After a power outage, I can't start after the Windows XP logo.

Similar Questions

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• I can only start using the list of Windows XP

  Original title: WINDOWS XP STARTUP W/DISC PROBLEMS

  I have a problem starting my desktop xp computer. I can ONLY start with the XP disk, of course, I have to press 'R' over and over again. After a few tries, it starts well, how can I start up without having to redo this process over and over again. I passed by 'MSCONFIG' and past from NORMAL to SELECTIVE startup and even deleted some programs from my hard drive. I can't make changes without putting in my (domain name Name\Administrator). I don't know what could be and am lost at this point... HELP!!!!!!!!!!!!!!!!

  THOMAS

  Hi Thomas,

  ·         Did you do changes on the computer before the show?

  ·         You receive an error message or error code?

  Follow the suggestions below for a possible solution:

  Method 1: Remove all external devices connected to the computer such as printers scanners or USB external hard drives and restart the computer and check if you receive the error.

  Method 2: Try to start the computer in safe mode with network and check if the issue still persists, see the link below to start in safe mode.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

   

  Method 3: You can try and perform a system restore to a date when things were working well and check.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  In addition, you can also download the minidump files so the experts here can analyze the cause of the problem.

  How read partial memory dump files that Windows creates for debugging

  http://support.Microsoft.com/kb/315263

   

  Use SkyDrive download collected files and post screen shot/image

  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  Let us know the results.

• I have Windows vista Ultimate edition. but he started asking for activation after the windows update while it has already been activated before the update.

  I have Windows vista Ultimate edition. but he started asking for activation after the windows update while it has already been activated before the update.

  Hello, Pichon,

  If Windows Vista application unexpected activation

  On rare occasions, you may be prompted to activate Windows Vista on a computer that did not previously require Windows Vista activation or has already been activated successfully. For example, this may occur on a computer on which Windows Vista was preinstalled by an OEM installation or Volume licensing and are major hardware changes occurred, such as upgrading the hard disk and memory at the same time.

  If you are prompted to reactivate Windows Vista, you can do this by using the Windows Activation Wizard to:

  1. Click Start, and then click computer.
  2. Click System Properties on the toolbar, and then click click here to activate Windows now in the Windows activation area. If you are prompted for an administrator password or a confirmation, type the password, or click continue.
  3. Select the Windows Vista activation method that you want, and then follow the instructions.

  To avoid this problem in the future, obtain the latest service pack for your version of Windows Vista, either through automatic updates or direct download.

  To update to Windows Vista and prevent this activation problem does not happen:

  1. Click Start, click all programs, and then click Windows Update.
  2. Click find updates.
  3. As soon as Windows Vista found the updates, click the install updates button.

  How to activate Windows Vista

  http://support.Microsoft.com/kb/940315

  Activation fails when you try to activate Windows Vista, Windows 7, Windows Server 2008 or Windows Server 2008 R2 on the Internet

  http://support.Microsoft.com/kb/921471

• After the Windows 8.1 update, can not access Internet in Firefox or Chrome, but IE 11 OK.

  After the Windows 8.1 update, can not access Internet in Firefox or Chrome, but IE 11 OK.
  I reinstalled the latest firefox, still cannot access Internet from Firefox.
  Microsoft is ridiculous?

  1. Run cmd.exe as administrator
  2. Type "netsh winsock reset" and then press enter
  3. Restart the PC

• HP Pavilion dv6000 (Vista) starts with a blank screen with a cursor after the original hp logo screen.

  HP Pavilion dv6000 (Vista) starts with a blank screen with a cursor after the original hp logo screen.  Cannot get it to boot Windows.  Any thoughts on next steps?

  I remove the hard drive and attach it to your desktop and use the host operating system to run a check disk on your drive.  The laptop goes hard disk looking for instructions to start and he does not see the correct code.  This is probably due to a damaged boot sector.  Another idea is that your bios has changed and you have changed the SATA from AHCI to IDE type somehow or vice versa. You also left a non bootable disk in the DVD/CD drive.  Remove all disks from your DVD.

• Can not activate Adobe Acrobat 7.0 standard after the window 10-any solution?

  Can not activate Adobe Acrobat 7.0 standard after the window 10-any solution?

  Acrobat 7 is not compatible with windows 10.

  I recommend you upgrade to Acrobat DC. (Plans and price |) Adobe Acrobat DC )

  Kind regards

  Rahul

• Network icon is missing from the notification area after the window updated

  I have some problems about the notification for the network and the volume icon!
  They are missing after the window updates!
  I tried to check the "Taskbar and Start Menu Properties' > 'Notification area', Volume and network are grey which I cannot check these boxes. Grateful if you could help me solve this problem!
  Thank you very much!

  Hi VisBo,

  Welcome to the windows vista forums.

  Please follow the steps below to resolve this issue:

  1. right click on the taskbar and click Properties.

  2 tab Area of Notification .

  3 check (on) or disable (off) the options you want or do not want to display on the Taskbar Notification area.

  For the network icon, you can also do with the registry.

  NOTE:

  Please be careful while making changes to the registry, any undesirable changes can affect your operating system.

  1. click on start.

  2. in the start menu search bar type regedit, and then on enter.

  3 Please go to this location in the registry by expanding each location by clicking on the brand more on the left side.

  HKEY_CURRENT_USER\Software\Classes\LocalSettings\Software\
  Microsoft\CurrentVersion\TrayNotify

  4. remove the keys 'IconStreams' & 'PastIconsStream '.

  5. start the Task Manager by pressing ctrl + alt + delete at the same time.

  6. in the Task Manager right click on explorer.exe and kill the process.

  7. click on applications in the task manage, press new task and type explorer.exe, and then press ENTER.

  Explorer will now reboot and your icons should return.

  Alternatively, you can try to uninstall the most recent update that has caused the problem. You can uninstall an update by clicking on the icon of the program features in Control Panel. Select the update that caused the problem, and then uninstall it.

  You can also make a selection of updates to install by setting the windows updates to notify you before installing an update. To open this Panel, and then click windows updates, click settings.

  I hope this information is useful.

  Please let us know if you need assistance.

  Concerning
  Rehman - Microsoft Support

• I can't pull up the Windows Media Player on my computer, when I click the icon, nothing happened. Who is wrong?

  More I can't pull up the Windows Media Player on this computer. When I click the icon, nothing happened, what / s wrong?

  Hi Thomas,

  1. you receive messages or error codes?

  2. when the problem started?

  3. did you of recent changes on the system?

  Method 1:

  You can run the Fixit from the following link and check if it can solve the problem.

  Solve the problems of Windows Media Player video and other media or library

  You can also read the following article and check if it helps.

  Windows Media Player stops responding after you install a third-party product that registers its own version of the Wmp.dll file

  Method 2:

  If you still experience the problem, you can perform a clean boot and check.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  After the troubleshooting steps, please clean the start link to put the computer to normal startup mode

  Hope this information is useful.

• G62 screen remains black after the windows logo

  Hello

  I have a HP G62-b05SD. I noticed that many people have the problem of simmular.

  I know what makes, but don't know how to fix it.

  So here it is.

  Sometimes when I boot / reboot system screen turns black after the windows logo, but if I wait a while, I do not hear the star tune up windows, but the screen remains black.

  I noticed that this happens when I shut down or restart the system with a usb port (be it a mouse or a stick is not serious)

  If I all out en usb port restart or turn on the machine for the first time this day here, everything starts well.

  So there must be some driver problems I think with usb ports and the screen or something.

  Help, please!

  HP G62-b05SD

  Windows 7 64-bit

  Intel i3

  ATI mobility radeon graphics card

  Ow and when I get the black screen, the hard reset does not always work.

  I also did a startup repair and it showed:

  "If you have recently attached a device to this computer as a camera or portable music player, remove it and restart your computer. If you continue to see this message bla... bla... bla... "

  I hope you can help.

  Hi Frosty1984,

  Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP G62 - b05SD Notebook and having problems with the starter. Here is a link to BIOS update.

  What is the USB device that is at the origin of the questions?

  Thank you.

• How can I boot from the Windows 7 Installation CD so that I can reformat the hard drive before reinstalling Windows 7?

  How can I boot from the Windows 7 Installation CD so that I can reformat the hard drive before reinstalling Windows 7?  I have already reinstalled Windows 7 from the CD, but that has not solved my problems.  When I put the factory CD in my CD player, it won't always boot from the CD.  When I put my Windows 7 Ultimate CD in the CD drive, it doesn't always start from the CD.         I realize that the reformatting is not always necessary, but I caught a few viruses (despite anti-virus running) and I need to start with a clean hard drive.

  On Friday, January 9, 2015 14:30:32 + 0000, BlueKodak wrote:

  How can I boot from the Windows 7 Installation CD so that I can reformat the hard drive before reinstalling Windows 7?  I have already reinstalled Windows 7 from the CD, but that has not solved my problems.  When I put the factory CD in my CD player, it won't always boot from the CD.  When I put my Windows 7 Ultimate CD in the CD drive, it doesn't always start from the CD.

  You must go into the BIOS and change the boot on CD order
  first push.

  How to get into your BIOS? It is not dependent on Windows, but on what he
  motherboard/BIOS card that you have. In fact, you need access to the
  BIOS before Windows begins to start. A common method is to press
  the key delete when you turn on first, but this is not necessarily true
  for your computer. Watch the display carefully when you start first;
  There is often a message here to tell you what to do. If this is not the case, check
  your system documentation or check with your provider.

• My computer is clearly marked with the Windows 7 Logo, but works under XP, can you explain this? IM lost

  I have a HP Probook 6545 B, which has the Windows 7 logo plastered everywhere. However, when starting, shows that it is indeed NOT running Windows 7 instead, running on Windows XP. Why is this? Is it possible that it can be 'cancelled' or restored to this OS somehow? Windows 7 is stored in a hidden file of OS on my hard drive of the computer somewhere? If so, how caould I find and restore dump XP and 7?

  You bought the new laptop or used? Most of the business line of laptops come with Windows 7 had the possibility to order with the downgrade to XP, if you wish.

  Click here >Contact HP to order Windows 7 recovery discs to change the OS.

• USB mouse & keyboard disabled randomly after the Windows 7 login Panel

  Hi all

  Randomly, after the Windows 7 login Panel, windows disables my keyboard and USB mouse.

  -No problem in BIOS or on the login Panel, but once the credentials entered and valid, and reaching office, mouse and keyboard (USB) close

  -To solve the problem, I need to reboot several times, waiting for an instance where my devices are not closed (so it works without any pb until the next reboot)

  -J' have a backlit keyboard and when the problem occurs, light are turned market, as if it was turned on and turned off randomy

  Searching the Internet, seems, I'm not the only to encounter the problem, however single chip found Advisor on these was mentioning it is a bug in Microsoft Windows 7, associated with the management of the power supply of the USB ports. However the advice provided to change the config to disable these judgments do not work...

  Thanks in advance for your help and best regards

  Fabrice

  Have you tried to go to safe mode with networking Mode and update your USB drivers?

  You didn't say you had the problem goes mode without failure, so it might be a solution for you.

  USB drivers should be found at the web page of the manufacturer of your computer or your motherboard manufacturer's web page.

• I can't disable WPAD (the windows proxy automatic detection) on my Windows 7 HB32.

  Hey guys,.

  I can't disable WPAD (the windows proxy automatic detection) on my Windows 7 HB32.

  In connection settings I have to disable the option "automatically detect connection settings", but after some time (or two days), this option becomes available again.

  Is it possible to completely disable WPAD on Windows 7?

  Thank you

  Anton.

  Hello

  Have you made changes on the computer before this problem?

  I suggest you to go through the following method and the Coachman.

  How to disable the automatic proxy caching in Internet Explorer. http://support.Microsoft.com/kb/271361

  Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows.

• Inspiron 9300 screen turns off after the Windows Logo screen

  Inspiron 9300 my wife became severely infected.  I thought I had some weird things start popping up of the problem decided to wipe the hard drive and start over.  Unfortunately, I don't have to restore disks when I bought the computer.  I install windows xp pro service pack 2 full retail version.

  Installation was not a problem until I installed the driver ATI Mobility x 300.  I followed directions for installation from the website, do the installation of xp followed of the dell system software update followed of chipset followed video driver.  After that whenever I put on, the screen turns off after the Windows Logo.  The computer is still running and if I plug an external monitor everythng is fine.

  I tried all the troubleshooting tips I've seen in this forum.  I did a full install twice. made of safety boots (all right), started in VGA mode (works fine), I ran diagnostics from fn on startup, including express, extended and video tests and they pass all the controls.  I'm sure it's a software problem, but have been unable to solve.  I've updated the ATI bios although when I run it says already installed and done one installs x 300 driver on 6 ttimes own.

  I know it must be something simple that I'm missing. My system is the Inspiron 9300 with 2 GB of ram and the mobility x 300 card.  Any help would be appreciated.