ACS1113 services of gradient.

Similar Questions

• PowerEdge T310 Hard Drives die!

  I was wondering if anyone else has experienced this problem or something similar:

  We have about 100 of T310 in production running with RAID configuration mirrored (Hyper-V Server 2008 R2 hosts - they are obviously not 2012 because this RAID "Controller" does not support the server 2012 and will never be according to a Dell representative with whom I spoke). This is the RAID software built into the BIOS (PERC S100 I think) or whatever for Windows (not sure if it works with other OS?). I'm certainly not an expert on this particular RAID "Controller", but I'm having a bad experience with it or with hard drives that provides Dell. Now until someone enters the speech 'you get what you pay for', I am quite aware of this, especially at this time. Here is the situation that we face. We have 2 servers at each of our branches, and each server has 2 discs. That's a total of about 200 hard drives. Currently, 50 of these 200 readers are omitted. Normally, I would not worry. See, the subject of a RAID is used to provide tolerance of the redundancy and fault when one (or more) disk fails. Then... I should be able to just stop the server, pop another drive, hop on Dell Server Admin and rebuild the RAID, right? NOPE! Here are the results of the last 6 attempts of service with gradient records machines:

  3 servers never started upward after be closed (two physical disks mirrored in a failed State)
  3 servers booted up back but the RAID rebuild failed because of too many errors on the remaining drive

  Now, these servers are not THAT old. In fact, some of those who have placed disks have in production since a little over a year. It does not matter if there is dust in the computer; We had total failure on machines with ZERO dust inside or on the readers. Supplier of readers also doesn't seem like some are Seagate and Western Digital are of importance. Now, I do speak not only on disks that has been corrupted and could be reformatted. I mean they stop actually spinning (think click of death most of the time). Embarrassing enough, I have to admit there are a few cases where I could slap a sense in them (literally - yes I actually physically struck against a hard surface readers and they have began to turn again, at least enough to recover virtual machines).

  Now, I went to the bottom of the avenue to try to set up alerts via Server Admin but I noticed that, in our case, the events in the log do not always indicate the drive failure and don't seem to even not always detect the degraded state of the virtual disk (actually, a failed drive is often reported as being in a "ready" State) ", apparently thrown out of the RAID as a renounced child). This means I can't rely on that as a solution. But, well, that's all beside the point... We decided to replace the drives in servers with a single solid state (System of the pair of two servers at each location actually provide redundancy anyway and we were to replace servers at locations where both servers have degraded virtual disks to prevent total failure). No RAID means that we can at least go ahead with Server 2012 and get out a few more years of life of our T310.

  I recognize and I probably shouldn't be, that we have absolutely not been diligent to keep the firmware up-to-date (Yes, SHAME ON US, I know...)

  Anyway, enough with my history of sobbing and my expert "data medico-techniques"... sharing I'm just curious to know if anyone else has had negative experiences similar to mine. I might also note that we had problems of disk failure with a lot of recent desktop models that use the same drives that come with the T310. I thought it also interesting that we have a couple of T110 out there who are both much older than that of the T310 and have never had a disk failure (keeping my fingers crossed). It's just a shame that we have a few desktop computers (Dimension 3000) who worked for 7 years with their original hard disks and in general, we get no more than 1-2 (maybe 3) years with the things they've been giving us lately. They just don't make em like they did I guess! Anyway, thanks in advance for your time!

  > if anyone else has had negative experiences similar to mine

  As a TECHNOLOGY company, we ended up with two T310s in the field before we realized what the S in front of the model number.  A PERC, a software controller had never been in the past, and we didn't expect the default controller for a small business server with SAS 15 K of Dell discs would be.  Of the two, the two had a drive replaced in their bays.  The servers were under warranty, all two S300 controllers and both have been only less than two years.  When talking with Dell technicians, they were very skeptical that readers actually had a problem.  Before we did anything, they wanted the drivers and firmware for controllers and disks up to date.  Then after several attempts, they decided to try a car and if it does not, try a controller.  Is not big thing to inspire confidence.  If you read the questions, you will be fine is based their concern about the false reports.

  The next issue focuses on hard drives.  It's easy.  This is because the readers never get a rest.  Unlike with a hardware controller, the drives are insanely busy all the time.  Give up the collar and watch.

  Another problem is the only work of S controllers with Windows.  This may look like a small point, that this is not the case.  This means that backup software top of range such as ShadowProtect, IMPOSSIBLE to restore your system in case of failure, only the Microsoft Windows backups can.  Fear that you get the idea that you could do with Windows PE, I have news for you, it does not work.  They have no drivers that will load with it.  Dell has no apologies for the S controller if you enter in this situation.  It also means that many partitioning utilities do not work because most are? nix based.  In addition, recovery tools do not work for the same reason.

  I hope to spend the first of our T310s in the field in a H700 this weekend, and another after the tax season for another client who does not know yet what is to come.

• "GRADIENT ARRAY" message on my Qosmio G20

  Hello world

  I have a qosmio g20 and for some reason when I start the following message is displayed:
  DEGRADES in TABLE-1.

  I have all tried allmost, uninstall the raid utility, formatting the discs, but I still get the same message.
  Also, I get the same message when I try two mirror disks. When you get to 90% of the mirroring of an alert is displayed again indicating "table 1 gradient, a drive is missing.

  Hope someone can help me.

  Thank you very much
  Kozach75

  Hello Kozach75

  This message appears if the RAID controller detects a problem with the HARD drive. On this path, it is not possible to say why this is happening, but there may be a serious hardware problem. Please contact the Service partner and let check the device. G20 is a new unit and the warranty will cover all costs.

  Check this page http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true.

  Good luck!

• Problems of ACS1113 SE & IP

  people

  thought I would let you know everything a problem I encountered with an ACS1113 SE sit in a DMZ Firewall 4.1

  I had problems of connectivity with the box and had to go on-site and console on it

  only to find, he had lost his IP address

  I've reconfigured the address manually, but despite tell me the config has been saved and displays the new IP address once the services have been restarted the address disappeared

  Happened 10 to 12 times, until I had to configure the firewall to act as a dhcp server with a scope to a single address

  the ACS took address no problem and works correctly since

  someone at - he seen this before?

  Hello

  Make sure that ethernet is connected to the low NIC of the ACS and then try to assign a static ip address.

  If you run ACS SE 4.1.1 build 23 then it is a defect of

  Path: http://www.cisco.com/cgi-bin/tablebuild.pl/acs-soleng-3des

  Patch filename *: applACS - 4.1 - set - ip -CSCsm73656- patch_to_603_r40_lc.zip*

  Read me and displays instructions:

  applACS - 4.1 - set - ip -CSCsm73656- Readme.txt

  HTH

  Kind regards

  JK

• gradient

  Hello

  In first 10 items, you can create a matte black or even change to any solid color on the spectrum.  However I'm not interested in creating a gradient.  is it possible in the first.  You see this as a common background for cable news shows, and that's what I'm trying to simulate.  Multiple colors which are animated I they shift and change gradually to shades.  Like if this is feasible.

  Here's something I found on youtube to show visually that I am talking but looking to create directly on the front is more customizable:

  https://www.YouTube.com/watch?v=wpK1B5WfhIc

  adobenewbie123

  I will outline my plan which is in the slow progress that I create as I go.

  1. with the help of the Premiere Elements split concept mattes and color screen and cropping effect, create of multiple vertical panels on the screen.

  This is the easiest part. That actually got.

  2 then keyframe the Position property of each of the panels.

  3. apply strategic between Fuzzy Panel.

  Once you have the simple, pretty easy to change shades of signs (color covers). It is the choreography of the creation of keyframes for the movement of Panel which takes time and concentration with coordination.

  When I mentioned using stock footage instead of doing it yourself approach, I was referring to the sites that offer these types of files as a service (most of the time with a price for what file do you want). Using the images from YouTube and edit can get complicated for protected content and the YouTube license agreement.

  I would like to know if you want me to continue in the choreography of keyframing described panels.

  Thank you.

  RTA

• How to use ps to create a file with color gradient png

  I want to design a texture (png file) for a light in 3ds Max. I wish the texture reduce the alpha gradually from top to bottom (from 255 to 0).

  And then I'll see the tear of light will become pure transparency in 3ds Max.

  Could someone knows how to create texture (png file)?

  Attach file is my psd file.

  Hello

  Just follow the steps below.

  1. create a new transparent document.

  2. create a gradient in the gradient panel.

  3. click on Ctrl + S or Ctrl + Shift + S to save and choose the format ".png" file format option

  (If you want to create a transparent gradient then see attached screenshot settings)

  Hope this helps,

  See you soon

  ------------------

  Sindou Puri

  LeXolution IT services as

• No service after upgrade the server to 5.2 on El Capitan

  I have a web server that was doing very well until I left the 5.2 update suggested to install OS X Server. I can't get to broadcast web pages. Screen sharing works always and nothing has changed on the routers, etc.

  I restarted the server after the update and restarted the server itself several times but keep getting connection via a browser failures.

  I did the upgrade even on other servers as well as the upgrade of Sierra. This server is running El Capitan, and is the only one that gave me problems. 5.2 server is not compatible with El Capitan?

  Some additional info:

  I can connect to the server through ftp and other services; just no web service.

  Port tests show that port 80 is not blocked

  Using the IP address I can get to the window of the home server.

  Accessibility means no services available

  Websites is on and I can't find anything that is not defined in law or is different than before the update.

• 6 ios10.0.2 iPhone no service/network?

  IPhone 6

  IOS 10.0.2

  16GB

  After that I updated the version of iOS to the latest version from 9 to 10 and 10.0.2 I couldn't get any service in the phone

  no service

  No network

  I tried all the solutions, but did not successfully

  pls help

  Ymah995 wrote:

  IPhone 6

  IOS 10.0.2

  16GB

  After that I updated the version of iOS to the latest version from 9 to 10 and 10.0.2 I couldn't get any service in the phone

  no service

  No network

  I tried all the solutions, but did not successfully

  pls help

  If you do not have cellular service on your phone, then you contact your phone provider and let them know that you can't get their service on your phone.

• Poor - and not yet no answer customer service!

  Hello!

  My apologies for the weird subject but heading I really wanted to attract someone's attention because at the present time (a guy called Paul online support side) nobody came back to me at all about my recent visit to your store from Covent Garden and the very disappointing time there.

  In short if your management team he has just done what they said they'd do and return my call to discuss things further as a guy named will be very kindly suggested I do we would not be here!

  This email comes from me trying to talk to a member of the management team after my visit to Covent Garden on September 22 and the feedback left by me after my experience so far here.

  Will me has called and left a message on 30 September by inviting me to remember to discuss also I have does - no call back. So I didn't call back the next day - no call back and the next day still no call. We are now on day 5 and after talking to someone in the store who very frankly really seemed to not want to be there and really seemed not the least bit interested to help me at all I'm resigned now pretty much on the fact that I get not this call and will not in fact also discuss how some members of staff there myself and the day my wife turning what was supposed to be one of the highlights of our stay in London in one of the low points.

  I talked to a representative of the online customer service which was fantastic, although itself also agreed that realistic, my chances are slim to a call back that he was however able to seize a member of the business team that supposedly spent on the information of countless previous officials do not have in the hope of a return call We'll see if it succeeded or not - I doubt that very much.

  So I'll now emailing this email to all the world that I can at Apple, to raise awareness on the fact that your ship called the flag shop in London (while the street regent is under renovation) has not only some very few poor staffing but also issues clearly a massive communication issues. I have to wonder how the store works effectively in this management, I myself am a branch manager and would like to know of all these questions should they arise and also to know the importance of the Dodge don't no calls - or even potentially conflicting ones. Clearly here, it is not the case, and as such I have to say that I will never to set foot in this store again.

  You do not discuss Apple here. This is a user to user support site, and your long message falls on deaf ears. To inform Apple that you are disappointed by something, use their site here, http://www.apple.com/feedback comments

• My 5s iphone suddenly showed no service, then I made an attempt to update to ios and itunes connected, now iphone is not enable and display cannot connect to the server and in itunes it shows unable to check your device.please help me

  My 5s iphone suddenly showed no service, then I made an attempt to update to ios and itunes connected, now iphone is not enable and display cannot connect to the server and in itunes it shows unable to check your device.please help me

  Assuming that you have a valid SIM card in the phone, it is more often symptomatic of a phone that has been hacked or jailbroken to unlock.

  Where do you have the phone first?

• 10 iOS and ios 10.0.2. Always give service problems.

  Since ios 10.0.0 came out my phone started acting weird until I could update. Then the update made my telephone service say up to the search for a few weeks now. I have restored, downgraded, updated updated again iOS 10.0.2, reset all settings, reset settings network, restore, rebooted and even changed my sim card. My service is returned temporarily for an hour and that's all. Att says I should talk to a store of authorized local apple (not really apple) and also told me that there is nothing they can do. I was told that I should talk to someone at apple and see if it can be fixed or just replace my phone (which is not something I can afford right now).

  Help, please

  Hey there, c_thibeaux. Welcome to the communities of Apple Support!

  It seems that your iPhone iOS 10.0.2 6 is looking for service and you are unable to connect to your AT & T business network. Have you tried a litany of troubleshooting steps, and I would suggest a more.

  How to back up your iPhone, iPad and iPod touch --before troubleshooting a device, I always recommend a new backup to protect your personal information. It is preferable "to have" one to the 'need' to a backup.

  Use iTunes on your Mac or PC to restore the iPhone, iPad or iPod to factory settings - this step will completely erase hard drive and remaining needs through iTunes on a Mac or PC to your iPhone. The first time, select "set up as a new iPhone. Once you return to your home screen, you should be able to see if you connect to their service. If everything works as it should, use the "restore from backup" link in the section «Get help» If it is not, under the same article, "Contact Apple Support".

  I hope this helps!

• New location of SOS Emergency services IOS 10

  so I have updated to iOS 10 on my IP6s and research in location services, there is a rocking new emergency' sos' that means emergency services can follow you?

  Most of the phones allow you to disable the location services for 911 evolved so much, I am not sure that what the switch is for. All phones sold in the United States for the last decade (more or less) have been created so that if you call the number of the emergency services (911), dispatchers will be able to see where you are. This is why they can send the police, fire or ambulance to the correct location even if you don't know where you are.

  Edit: It's the new SOS emergency on the Apple Watch:

  On SOS on Apple Watch - Apple Support

• No Service, iPhone 7 more from AT & T

  Just the iPhone Plus 7 and it worked fine for a bout 4-5 days. Then, I used Google Maps yesterday to go to a ball game. After using Google Maps, my cell service has been abandoned and continue to see 'No. Service' on my iPhone 7 more (on AT & T in the neighborhood of Manhattan NYC, so it CERTAINLY isn't the coverage area).

  Have any other products of iPhone (iPhone 6, iPhone SE) and NO of them have coverage problems. Entered the AT & T store today and they changed the SIM card this morning but the problems persist. Apart from the usual reboot, reset network, hard reset, still getting the No Service issue. From time to time I get service him can't seem to get consistent service from the new iPhone.

  Really annoyed and even worse, is that I can't even call an Apple customer service because they need to call my phone number. How can Apple Customer Care call me when I can't even a stable connection on my phone? tried to have Apple call my work number, but it's an automated system and that doesn't seem to work.

  The guy at the store, AT & T (corporate store, no franchise) says it has been a big problem with the new iPhone last 7 days 3-4.

  "Really annoyed and even worse, is that I can't even call an Apple customer service because they need to call my phone number." How can Apple Customer Care call me when I can't even a stable connection on my phone? judge having Apple call my work number, but it's an automated system and that doesn't seem to work. »

  There are other phones in this world in addition to your iPhone. Call the Apple Service and give them another phone number, to which you have access.

• IPhone 6 + service research/no since iOS 10.

  Since I have updated to iOS 10. My cell service has been slowly getting worse and about 6 days ago. He totally exploded and never returned. Went to my cell provider and there was nothing they could do. I did every difficulty, you possibly can. My cell provider also said it has spent a lot with all Iphones. Yet, here we are almost a week later. Apple do nothing to solve this problem. Because it is not my phone by any means and is all the software.

  Hello BrettB621,

  Please ask questions on your iPhone and any service issues since iOS 10 here in Apple Support communities. I understand how it is important to have a reliable phone. I'll be happy to check it out with you.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, please visit this help article: If you can not connect to a cellular or mobile data network.

  If you still experience the same problems after the troubleshooting provided in this article above, steps please try to restore your device from a backup by using this article help: restore your iPhone, iPad or iPod touch from a backup. If you don't have a current backup, please try this help article: If you cannot update or restore your iPhone, iPad or iPod touch - Apple Support. Please pay close attention when you get to step 4 who said "when you see the option restore or put to update, choose update. iTunes will try to reinstall iOS without erasing your data. "to get your iOS reinstalled. Test if the issue is still ongoing.

  Thanks again and have a great rest of your day.

• Cannot re - install after broadcast HD, error 2203 on all services

  My problem seems to be very specific and any help on the internet seems to work

  • That's happened?

  I run my system on a SSD and install my programs on a HARD drive to keep the SSD free games. My HARD drive corrupted and had to be reinstalled. Thanks to the fact that Windows is safe in the SSD, it wasn't a problem, all I had to do was re - install the programs on the HARD drive.

  • Can't install or uninstall the previous installation

  iTunes (and apple support pack, install, bounjur, ipod etc.. services that accompany it) were not even install (option = repair) or uninstall. Always returns an error. So, I went to remove them manually:

  + Clean Windows registry from any input on iTunes and Apple

  + Deleted all files and folders

  + run Windows Install Clean Up to make sure they were all gone

  This is often all help the stopovers of the internet, so-called, I would be able to install now that the old installation is over, but...

  • Installation see more older version, even not the box install Apple update, still no luck

  Error 2203 like 4 or 5 times and ends with ' installation is impossible, no changes. " I guess the 4 or 5 times for each service, it attempts to install (Hello, updates, etc...).

  I run the installer correct version and even the old version, I got the backup (which is not this old 12.5.1.21). But it will ALWAYS FAIL WITH ERROR 2203.

  Points of view?

  10 64-bit Windows

  See the note 1 troubleshooting issues with iTunes for Windows updates. Try the Microsoft cleanup tool. Look at the rest of the tip as needed.

  TT2