active monitoring of remote access vpn connections
Hi all
I use asa 5520, and asa 5540 for remote access vpn connections. Is it possible to active my vpn connections monitoring so that there would be alerts for vpn tunnels which fail to implement for other reasons other than the authentication of users? Pls advise. Thks in advance.
Kiwi Syslog will work fine - as long as you have a licensed version, a 'free' version does not support e-mail extras.
See the url below and search for "VPN", you will see what VPN syslog codes you can choose from.
http://www.Cisco.com/en/us/docs/security/ASA/asa83/system/message/logmsgs.html
HTH >
Tags: Cisco Security
Similar Questions
-
Urgent! Users of remote access VPN connects but cannot access remote LAN (ping, folder,...)
Hello
I am setting up a VPN on a Cisco ASA 5510 version 8.4 remote access (4) 1.
When I try to connect via the Cisco VPN client software, I am able to connect however I am unable to access network resources.
However, I can ping the servers in the other site that is connected through the VPN site-to site to the main site!
VPN client--> main site (ping times on)--> Site connected with the main site with VPN S2S (successful ping)
Please help me I need to find a solution as soon as POSSIBLE!
Thank you in advance.
Hello
Please remove the NAT exemption and the re - issue the command but with #1, so it will place the NAT as first line:
No nat (SERVERS, external) static source SERVERS_LAN SERVERS_LAN NETWORK_OBJ_10.10.40.8_29 NETWORK_OBJ_10.10.40.8_29 non-proxy-arp-search of route static destination
NAT (SERVERS, external) 1 static source SERVERS_LAN SERVERS_LAN NETWORK_OBJ_10.10.40.8_29 NETWORK_OBJ_10.10.40.8_29 non-proxy-arp-search of route static destination
After re-configured this way, make sure that this command is also available:
Sysopt connection permit VPN
This sysopt will allow traffic regardles any ACL a fall, just in case. Please continue to run a package tracer and post it here,
Packet-trace entry Server icmp XXXXXX 8 0 detailed YYYYY
XXXX--> server IP
AAAA--> VPN IP of the user
Don't forget to do the two steps and a just in case, capture Please note and mark it as correct the useful message!
Thank you
David Castro,
-
AnyConnect VPN client can be used for IPSec remote access VPN connection?
I think I heard it somewhere that AnyConnect VPN can be used for connections SSLvpn IPSec VPN. Is this possible? Thank you!
No, the Anyconnect software cannot be used to establish the framework for a VPN IPSEC IKE.
-
We have 10 sites with ASA 5505 connected to the ASA 5510 of main office
through IPSec VPN tunnels. Home users connect to the main office network
using the remote access vpn connection. They can also connect to the ASA 5505
remote sites by vpn for remote access to the ASA 5510?
Thanks, please help!
Here's the PDF.
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
remote access VPN not connected - no access inside
Hi, I have successfully configured remote access VPN router, it is connected, but no access to the inside, none of my ip addresses. I do not know SPLIT_ACL is ok and I've denied NATting them. For me, everything is ok. I did a lot in ASA, without anyproblem. Thanks for the comments.
enable secret 5 $1$ y0AJ$ rhrjbrpe5NDiAyHGlfeNi.
!
AAA new-model
!
!
AAA authentication login bcc_users local
AAA authorization bcc_group LAN
!
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 2
!
ISAKMP crypto client configuration group ra_vpn_bcc
key *.
DNS 8.8.8.8
bcc.local field
pool vpn_pool
ACL SPLIT_ACL
Max-users 7
netmask 255.255.255.0
!
!
Crypto ipsec transform-set RIGHT aes - esp esp-sha-hmac
tunnel mode
!
!
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
market arriere-route
!
!
card crypto client CRYPTO_VPN of authentication list bcc_users
card crypto isakmp authorization list bcc_group CRYPTO_VPN
crypto card for the CRYPTO_VPN client configuration address respond
map CRYPTO_VPN 10-isakmp ipsec crypto dynamic dynmap
!
!
interface GigabitEthernet0/0/4
IP address %.
NAT outside IP
auto negotiation
BFD interval 50 50 5 min_rx multiplier
card crypto CRYPTO_VPN
!
!
IP local pool vpn_pool 172.31.255.0 172.31.255.250
NAT extended IP access list
deny ip 10.0.0.0 0.255.255.255 172.31.255.0 0.0.0.255
deny ip 172.16.0.0 0.0.255.255 172.31.255.0 0.0.0.255
deny ip 192.168.0.0 0.0.255.255 172.31.255.0 0.0.0.255
IP address 172.16.0.0 allow 0.15.255.255 all
IP 192.168.0.0 allow 0.0.255.255 everything
IP 10.0.0.0 allow 0.255.255.255 everything
SPLIT_ACL extended IP access list
IP 10.0.0.0 allow 0.255.255.255 172.31.255.0 0.0.0.255
IP address 172.16.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255
IP 192.168.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255
Take a look at the delivery.
You do not have a route to the VPN pool on a nearby device.
-
Hi all
I need help with remote access vpn configuration. I want to some remote users who have access to the internet on their system to connect and access an application server in my seat social cisco vpn client user. I use Cisco 881. I am unable to use the SDM configuration because it seems that SDM is not supported by the router so I'm using command line. I'd appreciate any help I can get. Thank you.
This is the configuration I have:
VPNROUT #sho run
Building configuration...Current configuration: 6832 bytes
!
! Last configuration change at 10:50:45 UTC Saturday, May 30, 2015, by thomas
version 15.2
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname VPNROUT
!
boot-start-marker
boot-end-marker
!
!
logging buffered 51200 warnings
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login userauthen1 local
AAA authorization groupauthor1 LAN
!
!
!
!
!
AAA - the id of the joint session
iomem 10 memory size
!
Crypto pki trustpoint TP-self-signed-1632305899
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 1632305899
revocation checking no
rsakeypair TP-self-signed-1632305899
!
!
TP-self-signed-1632305899 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
69666963 31363332 33303538 6174652D 3939301E 170 3134 30313233 31323132
33325A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36333233 65642D
30353839 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
8100BC0C 341CD79B A38572CE 1F0F9A91 F96B133C A889B564 E8352034 1CF5EE4B
B505616B 6014041B EC498C0A F6C5CD2B F5BF62DA BD6E1C44 0C7B9089 1FD0C6E5
299CEB40 28CD3F3B ADE3468A B07AAA9F AC42F0A7 4087172A 33C4013D 9A50884D
5778727E 53A4940E 6E622460 560C F597DD53 3B 261584 E45E8776 A848B73D 5252
92 50203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 D
551 2304 18301680 14E85AD0 DEF133D8 E09516FD 0AA5FDAD E10EAB1A FA301D06
03551D0E E85AD0DE 04160414 F133D8E0 9516FD0A A5FDADE1 0EAB1AFA 300 D 0609
2A 864886 818100A 5 05050003 5B23ED5B 9A380E1F 467ABB03 BAB1070B F70D0101
7A 218377 73089DC1 D32DA585 C5FD7ECE 0D000F96 7F3AB6CC 71509E8F 3F1C55AE
E37536A3 1008FBF9 A29329D5 6F76DDC0 AA1C70AE 958AAE5D 32388BE4 2C1C6839
0369 D 533 027B612C 8D199C35 C008FE00 F7E1DF62 9C73E603 85C3240A 63611D 93
854A61E2 794F8EF5 DA535DCC B209DA
quit smoking
!
!
!
no record of conflict ip dhcp
DHCP excluded-address IP 10.10.10.1
DHCP excluded-address IP 172.20.0.1 172.20.0.50
!
DHCP IP CCP-pool
import all
Network 10.10.10.0 255.255.255.248
default router 10.10.10.1
Rental 2 0
!
IP dhcp pool 1
network 172.20.0.0 255.255.240.0
domain meogl.net
router by default - 172.20.0.1
172.20.0.4 DNS server 41.79.4.11 4.2.2.2 8.8.8.8
8 rental
!
!
!
no ip domain search
IP domain name meogl.net
name of the IP-server 172.20.0.4
name of the IP-server 41.79.4.11
IP-server names 4.2.2.2
8.8.8.8 IP name-server
IP cef
No ipv6 cef
!
!
license udi pid CISCO881-K9 sn FCZ1804C3SL
!
!
username secret privilege 15 thomas 4 JXSizd1r/hMqPpGz94vKBb5somtpZLy03k50rJvHO6c
username privilege 15 secret 4 mowe hlfv/rdDRCAeTUzRXbOIfdaKhJCl1onoGdaQeaQsAnw
!
!
!
!
!
!
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
ISAKMP crypto client configuration group moweclients
XXXXXXX key
DNS 172.20.0.4
meogl.net field
pool mowepool
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac moweset
tunnel mode
!
!
!
Dynmap crypto dynamic-map 1
Set transform-set moweset
market arriere-route
!
!
card crypto client mowemap of authentication list userauthen1
card crypto isakmp authorization list groupauthor1 mowemap
client configuration address card crypto mowemap answer
mowemap 1 card crypto ipsec-isakmp dynamic dynmap
!
!
!
!
!
interface Loopback0
IP 172.30.30.1 255.255.255.0
IP nat inside
IP virtual-reassembly in
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
switchport access vlan 100
no ip address
!
interface FastEthernet3
no ip address
!
interface FastEthernet4
IP 41.7.8.13 255.255.255.252
NAT outside IP
IP virtual-reassembly in
intellectual property policy map route VPN-CLIENT
Shutdown
automatic duplex
automatic speed
mowemap card crypto
!
interface Vlan1
Description $ETH_LAN$
IP 10.10.10.1 255.255.255.248
IP tcp adjust-mss 1452
!
interface Vlan100
IP 172.20.0.1 255.255.240.0
IP nat inside
IP virtual-reassembly in
!
local pool IP 192.168.1.1 mowepool 192.168.1.100
IP forward-Protocol ND
IP http server
23 class IP http access
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP nat inside source overload map route interface FastEthernet4 LAT
IP route 0.0.0.0 0.0.0.0 41.7.8.12
!
access-list 23 allow 10.10.10.0 0.0.0.7
access-list 23 allow 172.20.0.0 0.0.15.255
access-list 100 permit ip 172.20.0.0 0.0.15.255 everything
access-list 144 allow ip 192.168.1.0 0.0.0.255 any
not run cdp
!
LAT route map permit 1
corresponds to the IP 100
IP 41.7.8.12 jump according to the value
!
route VPN-CLIENT map permit 1
corresponds to the IP 144
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
access-class 23 in
privilege level 15
transport input telnet ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
!
!
endPlease the configuration above, give me the desired output.
Thank you.
Hello Thomas,.
I'm glad to hear that you have found useful in the example configuration.
I checked your configuration and everything seems ok with him, especially the statements of nat.
ip local pool mowepool 192.168.1.1 192.168.1.100 access-list 100 deny ip 172.20.0.0 0.0.15.255 192.168.1.0 0.0.0.255 access-list 100 permit ip 172.20.0.0 0.0.15.255 any route-map LAT permit 1 match ip address 100 ip nat inside source route-map LAT interface FastEthernet4 overload interface Vlan100 ip address 172.20.0.1 255.255.240.0 ip nat inside ip virtual-reassembly in
Try to generate ICMP traffic behind your 100 VLANS to the client VPN in order to answer the following questions:
-The router receives this traffic between VLAN100 unit?
-The router is encrypt this traffic, after receiving the ICMP packet?
#show crypto ipsec router its can help you with this question. Look for the program/decaps counters.
-The same, but the other way around (from VPN client to device behind VLAN100) try to locate the problem.
The following document explains more this crypto commands and debugs if necessary.
-
Remote access VPN user permission
Hi support them.
It is a way for a remote access VPN to allow some users access to "Host A, B, C" and other users to access hosts D, E, F? Basically, we want to have some users have access at home to a few servers and other users have access only to some other servers. Is this possible without a GANYMEDE or some other device? Thank you guys!
Hi John,.
Yes, you can configure split tunneling to allow a specific group of users access to specific hosts.
How this is achieved, it is that you create a connection profile different for different users, associate a policy group and the title of each group policy, you have a split tunnelling access-list defined with entries of different hosts.You must create 2 profiles of connection here and match them with 2-group policy allowing access to 2 differernt resources (they can be multiple as well)
Here is a reference document: -.
Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
PIX 515E and remote access VPN
I use a PIX 515E with: ASDM Version: 5,0000 51 PIX Version: 8.0 (4) and configure it with remote access VPN.
I would like to get an email every time that a user login (and or disconnection) to the VPN. Remote clients use the Cisco VPN Client.
Any help is appreciated,
Hello
Here is a link to the email configuration when you log in to the ASA/PIX: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc7
Then you can create a list of message to send the logs only for the connection/disconnection of the VPN user: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc18
There is a wire that is linked here: https://supportforums.cisco.com/discussion/10798976/asa-email-logging-issue
-
Remote access VPN fails after upgrading to 8.04
Hello:
Sorry if this has been posted, but I couldn't find it anywhere.
After the upgrade of my 2 of my 5510 s to 8.04, my remote access VPN does not work. I can connect via Radius without problem. Once connected, I can't do anything on the network. When I try to telnet to any device, I get a white screen with no response. As it is to find the device but it does not. E-mail, intranet, nothing works. Seems to be time. I tried to upgrade to the latest version of Windows Client, still no go.
Everyone knows this at all? Any help appreciated.
TIA,
Brad
I saw the same problem after upgrading to 8.0.4. And it is caused by the "IP Compression" option enabled in group policy. After deactivation, it works. Cisco has just completed this bug recently:
Zhenning
-
Remote access VPN pix version 8.0 (3)
Hi all
First of all, I would like to thank to all members of the forum who got help in several messages on the configuration of the pix 515.
I am now configuring remote VPN access with radius authentication to my network, but I can't connect.
I use the cisco vpn client 5.0.03.0560, I have also tested my pix radius (inside) server authentication and works very well.
I already tried to retype the key of the cli, but I still can't remote access vpn to work.
I also tried to create another remote vpn with another name and local authentication, but I have the same problem.
I use 8.0 (3) version pix.
Can someone help me
I attach the log file of the cisco vpn client to help solve the problem, as well a configuration of the pix folder.
Thank you very much in advance and I seek prior information.
http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/vpnadd.html#wp999516
[Pls RATE if HELP]
-
Service of ASA module does on 6509-E support remote access VPN?
I'm having a problem of configuration of remote access VPN (SSL, Anyconnect ect.) on the Module of ASA Service on 6509-E. It is even supported or I'm wasting my time trying to do something that won't work in a first place :) to work? Site-to-Site works without any problem.
Technical info:
6509-E current SUP 2 t SY 15.1 (2)
Module of ASA - WS-SVC-ASA-SM1 running of the image - asa912-smp-k8 & asdm-712
Licenses on ASA:
Encryption--Activated
3DES-AES-Encryption - enabled
Thank you for the support.
You run multiple context mode?
If you are, access remote VPN only is not supported in this case:
"Note several context mode only applies to the IKEv2 and IKEv1 site to another and applies not to the AnyConnect, clientless SSL VPN, the legacy Cisco VPN, native VPN client client of Apple, the VPN client from Microsoft or cTCP for IKEv1 IPsec."
-
Hello!
I have 9.1 (3) version of Cisco ASA with remote access VPN set UP on the outside interface. When the user connects to the Internet on the outside interface, it works well. My goal is to allow the connection of all other interfaces (inside the dmz and etc.) to the outside interface. Cisco ASA allows to do? Order to packet - trace output is less to:
MSK-hq-fw1 # packet - trace entry inside tcp 10.10.10.1 14214 1.1.1.2 443
Phase: 1
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
developed 1.1.1.2 255.255.255.255 identity
Phase: 2
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
developed 1.1.1.2 255.255.255.255 identity
Result:
input interface: inside
entry status: to the top
entry-line-status: to the top
the output interface: NP identity Ifc
the status of the output: to the top
output-line-status: to the top
Action: drop
Drop-reason: (headwall) No. road to host
Hello
Well, you can of course turn VPN on other interfaces, but to be honest, I never even tried to set up the VPN it otherwise than of multiple multiple external interfaces in the case of the ISP and in this case only for testing purposes.
Some things related to the ASA are well known but not well documented.
The official document that I can remember: this is the following (which only refers to this limitation regarding the ICMP)
Note
For security purposes the security appliance does not support far-end interface ping, that is pinging the IP address of the outside interface from the inside network.
Source (old configuration guide):
-Jouni
-
How to use ACS 5.2 to create a static ip address user for remote access VPN
Hi all
I have the problem. Please help me.
Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.
I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:
1Ajouter step to attribute a static IP address to the user attribute dictionary internal:
Step 2select System Administration > Configuration > dictionaries > identity > internal users.
Step 3click create.
Static IP attribute by step 4Ajouter.
5selectionnez users and identity of the stage stores > internal identity stores > users.
6Click step create.
Step 7Edit static IP attribute of the user.
I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.
so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.
Wait for you answer, no question right or not, please answer, thank you.
There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached
-
Problem with remote access VPN
Hello
I installed a remote access VPN on my firewall ASA5505 via the ASDM Assistant.
I can successfully connect with the Cisco VPN client. My firewall also shows me the VPN session and shows the Rx packets. However, Tx packets remain 0, so no traffic is getting out. My ASA5505 is configured as a router on a stick with 25 different VLAN. I want to restrict traffic to one VLAN specific using a card encryption.
When I run a command to ping t on my connected Windows box, the firewall log shows me the following message:
"Unable to find political IKE initiator: outside Intf, Src: 10.7.11.18, Dst: ' 172.16.1.1
"This message indicates that the fast path IPSec processing a packet that triggered of IKE, but IKE policy research has failed. This error could be associated calendar. The ACL triggering IKE could have been deleted before IKE has processed the request for initiation. "This problem will likely correct itself."
Unfortunately, the problem is correct.
The "sh cry isa his" and "sh cry ips its ' commands show the following output:
2 IKE peers: 62.140.137.99
Type: user role: answering machine
Generate a new key: no State: AM_ACTIVE
Interface: outside
Tag crypto map: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 85.17.xxx.xxx (outside interface IP)
local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)
Remote ident (addr, mask, prot, port): (172.16.1.1/255.255.255.255/0/0)
current_peer: 62.140.137.99, username: eclipsevpn
dynamic allocated peer ip: 172.16.1.1
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 4351, #pkts decrypt: 4351, #pkts check: 4351
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0
local crypto endpt. : 85.17.xxx.xxx/4500, remote Start crypto. : 62.140.137.99/3698
Path mtu 1500, fresh ipsec generals 82, media, mtu 1500
current outbound SPI: B3D60F71
current inbound SPI: B89BA14A
SAS of the esp on arrival:
SPI: 0xB89BA14A (3097207114)
transform: aes - esp esp-sha-hmac no compression
running parameters = {RA, Tunnel, NAT-T program,}
slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP
calendar of his: service life remaining key (s): 25126
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0xFFE1FFF8 0xFFFFFFFF
outgoing esp sas:
SPI: 0xB3D60F71 (3017150321)
transform: aes - esp esp-sha-hmac no compression
running parameters = {RA, Tunnel, NAT-T program,}
slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP
calendar of his: service life remaining key (s): 25126
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
I really have no idea what's going on. I installed a remote access VPN countless times, but this time it shows me the error as described above.
Hi Martijn,
just a few quick thoughts:
-is your ok NAT exemption, i.e. ensure that the return traffic is not NAT' ed.
-Make sure that there is no overlap crypto ACL
-When connected, make a package tracer to see what is happening with the return packages.
for example
packet-tracer in the interface within the icmp 10.7.11.18 0 0 172.16.1.1 detail
(where is the name of the interface on which 10.7.11.18 resides)
This will show you all the steps the rail package in-house (routing, nat, encryption etc.) so it should give you an idea of what is happening, for example when it comes to the bad interface, nat evil rule, wrong entry card crypto etc.
HTH
Herbert
Maybe you are looking for
-
I need information about keychain.
I sought help in my iMac and sought here in Apple Support communities for more information on keychain. Nothing shows that relates to my request. Which currently has told me is that Keychain linked all my Apple devices. Recently, I changed my passwor
-
Folio 1020 G1 keyboard works not for 30 seconds after the computer wakes from sleep
I have several books of Folio 1020 G1 where the integrated keyboard does not work for about 30-60 seconds after the resumption of the operation of the standby mode. Everyone met this problem or a solution? The touch pad, touch screen and a usb keyboa
-
I use a time machine / capsule (latest generation) to my wifi. Just purchased a Lorex security for my home that needs to be connected to the internet (via ethernet). Can I plug the ethernet cable into my time machine without affecting my WIFI? Or I n
-
% < Double > erratic battery charging
Hello Recently, I noticed a few questions while ac load my motox 2ndgen. Two days ago the battery stopped load from 86 percent. Turn off cable inserted ordnance from 86 to 100% with the ca. Today a similar thing happened where it stopped loading at 9
-
c:\windows\system32\driverstore\filerepository\hpoa1ss.inf_520d224f\hpotscl1.dll
When you run a deep scan on Windows Defender and BitDefender programs and all of the computer freezes when the analysis reaches the following file: c:\windows\system32\driverstore\filerepository\hpoa1ss.inf_520d224f\hpotscl1.dll What is this file and