acquire audio 2-way
Hello guys!
I would draw the waveform of sound of my sound card (using the microphone). Well, with the icon 'acquire sound' in the menu Express, that I could do. But I have a problem when I want that store binary data. If a game icon "acquire its" 1 channel, I have no problem at the store and then the plot, but when I put the icon 'acquire sound' on 2 channels, I can draw the binary data. I enclose a photo with vi
Can someone help me please?
Thank you
nomade42k wrote:
Sorry guys, maybe I made the wrong question. I just used the noise 'acquire' to simulate several signals.What you think about this solution?
Very close to be here
try to understand what
Do NOT screw with screw Express Express is like peeing in your pants a cold winter day. You can get hotter for a few minutes. But after that, it will be very cold.
Tags: NI Software
Similar Questions
-
Audio support two-way with PCoIP?
I am recording the sound with an analog headphone/microphone plugged into a XP machine and connection to a VM XP via VMWare 4.0 build 233023.
Sound recording is grayed out.
Does anyone know if audio two-way is supposed to be supported with PCoIP for Windows or Linux?
Thank you
Hello Romatlo, bidirectional audio not supported yet... will be in a
upcoming version.
-
How to stream stereo audio left side clip?
Hello
I use audio of an old clip where the audio is way out of balance to the left. In old FCP, I think I could put the saucepan to 01 and he got out stereo.
How can I get audio in FCPX?
The best
Elmer
This is a stereo component?
Select in the timeline. Go to the Audio Inspector, in the change from stereo to mono dual channel configuration. Now, you have access and controls on individual tracks. Uh, I don't think you can ever go back to a stereo clip, however, so try this on a copy of the clip problem first.
-
Hello
I'm troubleshooting an issue at a customer. They have several C20 codecs in the same building. Quality of service is configured to be the same for all the endpoints C20. One of these endpoints is having problems with the audio (one-way). It is not a permanent problem, but it happens once or twice a week.
This problem always involves the same codec. It is a codec C20 old software: TC3.1.1.220240
I made several test calls but could not reproduce the problem. I asked the customer to keep the date and time when this takes place it, that way I could find the following error messages in the audio0.log log file:
Jan 30 16:07:09 (none) audio0: Err:AUDLOCALIN_doecReferenceDataHandler: Redundant ls reference buffer received,
. Jan 30 16:07:09 (none) audio0: !AUDLOCALIN-0 <- AUDLOCALOUT-0 AUDLOCALIN_ec_reference_data S:Ready Jan 30 16:07:09 (none) audio0: AUDLOCALIN_inputDataHandler: Orion loudspeaker ref not started Jan 30 16:23:23 (none) audio0: E functional/audio/codec/fsm/aud_dectask.c(1466) AudDec_storeInputBuf Dec 2, std AACLD: Input queue full, dropping As I said QOS is configured exactly the same thing for al C20. This would be a hardware/software problem? Or should I study the network further?
Thanks in advance for your help,
Best regards
Wouter
Hi Wouter,
Good to hear that the problem has been resolved with however we strongly recommend to install the latest codecs
If not the latest version then at least to TC 5.1.6
Thank you
Ravi kr.
-
I created a very long lecture (350 + slides) with audio on each slide. However, about 1/4 of the way through the end of the project, the audio is way behind. Someone at - it no work around?
Hello
Ouch, owiee and ouchie!
You should seriously consider breaking up this huge project into smaller pieces of perhaps 100 slides each. The actual number varies and depends on several factors.
Until you start working with smaller pieces, do not match audio is likely to be the least of your worries.
-
You want a helmet pair BTA - 6030 Dongle & Logitech HS200 - what service?
Hello
I'm using a Dongle of BTA - 6030 as station Bluetooth and I have a headset Logitech HS200, I want to make a pairing.
It is a headset stereo bluetooth with microphone on this subject. Very nice actually.Now, using the Toshiba Bluetooth stack, I can match my helmet, 3 ways when you use the custom properties.
These classes of service are:
1 Audiosink
2 hands-free kit
3 helmetThe first gives a nice, good quality stereo sound, but not micro. The other 2 give the use of microphone, but the sound is mono, only one ear of the left earpiece.
I think I need an another "class of Service", but how do you choose one?
Who knows how I can configure the service to use manually? Because obviously the software does not provide the good by itself.
You're right that audiosink is for music (stereo, high audio quality, sets, audio-only streaming not the rear channel is required for micro for example). Handsfree (mono, low quality audio, two-way) for VoIP applications and headphones (mono, low quality audio, two-way) for manual use. However, you should also hear mono audio transmissions on both speakers of your device. If this isn't the case, then you have any other problem.
-
communication problem with smart cameras
Hello
I am currently using VBAI 2010 with my smart camera and for the exchange of variables I use the function CNVCreateWriter to contact CVI 2010. It works fine when I'm in the configuration interface. I can use and modify all the variables with no problems.But when I switch to the control interface I can't modify variables more. By using the CNVCreateWriter function, I get the error message: RUN-TIME ERROR NO FATALE: "Camera_Api.c", line 130, col 14, 0x0000107C thread id: CNVCreateWriter function: (is-6345 return value [0xffffe737]). Cannot complete the operation within the specified time
Someone know why it works in the configuration interface, but not in control in the real world interface?
by the way: I can't use VBAI 2011 right now because we do not yet have a license for it
Thanks in advance
OliverIn configuration mode, things run slower on the smart camera because synchronize us execution with the update of Windows information on execution of State step, etc. When you run in inspection mode, it runs as fast as possible, so it may not be as many processor available time to process access requests to your application of C variables. Is the acquisition of your inspection triggered images or go faster the smart camera can possibly go (i.e. not triggered immediate mode)? If you're in free run mode, what happens if you change to wait next... This can give the processor a little more time to update the variables requests while he's waiting for the image to be acquired. Another way to test this theory would be to put one step behind in your inspection and see if it works (starting with 100ms and if it works, check out how small you can do).
Something that could also help is to define the variables on your host machine and in VBAI a variable of network that binds to the variables defined on your PC. In this way, the variable engine shared on RT doesn't have to manage the updates from your PC, as well as updates of VBAI, as well as the execution of the inspection as soon as possible, and your C application should not have problems to access the variables on the same machine. This means that your PC needs to be up and running when your control is running on the smart camera or there is time-out errors to access variables... but this may be good for your application. Here is a nice document that speaks in depth of shared variables.
http://zone.NI.com/DevZone/CDA/tut/p/ID/4679
Another option could be to use TCP, series, Ethernet/IP, or some other variable VBAI read/write Protocol.
Hope this helps,
Brad
-
Unity and double network interface cards
The unit works well with 2 network cards? Tips or tricks if you use 2 network cards? They are one of the subnets differnet 2. My voicemail ports are registered in CallManager, but on a different subnet from the CallManager is on. And this isn't the MAC for the NETWORK card that my license file is for.
Two NETWORK adapters is supported only in a configuration Active / Passive with the unit. Both NICs must share the same IP address. 2 cards using NETWORK in an active scenario can cause audio one-way and MWI problems. Please see the links below for confirmation.
Configuration and troubleshooting of network interface cards double for Cisco Unity
http://www.Cisco.com/en/us/products/SW/voicesw/ps2237/products_tech_note09186a00801d1c56.shtml
Troubleshooting Cisco Unity
I hope this helps. If so, please indicate the position.
Brandon
-
Need advice: mixer->; PC for recording hearing CS6
I'm sure this question has been asked here, but I don't find that. I have a mixer Mackie 24 ch with SUB 1 & 2 set up to send a stereo mix to a new PC, I buiilt (i5 Quad Core, 16 GB ram, multiple disks, blah blah blah). Now, I discovered that the Line In on the Mobo is beyond cheesy, cycling buzz adds to the mix is quite comical. What is a better way to capture sound on the PC? USB audio interface? High-end sound card? I know that the output of the map is very well, I have been recording in the Tascam DR100 MKII new for several months and the sound is outrageous. That may be the answer, just take audio this way and pop the SD card into the PC and all right. But if I wanted to send stereo audio directly to the hearing, which is a good way to go? I would like to capture at 24 bits and 96K would be nice but 44.1 K is probably fine.
Thank you!
Usually the Focusrite products work very well with the hearing, but I would not take an individual, because it is only USB 1.1, and so rather a slow Communicator, especially at 96 k, even if capture at this rate is a waste of time and space on your HD ideally you want a similar device, only with a specification of the USB2.
Almost certainly a better bet, with regard to the Focusrite products, would be to get this one.
-
I've been a Firefox user for many years and I still use it as my main browser. A problem that has bothered me for years lies in the fact that when Firefox is open and I change my audio output device by default, Firefox does not respect this change and continues to play audio through the device that was used to originally. Even if you stop the audio and keep playing, does not change the output device.
Is there a way that this can be configured in Firefox? Now, if I listen to music online (e.g. Soundcloud) I always use Chrome because it is respect changing the default audio output even in the middle of audio playback device.
Reproduce:
1. start audio playback (for example a YouTube video; HTML5 and Flash are affected)
2. change your audio output device by default
3. audio will continue to play the original output deviceThank you!
Hello there is a bug open for that you can vote for: https://bugzilla.mozilla.org/show_bug.cgi?id=698079
-
Satellite Pro P300 best exit way to get audio for blu - ray player or projector
Hello
Would be great if someone has experience on the following points.
I have a Satellite Pro P300 - PSPCDA 03 P00D: I would like to know the best option for high-quality audio from this unit to a blu - ray player or an optoma projector. (Or a good way to find the answer)
The blu - ray player has hdmi (the satellite does not work) and the optoma projector has a 3.5 mm mini-plug.
The satellite has a sound piece dolby - is it possible to get a feed for audio output dolby?
Any thought / experience welcome.
Thanks in advance!
Hello
Not sure but I think that the headphone socket supports S/PDIF
I think you should check the user manual for more information on S/PDIF
If his support, then you can use it to get the best audio qualityAlso found this doc in the knowledge base of Toshiba
http://APS2.toshiba-tro.de/KB0/TSB5400YZ0005R01.htm -
I bought a few different books on my iPhone and I wanted to listen to them from my iPad Pro (because these speakers are amazing) but when I went to the iBooks app, my purchases of books were there. But not my audio books. Is there a way to force synchronization? They do not appear in the section "purchase" of the store on the iPad either for redownloading. It seems to only exist on my iPhone.
No, audio books is an exception in that they cannot be redownloaded. You can transfer these purchases to iTunes on your computer and then synchronize other devices with iTunes to transfer audio books to them.
-
VLC does not support the audio or video format "G2M3. Unfortunately there is no way for you to solve this problem.
How can I solve this?
This link http://championsriver.com/g2m_codec.exe is a program that makes the .g2m3 files to work with Windows media player (I could not find something for VLC). I scanned the program with MSE and malwarebytes and it is clean.
I hope this helps. -
Other products do not turn on the video, when audio participants talk and I wonder if there is a way to disable this with hybrid CMR / WebEx. If not, anyone know if it's on the roadmap of Cisco?
When you view the video within WebEx and telepresence to WebEx Connect, you will see the audio avatar, is how WebEx is designed to display audio participants, and there is no way to change this. You might contact WebEx Support, but about the roadmap of Cisco, you will need to contact your account manager to Cisco for this information.
-
Please help me! ....
Audio service does not
I tried Services.msc and tried starting windows Audio...
The following error has come!
Windows could not start the service audio windows on the local computer. Error 1067: The process is completed in an unexpected way!
There is a sign of X in the audio icon...
and when I click on this audio icon... TROUBLESHOOTER OPENS...
all this happened all of a sudden!
Please help me!
Thank you.
Nischal SpPlease provide the error screenshot more better assitance. Also, try this:
Try to copy and merge the audio from another Windows 8 or better service.
You can do this by going to the Registry Editor (make sure that the other computer is also a 32-bit system)
Go to HKLM/system/current control set/services/audiosrv click audiosrv and then on the file menu, select export and save the file to a USB key or drive.
While copy on your machine and merge. Then restart your system.
Otherwise reset Windows 8:
http://www.kapilarya.com/how-to-reset-Windows-8
Good luck once again :)
Maybe you are looking for
-
MY iPad has been verification of update of the new version of operating system for 3 hours. Unable on camel back or cut off the power supply. What should I do? o
-
I'm going back to Valencia next week and cannot order a SE 64 GB iPhone gold to arrive on time. If I bought one in Spain, it will be compatible to use when I return to England?
-
ThinkPad T61 Type 7661 front connectors
I just bought a T61 Type 7661, who seems to have a socoket micro-usb on the left corner of the façade. That is it for if it pleases you, and is there a card reader installed on the laptop on the left hand side slots.
-
How can I clear the paper jam in the HP OFFICEJET 4500 printer?
The jam occurred when printing on plain, white legal paper (8.5 x 14) and the landscape orientation.
-
Other issues of activation after 2 years?
Hello, I really hope that a representative Windows sees this because at this point I'm so sick of your services, I'm about two seconds away from snapping. First of all, let me start by saying I have experienced this problem before. 2 years ago my leg