ACS1121 MANAGEMENT INTERFACE

Similar Questions

• EqualLogic group member network configuration error: "management interface should not be on the san subnet.

  Hello

  We currently have new EqualLogic 6100 device with this network configuration:

  Director of the IP - 192.168.0.2 (VLAN1).

  Member network config:
  eth0 - 192.168.0.3 (VLAN1)
  eth1 - 10.10.10.3 (VLAN2)
  eth2 - 10.10.10.4 (VLAN2)
  eth3 - 10.10.10.5 (VLAN2)
  ETH4 - empty

  I would attribute 192.168.0.4 to eth4, but received the error: "management interface should not be on the san subnet.

  I am sure that all interfaces eth has access to the VLAN1 and VLAN2, mean error indicates that eth4 should not access VLAN2 and only access the VLAN1 on the switch?

  Or eth0 should also have access to the VLAN2 only to reconfigure eth0 and eth4?

  Thank you

  > The group eating IP should be in iscsi VLANS?

  Yes!

  Note: If configure you an EQL it will ask an iSCSI port because nothing is more necessary to bring it up. The doest previous EQLs have a dedicated Mgmt Port and later, you can convert the last ethX as a MGMT port. This is the reason why configure you ISCSI at the beginning. (Think of a mixed group of newer and older models, and you get a picture)

  OK... once again it is the one and only member of the Group and there is making the production host connected to the right?

  The change of IP address, to a 3rd. subnet for temporary use.

  -Do not touch eth0-3 and the IP address of the group now

  -Configure the MGMT port and IP address management in the tempr group. Subnet. Use the Config-> Adv. Group-> network MGMT. You can change the MGMT Port of the Member, and the address IP of MGMT

  -For the registration of the configuration, you will lose access. You must place your admin PC in the templ. subnet so

  -Connect to the GroupMgr with temp again. INTELLECTUAL PROPERTY

  -Now you can change the IP address of group 10.10.10..x

  -Now you can change eth0 10.10.10.2

  -At the end, you can change the address IP of the Group MANAGEMENT, as well as the MGMT Port to 192.168.0.x

  -Change the IP address of your admin PC rear

  A failover, you should consider to hang a serial cable the active controller of the EQL. Use 9600,8,1, N with your favorite terminal program (putty.exe on windows). All the steps, you can perform from the command line.

  If this group and the only member not in production, but you can reset the config and restart from the beginning.

  Kind regards

  Joerg

• Web management interface of LAN N3000

  sHello,

  We have replaced our old 62xx powerconnect with a new stack of switches N3000.  With the earlier material, there is no remote management interface. Thus, we were able to manage the passage of our LAN subnet.

  If I put interface OOB in our LAN subnet so I can't send IP to the VLAN. ... .

  How to be able to administer our N3000 switch via web gui of our LAN subnet.

  I tried to address ip configuration for vlan1 in the hope that I would be able to gui for managing web... .but not...

  Console >Activate

  Console #Configure

  Console (config) #interface vlan 1

  Console #ip 192.168.0.250 address 255.255.255.0

   

  Can you please help?
  

  Thank you for reading my post.

  Gmiga.

  recently had this problem,

  you don't need the OOB port so just set his IP and the gateway to something, that you'll ever need (or just leave no configured completely make sure you it is disconnected/disabled)

  what you were doing with the VLAN is correct, simply set the gateway:

  Console > activate

  Console #configurer

  Console (config) #interface vlan 1

  Console (Config-if) #ip address 192.168.0.250 255.255.255.0

  output console #.

  Console (config) #ip - default gateway 192.168.0.1

  by setting the default gateway, you should now be able to administer your switch to other subnets

  You may have already worked to this point, but it is good to leave it here for others.

• How to set up the AP Manager interface on vWLC

  Hello all,.

  I want to bulid a laboratory wireless env, vWLC is used, but I can't find where I could configure AP Manager interface vWLC.

  How do I creat an interface of the AP Manager?

  Thank you for your help.

  1.How many APs could this Dynamic AP Management support ?

  No limitation on the interface. It all depends on how can license AP you have on your vWLC

  2.We can't creat AP manager interface on vWLC like real WLC , right ?

  Yes, good. New platforms of controller, there is only the interface of management exist. There is no separate AP Manager interface.

   3.How can I distinguish my AP's  "Country Code"  ?

  If you look at your reference number AP (see the version should also give this), it indicates a regulatory domain (for example - A,-E, n, z). This means that your vWLC set up with a country code in this regulatory area. The document below for more details http://www.cisco.com/c/en/us/products/collateral/wireless/access-points/product_data_sheet0900aecd80537b6a.html * don't forget to rate our answers if you find them useful * HTH Rasika

• UCS management interface - B series

  Management of the UCS of series B can then passage to uplink ports / Server interconnection fabric and not on the Management Interface of the FI? As in the C series there is a choice in the MMIC where management requires ports LAN (LOM)

  Yes, since IF you have a connection of the mgmt0 port - is for the FI management and KVM blade, etc. (e.g. the OOB management).

  On the IF configure you uplink profits that are used to carry network traffic on the blades.

  On the C series if you configure the port MMIC to be mode shared-LOM then yes all traffic management and the path of data will be done by the same ports LOM. If you choose the dediacted port then you must use the MMIC port on the C series for the management and LOM for the data.

  . / Afonso

• Dynamic management of the mobile AP management interface to another dynamic interface (WLC 2504)

  Situation/configuration is the following:

  -2504 WLC (8.1.131) with a total of 22 AP is connected.

  -Several WLAN active each with its own interface (dynamic)

  -L' (static) management interface is the option "Activate the dynamic management of AP" enabled.

  -The four physical interfaces of the WLC remain TROLLING configured.

  What is the problem:

  In the current configuration, the management interface is in the same vlan as the AP we now want to move the management interface to a different VLAN, but keep the AP in the vlan current. The idea is to move the management interface to its new vlan and disable "enable dynamic management of AP". Then, create a new interface (dynamic) in the same vlan as of AP and select 'turn on the dynamic management of AP' on this interface. Configure it as it is no problem but is does not work. The AP will record is no longer with the WLC.

  Is there something I may be missing why this does not work?

  Richard.

  Yes, that's the gist of it.

  I recommend always making a capture packets if only just for educational purposes and to see how this works in action. I found it interesting when I did in the lab here.

• WLC use Management Interface & more get started Questions

  Hello

  I am yet to implement Wireless LAN in one seat of our customers. There are 40 x 1130AG LWAPP AP and WLC 4404 with ACS 4.x for authentication of Wireless Clients attempting to access the LAN.

  For the WLC to connect to the Dual Core Switch, I need to use only a Management Interface with port 1 being the main and mapping Distribution system the DS 2 Port as the backup for the Management Interface port. Is this correct? or can I have configure dynamic Interfaces as well. Is the interface of access management / management and configuration only? Management interface will communicate with ACS for AAA and AP who wish to associate with the WLC, is this true?

  Note: WLC, AP, Wireless customers & AP are in the same IP subnet.

  Some other question of WLAN is so it helps me during the implementation.

  Can • I use the 802. 1 x authentication applications saved in Windows XP for the Wireless Interface; instead of the Client Application from Cisco. For this purpose; I have to configure the WLC / Wireless Client use EAP algorithm; is that correct?

  • With the help of MRR, interference between of multiple (3-4 AP) AP in the same area is controlled by the WLC by changing the channels used by the AP, that isn't even on of the AP is it good?

  • How many users Client will connect by channels. 802.11 a / g will provide 11 channels, it is right?

  • I'm putting in the WLC to limit client connections by AP to 25, can this be achieved?

  Please, can someone help me calrifying the points above.

  Kind regards

  Keshava Raju

  Unless this has changed recently, you can't. The ports must be then break into individual groups. You can the controller mode layer 3 as Cisco is the support Layer 2 stop. The Director of the PA is necessary in all cases in LWAPP layer 3 transport mode. Do a search on Cisco.com to the configuration guide for the version of the code you are running. This will give you a step by step installation instructions.

• WLC 7.4.121.0 configuration management interface

  Hello.

  I have a problem Management interface IP setting in new 5508 controller. I get the error "error in the management interface IP configuration". I can't put a management controller IP.

  Start IPv6 Services: ok
  From Config Sync Manager: ok
  Start Hotspot Services: ok
  Starting the PMIP Services: ok
  Starting the Services of Portal Server: ok
  Starting the mDNS Services: ok
  Start Management Services:
  Web server: CLI: ok
  Web security: authentication certificate Web not found (error). If you cannot access the management interface via HTTPS please reconfigure virtual Interface.
  License Agent: ok

  (Cisco controller)

  Welcome to the Setup Wizard Cisco tool
  Use the '-' character of backup

  You wish to terminate autoinstall? [Yes]: -.
  Invalid response

  You wish to terminate autoinstall? [Yes]: no

  Name of the system [Cisco_bf:dd:c4] (31 characters max):
  AUTO-INSTALL: process completed - no configuration not loaded

  Enter administrative username (up to 24 characters): admin
  Enter the administrative password (3 to 24 characters): *
  Administrative password: *.

  Interface Configuration for IP [static] [DHCP] address service: no
  The service Interface IP address: 1.1.1.1
  Service Interface subnet mask: 255.255.255.0

  Enable aggregation LAG (Link) [Yes] [NO]: no

  The Interface IP address management: 192.168.10.1
  Management Interface subnet mask: 255.255.255.0
  Router default Management Interface: 192.168.10.10
  Error in the management interface IP configuration

  The Interface IP address management: 10.10.10.1
  Management Interface subnet mask: 255.255.255.0
  Management router default interface: 10.10.10.100
  Error in the management interface IP configuration

  Address IP Management Interface:

  ····························································································

  Did someone in the face of this issue?

  Thank you.

  Hello

  Try these:

  1. with the WLC, please the Frother (in SecureCRT or hperterminal) the value none. Once the changes are made, CLI will start to work as usual.

  2. Another common reason may be related to the configuration of the virtual interface of the controller. To resolve this problem, remove the virtual interface, and then re - generate with this command:

  WLC >config interface address 1.1.1.1 virtual

  Then restart the controller. After that the controller is restarted, re - generate the certificate webauth locally on the controller with this command:

  WLC >config certificate generate webauth
  In the output of this command, you should see this message: Web authentication certificate has been generated.

  Now you should be able to access the secure web mode of the controller to restart.

  3. try to use a diff for the service interface IP address do not use 1.1.1.1.

  Concerning

  Remember messages useful rates

• WLC 5508 management interface

  Hi, I have a design requiring a WLC 5508 be connected to two separate swithces specific wireless. WLC 1 port is connected to the switch A trunk and WLC Port 2 is connected to the switch B. Each switch has its own local VLANS. When I connect the years 1130 towers they need find the interface of management initially then only use management. AP interfaces since there is only a single management interface, if the assignment of management interface on a VLAN that is configured on the switch then APs on spend a fine join but those switch B continue to ask for the management interface and the version debug capwap on WLC he says that this query Join were received on the bad ineterface...

  the only work around that was to do the routing between switch A and switch B for both VLAN residing APs... but for security reasons - customer would like to avoid this

  any help is appreciated...

  Unfortunately, the initial discovery must arrive in the management interface.  Once this has happened the AP expected the second AP manager who is on the subnet of comments, therefore, they are able to stand.  But if the AP is restarted, it would need to discover once again and would fail.

  What is the concern of customers to have all routable network mgmt AP?  guest users can not see anything there.

  IMO, let the AP able to connect to the subnet of mgmt, but then put an ACL L3 upward, to block the subnet of comments to achieve anything in the internal network.

• 4240 IPS management interface MAC address

  Hi all

  I use DHCP in my network. And I need to book a single IP address for the Interface of management of the IPS.

  I tried to get the MAC but could not. It is not yet on the Show of support.

  Can a please tell me how to get the MAC address IP management interface?

  If the interface to see the output does not give you this information, you can connect via the service account and run the command "ifconfig - a". Just make sure you do a 'su' - otherwise this command is not available.

  Please note if useful :)

  Concerning

  Farrukh

• WLC 5508 Management interfaces

  I'll put up a new 5508.  I have used the config of a 4402, have successfully connected to the path of Service to manage the device, but for some reason any cannot connect to the management interface.  In this case, port 1.

  The service port is connected to a catalyst switch and grabbed an IP (subnet 10.2.x.x) no problem.  I can access the 5508 via https using MS.  However, port 1 is connected to the same Catalyst switch, but on one vlan different (10.20.x.x subnet).  Both ends show that interfaces are in place, I can ping the interface from any other host on the network, but when I try to run the device via https I can't connect.  We use the WCS and I can't add the device to the WCS.  About all I can do is ping this interface.

  I probably forgot something very basic, but I'm stumped.

  We have the same Cisco 5508 controller and we discovered that if you use a computer on the same subnet that the Service interface, you won't not be able to connect to the management of a via HTTP or SSH, even though you 'll be able to ping. We changed the IP address of the service interface, and then we were able to connect to the management of a site.

• Questions on the WLAN and AP Manager interface

  Hello

  In fact, I was searching in the internet for more information on the (the AP Manager interface), I've only had the following link on the configuration of WLC.

  http://www.Cisco.com/en/us/docs/wireless/WCS/7.0/Configuration/Guide/7_0admin.html

  -If you have more information about this interface, share with me pls

  My second question is about the WLAN. In fact, I connected the AP lightness to the controller directly via a private network and configured WLAN with SSID. The question im face that customers can see the SSID, but can not be associated. I mean the packets sent is complete but the packets received too low, so I can't access the net.

  How can I solve this problem?

  Should I SWITCH to connect 3 AP light to the controller and the location device? or its just to connect these APs and the controller directly to our private network, because we use the same subnet.

  Thank you

  concerning

  Hello

  The link below can give u some info and you can be knowing this as well

  http://www.Cisco.com/en/us/docs/wireless/controller/5.2/configuration/guide/c52mint.html#wp1117288

  Then regarding the WIFI network... If you are able to see the SSID but not able to associate... What is the quthentication and the encryption is we help? We receive the IP or not?

  Private network means? the WLC will connect to the switch, right?

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• Management interface

  I have 2 ASA 5550's in a configuration of active / standby. The client wants to put some sort of 3rd party outside the ASA sitter. They should watch the two ASA at the same time. Can the management interface given a different address on each box.

  Example:

  ASA 1 192.168.1.1

  ASA 2 192.168.1.2

  We are running out of 72 7.1 (2)

  Thank you

  David

  The watch system is never used by the customers themselves. No matter what device is 'Active' it starts you answer the 'Active' IP address and the "Standby" unit takes the IP address of "Standby". However, you can telnet/snmp for each IP address. And that should meet your goal.

  There are a few difficult flats, for example if the management Machine is accessible to the ASA via a dynamic routing protocol while the relief unit will not have these dynamic routes in its routing table. It will take special workaround solutions. Other than that, you can connect to the rescue unit when you want. However this is not recommended/supported to make changes on the rescue unit. Surveillance is hard OK.

  Concerning

  Farrukh

• The ASA Independand IP management interface

  Hello

  I have a pair of ASA 5510 running like a pair of failover 8.4.

  Currently, we have 3 interfaces prod and are also using the management interface in the form of a group management interface.

  AS I joined the two using failover, the interface of management on the second ASA took the IP address of the first. Is it possible to exclude this HA interface so that we can manage, via IP, each device independently? The main reason for this is that two devices sit in different DC so we have another out-of-band to each site network.

  Thank you

  Anthony

  Hello

  I have not personally at least knows of anyway to do this because the devices share the same configuration and switch interface IP address depending on which device is active in the pair.

  To my knowledge each physical interface that is not configured for subinterfaces should be part of the default recovery. I guess in your case, even if it is not accomplish what you're after, you should probably configure "without monitor-interface", if not, to my knowledge, it might affect the State of failover?

  I don't know if there really is a way to make it work as you want. I think Cisco assumes that the management interface is like any other data interface in failover and it requires connectivity between sites where pairs of ASA.

  I guess it would be better if the Console port has been used for this purpose and you had a separate device you can remote access to the Console of the machine you want.

  If you want to send commands to the other ASA the failover and link then it is possible

  For example, you can connect to an ASA and execute commands from the failover link

  exec failover partner

  But again, I don't know if this will be of any help in your situation.

  -Jouni

• Nexus 7 K of the group management interface

  Dear,

  with regard to the release of the group management interface, if I configured a vlan intervace to be as an interface of management for a (the default vdc) vdc

  When I connected to this vdc via telnet, can I switch to any other vdc?  (Suppose I have the role of the Admin that allows me to enter and config all the VCC)

  If possible, so that I don't have to do a management dedicated to each VDC ip

  I do that only if I want to give an account of the vdc admin to allow some users access to the VLAN specific only, is it true?

  Hello

  Yes, it is possible.  When you log on as an administrator and you want to join another vdc, you simply use this command:

  SwitchTo vdc

  This will lead to the vdc.  If you want to return to the admin vdc, just type "switchback."

  HTH