After logging on my Satellite Pro only black screen and the cursor are visible

Similar Questions

• Satellite Pro C660 - black screen and a cursor flashing during startup

  When my laptop start, after it shows the press f2 or f12 and then from windows, it goes to a black screen with the cursor blink.

  The lights are on at the front, but there is no activity on the hard disk, such as the indicator light does not blink.

  Need help. Thank you.

  I think that your HARD drive is dead.
  You need to replace the HARD drive with a new 2.5 SATA HDD.
  Replace the HARD drive and install the OS by using Toshiba recovery disc.
  I hope you ve created one in the past

• Satellite Pro L450D black screen and will not respond to any keys

  Hello

  My niece has used his Toshiba L450D for almost a year now and he really liked it, who was until last month. She turned on her laptop and when she presses the button of the mouse, the button cracked and he fell into the laptop.

  Now my brother contacted Toshiba and I was told because it is under warranty it might return for repair because it was a common fault. Then he he packed in loads of air bubbles and a box to make sure it was safe.

  A few weeks later he came back repaired but we were all shocked that the laptop was put in a very loose box and you could hear this rattling noise. When we turned on the battery was flat and we had a new boot menu.

  As she installed it Windows 7 laptop would boot directly into Windows 7, but now after the repair of the laptop shows a menu black screen with as follows:

  + Windows 7 +.
  + Recover Windows to Factory Settings [active EMS] +.

  So we started in Windows and everything went well, but now after 5 or 10 or even 20 minutes, laptop displays a black screen and will not respond to keys or mouse movement. There is nothing on the screen its just black.

  I started in SafeMode (which was more difficult with the new menu) and it does the same thing. I even managed to do a virus scan quick who took 3-4 minutes and was clean.

  I would like some advice on what my niece is very angry, and it's difficult to explain what is happening to a child in the primary school.

  Any help would be grateful.

  Hello

  Have you tried the option of HARD drive recovery?

  If this is not the case, try to set the notebook back to factory settings using HARD drive recovery.
  Turn on the device, press F12, choose repair my computer, then select Toshiba HDD recovery.

  I hope it will work!

• Windows 8 black screen and the cursor after the connection

  Hello. I tried to upgrade to 8.1 Windows 8 Windows and it is stuck on like 3% for one hour, so I just rebooted the computer and he returned to Windows 8. I'm going to sleep and come back the next day and go on my laptop and it auto connects me and it goes to a black screen and I only have the slider on the black screen after login. I don't see the start menu, but I receive notifications for as sticky keys or any other notifications lights. I turned off my computer at least 20 times, took out the battery, empty the battery and tried to boot in safe mode with no luck. It is unlikely that it is an internal problem, because if I leave my computer alone for a few minutes, my screen saver photos appear. If anyone can help me solve this problem or help me get in easier safe mode would make things less stressful. I have an Acer Aspire V5 - 571 series. Thank you.

  Hi Roy,

  This problem may occur because of corrupted on the computer boot files.

  I suggest you to perform the checking and automatic repair if this solves the problem.

  If you do not have a DVD of Windows 8, I suggest you check out the link to see how to create an installation of Windows 8 media:

  http://Windows.Microsoft.com/en-in/Windows-8/create-reset-refresh-media

  Follow the methods suggested below:

  Method 1:

  Start on the recovery environment using the installation of Windows 8 media.

  Follow the steps below:

  Note: before proceeding further, make sure that the boot priority is set on DVD drive in BIOS. BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  • Insert the DVD to install Windows 8 on DVD-ROM and restart your computer.
  • After you start your computer by using the Windows DVD or the system repair disc, a black screen is displayed with the gray text "Press any key to boot from CD or DVD". Press a button on any.
  • Select the type of keyboard and good time.
  • Click repair your computer in the lower left corner.
  • Select Troubleshooting in choose an option screen.
  • In Troubleshooting screen, click Advanced options .
  • Click the automatic repair of the Advanced Options screen.
  • Then choose the operating system.
  • Windows 8 will then pick up questions on the hard drive and check that all required files are intact.

  If the problem persists, proceed to the next method.

  Method 2:

  Follow these steps to perform a system restore:

  • After you start your computer by using the Windows DVD or the system repair disc, a black screen is displayed with the gray text "Press any key to boot from CD or DVD". Press a button on any.
  • Select the type of keyboard and good time.
  • Click repair your computer in the lower left corner.
  • Select Troubleshooting in choose an option screen.
  • In troubleshooting screen, click Advanced options .
  • Select System Restore.

  For reference:

  http://support.Microsoft.com/kb/2756559/en-us

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Please let us know the results.

• Mac Pro black screen and the cursor on startup

  My Mac Pro won't start. He begins the start but stalls on a black screen.  None of the fixes recommended work (I tried them all THE). As I finally understood, it's el Capitan does not like more than one monitor (I have three). When I unplug the two monitors, it starts fine. Yosemite has worked well with three screens, ElCapitan started very well that if I unplugged one of you watching her. The latest version requires me to unplug both monitors so that it can start up.

  What specific Mac Pro?

  What specific graphics cards are installed?

  Are these Mac-Flash cards? They need additional drivers?

  How the monitors are connected?

• Windows 7 starts problems with black screen and the cursor because of power failure

  I'm on a Windows 7 64-bit Home Premium OS. Start-up problems arose after the power failure (accidentally unplugged the charger, the battery was not in place) during a video call in Skype. Accessories attached to the laptop at the time were a Logitech Webcam, a dongle Bluetooth, microphone and headphones.

  When starting my laptop Asus N81VP, he'll go as far as the 'Starting Windows' logo, then I meet a black screen with a mobile cursor. I don't then right click, CTRL + ALT + DELETE.

  I tried the things:

  Start Up Repair = "cannot automatically repair."

  System Restore = no available restore points

  Windows Memory Diagnostic = at 100%, no screen of detected problems, then black with mobile cursor

  Networking Mode Safe Mode/Safe = black screen with cursor mobile

  Activate video low resolution (640 x 480) = black screen with cursor mobile

  Good known Configuration = black screen with cursor mobile list

  Start Windows normally = black screen with cursor mobile

  Please help me. I've had this laptop for less than a year, and it would break my heart to have to re - format.

  You seem to have exhausted most of the options available in such cases, except two:
  D ' log in under a different account.
  -To restore your registry files manually. See below for more details.

  On your heart that could get broken: have you considered using the imaging facility that is integrated with Windows 7? You can find it in the control panel / backup and restore. This is somewhat marginal in the feature and it can be finicky, but it saved my butt several times.

  You can restore your registry files manually to a previous point through the steps described below. The process is complex and requires some careful typing. Ask a computer-savvy friend to help you if you lack experience in this field. Note that it may reset your password to a previous value.
  1. keep tapping F8 during the first phase of startup.
  2. Select repair in the menu that looks like this:
  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
  3 log in as administrator if you are prompted.
  4. Select repair when prompted.
  5. Select the command line in the menu that looks like this:
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7
  6. identify the correct drive letter for your Windows installation. It could be one drive other than c, but it will not X:. You do this by typing commands
  DIR C:\Win*
  Dir D:\Win*
  dir E:\Win*
  until you find the Windows folder.
  I'll call this "Q:" drive
  7 type these commands:
  CD /d Q:\windows\System32\config
  xcopy *. * Q:\MyRegBack\
  CD RegBack
  dir
  8. review the dates of the software, system, and SAM files. The files created before or after that is your problem?
  9. If they were made before the problem appeared, you can then type these commands:
  copy software / y...
  /y copy system...
  /y copy Sam...
  (the two points are part of each order)
  10. restart normally. If things don't work then you can go back by copying files from the original register of Q:\MyRegBack to Q:\Windows\System32\config.

• Videos YouTube won't play. The black screen and the pictures are the same.

  The videos do not play or load at all. Just like thumbnails. The comments section constantly says "loading". I have tried every thing on the site here to solve these problems. The only thing that has worked to be honest was trying to load Internet Explorer. Adblock Plus and Flash Player plugins are either removed or disabled. Tried to make a new profile and delete the folder in %AppData%. It works for awhile and then randomly the fact still.

  Things that CAN help with this problem. YouTube is the only site that does that when it comes to videos. Sites require that use flash sometimes will not play even if everything is clean installed. I have Nvidia Geforce experience working with shadowplay allowed to also record the Desktop connections to. Because it uses the h.24 codec, I thought it was clashing with him the origin of the problem. I can turn off shadowplay and reload the youtube page 2 to 3 times and the main video will play only.

  Finally, I let fall the other day, put everything back as it was and put the computer to sleep. When I woke up I decided what the Hey, ill youtube charge just for fun to see if it fixes as if by magic. Well, it does. So tonight its back to the drawing board again. I had noticed that wouldn't change items when twitch on my homepage from yahoo with the news. So I decided to try the webtools / tool to reload the network page. Fixed flash yahoo run of new articles but then my problem youtube is back! Ive a fire fox for as long as I can remember and never had any problems with it! If Ive come here, it means Ive gave up stubborn. I'm proud of myself on my own attachment issues, but this one has me so I yield.

  Here is a picture of attatched.

  Kind regards
  VADM anomaly

  You can view the log in the Web Console for error messages and network monitor (Firefox/tools > Web Developer) to see if the content does not load, or may be blocked.

  • https://developer.Mozilla.org/Tools/Web_Console
  • https://developer.Mozilla.org/Tools/Network_Monitor

  Use Ctrl + F5 or Ctrl + Shift + R to reload the page and bypass the cache to generate a new connection.

• Just bought a msi gtx 750 ti OC edition.when installed does not start, ends with a black screen and the cursor

  As indicated in the title, I bought a ti 750 gtx.

  N750Ti-2GD5/OC

  The machine had a 620 in gt and works very well with it in. When I install the ti 750 gtx, however, the boot system hangs on a black screen with cursor / underscores and a single beep.

  The system is a h8 1203, with a power of 460.

  I also have a gts 250, that also installs and works fine. Ive read a little, and there is a problem with this map and the hp system? something about the type of bios? I couldn't quite follow what has been said.

  Hello

  If you upgrade to Windows 8 (UEFI-mode Setup) and apply the BIOS posted updated so you should be able to work to the video card.

  Don't forget to create a set of external support of HP recovery before installing a new operating system.

• HPE-500f freezes black screen and the cursor at the top left

  My Pavilion Elite HPE-500f boots up to a white screen with the cursor in the upper left corner. He will not start in safe mode. Problem started when I left flash drive in USB that may be a coincidence. Started from CD's with the recovery disk, but which did not also. Run diagnostic F9 of the opening screen and it shows the error message "test of startup failed: error code BIOHD3;" No leave actiive.

  I can get it to run by pressing ESC at startup and even if the start of the hard drive is highlighted I have to press down arrow for CD player, then the button to the hard drive, and press ENTER. It will start normally. This process works every time, so it doesn't seem like a hard drive problem.

  Appreciate any help on this forum

  Hello

  If you do not, use another PC to create a rescue CD Windows 7.  Download the ISO from the link below.

  Windows 7 64 bit

  You must use an app like ImgBurn to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.  One time created, or if you already have this, insert the CD into the laptop and restart at the start of it.  Select repair.

  Select the "repair your computer" option and follow Option 2 in the guide on the link below to run the startup repair - you may need to run this 2 or 3 times.

  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  If the above does not help, take note of any error message you get during the procedure and include them with your next post.

  Kind regards

  DP - K

• Desktop does not - black screen with the cursor and access to Task Manager

  Well, I played recent MMO and to do this, I had to update my sound drivers and graphics. I managed to finish my first uninstall all the old drivers-flawless and it worked perfectly thereafter with no video issues (that I had before the uninstall, but nothing harmful to the system). Eventually however, I started to get some pop ups Windows 2008 C++ REDIS saying that atieclxx.exe had asked to be terminated in an unusual way. No problem, I close the error message and everything always works as it should. No random crashes.

  My problem is that wermgr.exe (I am fairly certain that this is the title, but I did not work right now), began leaving me with a black screen and the cursor when I connect. In most cases, I can open the Task Manager by pressing Ctrl + Alt + Delete, however, it sometimes won't start, and when I start to kill unnecessary tasks, they take some time to die. I know that black screens are often a defective start of explorer.exe, which manages office and file, browsers so I use the Task Manager to run it and it dies or continues to do nothing without making the office. Whenever this happens, wermgr.exe was running (Windows error handler). When I kill this task, which often has duplicates, I can finally get explorer.exe to load. I have the same problem with safe mode, except that the display shows the version of windows and the details in each corner until explorer.exe load finally. I've also had freezing issues long whenever Werfault.exe jump upward and the only thing that those fixed has been disable Werfault.exe in the services menu.
  It is clear to me that the windows error reporting programs consume a lot of the capacity of the CPU of my computer and they are probably the source of the biggest problems I'm having. I should stop start, or they are just neutral, awakened by a bigger problem?
  On a smaller note, C++ error is probably due to me not having is not the correct edition of the redistributable C++ installed, or perhaps too many distributions. The last edition, I have installed is 10.0.40219 of the x 86 and x 64 redistributable and runtimes (2010). Are the oldest, I installed some updates ATL and 5 2005 Redistributable (2 x 64 versions). Atieclxx.exe is the program having the pop-ups demand 'unusual termination. " The version of my ATI Radeon drivers are included in Version 2012.1116.1515.27190 of the AMD VISION Engine Control Center.
  Now, finally, I think it's useless, I'll give you my specs:
  OS: Windows 7 Home Premium, 64-bit
  Processor: AMD Athlon TF-20, 1.60 GHz
  RAM: 3.00 GB
  Model: Acer Aspire 5534
  BIOS: InsydeH2O V1.12
  Graphics card: ATI Radeon HD 3200, using aticfx64.dll and aticfx32.dll
  I do not believe that a reinstallation is necessary, because I got my computer in good enough condition that I can write this message and use it as usual, however, it's a nuisance to do, because it requires waiting a few minutes while the wermgr.exe process is stopped by the Task Manager.

  HiJack This help "fix selected", I removed the SmartShopper and BHO entry no name, as well as a few more suspicious looking files and those to the left of the old installs (windowblinds). I also deleted all entries in ø16 because I didn't need them and didn't like their operation. Then, I deleted two mistakes of R3, who looked extremely suspicious.

  IT'S FIXED NOW!
  I restarted and connected to be greeted with my office. The second csrss.exe is still underway, and atieclxx.exe works well as well. Although they appear to be the cause of the problem, because I am intimately familiar with the process of my computer, it is also clear that many of the comes from problems of registry and the programs that I have only half managed to uninstall. I hope this helps people to the problem in the future, and if my problem recur soon, I will return to this article with more information.
  As a final note, I was extremely impressed with HiJack this, because I used it for the first time in order to solve this problem. He kindly explained to me why he alerted me and what kind of problems listed that would cause a lot of things helped me to decide what to remove. Now I know why divert this is recommended everywhere on the internet as a diagnostic tool.
  To not appear as an advertising bot, but it's the tool that solved my problem for this, I have it suggests. in any case, good luck and I hope you can fix this problem yourself. With the help of google, an open mind and careful decision making, it is possible to solve anything. I do not recommend using a shotgun to do so ;)

• Start normal mode after windows xp bar charge it gives black screen and in safe mode it gives blue screen

  Victorinox original title: Black scree & blue screen...

  So my laptop that is running Windows xp, start in normal mode after windows xp bar charge it gives black screen and it stays like this, and in safe mode it gives blue screen, what can I do? I need your help atleast to save the files to my hard drive...

  Hello

  · What is the error code or error message that you receive when the computer starts in safe mode?

  · Were there any changes made on the computer before the show?

  · What is the number and the model of the computer?

  · Who is the service pack installed?

  Try the methods below:

  Method 1: Disconnect all the devices connected to the computer such as printers, scanners or USB hard drives and restart the computer and check if that helps.

  Method 2:

  Try to start your computer in last known good configuration. You can check the link for the procedure: how to start your computer by using last good known Windows XP Configuration: http://support.microsoft.com/kb/307852

  Method 3:

  You can follow the steps listed in the link: after the Windows Logo appears, or after you log on Windows, a Windows XP computer can display the wallpaper, a black screen or a blue screen: http://support.microsoft.com/kb/318027

• Everytime I try to log in its just goes to a black screen with the cursor on my laptop Windows 8.

  * Original title: Admin Login

  On my laptop Windows 8, I can't connect to my admin user or even use my administrative password. Whenever I try to open a session in his will just a black screen with the cursor, and when I try to use my password it dims the screen and I can't do anything. Is there anyway that I can fix this?

  I solved the problem by resetting my laptop using the recovery mode.

• When I was playing the game and my 3D PC show the black screen and the sound of noise.

  Hi Admin,
  When I was playing the game and my 3D PC show the black screen and the sound of noise. And then I can't move anything and I can restart only. What is this problem? I don't know why? Please help me what should I do.
  My PC specs are as follows

  Aspire M5800 (Q84MR375) Genuine Windows Vista® Home Premium, 64-bit, Intel Core 2 Quad processor Q8400 (2.66 GHz, 4 MB L2 Cache, bus front at 1333 MHz), 3 GB Ram, 750 GB S - ATA HDD, DVD SuperMulti Double Layer drive, Nvidia GeForce GT220 graphics (1 GB dedicated RAM) card, Wireless LAN, keyboard and wireless mouse with LCD 23 '' monitor.

  phoechan,
  More than likely if this started after you upgrade to Windows7 then you might have to update your hardware drivers.  Go to the websites of the manufacturers of hardware for your PC and get all the latest drivers for Windows 7 (video, sound, chipset, etc...).  If they don't have Windows 7 drivers you may have questions until they create them.  You can also try to boot your PC and also right click on the game .exe file and change the compatibility mode to Vista or XP.

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• My computer has a black screen and a cursor and there is no menu start more

  Original title: replay Vista operating system

  What I would like to know, is my computer only has a black screen and a cursor, there is no menu start, so I can stop and start a new installation of windows vista? If anyone can help please. I thank you very much for your time and have a fantastic day. Shawn

  Hello

  What changes have been made on your machine for there to be a black screen with a cursor?

  Rather than doing a clean install of your operating system, I suggest you do the following.

  Step 1:

  Remove all external devices (printer, USB flash drive), as appropriate, and start your computer again and check.

  Step 2:

  If this is little help, start your machine in safe mode and check if it starts on the desktop.

  Let us know the status of the issue.

  Azeez Nadeem - Microsoft Support [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Invalid product key, left my computer with a black screen and a cursor of the mouse on the boot.

  A few days ago, I tried to upgrade Windows 7 Home Premium (64 bit) to Windows 10 using the free update. Installation hung at 84% for 2 hours, then restarted, was unable to recover the installation and then could not get back to Win 7. This left us with a black screen and a cursor of the mouse on the boot. The computer would remain in this State for about 10 minutes and then reboot and repeat.

  Fortunately, or so I thought, I had a few CD Windows installation backup from the back to the era of digital river. So I thought I'd install fresh on my empty partition, copy my files and data, and then format the partition with the installation broken on.

  I did, but now he tells me that my product key is not valid and cannot be activated. The product key came on a real label on the PC when we bought it.

  The key is for X 16-96072. I installed X 17-58997 (Windows 7 Home Premium x 64 with SP1 (u)). I don't know what is the problem with the key? Should I have installed without the (u)?

  One key 25 digits grouped in 5 sequences of 5 characters not X 17-58997.

  To analyze and solve problems for Activation and Validation, we need to see a full copy of the diagnostic report produced by the MGADiag tool (download and save to the desktop -http://go.microsoft.com/fwlink/?linkid=52012 )
  Once downloaded, run the tool.
  Click on the button continue, after a short time, continue button will change to a copy button.
  Click the copy button in the tool (ignore the error at this stage) and then paste (with r-click and paste or Ctrl + V) in your message.