After installing winows xp SP3, cannot connect to the network wireless at home

Similar Questions

• Cannot connect to the network after updating to iOS 9.3 Beta

  I downloaded and installed the public beta version of iOS 9.3 on my iPhone 6 today. After that, I am unable to connect to the network. I tried to reset the network connection of the phone and have my cell phone operator reset the network connection. None worked. Anyone else have this same problem?

  I was able to solve the problem by turning on "Airplane Mode" for 5 seconds, then shut off again. Everything seems to work fine now.

• "Cannot connect to the network." When you enter the correct password for wireless network

  Hello

  I have the HP Photosmart C7200 all-in-One series.

  This seems relatively insignificant compared to some of the problems posted here, but nevertheless it is a problem.  I have a Verizon FiOS (Actiontec) router.  I am trying to connect to it wireless; the network key is using WPA authentication.  I followed all the instructions in the quick start guide.

  My printer detects my network and application authentication key.  I enter the correct key, the printer is trying to establish a connection, but after about 15 to 25 seconds, I get the error message, "cannot connect to the network.  I know that my key is correct; I connect to my router very well through several laptops, PDA, etc.  I have reset the settings network default manufacturer and tried without success.

  I don't know what kind of trouble shooting I'm supposed to do here.  The printer detects the router (albeit low signal strength) whenever I try to connect, I enter the password each time and I get the error each time.

  Your help is greatly appreciated.

  Edit: I printed the test report wireless network, here are the results:

  Radio on   PASS

  The radio work   PASS

  Ethernet cable not plugged in   PASS

  Network name (SSID found)   PASS

  Security   PASS

  The printer settings compatible with the configuration of the wireless router   PASS

  No filtering   IN CASE OF FAILURE

  Connected   Not work

  The signal strength   Very low

  Other networks detected matching you the network name (SSID)   NO.

  I know this sounds strange, but try changing channel by channel 11 of the wireless router.

• Comments Win XP cannot connect to the network when Cisco VPN works on Mac

  Guest OS (Win XP) on the merger connects to the network, no problem. However, when I start a Cisco VPN on my Mac (not in the guest operating system) and then start Fusion/guest OS, the guest cannot connect to the network.

  I was able to use this configuration for a year on an old MacBook Pro (unibody). Last month, I got a new MacBook Pro and flying over my virtual machine image. I don't check for a few weeks. I'm sure I fly over the image correctly because everything else seems OK or if the IT guys doing something to block my traffic over the VPN.

  Config

  -Fusion - Version 3.1.0 (261 058)

  -Mac - 10.6.4

  So far, I have tried the following

  -started to merge and XP without VPN on Mac - OK (bridge autodetect)

  -launched VPN to work, and then launched Fusion - no network

  -tried ipconfig/release, ipconfig / renew - not always no network

  -tried NAT - do always no network

  Thanks in advance. For any help or suggestion will be greatly appreciated.

  Bernie

  The NAT value and then restart the virtual machine.  Works for me with the VPN client built into a cisco router.

  Do not work the real on 10.6.4 cisco software unless you really need to.

• I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  original title: WiFi

  I can't connect to the network wirelessly with my Emachines eM350 portable because I get the automatic Wireless Configuration error, see Article 871122.

  I use a Huawei E585. I simply want to clamp it alll in the tray.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  (1) make sure that u run "NET START WZCSVC" on the command-line as soon as u Ouvrezunesession WINDOWS XP (START, RUN, NET START WZCSVC (command line)).

  (2) START, CONNECT, WIRELESS INTERNET CONNECTION

  --> under the 'GÉNÉRAL' tab: (1) right click on the wireless Internet connection; (2) click on properties; (3) make sure that all THE ELEMENTS under the title "THIS CONNECTION USES THE FOLLOWING ITEMS" are COMPLETELY FUNCTIONAL, i.e. UNCHECK THE ONES THAT DO ARE NOT ACTIVE ~!  (I recently turned off AVG and that this item has been inadvertently clicked on ~!) ;

  --> on the 'ADVANCED' tab: run the NETWORK CONFIGURATION WIZARD to reset your network

  3) http://support.microsoft.com/kb/871122 --> RUN 'DIFFICULTY CE PROBLEM' (ms - fix 50469)

• I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  Try this below and see if it help you.

  http://support.Microsoft.com/kb/871122

• Computer connects to the network wireless as "local only".

  I am running Vista Home Premium SP2 on a HP Pavilion laptop.  I've never had any problems to connect this machine to a wireless network before, in hotels, at home, or anywhere.  My current home network is a modem - cable-> wireless-> wireless netgear n300 router.  My laptop connects to the internet via the modem cable directly or a wire from the netgear router.  I have a second, almost cell identical (it's intel, while the one who does not is AMD) which connects to the network wireless without any problem.  Two iphones connected wirelessely without any problem.  My HP laptop is the only one who refuses to connect to the internet.  Connected to the wireless network, it has access "local only".

  I tried the solution in this article: http://support.microsoft.com/kb/928233

  The question does not seem to receive an ip address, the computer receives an ip address.  I have disabled the IP v6, ran the norton removal tool, because I only had to a point and tried all other suggestions in these discussions: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/0949042d-074e-43ab-ba95-3c06cc2aa6be and http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/bc08f0e7-49a9-4458-9e0e-149b2df362ec.  I've uninstalled and reinstalled the adapter and all TCP/IP and network protocols associated with it.  I am at a loss and would welcome any ideas.

  Here is the result of the command ipconfig / all:

  Windows IP configuration

  Name of the host...: Arrakis

  Primary Dns suffix...:

  Node... type: broadcast

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1E-4C-B2-32-BC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.5 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Wednesday, 28 April 2010 21:40:55

  End of the lease...: Thursday, April 29, 2010 21:40:55

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: NVIDIA nForce Networking Controller

  Physical address.... : 00-1B-24-FA-DA-80

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 10:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {31C080CE-FE0B-4D50-B734-C782C9A25FBC}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {B198B0D3-B70A-4E3E-858D-9774C414EECD}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  If anyone has this problem, it has been resolved by rolling the security settings on the router WEP.  I got the answer from the support client netgear.

  Amazing how two iphones, another laptop with XP and a laptop running Ubuntu Linux all about them without any problem, but wouldn't connect Vista laptop.

• Cannot connect to the network or perform system restore after installing updates have been

  WIN 7 Home Premium running on a gateway PC connected to the internet via an ethernet connection using a RealTek network adapter for the past 5 years with no problems. Running Avast Pro antivirus / internet security.  09/02/2016, Microsoft and Avast downloaded and installed updates on the PC.  After the PC auto-redémarré as part of the Microsoft updates, I couldn't connect to the internet.  Connect to the network now says unidentified network - no network connection.  The adapter looks like to she always sees the (watch 100 Mbps) connection, but no data packet move.  Device Manager indicates that the unit is working normally.

  I ran through the resolution of the problems of Windows network. I checked the cable was attached, reset the home modem, reset the adapter (toggle), uninstalled/reinstalled using the latest adapter driver available.  I have disabled the Windows Firewall because Firewall Avast wouldn't start.  I disabled all the Avast settings to see if it eliminated the problem.  I tried to run the system restore before the updates but continue to spread the message that there was an unexplained error and restore failed.  All this was done in Normal mode. I restarted mode safe and had the same problems without success.

  I was able to clear the problem by manually uninstalling updates of security Windows which were loaded on 09/02/2016 through the programs and features Control Panel. Then I did the repair of Avast program operation.  I rebooted the computer and the internet connection worked. Then I reinstalled manually updates Windows security on the Windows Update program.

• Satellite P300 - after Intel WLAN driver update cannot connect to the WLAN N

  After 4 months I have updated the driver for the WLAN. After installing the driver I m unable to connect to a network of N. recovery software but is not be able to connect to the network.
  I have already installed the Intel driver but nothing help.
  Are there some people who can help me solve this problem?

  I have a Satellite P300.

  Hello

  Firstly, it must ensure that your wireless network card and your WLan router would support the Draft N.

  Second, you should check if the project has been selected in the WLan card properties.
  This, to check the Device Manager-> properties-> Advanced tab WLan card

  Check it out

• HP OfficeJet Pro 8610: Printer cannot connect to the new wireless network

  I got the OfficeJet Pro for a while and everything worked very well (including wireless printing from my Mac and iPad AirPrint). Yesterday, we got a new Modem Router (from Ubee). As I tried to connect the printer with the new network, I fail miserably.

  Here's what I've tried several times: on the small screen of the printer, I select: Network Setup > wireless setting > Wireless Setup wizzard. The printer seems to networks, find the network and asks me the password, I get the password (I did this several times, so no typos!). The printer then "trying to connect to the network"... then it crashes: for a very short moment, I get a blue screen with a white error code (not always the same, for example.) B3FF3802) and then the message "error in the printer, turn off the power, then press.

  I turned off the printer and turn it back on several times (incl. pulling out the power plug and restart after a while), but when I go through the steps above, but I just get the same endresult.

  I deleted the old network as I feared it might interfere with the creation of the new network. No noticeable effect.

  I printed the "results of the wireless network test," which confirms that "your HP printer is unable to connect to your wireless router. In the results of the diagnosis, he states that 'network name (SSID) was found - Fail.

  I quite understand the message that the printer detects the network and shows good SSID / network name. I thought to enter the SSID manually but can't find where I could do.

  I'd be very grateful for any suggestions on what could be the problem (I can't imagine that the printer would not work with a new router... I searched the internet and found stuff on 'Hello compatibility', but do not know which is the issue I'm facing.

  Thanks for your help!

  I brought your question to the attention of a team within HP. They are likely to ask for information from you to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers.

  If you are unfamiliar with the operation of the function of private messages of the Forum, this post has instructions.

• Windows 7 Pro cannot connect to the network when idle too long (large company)

  We have approximately 75 users on Windows 7 Professional.  About two weeks ago (and the next day, Windows updates have been deployed to all PCs in our outside IT), the vast majority of users (but not all) have started to have a problem in what they can connect first thing in the morning; However, they immediately get an error that are not connected to the network, that network drives can be connected, they cannot access the internet, etc.  A reboot solves problems and the problem will not recur until the computer is left idle during the night.  Our outside IT says that what is happening on several client sites that they manage, but they have no idea of the cause; they are theorizing that it's maybe a botched Windows Update.  I have Windows 7 Pro at home and did not have the problem once.  Any suggestions appreciated.

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Photosmart HP 7510: hp Photosmart 7510 says it cannot connect to the network

  I can still print to the printer wireless to my computer, but when I try to FAX directly from my all-in-one he says that it is not connected to the network.

  When I check the settings, it IS connected.

  I had this printer/FAX/scanner for several years now and never had this problem.  I did not make any changes.

  I have unplugged it & tried... still can't FAX.  But I CAN always print it from my PC.

  Help!

  Hello @dtinstl!

  Thanks for posting on the HP Forums!

  Do to an eFax problem and some HP printers supporting the eFax service there is not much I can help in this regard.  I'll have to refer you to this post with instructions on what is done about this particular issue.

  Please see the message here: eFax explanation

  If you wish you can also contact our HP Cloud Services Department in this respect.  Please contact our Cloud Services at 1-855-785-2777.  If you do not live in the United States / Canada region, please click the link below to get help from your region number.  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

• Printer cannot connect to the network

  Hello

  I have a photosmart HP 5510 printer - connected to 2 laptops.  Everything worked fine until I finally made a secure network and has not worked since.  I tried add the mac address of the router and all kinds of things and have no idea what to do next. Any suggestions?   I can go as far as to put in my ssid and password in the printer connect but still says 'unable to connect to the network.

  OK, more ideas.  Remove encryption between the router and connect the printer.  From the front of the printer to allow Web Services and see if there is an update for the printer.  Leave it to update.

  When it's done, re - activate the encryption on the router and try again.  It may be a bug in the firmware in the printer (although I doubt - he would have caught in tests).  I still think that his router, but...

• HP Color LaserJet CP1525nw: Can't get CP1525nw connected to the network wireless Netgear Nighthawk x 6 R8000

  I have never been able to successfully get the printer installed by wi - fi with any stability, so we always connected via USB and shared. I bought a new router and would like to be able to print to this printer wireless anywhere on my network. I can't out of connected mode and mode wi - fi printer. Your software crashes, crash facilities to half way through. The printer indicates an IP 169.254.xxx.xxx, if the network is aware, but it's I can get. None of the HP tools will run under this operating system, they hang immediately upon launch. It's frustration none! Someone out there was a bit of luck with this printer!

  Dell XPS 8700 16 GB of RAM

  Earn 8.1 (64-bit)

  Comcast TG862G Gateway (POS)

  Router wireless Netgear Nighthawk x 6 R8000

  HP LaserJet CP1525nw color printer range

  Hi @jrmunn ,

  I want to help you get the printer works on the wireless network.

  There are a few different ways to install the printer on the wireless network.

  • Thanks to the support WPS.
  • Through the installation, by connecting the USB port, it will configure the wireless.
  • Once the USB installation is done. You can configure the wireless via an Ethernet connection.

  Cycle power to the router.

  First, we must restore the defaults on the printer.

  Press the OK button on the printer, go to the service, and then select restore default settings.

  Print a printer configuration page to make sure that the IP address and SSID are erased.

  Print a Configuration report.

  Uninstall the printer software.

  WPS configuration method:

  To connect your printer to your wireless router wireless using WPS:
  (your router must support WPS)

  Start the mode of the WPS button on your printer.
  Within 2 minutes, press the WPS button on your router.

  Then run a printer from devices and printers Add Wizard.

  The USB method:

  Perform a clean boot on the computer and disable the Antivirus software and any analysis in real-time in the Antivirus software also. How to perform a clean boot in Windows.

  Then run the installation immediately after connecting the USB cable, follow the steps described in this document to update the drivers so that's not new error. A fatal error during Installation of the software. Then the installation should continue. (you can use this procedure for any type of installation)

  If you are still having problems and you have an Ethernet cable, we can install the printer as a USB connection again and then configure the printer via wireless Ethernet.

  Method of Ethernet:

  Restore the default settings of the printer.

  Connect the printer to the router with an Ethernet cable.
  Wait about 1 minute and the printer must have a valid IP address.
  Print the configuration page to get the IP address of the printer.
  Type the IP address in the address bar of Internet Explorer which should open the printer's built-in web services page.
  Installing wireless over here now.
  Click the networking, wireless on the left, fill in information about the network and apply the settings.
  After the confirmation, then disconnect the Ethernet cable.
  Now you should have a flashing light on the printer in 1 minute wireless about.

  Print a printer configuration page, to get the new IPv4 address.

  Then create a new port with the new IPv4 address.

  In the devices window and printers, click right on the printer and on the left, click on printer properties, select the Ports tab.

  Click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.

• Vista - limited - connectivity cannot connect to the internet (wireless)

  Hello

  Okay, so my situation here.

  I can not connect to internet on my Dell Inspiron running Vista. It happened about two weeks ago. I have an Intel Wifi Link 5100 AGN.

  I know for sure, is not my router or my wireless laptops. I can run Linux (on a flash drive, no dual boot) just fine and it recognizes everything perfectly. It doesn't matter if I'm at home or on campus. I can not connect anything.

  I suspect I've changed some settings, like all the it started happening shortly after that I was playing with the Linux CLI. When I booted into Vista, I could not connect.

  I tried Googling and can't find a clear answer. Maybe my DHCP or IP settings are confusing? I think I have to delete some registry keys, or something... not too sure.

  I tried this:

  http://support.Microsoft.com/kb/299357

  Nothing helps.

  Any questions of clarification let me know. Thanks in advance.

  RootCommand

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Go to the Dell Web site > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.

  See you soon.

  Mick Murphy - Microsoft partner