After system recovery question

Similar Questions

• Cannot install Office97pro after system recovery using windows XP. System does not seem to recognize the drive.

  After system recovery cannot reinstall dvd office97pro. It seems that windows XP does not recognize the program on the disk.  Tested the dvd on my computer laptop windows 7, charges fine. Help!

  Hi Fred Chandler,.

  1. What happens when you insert the DVD in the drive?
  2. You receive an error message?
  3. You are able to use the other DVDs on the computer?
  4. Do you have any third-party DVD burning software installed on the computer?

  If you are facing a similar problem with all DVDs on the computer, refer to the article below and then try the steps mentioned, check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

  If you face this problem with the Office 97 DVD then I would suggest that you post your request in the forums of Microsoft Office.

  http://answers.Microsoft.com/en-us/Office/Forum

• How can I recover the Photoshop 8 after system recovery? [was: bkupa]

  How can I recover the Photoshop 8 after system recovery

  Reinstall it properly:

  Direct download links for Adobe software

  Mylenium

• Problems installing software hp after system recovery system

  I just replaced the motherboard due to the failure in an hp g60. I tried using the recovery of the system since the partition and the computer reboots after about 20 seconds in the hp software installation process. Then the system recovery screen would jump upward to want to me again the whole process. After 3 times to do, I did a scan of seatools hard disk and it tested ok. Then I thought that maybe there was a file corrupted on the partition, so I ordered the hp recovery discs. I ran these discs today and I got almost 3 quarters thanks to the installation of the hp software when a screen poped and told him to end the windows session and the computer restarted again. When he started upward, poped system recovery window back up and asked me to do it again. I'm looking for any help/suggestions on this subject. Thank you.

  Hello

  This could be the problem as HP recovery disks check for a "tattoo" on the bios to make sure that the operating system is installed on the machine, that it was intended.  One way to confirm this would be to install an OS on a retail disc - even if you don't activate - just to see if this will load ok.

  Best wishes

  DP - K

• can not update xp or IE after system recovery

  I did a system restore on my computer XP 32 bit. I have not checked to see if he had 1 SP installed, but I had a disc for SP 2 and manually installed SP 3.
  I can't install WIndows updates, due to the fact that I need of IE 7 or higher. IE 7 won't install because I guess he needs updates of some sort? How can I solve this problem?

  I tried to install Service Pack 1, but it wouldn't work because I installed SP 3.

  Thank you for your help

  4. after recovery, your office is always show files that were there before the recovery?

  Describe the very next step you take after you have completed the recovery. The files are still there, but some are missing such as 2007 Microsoft Office and other programs, but my documents are still there

  This means that is non-destructive recovery of Compaq and have without doubt both times. I would say that a re - install destructive is in order and follow my previous instructions that were for a clean install. Note that this will destroy the data so if your data is important you must save it first, ideally twice in two separate devices. If you are worried about data loss, I suggest putting in the hands of a professional, but do not expect to take any responsibility for your data. If someone is able, they may not cover all the possibilities (e.g., disk failure) and we your data must be your responsibility.

  In the light of your PC is one that may require the patch from HP/Compaq AMD I have revised my instructions for you below...

  Print what you want from this Web site that you can access on the PC hit after the new installation. After the installation you're using IE6 that this site does not work with!

  Get these downloads (click the link) and have them on a CD or a USB key (ignore warnings from Microsoft gives you need to be an IT pro or using Windows updates in place)

  SP2 (only if your recovery is a "no service pack at all" XP or is a Media Center XP)

  SP3 (only if your recovery is pre - SP3)

  AMD patch (only if your recovery is pre - SP3)

  IE8 (do not leave Microsoft direct you to a later version, IE8 is as good as it gets for XP)

  Make sure you have your antivirus solutions and handy greater security as (CD/download).

  • Back up your data
  • Disconnect from the internet (remove the cable Ethernet or a wireless device?)
  • Disconnect all devices except the screen, keyboard and mouse.
  • Make the new facility (the driver installation should not be necessary for a resumption of Compaq)
  • Remove Norton (use the deletion tool that rocks of XP has suggested)
  • Install SP2 (only if there is no service pack at all after the recovery, or it is XP Media Center)
  • Install the patch from HP/Compaq AMD (if recovery is pre - SP3)
  • Install SP3 (if recovery is pre - SP3)
  • Install IE8
  • Install antivirus/security
  • To connect to the internet
  • Update antivirus/security
  • Windows Update
  • Install remaining desired hardware/software
  • Restore your data

  Do not use Windows updates or driver "detectives" update/install drivers.

  Do not try to use Windows Update, until SP3 is installed.

  Do not install IE8 or any other software as long as you are at SP3.

  Make sure to use restore points in case something goes 'shaped pear.

  Tricky

• RESULTS OF THE PRINTER ARE NOT READABLE AFTER SYSTEM RECOVERY

  HP Pavilion p6740f desktop computer. Windows 7 Home Premium 64-bit.

  PhotoSmart HP 6510

  After a system recovery recent everything works, except the printer does print to look like giberash.  Here's a sample:

  HN #$ () (1 + 29LYI

  Although the documents look good on the monitor, they print it.  It doesn't matter if the document is on Wordpad, Notepad, Word or PDF.

  Please tell me what is the problem, Joe

  I just use a program called REIMAGE to repair the files.  It worked very well, found the bad files and delete them and replaced the files with the new ones.  The printer works fine now.  REIMAGE is a great program!

• Installation of Windows Mail after system recovery

  Hello. I need help to set up Windows Mail after a system recovery. I have Vista Home premium. My ISP is Comcast, so I have a Comcast email address. I did a full backup on an external HD before the resumption. I have not used Windows Mail since Jan. 27. Since then, I've been access my mail on the site Web of Comcast.

  I need to know the correct sequence of steps to set up Windows mail. Is it to drag the contents of the folder from my outside to my computer? Do I need to configure the info from the first acct (pop etc.) before you transfer the contents of the folder? I want all my old mail book and the address in the new configuration. These seem to be backed up on my external.

  Also once I'm set up should I expect to see all letters sent since Jan. 27? I don't mind what happens. I just want to know what to expect.

  Thanks in advance for your help

  First, set up your account in Windows Mail.   If you want messages that you see in Windows Mail to remain available in Comcast web messaging, configure the account to leave messages on the server. When you click send/receive , it will download all of the messages that are stored on your Comcast email server.

  To import your old messages in Windows Mail, press ALT + F , click on import > Messages > Microsoft Windows Mail 7 > Next , find the mail backup folder and follow the instructions.  The old post will go into a folder called folder imported , and you can move it to other records there if you wish.

  By default, Windows Mail saves its messages in C:\Users\\AppData\Local\Microsoft\Windows Mail.  AppData is a hidden, so turn on the display of the hidden files and folders first.

  To import your contacts, copy them to the contacts saved to the new folder.  By default, Windows Vista stores contacts in C:\Users\\Contacts.

  Boulder computer Maven
  Most Microsoft Valuable Professional

• BIOS and system recovery question

  If we do a system recovery, bios back to an earlier version if it is updated after the date of recovery?

  N °

• Relocation of the PS CC trial after system recovery

  I have installed PS CC trial December 21, 2013. After a recovery system PS disappeared. I find no way to reinstall it at the time of the open trial.

  Run creative cloud cleaning tool , and reinstall.

  Mylenium

• HP Pavilion dv7 system recovery questions

  I tried a system recovery using the HP DVD sent to me earlier and I put the first disc in and fine, sometimes about to hundred 70ish then asking disc two, I insert the CD 2 and it carries up to 100% then it moves to "deploy the files required for the installation of recovery phase" but does not move 0%

  I tried to use the portable computers own system recovery, but it does not at all.

  Ive took records, re them, put disc back in and stillhad entered no chance.

  Any ideas on what I can do?

  Hi John,.

  You're welcome and good to hear that it's all sorted out

  All the best,

  DP - K

• Windows calendar entries lost after system recovery

  Yesterday, I had to do a full system recovery.  That in itself is not really a problem because I do a backup on a regular basis, and all the files have been restored, outside my Windows calendar entries.  I would have thought that they would be backed up with everything else.

  The beckup settings are standard Windows backup settings.

  If anyone has an idea where they can be restored from, it would be a great help.

  Thahaseena thanks for your advice.  Unfortunately, the ics. file doesn't seem to be in windows backup, but I found a way to include this in the future.  I showed the steps for others who may encounter the same problem:

  Click on a space vacuum calendar > file > Export > make sure that the file name is [your name] calendar > choose a folder you know is saved (e.g. Documents/General > save)

  You should do whenever you perform some new entries, but this as an operation 'save', and export default to the location you have chosen, making it even faster.

  The ics.file then I hope that automatically backs up your external storage next time you perform a backup.

  Di.

• where can I find the original trunk after system recovery

  I made a recvry of the system. I need to add the boot in the file.i start looked in c for the boot drive. I found it c/boot. so I added it to the to the the file start and rebooted. is that correct?

  also, I want theoriginal BIOS F.1B for MY LAPTOP - HP PAVILION DV7 - LM726AV.  WHERE TO FIND IT?

  THX.  KRIS.

  May depend on exactly what you mean by the system recovery

  I don't know what you're trying to achieve with 'boot' or what exactly you mean

  You can find drivers for your laptop from HP support specific to your model, you should be aware that bad update/modify the Bios can cause a dead PC

  BIOS F.1B is the bios updated the original was F.13

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5112006#N1749

• After system recovery recently my computer always crashes and support told me I have a virus

  Computer: HP Pavilion p6130y

  My computer started to slow down and freeze after about 1 week ago. Do normal functions and multitasking, that I have the computer completely freezes where I couldn't move my mouse and even ctrl alt delete doesn't work. I have to restart the computer manually and sometimes allowing my computer to load correctly. So I unplug the device and the computer then go back, and I could back into the computer.

  I tried several system restores to the previous points, but the problem continued. Finally, I decided to perform a full recovery of the system. I don't mind not all backup files or put them on flash drives.

  After that, I reinstalled just some of my basic programs I wanted (Chrome, Skype, AVG) and he did a few quick updates to Java, Adobe, etc.

  The problem continues. Where now if I have 6 tabs open Chrome, my computer would slow down and eventually freeze, making me even once having to manually restart the computer. I also noticed if the computer go to sleep that he wouldn't wake up and work, it would be frozen.

  I ran AVG virtually every hour to make sure I wasn't picking up any virus, but he'd always clean.

  I finally called HP support and they told me that I have some kind of Virus, but that he would not go in detail unless I paid for their services which I can't afford right now.

  After hearing it was a virus, I disconnected the computer from the internet, but continues to run. I can hear weird noises to beep-beeps and fan runs constantly. The beeps sounds where sounds I had never heard of my computer before... They were different, then the typical beeps you hear when the computer loads up.

  I have read as much info about it, but did not find much that relates to my problem and I'm really not tech savy enough to explore the computer myself and hopefully address them myself.

  Can anyone help? At this point, I'm worried about the same connect to the internet. Suggestions?

  Hello

  Step 1:

  I suggest you to download and run the latest Microsoft security on your computer Scanner and check if it helps:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  Note: the data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

  You can check if you face the same question in a different user account or a new user account. You can create a new user account on your computer and check.

  Step 2:

  Create a new user account-
  http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account

  Step 3:

  If you are not faced with the same question in a new user account, you can check the link and use the steps provided to fix a corrupted user - below profile
  http://Windows.Microsoft.com/en-us/Windows-Vista/fix-a-corrupted-user-profile

  Let us know if it helps!

• Cannot find my cd/dvd drive in windows Vista after system recovery

  I tried all the everything in this forum that I found, but I still can't my dvd player to show up anywhere there was here a few days and I had to perform a full recovery of the system and now its does not can someone please give me some ideas so I can use my dvd again drive?

  I have more upper and lower filters

  I am running sp2 and fixit program isn't helping me

  I have a HP Pavilion 9700US

  Hello

  Check with HP Support, their online documentation and drivers, and their known forums
  questions.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ----------------------------------------------------------------------------------------------------------

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• After system recovery driver problems

  After a total hard drive failure, I used the recovery disks to reinstall Windows XP Pro. Nine drivers are absent, and the customer support needed to help me find and install. The system is now updated to current levels and works very well. However two questions pilot apparently associated are:

  (1) when you start up the computer, a program called Apoint.exe is started from the STARTUP group. It does not end, but lies in the status bar at the bottom of the screen. When I click on it, I get a black screen with a symbol flashes in the upper left corner and a white square cursor. I can put end to the program with no problem apparent but would like to have complete normally or not run at all. Seems to be related to the touchpad driver.

  (2) from the start, something like 25 language files named Arabic.bin, etc. to let in the TEMP directory. They seem to be related to the Realtek Audio driver. I can delete them without apparent problem, but they come back the next time. Very annoying.

  oldrah

  uninstalling drivers, restart your computer and try the drivers from the link below:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-68007

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-67783

  PS: If you would like more information, please, type post (0687, 0769)