes then you must make the following changes, because your split tunnel is incorrect, in the split tunnel, you have configured the address pool of vpn. Please make the following change:
no access list SPLIT_TUNNEL standards not allowed 10.0.0.0 255.255.255.0
Standard access list SPLIT_TUNNEL allow 172.19.88.0 255.255.255.0
Group Policy attributes "GroupPolicy AnyConnect"
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list SPLIT_TUNNEL
Let me know if this can help, or if you have any questions, more about it.
Thank you
Jeet Kumar
-
2 VPN SITE to SITE with ACCESS REMOTE VPN
Hello
I have a 870 router c and I would like to put 2 different VPN SITE to SITE and access remote VPN (VPN CLIENTS) so is it possible to put 3 VPN in the router even if yes can u give me the steps or the sample configuration
Concerning
Thus, on the routers will be:
Cisco 2611:
LAN: 10.10.10.0/24
access-list 100 permit ip 10.10.10.0 0.0.0.255 10.10.20.0 0.0.0.255
access-list 100 permit ip 14.1.1.0 0.0.0.255 10.10.20.0 0.0.0.255--> VPNPOOL
!
10 ipsec-isakmp crypto map clientmap
defined by peer 172.18.124.199
match address 100
!
IP local pool ippool 14.1.1.1 14.1.1.254
!
access-list 120 allow ip 10.10.10.0 0.0.0.255 14.1.1.0 0.0.0.255
access-list 120 allow ip 10.10.20.0 0.0.0.255 14.1.1.0 0.0.0.255 --> NETWORK REMOTE
!
crypto ISAKMP client configuration group ra-customer
pool ippool
ACL 120
!
Please note that the configuration is incomplete, I added that relevant changes, you should bring to the allow clients of RA through the LAN-to-LAN tunnel, of course, the LAN-to-LAN settings should match to the other side of the tunnel that is mirror of ACL, NAT and so on.
HTH,
Portu.
-
Cannot access remote network by VPN Site to Site ASA
Hello everyone
First of all I must say that I have configured the VPN site-to site a million times before. Stuck with it. First of all I can't ping outside the interface of my ASA remote. Secondly, VPN is in place, but no connectivity between local networks
ASA local:
hostname gyd - asa
domain bct.az
activate the encrypted password of XeY1QWHKPK75Y48j
XeY1QWHKPK75Y48j encrypted passwd
names of
DNS-guard
!
interface GigabitEthernet0/0
Shutdown
nameif vpnswc
security-level 0
IP 10.254.17.41 255.255.255.248
!
interface GigabitEthernet0/1
Vpn-turan-Baku description
nameif outside Baku
security-level 0
IP 10.254.17.9 255.255.255.248
!
interface GigabitEthernet0/2
Vpn-ganja description
nameif outside-Ganja
security-level 0
IP 10.254.17.17 255.255.255.248
!
interface GigabitEthernet0/2.30
Description remote access
VLAN 30
nameif remote access
security-level 0
IP 85.*. *. * 255.255.255.0
!
interface GigabitEthernet0/3
Description BCT_Inside
nameif inside-Bct
security-level 100
IP 10.40.50.65 255.255.255.252
!
interface Management0/0
nameif management
security-level 100
IP 192.168.251.1 255.255.255.0
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
name-server 192.168.1.3
domain bct.az
permit same-security-traffic intra-interface
object-group network obj - 192.168.121.0
object-group network obj - 10.40.60.0
object-group network obj - 10.40.50.0
object-group network obj - 192.168.0.0
object-group network obj - 172.26.0.0
object-group network obj - 10.254.17.0
object-group network obj - 192.168.122.0
object-group service obj-tcp-eq-22
object-group network obj - 10.254.17.18
object-group network obj - 10.254.17.10
object-group network obj - 10.254.17.26
access-list 110 scope ip allow a whole
NAT list extended access permit tcp any host 10.254.17.10 eq ssh
NAT list extended access permit tcp any host 10.254.17.26 eq ssh
access-list extended ip allowed any one sheep
icmp_inside list extended access permit icmp any one
icmp_inside of access allowed any ip an extended list
access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh
RDP list extended access permit tcp any host 192.168.45.3 eq 3389
rdp extended permitted any one ip access list
sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0
NAT-vpn-internet access-list extended ip 192.168.121.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 172.26.0.0 allow 255.255.255.0 any
NAT-vpn-internet access-list extended ip 192.168.122.0 allow 255.255.255.0 any
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.60.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.40.50.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 192.168.0.0 255.255.0.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 172.26.0.0 255.255.255.0
access-list sheep-vpn-city scope ip 192.168.121.0 allow 255.255.255.0 10.254.17.0 255.255.255.0
GHC-ganja-internet access-list extended ip 192.168.45.0 allow 255.255.255.0 any
Standard access list Split_Tunnel_List allow 192.168.16.0 255.255.255.0
azans 192.168.69.0 ip extended access-list allow 255.255.255.0 any
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.121.0 255.255.255.0
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.80.0 255.255.255.0
pager lines 24
Enable logging
emblem of logging
recording of debug console
recording of debug trap
asdm of logging of information
Interior-Bct 192.168.1.27 host connection
flow-export destination inside-Bct 192.168.1.27 9996
vpnswc MTU 1500
outside Baku MTU 1500
outside-Ganja MTU 1500
MTU 1500 remote access
Interior-Bct MTU 1500
management of MTU 1500
IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0
IP local pool ssl 192.168.121.130 - 192.168.121.200 mask 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any outside Baku
ICMP allow access remotely
ICMP allow any interior-Bct
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
global (outside-Baku) 1 interface
global (outside-Ganja) interface 2
3 overall (RAS) interface
azans access-list NAT 3 (outside-Ganja)
NAT (remote access) 0 access-list sheep-vpn-city
NAT 3 list nat-vpn-internet access (remote access)
NAT (inside-Bct) 0-list of access inside_nat0_outbound
NAT (inside-Bct) 2-nat-ganja access list
NAT (inside-Bct) 1 access list nat
Access-group rdp on interface outside-Ganja
!
Router eigrp 2008
No Auto-resume
neighbor 10.254.17.10 interface outside Baku
neighbor 10.40.50.66 Interior-Bct interface
Network 10.40.50.64 255.255.255.252
Network 10.250.25.0 255.255.255.0
Network 10.254.17.8 255.255.255.248
Network 10.254.17.16 255.255.255.248
redistribute static
!
Access remote 0.0.0.0 0.0.0.0 85.*. *. * 1
Outside-Baku route 10.0.11.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.33.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.150.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 10.0.170.0 255.255.255.0 10.254.17.10 1
Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1
Route outside Baku 10.254.17.32 255.255.255.248 10.254.17.10 1
Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.27.0 255.255.255.0 10.254.17.10 1
Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1
Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.66.0 255.255.255.0 10.254.17.18 1
Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1
Outside-Baku route 192.168.80.0 255.255.255.0 10.254.17.11 1
Access remote 192.168.121.0 255.255.255.0 85.132.43.1 1
Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1
Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1
Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1
Route inside-Bct 192.168.254.0 255.255.255.0 10.40.50.66 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede GANYMEDE +.
AAA-server GANYMEDE (Interior-Bct) 192.168.1.8
key *.
AAA-server GANYMEDE (Interior-Bct) 192.168.22.46
key *.
RADIUS protocol AAA-server TACACS1
AAA-server TACACS1 (Interior-Bct) host 192.168.1.8
key *.
AAA-server TACACS1 (Interior-Bct) host 192.168.22.46
key *.
authentication AAA ssh console LOCAL GANYMEDE
Console to enable AAA authentication RADIUS LOCAL
Console Telnet AAA authentication RADIUS LOCAL
AAA accounting ssh console GANYMEDE
Console Telnet accounting AAA GANYMEDE
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 Interior-Bct
http 192.168.139.0 255.255.255.0 Interior-Bct
http 192.168.0.0 255.255.255.0 Interior-Bct
Survey community SNMP-server host inside-Bct 192.168.1.27
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
Crypto ipsec transform-set esp-3des esp-md5-hmac raccess
Crypto ipsec transform-set esp-3des esp-sha-hmac vpnclienttrans
Crypto ipsec transform-set vpnclienttrans transport mode
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.10
card crypto mymap 10 transform-set RIGHT
correspondence address card crypto mymap 20 110
card crypto mymap 20 peers set 10.254.17.11
mymap 20 transform-set myset2 crypto card
card crypto mymap interface outside Baku
correspondence address card crypto ganja 10 110
10 ganja crypto map peer set 10.254.17.18
card crypto ganja 10 transform-set RIGHT
card crypto interface outside-Ganja ganja
correspondence address card crypto vpntest 20 110
peer set card crypto vpntest 20 10.250.25.1
newset vpntest 20 transform-set card crypto
card crypto vpntest interface vpnswc
vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1
card crypto interface for remote access vpnclientmap
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = gyd - asa .az .bct
sslvpnkeypair key pair
Configure CRL
map of crypto DefaultCertificateMap 10 ca certificatecrypto isakmp identity address
ISAKMP crypto enable vpnswc
ISAKMP crypto enable outside-Baku
ISAKMP crypto enable outside-Ganja
crypto ISAKMP enable remote access
ISAKMP crypto enable Interior-Bct
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 30
No vpn-addr-assign aaa
Telnet timeout 5
SSH 192.168.0.0 255.255.255.0 Interior-Bct
SSH timeout 35
Console timeout 0
priority queue outside Baku
queue-limit 2046
TX-ring-limit 254
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.168.1.3
SSL encryption, 3des-sha1 rc4 - md5 aes128-sha1 sha1-aes256
SSL-trust point ASDM_TrustPoint0 to vpnlb-ip remote access
SSL-trust ASDM_TrustPoint0 remote access point
WebVPN
turn on remote access
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal group ssl policy
attributes of group ssl policy
banner welcome to SW value
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
group-lock value SSL
WebVPN
value of the SPS URL-list
internal vpn group policy
attributes of vpn group policy
value of DNS-server 192.168.1.3
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the PFS
BCT.AZ value by default-field
ssl VPN-group-strategy
WebVPN
value of the SPS URL-list
IPSec-attributes tunnel-group DefaultL2LGroup
ISAKMP retry threshold 20 keepalive 5
attributes global-tunnel-group DefaultRAGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultRAGroup
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
IPSec-attributes tunnel-group DefaultWEBVPNGroup
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.10 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.10
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type SSL tunnel-group remote access
attributes global-group-tunnel SSL
ssl address pool
Authentication (remote access) LOCAL servers group
Group Policy - by default-ssl
certificate-use-set-name username
Group-tunnel SSL webvpn-attributes
enable SSL group-alias
Group-url https://85. *. *. * / activate
tunnel-group 10.254.17.18 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.18
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
tunnel-group 10.254.17.11 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.11
pre-shared key *.
ISAKMP retry threshold 20 keepalive 5
type tunnel-group DefaultSWITGroup remote access
attributes global-tunnel-group DefaultSWITGroup
raccess address pool
Group-RADIUS authentication server
Group Policy - by default-vpn
IPSec-attributes tunnel-group DefaultSWITGroup
pre-shared key *.
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
class flow_export_cl
flow-export-type of event all the destination 192.168.1.27
class class by default
flow-export-type of event all the destination 192.168.1.27
Policy-map Voicepolicy
class voice
priority
The class data
police release 80000000
!
global service-policy global_policy
service-policy interface outside Baku Voicepolicy
context of prompt hostnameCryptochecksum:4f35f975ba7a0c11f7f46dfd541d266f
: end
GYD - asa #.ASA remote:
ASA Version 8.2 (3)
!
ciscoasa hostname
activate the encrypted password of XeY1QWHKPK75Y48j
2KFQnbNIdI.2KYOU encrypted passwd
names of
DNS-guard
!
interface Ethernet0/0
nameif inside
security-level 100
IP 192.168.80.14 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 10.254.17.11 255.255.255.248
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
nameif management
security-level 100
no ip address
management only
!
boot system Disk0: / asa823 - k8.bin
passive FTP mode
access-list 110 scope ip allow a whole
192.168.80.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.0.0 255.255.0.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
management of MTU 1500
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ICMP allow any inside
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside) 0 access-list sheep
Route outside 0.0.0.0 0.0.0.0 10.254.17.9 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.80.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto ipsec transform-set newset aes - esp esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-sha-hmac myset2
life crypto ipsec security association seconds 2147483646
Crypto ipsec kilobytes of life security-association 2147483646
correspondence address card crypto mymap 10 110
card crypto mymap 10 peers set 10.254.17.9
mymap 10 transform-set myset2 crypto card
mymap outside crypto map interface
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 20
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
crypto ISAKMP policy 30
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 40
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPNtunnel-group 10.254.17.9 type ipsec-l2l
IPSec-attributes tunnel-group 10.254.17.9
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostnameCryptochecksum:1c1ac60e2fb84f65269d15d53f27c21b
: end
ciscoasa # $Still, I can't ping ASA remote outside from outside of the Local interface. And there is no connectivity between the 192.168.80.0 distance and local don't say 192.168.1.0. I have run out of ideas
Would appreciate any help. Thank you in advance...
If the tunnel is up (phase 1), but no traffic passing the best test is the following:
Add order management-access to the Interior , and then try to PING the intellectual property inside ASA counterpart.
inside x.x.x.x ping --> x.x.x.x is the IP of the ASA peer inside
The test above shows if the traffic passes through the tunnel (check encrypted/decrypted packets of sh cry ips its).
Test on both directions.
Please post the results.
Federico.
-
Newbie question: in what configuration file < flex: access remote destination > tags go?
I seem to have read the document integration spring/Blaze about 10 times, but I don't know where to put all my < flex: access remote-Ref destination = "yaddayaddaService" / > tags. I don't want annotation allows you to set these remote destinations.
Should it go in the spring configuration file that I use for the servlet of AMF endpoint (as specified by the contextConfigLocation parameter). Or they go to a high-level cross-servlet configuration file?
What is the usual way to deal with these?
Hello
The convention is to declare:
1 declare the Spring beans (for example yaddayaddaService) in the files specified by the parameter contextConfigLocation.
2. Add the Spring - Flex specific configuration (configure message agent, declare destinations) in
WEB-INF\flex- servlet.xml, assuming that you have configured the model of Message Broker URL as follows in the web.xml file:
Flex
org.springframework.web.servlet.DispatcherServlet
1
Flex
messagebroker / *.
The repository SVN BlazeDS/distribution contains the spring sample webapp (spring - samples.war) that you can watch as well.
Hope that helps.
Rohit
-
Access remote USB to E3000 problem?
Hello
I recently got the E3000 router because it has USB and is simultaneous dual band router.
It is connected to the ATT modem + router. I disabled wireless 2wire ATT modem and connected the linksys router.
Now, after much playing with it, I have configured the USB key to work and being visible on the network, Media Server also seems to work very well.
Now I need help with the following:
Now what I'm trying to do is have remote access to my USB connected hard drive on the internet.
Also, I want to put the USB HDD as media download drive. For example if I'm downloading a large file or download torrent I want it either directly into the USB connected HDD.
Also in my computer/network, I have the disc visible as a computer and when I double click on it, it ask me for the admin and password user id and I have access available files, that I do not understand why is this? Because the same thing can be achieved by "map network drive" then what is the difference between the two?
Waiting for answer
Thanks for the help guys
For your 1st question: Yes, the problem is with your configuration. The E4200 needs direct access to the internet, but in this case it is "hidden" behind a NAT (your att gateway) device. You must find a way to dumb down your front door so that it becomes just a modem.
If you have att u-verse, then you must look for a story on your gateway 2wire called demilitarized zone more and put in place to allow your router to be seen on the internet that will allow you to remote access to the storage unit.
As for your 2nd question: there is no way to do it. Your pc should be while you download files.
-
Online remote access to my PC and my credentials and personal information were stolen. I had several compromised online accounts. I had Windows Live using their remote access three times service and my computer is always connected remotely. I'm stuck using many admin capabilities. The task manager says there is more than one user, but I'm the only visible. Name resolution Protocol, Peer Networking peer Peer Networking Identity Manager, Remote Procedure Call, Mapper by point final CPP, Windows connect now Config clerk, are among the many active services right now. Resource monitor shows me connected to a remote network, there are other IPS listed other than mine. I found a hidden desk top, with map of the network... including an android phone, a Tablet PC Input Panel with a foreign alphabet. There are many programs, I've never added to my PC. I find the hidden devices that are listed as part of a network, they do not belong to my PC. My modem has no Wy - Fy, or my router. I removed the ethernet cables... the power cord, monitor, keyboard and mouse. My modem has been disconnected from the external source and the router, but was still connected and powered on, all the lights were not on showing no connection. Very shortly, I saw the indicatator of DSL connection will begin to Flash. I unplugged the modem. A minute later, I heard the ping and the squeal to initialize an internet connection from my flat satellite receiver. When I checked my PC, he was very quietly running in stealth mode, apparently fleeing electricity drawn from the speakers I left wired. I'm sure you can tell just by reading that I don't know much about computers. This situation has worried me. Microsoft said that they fixed access points and it was clean from the virus and malware. Apparently it is not. I ask to change my IP address or security credentials, regardless of which is used to verify my identity, my question is did not answer, leaving unresolved. I am very concerned because all certificates of proof of identity online, IPaddress, Signatures etc., were copied and stolen. The hackers have the opportunity to make me look at will and have used it to seep into my GMAIL, FACEBOOK and some other accounts. I am at a loss. I will contact Microsoft Live again... I paid cover me 30 days it wil expire on 5 December. I guess that my cyber identity has been stolen. Is it me as a victim of identity theft? Should the technicians who worked on my computer could solve my problem to be hacked and stolen ID. I made a police report a few weeks, I was told it wasn't a crime unless I could prove identity theft, that was before I had no Service. Contact the FBI. Any help or advice or anything at all that you can provide would be greatly appreciated. I don't know which forum to post in both, if I choose wrong... Please help to direct my concerns to where it can be treated... Thank you a lot =)
The first thing you need to do is change ALL your passwords on all accounts - using a known machine - cleaning - and NOT connect to them with a mchine to which you think is infected.
Then only you should undertake the cleaning of the machine.
-
A new installation of Windows SBS 2011 Essentials. We have the following text:
1 / web remote access is fine for the administrator account, server and work stations are available and accessible francs
2 - However, if any user uses the web remote access, it is able to see the shared folders but no computers available.
3. from the server, I am able to connect locally remotely and manage the client computer (local, not through the internet)
Hello
I suggest you send the query in the link for assistance.
http://social.technet.Microsoft.com/forums/en/smallbusinessserver/threads -
Access remotely from a mobile phone
I think the upgrade from my cell phone. I have currently access to my work pc using the remote connection feature. Please some advice if that would be possible on a mobile phone function window package IE to connect using my cell phone to my work pc.
It will help you: http://www.windowsphone.com/en-US/apps/5f1b2f5c-7caa-48a2-b360-eb3bc91cfee8
-
Cannot access remote through Windows Live Messenger
During the years I helped my mother by remote access through Windows Live Messenger, but in recent days the small program that usually appears which shows two computers, try to connect are missing and I get the error message cannot display the page. If anyone has had the same problem and how solved you this problem?
Submit all Live queries on the forum right here:
Windows Live Solution Center
http://windowslivehelp.com/ -
deceived by false windows phone technicians to access remotely to the computer... worried...
I allowed remote technical support of false windows phone access until I realized what was happening. I didn't not give money and now when I start my computer I need to enter a password. I've never had to do. They still have access to my computer? can they see my personal passwords and banking passwords and e-mail? It was a month ago and my computer is running slowly now and im worried of my personal info. I got the password of the so-called technician so I can use my computer again, but I can't change this password! I'm worried...
If anyone can answer all these questions, that would be greatNicoleHello Nicole,.
Never give someone who calls you and you don't know, remote access to your PC.
In response to your questions, yes they still have access to your PC. Yes they have probably taken note your bank details and other personal information on your PC.
Inform your bank that your PC has been compromised. Then reinstall completely Windows on your PC operating system. Change each password, including those that you use to log on to your PC.
Microsoft would never call you on your PC problems. The only exception is if you have a prepaid support contract with Microsoft, which, obviously, you have not.
This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.
John Barnett MVP: Windows XP Expert associated with: Windows Expert - consumer: www.winuser.co.uk | vistasupport.mvps.org | xphelpandsupport.mvps.org | www.silversurfer-Guide.com
Maybe you are looking for
-
2009 macbook pro won't start, stay asleep
I closed the macbook in the middle of a game of solitaire. I came back in 5 minutes and it opens to a black screen. It will awaken no sleep, regardless of the keys on which I rely on. I sometimes hear a hum. Please help - I need this for a presen
-
HOW TO PLAY PERSONAL ON IPHONE PLAYLIST
I have a great on my iMac iTunes library. I don't want this on my iPhone6. And I don't want the music to Apple. The ONLY thing I want to do is to move a small personal playlist of my iMac to my my iPhone. Could someone please explain how to do th
-
Re: No wireless connection on Tecra A9
Just bought this laptop yesterday. This morning, I tried to conncet to the use of wireless internet. It is not connet. He kept looking and saying "absorbing the network address. It detects my network without problem. IAM using XP Pro with service pac
-
I'm in the mood for buying an SSD and have found a lot of things on an Intel 520 120 GB one. I'm just curious to know if she will be training / made in my T430. I found no Lenovo master about it. We know?
-
Adding a disclaimer to every vi in a project.
I need to add a disclaimer of limited rights to every vi in a project. Is there a method to add the text in the field of documentation to all the s vi in a project? Is there a better way to do this? Thank you.