Add the second disc

Similar Questions

• Available to add the second internal hard drive to 17-e117dx

  Hello

  Can you let me know, if there is provision to add the second internal hard drive for HP Pavilion e117dx 17.

  If so, one) is there requirments or the specifications of the hard disk (any make or model); (b) what equipment will be needed and where I can get to and c) Finally will be doing so make sure the warranty of my laptop HP Sub

  HP Pavilion

  Product: F9J38UA #ABA

  Model: 17-e117dx

  Thank you

  Not in the way you probably do. Here is the Service Manual:

  Manual

  See Page 50. Unlike the Envy 17 and Pavilion dv7, Pavilion 17 has that a single hard drive Bay. The only way to add a second hard drive is to remove the DVD (optical drive) and insert a DVD to the hard drive bay adapter. The manual shows how to remove the DVD player and you can buy the adapter at amazon.com or jacobsparts.com. Note that this is a 9.5 mm thick disc, not a 12.7 mm. Both types are available. I do not recommend the adapter DVD player solution because you lose the use of the optical drive, and also because the interface of optical drive is usually not as fast as the main hard drive interface. Always fast enough for simple storage and you can run a video of her, but you do not want to edit the video of this disc, for example.

  https://www.jacobsparts.com/items/HDDBAY-02/

  If you decide to go the route of adapter DVD I would buy a large capacity 5400 RPM SATA 2.5 inches wide and drive hard thickness 9.5 mm. No sense in buying a reader more expensive high-performance.

  http://www.Newegg.com/product/product.aspx?item=N82E16822178006

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• How can I change the drive letter of the second disc of C: to another letter?

  original title: I add an opportunity second hard drive labeled C:. How can I change the drive letter of the second disc of C: to another letter?

  I'm runnibg Vista service pack 1 on a Compaq Presario with a labeled hard drive C:.

  No you haven't, how it was labeled in the old pc is irrelevant, just install you it as slave on your PC drive, depends on the question of if you need to change the jumper on the drive. Some PC manufacturers require the rider to be set as "cable select" others as "slave" (unless of course, it's a sata drive that requires no jumpers)

  Once it is set, when you start your PC, it will be assingned a drive letter

• HP compaq 8200 elite sff: Add the second hard drive to 8200 elite sff

  I installed a second hard drive, but the system does not reqagnize it.  I connected the blue sata port.  Any help?

  Well shit, now I have to retype my response... I typed in Notepad, but it seems that I can't copy and paste into this box.

  I agree with DFBonnett, the second disc will only work on the BLACK, not BLUE light connector.

  The way I Win-10 to see the second drive was to go to the management of the computer, and then under storage, click Disk Management: the drive is presented as a disc 1 but not show the program explores until I received a letter from the disk drive... MAGIC, the player will now display as the letter assigned to the I gave him 'E' with a backup label.

  I tried what erico posted but has not worked, but I thank all of you who have tried to help.

  I give credit to Umbutu, he saw the drive without having to do anything myself.

  Hey Microsoft, look at what Linux can do... lol

• Player Windows Media will be not to extract the second disc as a whole - it's disk 1

  I have a set of two discs.  Disc one ripped fine.  But when I put in disc 2, it rejects, thinking it is disk 1.

  When I put and try to play, all the information display is that of disc 1, but it is playing music from disc 2.
  Hope that makes sense.  How to stop thinking that Disk 2 is disk 1?

  Well, I think I found a solution.

  I deleted the first disc of my library and my computer, so that no debris from the album remained.
  I inserted and ripped out the second disc.  I went to the library view, you click on 'Album' in the left pane and scroll to the album just torn.  I clicked on it and selected "Find Album Info".  When he doesn't get the info, ask if it is correct.  Rather than make a new search, as it says, click blue "Edit" next to album art.  You will then be able to modify information, rename and renumber the pieces and make a set of disks instead of a single disc.
  I clicked done, then finished, and it is updated correctly in my library.  I tore the first disc, went through the same procedure to make a disc placed instead of one disc and ensured that he he showed as a disc 1.
  Everything seems to be updated correctly now.

• Access denied to the second disc

  My hard drive went wrong, so I bought two new albums: SSD for the OS and a few applications and a regular hard drive for data. I pulled the old drive, threw the new ones, reinstalled Windows on the SSD, and everything was good! I have created a few directories on the HHD, downloaded files in there and then I rebooted to finish a few things from Windows Update.

  When I logged in, I could not open the phonebook on the HHD containing my downloaded files. "D:\ is not accessible. Access is denied. "This has constantly produced with the second disc.

  Some info:

  • Windows 7 Pro 64-bit
  • C: drive is a NEW SSD drive with an operating system installed on it
  • D: drive is a NEW HHD for data
  • I connect with the user during the installation, I created. This user is in Admin group.
  • As far as I can tell, I have no problems with permissions on the SSD
  • A lot of people have this problem with the old disks after upgrade or reinstall - this is not the case here! These discs are new.

  I tried the things:

  • Granting of permissions/access my user group is part of the
  • Granting permissions/access directly to my user
  • Granting a group ownership of the directory my user is part of the
  • Granting ownership of the directory to my user
  • Do the foregoing to various combinations of input drive root, parent directories, etc.
  • Reformat the drive several times - this solves the problem for a while, but he returned after a few reboots

  Granting permissions or take ownership usually results in an "access denied" message I can perform these functions if I log in safe mode.

  Does anyone have any ideas or suggestions? I am completely frustrated and confused at this point. I have full access rights and have even files, but still receive "access denied" errors

  I reinstalled the latest Intel storage drivers and the problem seems to be resolved.

• How can I get the second disc of student CS4 edition to install?

  I installed the first disc of the student CS4 edition and tells me to put in the second disc to continue installation. However, there is no way to install the second disc and I can't click ok, cancel, or exit. any advice would be great.

  Hello

  Try to Download CS4 products

  Hope that helps!

  Kind regards

  Sheena

• Advanced conditional action does not work when I add the second condition

  I use CP 8. I can't understand why I'm running on this problem. I have a series of If-Then conditional actions, but I am running into problems. I narrowed down it to this problem.

  It is a simple check box that must show either the box or not.

  

  As long as I have only one condition, it works fine. As soon as I add the second condition, it stops working.

  

  Any suggestions? I appreciate the help!

  Rick and I tried to explain that a conditional action is always executed completely. This is the reason that the second decision has been reset what had been done in the first in your first question. I have a lot of articles on my blog where I point out that bad sequence in the decision (or) is causing most of the problems with conditional advanced (shared) actions.

• Add the second NETWORK card to vSwitch

  I'm working on trying to add to install a second NIC physical to the vswitch which is installed by default when ESXi. I use the code below, but when I run it, it disconnects in fact the main physical network card and of course, I then lose connection. I tried different varients of this and even finished by adding a port of vmk, which I didn't do. I just want to add the second network card as a standby card network.

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1
  

  The cmdlet Set-VirtualSwitch accepts a string array as the value of the parameter - Nic. So you should be able to:

  #Add second NIC to the virtual switch
  $nic = Get-VirtualSwitch -VMHost $currentHost -Name "vSwitch0"
  Set-VirtualSwitch -VirtualSwitch $nic -Nic vmnic1,vmnic2
  

  Best regards, Robert

• Add the second hard drive to HPE-400Z

  I am trying to add a secondary hard drive to expand the storage space that I only have 10% of free space on the current.

  "Will buy one online" Seagate Desktop drive HARD 2 to 7200 tr / MIN SATA 6 Gb/s 64 MB Cache 3.5 "-drive retail Kit internal (STBD2000101)" enters the cage OK? Existing drive is Seagate 1 TB guess so, but do not get it and discover it doesn't work.

  This disc has new SATA data and power cables.

  It is clear that there is a free connection of motherboard "SATA2" for data, I can see it. Sounds easy.

  What I can't understand is where and how the POWER cable is connected to... or what might be able to be used which already exists for power connectors in the office. There is a certain and they all have beautiful marking... "P3,"P8",...".

  I found instructions on installing hard drive on HP site... everything is clear for me except for this problem of power cable.

  Did he help me with that?

  GWRootjr, welcome to the forum.

  This is an adapter 'Y' which should solve your problem:

  http://www.Walmart.com/msharbor/IP/24359037?wmlspartner=wlpa&adid=22222222227017782207&wl0=&WL1=g&WL2=t&WL3=40881390152&WL4=&wl5=PLA&wl6=78811224272&Veh=SEM

  You can connect a SATA power cable to do two on one.  This will allow you to connect the second HDD.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Is it possible to add the second cooler to my QOSMIO

  I WOULD LIKE TO ASK IF IT IS POSSIBLE TO ADD THIS SECOND COOLER TO MY LAPTOP * (TOSHIBA QOSMIO - X 300 130) BECAUSE MY LAPTOP SHUTSDOWN WHEN I PLAY GAMES...
  * PIC ALL WHAT I want TO SAY... * http://www.irisvista.com/tech/laptops/Toshiba-Qosmio-X305/big/removing-laptop-motherboard-33.jpg

  AS I HAVE SEE YES BUT WHERE CAN I FIND ONE SUCH COOLER IN YM (BULGARIA)
  EVRYTHING STILL IN WARRANTY

  Post edited by: aloushi

  Hello

  No, it s not possible to add a second cooling fan to the motherboard notebook from the motherboard layout allows and the laptop does not have such extra part.

  But you can test some buffers cooling like this:
  [Photos of cooling pads: http://www.google.de/images?hl=de&q=cooling%20pads&wrapid=tlif130302876 790621 & um = 1 & ie = UTF-8 & source = og & his = N & tab = wi]

• Is it possible to add the second graphics card for this model Y510p?

  I've been doing mixed responses from customer service chat lenovo so I'm posting my question here. Recently, I bought this laptop. It comes with a single graphics card. I heard this model has ultrabay and you add another graphics card. My question is - is it true that you can add a second graphics card in this system by using ultrabay? Please let me know. I'm confused if SLI and ultrabay means the same thing. If this is the case, then this system is not sli. I appreciate your help.

  http://shop.Lenovo.com/us/en/laptops/LENOVO/y-series/y510p/?SB=:000001 C 9: 00011E0A:

  Also, don't forget to find the extra $20 or sometimes $50 discount code for the Lenovo y510p and apply it to the Fund. The time I bought my laptop I used the code USPY5168320, you will find a similar code if this does not work.

• Add the second drive to ATC - 780

  I just purchased an ATC-780-UR61 with a 2.5 ssd "standard that I would add as a second disk as the startup disk and use the disk of 1 TB for storage. Now, I understand that there are only 2 SATA connectors on the motherboard - the one used by the 1 TB drive and 1 by the dvd player.

  Is it possible to add a second drive on this PC? I read some other models have a m2 connector to add a ssd drive to, but I don't see any documentation that the ATC-780.

  I can confirm:

  NGFFM1 m2 SSD connector

  It is on the right side of the motherboard near the SATA 2 ports.

• Add the second server to

  I know this may sound like a matter of "DUH"... How can I add a second server to my closed vWorkspace?

  Currently I have a RDSH server with vWorkspace 8.0 on it (running Win Serv 2008 R2)

  I have a need to get a Server Terminal Server 2003 32 bit in the mix and want to publish an application from THIS server.

  I got it when I connect to AppPortal it shows the application of the 2K 3 server. However, I have some Terminal servers error message; However, AppPortal will launch applications on the original Server vWorkspace

  Hi Mike,.

  If you know the password you used then the remaining details can be found by running the tool ODBC Admin on the Windows Server 2008 is configured correctly. You can use this to look at the correct settings without making any changes. There is no default value as such since the database server and database name are specific to your environment.

  Concerning

  David

• Add the second hard drive to a desktop Pc HP Pavilion P6-2100

  I want to add a second hard drive to a HP Pavilion A1700n Pc desktop to a new HP Pavilion P6-2100 Desktop Pc, so I can transfer files.

  milehisb,

  Welcome on the user forums.  Section manuals PDF from HP did not offer a guide to upgrade and Service.

  There are several options, depending on your needs and your expertise with the internal components of a computer.

  If you goal is to simply get the data off the drive, then put it back in the A1700n, I would use #1.

  (1) use this external adapter for occasional use:http://www.newegg.com/Product/Product.aspx?Item=N82E16812232002

  (2) first search to find if you have a spare Sata power plug. Or you will need an adapter (molex 4pin to Sata).

  http://www.playtool.com/pages/psuconnectors/connectors.html

  http://en.Wikipedia.org/wiki/Serial_ATA

  As the player in question is VIsta, it does not start correctly and could delay the start of WIN7.