ACL to DRAC 5

Having probs getting ACL on my DRAC goes.
It is connected to the 1/g5.

If no ACL, works fine (but not ACL).
If I allow the ports 443 & 5900, can connect (using telnet) at 5900, but NOT of 443.

Console (config) #access - list drac permit tcp any any eq 443
Console (config) #access - list drac permit tcp any any eq 5900
Console (config) #interface ethernet 1/g5
Console (config-if-1/g5) #ip access-group drac on

All advice welcome!

Tags: Dell Switches

Similar Questions

Reset home folder permissions and the default ACL on macOS Sierra?

A tool that I've used in the past to troubleshooting doesn't seem to be available in macOS Sierra.

There was a procedure in el captain to reset the permissions of file and ACLs in start in recovery mode, by running the command terminal, resetpassword. This command pulls up a GUI in Sierra as el cap but the "reset the user permissions and ACLs" option is no longer there.

This article describes the procedure to el captain

http://appletoolbox.com/2016/07/fix-corrupt-user-accounts-MacOS/#For_El_Capitan _ andmacOS

Is there another way to reset the permissions of the user and the default ACLs on macOS Sierra?

If you are looking for in the forums on the topic and limit to messages by Linc Davis, he posted a script that will reset everything.

How to set ACLs for a volume?

Hello

I'm sharing installation points on my external hard drive (in El Capitan Server) and he said:

"Failed to save the access control list. Make sure that the access control lists are enabled on the volume. »

There used to be a way to do it from the server application.

Can any tell me how to proceed?

Thank you!

A few things to look at.

First of all, if it is a new drive, you reformat to make sure it is formatted in HFS +? Some external drives are preformatted with alternative formats of partition. For example, if the drive is formatted in FAT I think not that he supports the ACL.

Then, if the drive is formatted in HFS +, there is a chance that your player is set to ignore permissions. Select the drive in the Finder and information. Reveal the section sharing and permissions of the window read the information. Check the status of the 'ignore property on the Volume' and make sure it is not checked.

Also, I suggest that you do not share an entire drive. Instead, create a folder on the root of the drive and then created folders within the folder. The reason is that the root of the disc contains a number of hidden files that have specific uses. For example. Spotlight is to search for and .fsevents for file system events. You don't want mess you with permissions on these hidden folders.

Reid

Apple Consultants Network

Author - "El Capitan Server - Foundation Services.

Author - "El Capitan Server - Collaboration & control»

Author - "El Capitan Server - Advanced Services '.

ACL work properly with 10.11.3?

I upgraded a few weeks before 10.11.3 on my server and I noticed that new files created from client computers (actions) are now owned by the creator instead of the group. They user is not yet listed in the ACL is only the group. In fact for other users cannot delete the files that must be deleted.

I use the server to change the permissions using the ACL and that worked great, but after the upgrade, it's just like using the Finder to change (POSIX) permissions when I used to have all the problems.

Y at - it something I am doing wrong? or something that has allowed?

Thanks for any help.

I've noticed that new files created from client computers (actions) are now owned by the creator instead of the group.

A folder can never belong to a group.

The owner of any file/folder is always a 'user '.

Customers use AFP or SMB?

If SMB: activate ACL for the SMB shared files, run this command on the server:

sudo defaults write /Library/Preferences/SystemConfiguration/com.apple.smb.server lock - bool YES

sudo serveradmin stop smb

sudo serveradmin beginning smb

If you still have problem, please create a folder then check/post the permissions of the parent folder and it's new.

LS - lde/Path/Parent/NewFolder

LS - Parent/road/lde

Jeff

VLAN ACL M4100

Dear Sir

We want to create an access list to isolate our Wifi network invited all the other vlan.
When I do, diseapper of the other SSID of our laptops.

I applied to the access list to our direction to SVI comments in

! Description of the system "M4100 - 24 G - POE + ProSafe 24 port Gigabit L2 + Managed Switch w ith PoE +, 10.0.2.13, B1.0.1.1"
! Version of the software system "10.0.2.13".
! System Up Time "28 days 22 hours 39 minutes 58 seconds"
! Other packets QOS, IPv6, routing
! Current SNTP synchronized time: SNTP last attempt status is not successful
!
database of VLAN
VLAN 99 200-208 455-456 999
VLAN 99 name 'TEST '.
name of VLAN 200 'Clients '.
name of VLAN 201 "Telefonie.
name of VLAN 202 "guest."
name of VLAN 203 'fr '.
the name of VLAN 204 "TD."
VLAN name 205 "DMZ".
VLAN name 206 'printers '.
VLAN name 207 'media '.
VLAN 208 name 'Wireless '.
VLAN name 999 "3com".
VLAN 1 1 routing
-Other - or ITU (q)
VLAN 200 2 routing
VLAN 201 3 routing
VLAN routing 202 4
VLAN routing 5 203
VLAN routing 204 6
VLAN routing 205 7
VLAN routing 206 8
VLAN routing 9 207
VLAN routing 10 208
VLAN routing 11 455
VLAN routing 12 456
VLAN routing 99 13
output

network mgmt_vlan 203
IP http secure server
Configure
time range
default IP gateway - 10.253.255.1
level of 483f42190380e8780a9d32a3c63d31b86d6ad49b870db8306af86a9ce3e06cd9a39f66e666e86f0aaab777b0ab9fe571908247c31d904463d1a0767400f8e763 user name 'admin' password encrypted 15
level password user name "secit" encrypted 15 912ba98d721224814ea15db6dec1701819e75dfcafa635831e9eab148c105c20ba85dc61882dd47a65eb66dff6cf0005a1a2232b6957ec898cd6187c6bdbb510
line console
output
-Other - or ITU (q)

line telnet
output

ssh line
output

spanning tree bpduguard

!

IP access-list ACL_Wizard_IPv4_0
output

IP access-list Deny_Guest_Intervlan_Routing
deny ip 10.253.2.0 0.0.0.255 10.253.0.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.1.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.3.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.4.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.5.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.6.0 0.0.0.255
-Other - or ITU (q)
deny ip 10.253.2.0 0.0.0.255 10.253.7.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.8.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.9.0 0.0.0.255
deny ip 10.253.2.0 0.0.0.255 10.253.11.0 0.0.0.255
IP 10.253.2.0 allow 0.0.0.255 0.0.0.0 0.0.0.0
output

class-map correspondence ClassVoiceVLAN ipv4
game of vlan 201
output

Policy-map PolicyVoiceVLAN in
class ClassVoiceVLAN
Assign-queue 3
output

output

interface 0/1
Description "ACCESSPORTS.
participation of VLAN include 200-201
VLAN tagging 201
-Other - or ITU (q)
output

interface 0/2
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 1000000
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/3
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
participation of VLAN include 200-201 204
VLAN tagging 201
-Other - or ITU (q)
IP mtu 1500
output

interface 0/4
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/5
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 1000000
pvid VLAN 99
participation of VLAN include 99 200 - 201
-Other - or ITU (q)
VLAN tagging 201
IP mtu 1500
output

interface 0/6
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/7
VLAN 201 votes
policy - PolicyVoiceVLAN
Description "ACCESSPORTS.
pvid VLAN 203
-Other - or ITU (q)
participation of VLAN include 200-201
VLAN tagging 201
output

0/8 interface
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/9
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
-Other - or ITU (q)
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/10
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/11
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
-Other - or ITU (q)
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/12
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/13
VLAN 201 votes
policy - PolicyVoiceVLAN
-Other - or ITU (q)
bandwidth 100000
pvid VLAN 200
VLAN automatic participation 1
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/14
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
VLAN automatic participation 1
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

-Other - or ITU (q)
interface 0/15
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
VLAN automatic participation 1
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/16
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 202
VLAN automatic participation 1
participation of VLAN include 201-202
VLAN tagging 201
IP mtu 1500
output
-Other - or ITU (q)

interface 0/17
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 200
participation of VLAN include 200-201
VLAN tagging 201
IP mtu 1500
output

interface 0/18
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 203
participation of VLAN include 200-201 203
VLAN tagging 201
IP mtu 1500
-Other - or ITU (q)
output

interface 0/19
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 206
VLAN automatic participation 1
participation of VLAN include 201 206
VLAN tagging 201
IP mtu 1500
output

interface 0/20
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 999
participation of VLAN include 200-201 204-207 455-456 999
-Other - or ITU (q)
VLAN tagging 200-201 204-207 455-456
IP mtu 1500
output

interface 0/21
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
pvid VLAN 455
VLAN automatic participation 1
participation of VLAN include 200-204 455-456
VLAN tagging 200-204
IP mtu 1500
output

interface 0/22
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
-Other - or ITU (q)
switchport mode trunk
switchport trunk vlan native 456
pvid VLAN 456
VLAN automatic participation 1
participation of VLAN include 200-204 456
VLAN tagging 200-204
IP mtu 1500
output

interface 0/23
VLAN 201 votes
policy - PolicyVoiceVLAN
bandwidth 100000
switchport mode trunk
switchport trunk vlan native 456
pvid VLAN 456
participation of VLAN include 200-204 456
VLAN tagging 200-204
IP mtu 1500
output

-Other - or ITU (q)

interface 0/24
bandwidth 100000
switchport mode trunk
switchport trunk vlan native 999
pvid VLAN 999
participation of VLAN include 200-208 455-456 999
VLAN tagging 200-207 455-456
IP mtu 1500
output

interface vlan 1
Routing
DHCP IP address
output

interface vlan 200
Routing
-Other - or ITU (q)
IP 10.253.0.1 255.255.255.0
output

interface vlan 201
Routing
IP 10.253.1.1 255.255.255.0
output

interface vlan 202
Routing
IP 10.253.2.1 255.255.255.0
IP access-group Deny_Guest_Intervlan_Routing vlan 202 in
output

interface vlan 203
Routing
IP 10.253.3.1 255.255.255.0
output
-Other - or ITU (q)

interface vlan 204
Routing
IP 10.253.4.1 255.255.255.0
output

interface vlan 205
Routing
IP 10.253.5.1 255.255.255.0
output

interface vlan 206
Routing
IP 10.253.6.1 255.255.255.0
output

-Other - or ITU (q)

interface vlan 207
Routing
IP 10.253.7.1 255.255.255.0
output

interface vlan 208
Routing
IP 10.253.8.1 255.255.255.0
output

interface vlan 455
Routing
IP 10.253.255.2 255.255.255.0
output

interface vlan 456
-Other - or ITU (q)
Routing
IP 10.253.11.1 255.255.255.0
output

interface vlan 99
Routing
IP 10.253.9.1 255.255.255.0
output

IP management vlan 203
dhcp service
pool IP dhcp "Telefonie.
Rental 7 0 0
Server DNS 8.8.8.8 8.8.4.4
router by default - 10.253.1.1
Network 10.253.1.0 255.255.255.0
domain secit.be
b-node NetBIOS node type
output

-Other - or ITU (q)
pool IP dhcp "guest."
Rental 0 12 0
Server DNS 8.8.8.8 8.8.4.4
router by default - 10.253.2.1
Network 10.253.2.0 255.255.255.0
secit domain name - guest.be
b-node NetBIOS node type
output

pool IP dhcp 'media '.
Rental 0 12 0
10.253.3.2 DNS Server 8.8.4.4
router by default - 10.253.7.1
Network 10.253.7.0 255.255.255.0
secit domain name - media.be
b-node NetBIOS node type
output

pool IP dhcp "TD."
Rental 0 14 0
10.253.3.2 DNS Server 8.8.4.4
router by default - 10.253.4.1
Network 10.253.4.0 255.255.255.0
-Other - or ITU (q)
secit domain name - td.be
b-node NetBIOS node type
output

pool IP dhcp "internal."
Rental 7 0 0
10.253.3.2 DNS server
router by default - 10.253.0.1
Network 10.253.0.0 255.255.255.0
domain fixitsolutions.local
b-node NetBIOS node type
output

output

Maybe it's the DHCP packet filtering.

For help, try to add a rule to allow DHCP packets.

Example: (this is obviously NOT the exact rule to filter only the DHCP packets, but just a simple rule for the test)
```
IP access-list Deny_Guest_Intervlan_Routing
  permit udp 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 eq 67
  permit udp 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 eq 68

  deny ip 10.253.2.0 0.0.0.255 10.253.0.0 0.0.255.255

  IP 10.253.2.0 allow 0.0.0.255 0.0.0.0 0.0.0.0

output
```
If this ACL works (you can get the DHCP address), then you will need to write the ACL right, something like (this is just an example):
```
IP access-list Deny_Guest_Intervlan_Routing
  ! DHCPDISCOVER
  permit udp 0.0.0.0 0.0.0.0 eq 68 255.255.255.255 0.0.0.0 eq 67
  ! DHCPOFFER
  0.0.0.0 eq 67 255.255.255.255 0.0.0.0 eq 68
  ! DHCPINFORM
  permit udp 10.253.2.0 0.0.0.255 eq 68 255.255.255.255 0.0.0.0 eq 67
  ! DHCPACK
  0.0.0.0 eq 68
  permit udp 10.253.2.0 0.0.0.255 eq 67 255.255.255.255 0.0.0.0 eq 68
  ! Internal traffic

  deny ip 10.253.2.0 0.0.0.255 10.253.0.0 0.0.255.255
  ! Internet traffic

  IP 10.253.2.0 allow 0.0.0.255 0.0.0.0 0.0.0.0

output
```

Does anyone know if the ACL of HP2011 series widescreen has speakers?

The screen wide ACL of HP2011 series have speakers?

Hello

I believe that the link above shows wrong information on the speakers. Please use the following manual to check again (#15 page) because there are few models for the complete series:

http://h10032.www1.HP.com/CTG/manual/c03351672.PDF

It seems that some models have output for speakers, not integrated as mentioned in page #2:

External USB speakers amplified with audio cable supplied (some models)

Kind regards.

WLAN Access Denied for active MAC address in the ACL

I have a pretty great list ACL (Access Control) and I've never had a problem with it in the past, but I just got a new laptop and same computer when I save the MAC address and reboot the router I always get the "WLAN Access Denied" error for access from your laptop.

I did all the "sanity checks" to ensure that the password is correct and that other devices still work.

I had the MAC address of the laptop the same way, I always have, I see the MAC address in the Logs in the access denied message and copy it from there, in the access list. I did it with more than 20 other devices successfully, I'm not sure what is different about this one MAC address... I confirm through ipconfig on the laptop that the MAC address I use is correct.

When I turn off ACL, I can connect without any problem of the laptop.

Any thoughts? I am very familiar with computers and you can do an advanced troubleshooting, I do not know infrastructure and networks of the stuff so I don't know where to start here.

Any ideas on how I can fix this would be appreciated!

You may have hit a limit of the ACL. A test, remove a device from your list and see if your laptop will connect. This would confirm if you have contributed the most to list ACL on the router...

Help! ACL MASSIVE corruption

It seemed to me have made a colossal mistake to set up my iMac.

I split the drive HARD internal into two partitions: OS X = P1 P2 10.10.5, = OS X 10.7.5. All updates applied

Here is was I think I was wrong:

I installed OS X Server 5 on the partition of Yosemite, AND OS X Server Lion on the Partition of Lion. I did this, so I could do some tests with server on both systems.

Everything worked well and I was able to switch between the two partitions, testing various settings, including VPNS.

However, last week, after doing some work in Lion, when I rebooted in Yosemite, I've was besieged with ACL errors and messages 'cannot access Library.

I ran disk utility, and it seems that ALL the files on the system got error unexpected 'ACL '. By clicking 'Fix' did nothing to solve the problem.

Displaying information about any file showed several redundant entries sharing and permissions, WHICH are set to = read-only privilege.

I tried to delete or modify privileges manually, but I'm not able to modify privileges even after my admin id and password.

I tried to use the terminal to remove the ACL (all 10.10), but who have not (I can't get the correct syntax).

I thought that the problem probably occurred when I was in the score of Lion, then tried to restart in Lion and Lion is now completely locked as well. Reboot is stuck on the gray screen with the small wheel (3 days).

Then I tried to restart in Yosemite, and he is so stuck on the gray screen and the spinning wheel.

I would try to remove the ACL again using Terminal Server after restarting in the score of 10.10 recovery, but need help with the syntax for the elimination of the ACL in the partition.

i.e.

The Yosemite drive name is "HD iMac 27.

After the launch of Terminal I would enter orders
1. CD /volumes/ "HD iMac 27.
2. chmod n r "HD iMac 27.
This will remove the ACL settings for all files on the partition successfully?

I enclose a link to a screenshot of 'ls - el' and 'ls - al' orders on the partition, if it can help to diagnosis:

https://www.dropbox.com/SC/lzrlmb4ttmq9gux/AADR8wsWQNqFoOtF8elTJZUva

Any help, suggestions or precautions would be greatly appreciated

TIA

BTW - as a last resort, I tried to reinstall the Yosemite, but Setup won't work either. I hope that if I can remove the ACL I can complete the reinstallation.

Yes, something to add a bunch of ACL permissions where they shouldn't be. This:

sudo chmod-r n "/ Volumes/iMac 27 inch HD.

should remove them.

C.

LRT224 DMZ ACL

Hello

I have a bit of a strange situation that I can't actually know. It's probably something I'm on, that I'm usually on enterprise-class

My current situation:
1. WAN1 with an external static IP address.
2. LAN1 switches in pool addressing of class a.
3. DMZ connected to the addressing of class B pool (/ 29 subnet)
Port forwarding pushes some ports to our Exchange/Intranet site on class A.

Port translation pushes a TCP port that is customized to a specific machine in class B.

Class B cannot access class A, the opposite is not true. This is normal.

Class can access the internet, a specific class B machine cannot. This is false.

How I configure my ACL:

DENY all traffic to DMZ port. subnet class B source, destination one subnet of class.

ALLOW all traffic on the DMZ, source ANY, internet destination port.

ALLOW all traffic on port WAN1, subnet of class B source, destination ANY,

ALLOW TCP port custom port WAN1, source ANY, a specific destination IP address in the class B (DMZ).

ALLOW all traffic on the LAN, ANY source, ANY destination port.

DENY all traffic on the DMZ port, source ANY, a class of destination subnet.

Furthermore, and I noticed in fact just that, why it's split between WAN and WAN1? Could be the problem?

As I know the DMZ does not work the way you use. Isn't the range of private IP addresses to public IP addresses for your servers to use instead of a range of IP addresses. The DMZ LRT is different from other standard model of the DMZ.

https://community.Linksys.com/T5/Linksys-small-business/LRT214-LRT224-DMZ-basic-configuration/m-p/85...

Admin removed the rights to the list of access (ACL) HDD control how get that back?

I was working on my computer and tries to limit access to a hard drive installed in the computer (this isn't the reader operation re-allocated is on, is a completely separate disk) it is still visible but unaccessable. I deleted some of the groups and users for the reader and lost access to the hard drive completely.

I did a search online and found that I could connect to the hidden administrator account to allow more users in the account. In doing so, I managed to remove access to the account if the administrator account.

Is there anyway that I can regain access to this hard drive? Or is everything is lost. I have been working on this for hours now and have scoured the internet looking for solutions. I even tried to download the MS ACL repair utility which does not seem to do much good either.

1 log on as administrator
2. right click on the drive (say D:\)
3. Select Security tab
4. click on the button to change
5. Add users & administrators
6 grant permissions of access 'Total control' or 'Modify' according to your needs
7. click on apply button, then click on the OK button.

RVS4000, port forwarding - with - IP-based ACL

G ' Day!

I want to know if it is possible to enable port forwarding and paste an IP based ACL on the attacker.

Scenario:

I replaced my gateway linux with a RVS4000 and reinstalled my linux machine as a file server with sshd running (now residing on my network behind the RVS4000).

I have forwarded port 22 on the RVS4000 on my linux server - it works as expected. Now I want to restrict which IP addresses which may connect to port 22, that I can't go to work.

After I forward port 22 to the linux server I can't control it with IP based ACL. Even if I deny all traffic to port 22, it will leave borrowing at the server linux as long as the port is active.

I am doing something wrong or if this isn't just intended to work the way I want?

acl based port will not work with the port forwarding on the device. Once you transfer the port are all allowede to enter this port. the acl will not take effect. I think that what you want to do the port binding is not a feature of this device.

Word 2007 your AutoCorrect, MSO1033.acl, file could not be saved. The file may be read-only, or you do not have permission to modify the file.

To get this message when opening Word 2007.

Your AutoCorrect file, (Japanese weird character? with) MSO1033.acl, could not be saved. The file may be read-only, or you do not have permission to modify the file.

ALSO when I try to close or save a Word 2007 I get this message:

Word cannot save or create this file. Make sure that the disk you want to save the file on is not full, write-protected, or damaged. (C:\Program Files\... Normal.dotm)

I then click on Cancel to not save the changes and then get the following message appears:

Changes have been made that affect the model overall, Normal. You want to save these changes?

I click No. in addition to this I'm currently not able to print from word 2007 older that I created a few months before this problem started

I studied that went through all the troubleshooting steps suggested Microsoft to resolve this issue, but have had no luck... any other help or suggestions would be appreciated. I'm not

Thank you!!
Frustrated in minutes

Install the fixit from article KB2258121 (fixit #50461).

Although this problem is not mentioned in the KB problem, the fixit indeed solves this problem.

ACLs on files is not good

my computer toshiba satellite laptop has frozen while I was doing something I couldn't do anything, so I turned it off now it will not turn back. It's all right to startup repair but said it cannot automatically fix problem signature bed 6.1.7600.16385 and look further, I see that the cause is that ACLs on the files C:\windows\system32\ieui.dll are not good

Help?

Hi markle2,

· We provide the complete error message you receive.

· Have you activated the copy of windows vista installed?

1. you can try to boot to the desktop via the Mode last known good Configuration (Advanced) that could solve this problem. Follow the link below to boot to the desktop using the last known good Configuration (Advanced). http://Windows.Microsoft.com/en-us/Windows-Vista/using-last-known-good-configuration

2 run the DVD Windows system restore

Restore the system to the date it was working fine the windows recovery mode

a. put the Windows installation disc in the disc drive, and then start the computer.

b. press a key when you are prompted.

c. Select a language, a time, a currency, a keyboard or an input method, and then click Next.

d. ClickRepair your computer.

e. click the operating system you want to repair, and then click Next.

f. in theSystem Recovery Options dialog box, click System Restore

Link, please visit:

System Restore: frequently asked questions:http://windows.microsoft.com/en-us/windows-vista/System-Restore-frequently-asked-questions

With regard to:

Samhrutha G S - Microsoft technical support.

Visit our Microsoft answers feedback Forum and let us know what you think.

Basic ACL - PowerConnect 6224

Interfaces:
G1 = Internet
G3, g4 = Server (1 GAL)

G1 has no bound ACL

I'm trying to bind ACL (s) to 1 SHIFT that will allow a specific Internet traffic-> server and all (later, restrict) the server-> Internet traffic
(because it is linked to the GAL, as opposed to g1, ACL is applied to the "out" direction)
(to simplify things I use src/dest all - but later restricted to the IP addresses of the server)

My rules:

access-list webau permit tcp any any eq 22
access-list webau permit tcp any any eq http
access-list webau permit tcp any any eq 443
access-list webau permit tcp any any eq 3389
access-list webau permit tcp any any eq 1935

Binding of the ACL:

interface port-channel 1
IP access-group out webau

This allowed successfully than traffic from Internet-> server on TCP port numbers specified - well.

However, the server is unable to get out to the Internet at all.
(for example, ping, telnet google.com 80)

I would have thought with no ACLs in, we could deduct all the traffic of the LAG to the switch.

I also tried:
access-list permit Allowall each
interface port-channel 1
IP access-group Allowall in

In addition, if I have add the rule to the ACL webau (related to out LAG1):
Allow Access-list icmp a whole webau

I can ping the server-> Internet

or...
access-list webau permit each

Server-> Internet is OK

Finally - any recommendation on whether to apply to ports/channel of the server, with OUT management (as I am) vs apply to the Internet port with direction IN

Thank you!
Nick

ACL vs(or along) dotx1 - hierarchy/priority/configurability?

Hello

is it possible to have both dot1x & ACL on the same port?

and who goes first?

an ACL would allow a (begging without dot1) MAC on a port "dot1x port-control on mac?

Best regards

It is best to think of these two characteristics in the independent work of another, completely separate. The ACL will inspect packages and apply the rules to permit/deny regardless of whether the client is authenticated or not.

You can kind of think of it as two bodyguards for a building. Say your ACL is penetration, this would be your first bodyguard. If your bodyguard lists ACL, it allows you to. But there is now a second bodyguard dot1x for the second set of doors. To get the body guard of dot1x, you need the correct password, if you do not have the correct password, you will not get in the building.

Command of the force authorized would be the way to define an interface do not go through the process of authentication and verification. Or have MAB located on the port and have the clients MAC address stored on the RADIUS server.

ACL to DRAC 5

Similar Questions

Maybe you are looking for