Adding a new Powerconnect 6248 switch to battery of existing production

Similar Questions

• My PowerConnect 6248 switch loses its settings when disconnected from the power

  Hello

  I'll put up a PowerConnect 6248 switch on my local network through Web interface (I can't use serial to do).

  I put the IP, login, password, a LAG, SNTP server address, etc.

  It works fine until I unplugged the power cord to the switch to simulate a power outage. When I plugged in the power cord, the switch will reboot by displaying its default settings and I release all of mine.

  Y at - it a specific command, I missed to save all my settings in the switch?

  Thank you for your help.

  Pascal.

  The switch has two separate configuration locations, a running configuration and startup configuration. This allows you to change configuration and test running before engaging them in the startup configuration. Once you have the running configuration, how you want it, you need to run the # copy running-config startup-config command, or just copy # run start.

  See you soon

• Blocking MAC address on PowerConnect 6248 switch

  Hello

  I have a PowerConnect 6248 switch where we want to block a specific MAC address from the rest of the network.

  I created a list of MAC access with the following commands:

  Console (config) #mac access-list extended BLOCK
  Console (config-mac-access-list) #deny 001D.09D4.B08E ffff.ffff.ffff all

  Console (config-mac-access-list) #permit a whole

  I then apply it to all interfaces:

  console (config) #mac group-access BLOCK

  What ends by goes, is that all hosts connected to the switch are blocked when my rule should only be blocking the host with mac address 001D.09D4.B08E.

  What I am doing wrong?

  Thank you!

  Have you tried changing your statement to:

  Console (config-mac-access-list) #deny 001D.09D4.B08E 0000.0000.0000 everything

• PowerConnect 6248 switch

  I have a stack of 7 6248 switches. I added an 8th battery ok but I can get it configured like the rest.

  It just says: its on Default VLAN 1

  I have 3 VLAN 1.22 and 201. All ports show deafault VLAB but only switches 1-7 in the VLAN 22 and 201.

  How can I copy the config info to go to 8?

  1 default ch3-48,

  3/3/xg3-xg4.

  4/4/xg3-xg4.

  5/5/xg3-xg4.

  6/6/xg3-xg4.

  7/7/xg3-xg4.

  8/8/g2-g30.

  8/8/g32-g48.

  8/8/xg3-xg4

  22 c 1-2,

  1/1-g3/g48.

  1/1/xg3-xg4.

  2/2-g1/g48.

  3/g1-3/g48.

  4/4-g1/g48.

  5/5/g1-g48.

  6/6/g1-g48.

  7/g1-7/g48

  201 c 1-2,

  1/1/xg3-xg4.

  2/2-g1/g48.

  3/g48

  5/g1-5/g48

  1/1-g1/g2.

  1/1/xg3-xg4.

  3/g48, 5/g48

  If all ports are going to have the same configuration, you can configure them at the same time.

  Console (config) # interface range ethernet 8/8-g1/g48

  See you soon

• Console port (serial) on Powerconnect 6248 switch

  Hi all

  I have two powerconnect 6248 s. The first I've had for several months. The second, I just ordered recently.

  I can't go to the console in to the second switch. I use the same settings (minicom) and cable that I use regularly to connect to the first switch.

  Any thoughts on how to solve this problem? I don't see any startup dialog after resetting the switch 2.

  Thank you

  Looks like you have experienced just about everything that you can. You checked restarted cable, the emulator settings, confirmed working on the other switch, switch, and the default value and it still does not work. It sounds more like it could be a hardware problem with this port. Is the unit still under warranty?

• Adding two new Windows 7 work stations to the existing network of WinServer 2008

  I bought two new Windows 7 Professional - 64-bit (Dell Precision 3610) workstations. How to set up our server and domain? The server is running Windows Server 2008 R2 Standard. I must go to the permissions on the server to have new stations to be recognized? The new computers are the replacement of the existing jobs and will be connected to the ports of existing data.

  Thank you.

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet Forum
  http://social.technet.Microsoft.com/search/en-us/Windows?query=server%202008&refinement=1002&beta=0&AC=5

  Hope this information is helpful

• Errors of battery port (PowerConnect 6248 switch)

  Please see the logs below. What is that saying? The question is on the network or physical problem on the cable/port?

  Log buffer:

  Errors detected on the Port of pile 1/xg1 (oldRxErrors = 3001 = currentRxErrors 3003 oldTxErrors = 0 currentTxErrors = 0). Use BRCM_escape_apos; See the battery-port diagBRCM_escape_apos; Watch detailed statistics.

  See the battery port diag:

  1 - xg1:
  RBYT:3e5cfaaa RPKT:9a4ba4b TBYT:e4c25325 TPKT:7d81423d
  RFCs:BC0 RFRG:0 RJBR:0 RUND:0 ROVR:0
  TFCS:0 TERR. : 0

  1 - xg2:
  RBYT:c2277bb1 RPKT:6b2c0473 TBYT:ea7e75d3 TPKT:4b0cf8ae
  RFCS:0 RFRG:0 RJBR:0 RUND:0 ROVR:0
  TFCS:0 TERR. : 0

  2 - xg1:
  RBYT:32f4ae8 RPKT:17590db0 TBYT:dcc05da9 TPKT:330ea6d7
  RFCS:1 RFRG:0 RJBR:0 RUND:0 ROVR:0
  -Other - or ITU (q)
  TFCS:0 TERR. : 0

  2 - xg2:
  RBYT:1e243193 RPKT:7ca8563e TBYT:dce26ec1 TPKT:4bb4d53
  RFCS:15 RFRG:0 RJBR:0 RUND:0 ROVR:0
  TFCS:0 TERR. : 0

  3 - xg1:
  RBYT:670d9fbf RPKT:8553d2af TBYT:82112954 TPKT:b6b0d342
  RFCS:0 RFRG:0 RJBR:0 RUND:0 ROVR:0
  TFCS:0 TERR. : 0

  3 - xg2:
  RBYT:fae703cb RPKT:d9fe988e TBYT:79ddb35 TPKT:b0647900
  RFCS:0 RFRG:0 RJBR:0 RUND:0 ROVR:0
  TFCS:0 TERR. : 0

  4 - xg1:
  RBYT:25865503 RPKT:4f3df21b TBYT:27359088 TPKT:6e8f38a5
  RFCS:0 RFRG:0 RJBR:0 RUND:0 ROVR:0
  TFCS:0 TERR. : 0

  4 - xg2:
  -Other - or ITU (q)
  RBYT:8210be41 RPKT:b6b0d2dc TBYT:670cbb4d TPKT:8553d1cd
  RFCS:0 RFRG:0 RJBR:0 RUND:0 ROVR:0
  TFCS:0 TERR. : 0

  Thank you

  Ok. Finally I found the downtime. We had to add a new switch of the battery.

  I took 1/xg1 cable and put it in the 4\xg1 port to connect to the new switch.

  Also updated to the latest firmware.

  Result:

  -There was no errors for 2 the first 2 days.

  -first 8 mistakes happened today on port 4/xg1

  ------------TX-------------- ------------RX--------------

  Data error data error

  Rate rate rate rate Total

  Interface Unit (MB/s) (errors/s) errors (MB/s) (errors/s) errors

  ---- ---------------- ------ ---------- ---------- ------ ---------- ----------

  1    xg1              554    0          0          288    0          0

  1    xg2              820    0          0          972    0          0

  1    xg3              0      0          0          0      0          0

  1    xg4              0      0          0          0      0          0

  2    xg1              428    0          0          298    0          0

  2    xg2              291    0          0          549    0          0

  2    xg3              0      0          0          0      0          0

  2    xg4              0      0          0          0      0          0

  3    xg1              53     0          0          17     0          0

  3    xg2              295    0          0          435    0          0

  3    xg3              0      0          0          0      0          0

  3    xg4              0      0          0          0      0          0

  4    xg1              971    0          0          821    0          8

  4    xg2              18     0          0          52     0          0

  4    xg3              0      0          0          0      0          0

  4    xg4              0      0          0          0      0          0

  5    xg1              973    0          0          818    0          0

  5    xg2              818    0          0          973    0          0

  ------------TX-------------- ------------RX--------------

  Data error data error

  Rate rate rate rate Total

  Interface Unit (MB/s) (errors/s) errors (MB/s) (errors/s) errors

  ---- ---------------- ------ ---------- ---------- ------ ---------- ----------

  5    xg3              0      0          0          0      0          0

  5    xg4              0      0          0          0      0          0

  It's the fault of physical cable. I have to replace the cable.

  Thank you all for help in the investigation.

• PowerConnect 6248 switch for Cisco router

  Hello

  I'm new to this forum and I have a problem at the moment between a Cisco router and a dell pc6248. The problem is that I lost conectivity in VLAN 1 when I connect the router to a trunk port in the switch, however I conectivity VLAN 2 through this link to trunk. The configuration of the switch:

  interface ethernet 1/g48

  switchport mode trunk

  switchport trunk allowed vlan add 1-2

  output

  interface ethernet 1/g43

  switchport mode access

  switchport access vlan 2

  output

  On router

  fast interface 0/1

  no ip address

  no downtime

  fast interface 0/1.1

  encapsulation dot1q 1 native

  IP 192.200.3.1 255.255.255.0

  fast interface 0/1.2

  encapsulation dot1q 2

  IP 192.168.51.33 255.255.255.248

  output

  With the above configuration, I lost conectivity with the host in the vlan 1 - 192.200.3.x/24, but I win conectivity VLAN 2, when I connect the router to the 48 trunk port in the switch. This means that the trunk link for VLAN 2 work but not for VLAN 1.

  I read on the port of general mode, where I can configure the pvid of the port as 1 (vlan1) and it would be the unttag VLAN (even natively in Cisco), and I can configure the VLAN 2 like the tag, all this in the same port. What do you think about this? Someone have set up something like that?

  Best regards

  Erasmo

  PD: I write from Chile, I apologize for my English.

  I agree with you, I would try the general mode on the PowerConnect switch.

  mode console # switchport general

  Console # switchport General allowed vlan add 2 tag

  Console # switchport pvid General 1

  Keep us updated.

• The PowerConnect 6248 switch, RAY and selected methodological issues

  I think this should be simple enough, but doesn't work that way. I have multiple 6248 and a handful of other switches in PC and I'm RADIUS deployment as primary authentication mechanism. I'm going through some preliminary tests here and a simple thing is not just to work this way. Profile networklist I put RAY first of all that the method of selection and LOCAL for the second. The RADIUS user authenticates very well, but while trying to search the LOCAL user, it is rejected. I thought that if the local user is not found by DEPARTMENT policy, he is sent to the next method? I'm only using telnet for the moment method before changing the HTTP methods. Any thoughts would be appreciated. Thank you!

  Could answer my own question here, but I think that the NPS server should probably 'time' or not meet the demand of the initial authentication for the local aspect until you reach? have not tested, but may do so shortly.

• N2048 vs PowerConnect 6248 switch

  Hello

  I would like to ask the professional.

  For the communication of internal servers of our company, what to spend more powerful N2048 or PC6248?

  We would like to use only ports of the team, LAG. No VLAN, no routing. Just "layer 2".

  Thank you.

  Best regards

  MAxim Krol

  Hi, Maxim,.

  If you do not give me layer 2 the N2000 is the newer model. It has several CPU memory 1 GB vs. 256 MB and increased capacity of fabric and a faster transfer rate.

  http://www.Dell.com/us/business/p/networking-N2000-Series/PD

  http://www.Dell.com/us/business/p/PowerConnect-6200-series/PD

• Adding a new parent entity is in conflict with existing parent adjustments

  Hello people,
  
  I am trying to add a new parent entity in the entity dimension, but get an error message when loading the metadata. The message basically says that there is some adjusting parent entries exist for this new parent children and, of course, the conflict arises with the new parent.
  
  How can I go about it? I don't want to remove these magazines to fit existing parent so not to disturb the earlier codifications.
  
  Help, please!
  Any ideas would be greatly appreciated!
  
  Kind regards
  
  Polina Kornyukhina, Toronto
  Upper Lakes Group Inc..
  416-960-4416.

  I would create a new entity just below the initial parent. Then change all entries for this entity (and not Parent Adjs). Then add your new parent entity and move the members of base under him. It should preserve the old numbers while allowing the living structure of the future State.

  As a general rule, I guide people away from Adjs Parent whenever possible.

• Good method to restore running, boot and Firmware for PowerConnect 6224 switch

  Hi all

  I have a switch PowerConnect 6224 of production that is configured exactly as I want.  I have a new PowerConnect 6224 switch I want to restore the config is possible?  My goal is to not have to manually enter settings for each single switch.

  I tried a few methods, but they do not seem to work.  If anyone can tell me the correct procedure or point me in the right direction would be great!

  Here's a document on some older switches which explains the process.

  www.Dell.com/.../app_note_12.pdf

  It is different for the 6248 somewhat, but the concept is still the same.

  Copy of the file Image of a server to Flash memory

  Use the command copy of the image - the url of the source to copy an image from a Flash memory server file, use the boot system command to activate the new image.

  Copy of a Configuration file from one server to the running Configuration

  Use the running-config command to copy the url of the source to load a configuration file to a network server for the device running configuration. The configuration is added to the running configuration, as if the commands were typed in the command line interface (CLI). The resulting configuration file is the combination of the running configuration and the loaded configuration file, with the configuration file with priority.

  Copy of a Configuration file from one server to the Startup Configuration

  Use the command copy startup-config - the url of the source to copy a configuration of a network server file in the startup of the device configuration. These commands replace the configuration file starting with the copied configuration file.

  Store the Configuration of starting or running on a server

  Use the command copy running-config destination url to copy the current configuration file to a network server by using TFTP. Use the copy destination-url startupconfig command to copy the configuration file to start on a network server. The copy of the configuration file can be used as a backup copy.

  firmware download also includes step by step instructions on how to upgrade the firmware.

  www.Dell.com/.../drivers

• PowerConnect 6248 stacking using the front SFP Ports

  I am trying to stack two Dell Powerconnect 6248 switches. Currently they are chained together, but I modules fibre for the front sfp ports. Theoretically, I should be able to stack them. But when I try:

  stack 1/g45 #stack - port console (config-battery)

  Could not set the front panel stacking mode.

  Any ideas? Thank you!

  The PCT6200 requires a stack of modules installed in Bay 1 (XG1 XG2) at the rear of the switch. The stacking module uses CX4/Infiniband type stacking spacers.

  Stacking of front port / user is not supported

• PowerConnect 6248 routing problem

  Hi all

  I have a very frustrating problem with routing using a PowerConnect 6248 switch.

  Network configuration is the following:

  VLAN3

  172.16.0.254/24

  VLAN4

  192.168.0.254/24

  PC on each VLAN using the switch VLAN interface IP (x.x.x.254) as the gateways.

  Switch has configured default route to 192.168.0.248 which is a router with excess of 100 subnets frame relay cloud. 192.168.0.248 has routes suitable for all remote subnets via a serial interface, a static route to VLAN 3 (172.16.0.0/24) traffic through 192.168.0.254 and one way by default via a PIX 515 (192.168.0.253). Router and PIX is connected to access VIRTUAL 4 LAN ports. The PIX has a route to VLAN 3 traffic through 192.168.0.254.

  The problem is that VIRTUAL 3 all hosts on the local network cannot access the Internet. They can ping the gateways in the order - 172.16.0.254, 192.168.0.248 and 192.168.0.253. I have disabled IP forwarding on the router and the switch with no effect.

  I built this configuration in Cisco Packet Tracer 5.0 (it works) and we are running exactly the same IP configuration with a Nortel switch instead of the Dell 6248 (this also works).

  Absoloutely perplexed to find out what I'm missing! I also noticed that if I perform a traceback while in the CLI on the router using a source IP address of the interface VLAN that it blocks the interface on the switch.

  I would be very grateful to anyone who can punch me in the right direction.

  I've included the config switch below.

  Configure
  database of VLAN
  VLAN 2-4
  subnet of VLAN association 172.16.0.0 255.255.255.0 3
  subnet of VLAN association 192.168.11.0 255.255.255.0 2
  subnet of VLAN association 192.168.0.0 255.255.255.0 4
  output
  battery
  1 2 Member
  output
  IP 10.10.10.1 255.255.255.0
  no console logging
  no ip redirection
  IP routing
  IP route 0.0.0.0 0.0.0.0 192.168.0.248
  bootpdhcprelay enable
  bootpdhcprelay IP_serveur 192.168.0.3
  router RIP
  no activation
  output
  interface vlan 2
  name of the "voice."
  Routing
  IP 192.168.11.254 255.255.255.0
  output
  interface vlan 3
  name "workstations".
  Routing
  IP 172.16.0.254 255.255.255.0
  output
  interface vlan 4
  "Name servers".
  Routing
  IP 192.168.0.254 255.255.255.0
  output
  level of 3c9fd59f1a240ff455a9d9e8eebae936 user name 'admin' password encrypted 15
  router ospf
  no activation
  output
  !
  interface ethernet 1/g1
  switchport mode trunk
  switchport trunk allowed vlan add 2-4
  switchport trunk allowed vlan remove 1
  output
  !
  interface ethernet 1/g2
  switchport mode trunk
  switchport trunk allowed vlan add 2-4
  switchport trunk allowed vlan remove 1
  output
  !
  interface ethernet 1/g3
  switchport access vlan 2
  output
  !
  interface ethernet 1/g4
  switchport access vlan 2
  output
  !
  interface ethernet 1/g5
  switchport access vlan 2
  output
  !
  interface ethernet 1/g6
  switchport access vlan 4
  output
  !
  interface ethernet 1/g7
  switchport mode trunk
  switchport trunk allowed vlan add 2-4
  switchport trunk allowed vlan remove 1
  output
  !
  interface ethernet 1/g8
  switchport access vlan 3
  output
  !
  interface ethernet 1/g9
  switchport access vlan 4
  output
  !
  interface ethernet 1/g10
  switchport access vlan 3
  output
  !
  interface ethernet 1/g11
  switchport access vlan 3
  output
  !
  interface ethernet 1/g12
  switchport access vlan 3
  output
  !
  interface ethernet 1/g13
  switchport access vlan 3
  output
  !
  interface ethernet 1/g14
  switchport access vlan 3
  output
  !
  interface ethernet 1/g15
  switchport access vlan 3
  output
  !
  interface ethernet 1/g16
  switchport access vlan 3
  output
  !
  interface ethernet 1/g17
  switchport access vlan 3
  output
  !
  interface ethernet 1/g18
  switchport access vlan 3
  output
  !
  interface ethernet 1/g19
  switchport access vlan 3
  output
  !
  interface ethernet 1/g20
  switchport access vlan 3
  output
  !
  interface ethernet 1/g21
  switchport access vlan 3
  output
  !
  interface ethernet 1/g22
  switchport access vlan 3
  output
  !
  interface ethernet 1/g23
  switchport mode trunk
  switchport trunk allowed vlan add 2-4
  switchport trunk allowed vlan remove 1
  output
  !
  interface ethernet 1/g24
  switchport access vlan 3
  output
  !
  interface ethernet 1/g25
  switchport access vlan 4
  output
  !
  interface ethernet 1/g26
  switchport access vlan 4
  output
  !
  interface ethernet 1/g27
  switchport access vlan 4
  output
  !
  interface ethernet 1/g28
  switchport access vlan 4
  output
  !
  interface ethernet 1/g29
  switchport access vlan 4
  output
  !
  interface ethernet 1/g30
  switchport access vlan 4
  output
  !
  interface ethernet 1/g31
  switchport access vlan 4
  output
  !
  interface ethernet 1/g32
  switchport access vlan 4
  output
  !
  interface ethernet 1/g33
  switchport access vlan 4
  output
  !
  interface ethernet 1/g34
  switchport access vlan 4
  output
  !
  interface ethernet 1/g35
  switchport access vlan 4
  output
  !
  interface ethernet 1/g36
  switchport access vlan 4
  output
  !
  interface ethernet 1/g37
  switchport access vlan 4
  output
  !
  interface ethernet 1/g38
  switchport access vlan 4
  output
  !
  interface ethernet 1/g39
  switchport access vlan 4
  output
  !
  interface ethernet 1/g40
  switchport access vlan 4
  output
  !
  interface ethernet 1/g41
  switchport access vlan 4
  output
  !
  interface ethernet 1/g42
  switchport access vlan 4
  output
  !
  interface ethernet 1/g43
  switchport access vlan 4
  output
  !
  interface ethernet 1/g44
  switchport access vlan 4
  output
  !
  interface ethernet 1/g45
  switchport access vlan 4
  output
  !
  interface ethernet 1/g46
  switchport access vlan 4
  output
  output

  
  

• Incoming packets were discarded on Dell 6248 switch

  Hello guys,.

  I'm having a problem on my network. From time to time the icmp echo packets are lost and this causes our monitoring system trigger false alarms.

  I checked interfaces for switches and found the discarded packet counter is incremented in one of them.

  Flow control is enabled on the interface and there is no frame break sent.

  The duplex on both ends are correct are the port speeds.
  The firmware of the switch is 3.3.9.1 and the model is a PowerConnect 6248 switch.

  view statistics ethernet 1/g48

  Total packets received (bytes)... 2019770477
  Packets received 64 bytes... 945800
  Packets received from 65 to 127 bytes. 1105872
  Packets received from 128 to 255 bytes... 152970
  Packets received 256-511 bytes... 445738
  Packets received 512-1023 bytes... 155436
  Packets received 1024-1518 bytes... 414040
  Packets received > 1518 bytes... 634118
  64 bytes of RX and TX packets... 946019
  RX and TX 65-127 bytes packet... 3294655
  Packet RX and TX 128 to 255 bytes... 235082
  RX and TX 256-511 byte packets... 893732
  RX and TX 512-1023 byte packets... 311408
  RX and TX 1024-1518 byte packets... 436671
  RX and TX 1519-2047 bytes packets... 873826
  RX and TX 2048-4095 bytes packets... 0
  RX and TX-9216 4096 bytes packets... 0

  Total packets received without errors... 3853974
  Unicast packets received... 3421088
  Received multicast packets... 211575
  Received broadcast packets... 221311
  -Other - or ITU (q)
  Receive packets ignored... 506

  Total packets received with errors of MAC... 0
  Jabbers received... 0
  Fragments / sousdimensionnés has received... 0
  Alignment defects... 0
  FCS Errors..................................... 0
  Overruns....................................... 0
  802. 3 x Pause frames received... 0
  Unacceptable frame type... 0

  Total of transmitted packets (bytes)... 858789293
  64 byte packets transmitted... 219
  65-127 bytes transmitted packets... 2188783
  Packets transmitted 128 to 255 bytes... 82112
  256-511 bytes transmitted packets... 447994
  512-1023 bytes transmitted packets... 155972
  1024-1518 bytes transmitted packets... 22631
  Transmitted packets > 1518 bytes... 239708
  Size of the image of max... 1518

  Total packets transmitted successfully... 3137419
  Transmitted unicast packets... 3034928
  -Other - or ITU (q)
  Multicast packets transmitted. 1628
  Broadcast packets transmitted. 100863
  Transmit packets ignored... 0

  Total transmit packets ignored... 0
  Single Collision frames... 0
  Several images of Collision... 0
  Excessive Collision management... 0

  802. 3 x Pause frames transmitted... 0
  GVRP PDU received... 0
  GVRP PDUs of transmitted... 0
  GVRP failure records... 0
  BPDU: 0 sent, received 0

  EAPOL frames transmitted... 0
  EAPOL Start received frames... 0

  Thanks in advance.

  Humm,

  We have changed our duo of remote of a failure wan link and the interface mistakes of count stop. Everything is the same: traffic, applications, etc. Not a clue about what happened because there is a Linux between the equipment of the carrier and the switch (bad packets would have fallen in the interface of linux machine).

  We turn now to the carrier of the explanations/solutions.

  Thank you for your time!