After that stright connected to iSCSI (initiator) Host cannot ping the server iSCSI (target), but the target can, why?

After that host on vSHere 4.0 strightly connected to iSCSI (initiator) host cannot ping the server iSCSI (target), but target can.  And iSCSI works well. I mean I can create and use the iSCSI disk, why? It makes me confused.

Thank you!

Geoarge,

iSCSI traffic uses a VMkernel port, instead of using the command 'ping', use 'vmkping '.

André

Tags: VMware

Similar Questions

  • How to prevent my Mac of disconnection after that I connected remotely from iPhone and then left the iPhone app?

    I use RemoterVNC on my iPhone to log remotely on my Mac at home so the children can use the computer without my go physically to the computer. (I admit, I am a bit lazy like that). However, lately when I launch RemoterVNC (on my iPhone), do the business of the connection, and then exit the application, the remote Mac began a disconnection. He also started doing this when I connect from my first Mac via screen sharing. It is a relatively recent behavior. Someone has an idea what setting I have (inadvertently) enabled to prevent the computer from automatically disconnect when the 'access app' is no longer active on the remote device?

    Go to System Preferences > energy saving > computer sleep > drag it FOREVER to prevent disconnection of your mac.

    Think simple.

  • ESX host cannot ping the default gateway.

    Hi Experts,

    I have connected ESX hosts to switch cisco as well by the ILO and other ports.

    Cisco switch configuration;

    int gig 1/0/21 and 1/0/13 gig and gig 1/0/14 are configured as access ports because they are carriers/tagging vLan as a 306.

    Cisco switch, I can ping the ip address of the ILO, but I can't ping the IP address management and vice versa.

    IP Managment

    10.197.204.10

    255.255.255.0

    10.197.204.1

    VLAN 306

    Attached the screenshot shown in the diagram.

    your help will be appreciated.

    Concerning

    Don't know what it is, but there must be something simple that you miss

    Let's go through each step of configuration for both ESXi network connections (ILO work already, so we do not touch).

    Check the configuration of switch port physical interface GigabitEthernet1/0/13 and 1/0/14.

    switchport access vlan 306

    switchport mode access

    spanning tree portfast

    Only connect the cable network for vmnic0 to host and make sure what vmnic0 presents itself as 'connected' in the DCUI

    Make sure the VLAN ID is empty.

    Make sure you then the IP settings are correct (IE without typos,...) and restart the management network from the main menu.

    André

  • Comments can ping host, but host cannot ping the prompt.

    Hello. I already asked this question in another discussion, but it has a different title, so I decided to ask my question in a new discussion.

    Host: Windows 7, 192.168.186.1, no gateway IP

    Client: Windows XP, 192.168.186.2, no gateway IP

    If the ping of the comments reached the host. But when I try to ping the host's comments, I get '100% packet loss. How it could be explained?

    I take a look at the Windows Firewall on computers and make sure that it is disabled.

  • The host cannot ping

    Hello

    I can't reach my host. What could be the problem?

    I am using Vmware Server 2.0.1 Build 156745

    Host: Windows XP Professional sp2

    IP:192.168.146.1 host (vmnet1)

    Hardware: Computer laptop Dell 630

    Comments: Linux

    CentOS 2.16.0

    GuestIP:192.168.146.120

    Comments cannot ping the host

    Host cannot ping the prompt

    I tried to configure the nat and the host only to connect. Nat could also be able to reach the external pages.

    I appreciate any ideas

    Is the fixed prompt on DHCP or IP?

    What network cards do you have on the host and bridged (vmnetcfg.exe run as administrator)?

    Is the physical card on the guest living/connected - sometimes to the life of a card NETWORK disconnected will no connectivity in the guest?

    Have you recently changed the VMware network in the host? If so, you will need to restart the VMware services or reboot the host.

    Is there a firewall clutter it?

    Is the card NETWORK connected to the prompt - it shouldn't be a red cross on the network icon in the list of the material in the center of the console pane when the virtual machine is selected in the left pane?

    The MAC address or virtual and physical adapters in the host and the single guest, that is not duplicated?

    If all this pans, can be helpful to remove the NETWORK card in the prompt and add a. Also, what type of NETWORK adapter is it in the guest - 'flexible' or 'e1000 '? Should be 'flexible' for Linux - post (tie) the .vmx doubt customers.

    --

    If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

  • After I loaded Turbo Tax 2011, after that I connect to my PC, I get a blank screen with only the cursor showing. I am on Windows Vista.

    After I loaded Turbo Tax 2011, after that I connect to my PC, I get a blank screen with only the cursor showing. I picked up at an earlier date and reloaded the software TT 3 times with the same result. I tried of caraa start windows Explorer by using the Task Manager, but it does not work.

    Hi AndyCantore,

    Follow these steps:

    Step 1: Start the computer in safe mode and check if the problem persists.

    Start your computer in safe mode

    http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

    Step 2: If the problem does not persist in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

    Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

  • I have a folder of files in local folders that keeps reappearing after that I erase it. I tried to fix the folder several times. Any suggestions?

    I have a folder of files in local folders that keeps reappearing after that I erase it. I tried to fix the folder several times. Any suggestions?

    This is the name of a folder? Who will be in a file name in your file system. Given his situation, is it possible or likely that the total path length exceeds the limit of the operating system?

    For example: http://windows.microsoft.com/en-gb/windows/file-names-extensions-faq#1TC=windows-7

    This is not to talk about any other limit which may be inherent in the way that Thunderbird uses names of files internally.

    In your position, I explore the Thunderbird profile and check paths, as they appear in the file manager. You should be able to remove all folders that are unwanted here also.

  • After that installation of 9.3 iPad will not activate, it has been restored, but still not turn on. The first owner does not know the password

    After that installation of 9.3 iPad will not activate, it has been restored, but still not turn on. The first owner does not know the password

    And this is not recognitze by any device, computer or iPhone 6plus.

    If you or the original owner did not have the password no one here or at Apple can help you.

  • After that I have enter my serial code # and select the location in which to install Lightroom, I click on install.  Windows asks if I want to leave, I say Yes.  Then it starts installing but quickly gives a screen Installation failed

    After that I have enter my serial code # and select the location in which to install Lightroom, I click on install.  Windows asks if I want to leave, I say Yes.  Then it starts installation but quickly gives a failed Installation display The error summary of files gives me no information.  Any ideas?

    Thank you, but I thought about it.  I have to select "Run as Administrator" on the installer so that it works correctly on Windows 8 Pro.  FYI just when it happens again.

  • I have the latest downloadable version of the LR5.  It crashed while it was perceived 1:1 uttered during an import. After a restart of the Win764(), it displays a message that LR has to leave because he cannot read the preview files and it will try to fix

    I have the latest downloadable version of the LR5.  It crashed while it was perceived 1:1 uttered during an import. After a restart of the Win764(), it shows a message that LR has to leave because he cannot read the preview files and it will try to fix it the next time's lance.  I get the same message to another and whenever he throws so I can't launch LR at all now.

    I get the preview of a file has been corrupted somehow.  Is it possible to fix this without having to build a new catalog?

    Use Windows Explorer to open the folder containing your catalog. You will see a folder with the extension .lrdata. You must remove this folder, and then restart the Lightroom. Lightroom will generate a new folder of previews.

  • VM management host cannot ping gateway or switch

    Hello


    We have a server Esx 5.0 with 3 vm on it. When I try to ping the management network of vm for my pc that I do not get an answer too trying to ping from the vmn console I can not ping to the gateway, but I can ping dns. However, I can rdp in vm servers and the ping to the gateway of each server, as well as newspapers in vsphere. We have a system with 2 voip VLAN, the other data and another for voice. Hosts and servers are all on the same cisco switch.

    VM management network

    IP - 192.168.1.6

    Sub - 255.255.255.0

    GW - 192.168.1.1

    DNS - 192.168.1.10

    Cisco switch - 192.168.1.3

    Data Vlan - 192.168.1.1

    Firewall - 192.168.1.2

    PC

    -cannot ping 192.168.1.6

    -can ping everything else

    From the console network management

    -cannot ping 192.168.1.1 a.3 or any pc

    -can ping 192.168.1.10

    It sounds like a switch problem but do not know how to fix it. The switch is a switch of cisco small business pro 8 ports

    Make sure that your routing has L3 to a defined network to get traffic to your host (192.168.1.0/24) network to any network it seeks to achieve. You did not show what the subnet for the PCs are so I'm not sure that the network is.

    Regarding the gateway ping, make sure that the echo ICMP message is enabled by the firewall so that ping responses can go to the host. If you still cannot ping the gateway with that on, there may be a larger problem with your connectivity.

  • Cannot ping the Virtual Machine by host

    Hi all,

    Please help, I use VMWare Workstation 6.5 and I have a physical operating system which is Windows XP SP2, I have a network card, but not connected to a physical switch, the IP address is 192.168.0.1. I installed a Virtual Machine using Microsoft Windows 2003 server as the operating system, promote as domain controller, install the DHCP, DNS service and assign an IP 192.168.0.2, no default gateway.

    My VMnet1 on physical operating system has an IP 192.168.204.1 and VMNet8 has an IP 192.168.126.1.

    The host, I cannot ping the 192.168.0.2 which is the IP address of the Virtual Machine. Even in the Virtual Machine, I can not ping 192.168.0.1 is the IP address of the host. From what I read, the physical and the virtual machine were connected with a virtual switch. Am I wrong?

    Any advice?

    Thanks in advance.

    They SEEM to be in different networks, you need search routing between them,... since they differnet networks...

    on the other

    they do host and the virtual machine on the same subnet / network for EXAMPLE: class C class network 192.168.200.0/24

    granting of points if my answer was helpful... Thank you > > > > > > > >

    concerning

    Joe

  • internal hosts cannot access the internet w / L2L configured tunnel

    The internal hosts behind the ASA cannot access the internet with a configured tunnel to L2L. The L2L tunnel is mounted and passing traffic correctly. However, the internal host cannot access the internet through the ASA. I think I have my NAT watered somewhere. I can't even a host statically mapped to the internet. It might be because I'm used to having a WAN IP to the external interface which differs by the CIDR block assigned by the ISP. In this case, it's all together, with the ASA outside interface occupying the first available address.

    We have been assigned a CIDR range x.x.x.64/28. x.x.x.65 is my front door and my first usable est.68, by the PSI (I guess what they utilisent.66 et.67 for internal use). External interface of the ASA est.68 and I'm trying to get NAT others. I'm Polo all DHCP clients internal and have some static entries as well. Below is the relevant NAT config. Yet once, all traffic passes above the tunnel properly, but not from inside to outside. If more information is needed, please advise.

    interface outside

    IP address x.x.x.68 255.255.255.240

    NAT-control

    Global x.x.x.69 - x.x.x.77 2 (outdoor)

    Global 1 x.x.x.78 (outside)

    NAT (inside) 0 access-list sheep

    NAT (inside) 1 10.10.10.0 255.255.255.0

    public static x.x.x.69 (inside, outside) STATIC_NAT_EXAMPLE netmask 255.255.255.255

    internal access-group interface inside

    Route outside 0.0.0.0 0.0.0.0 x.x.x.65 1

    internal to the 10.10.10.0 ip access list allow 255.255.255.0 any

    ! Remote LAN is 192.168.10.0/24

    access-list sheep extended ip 10.10.10.0 allow 255.255.255.0 192.168.10.0 255.255.255.0

    Can you post a "show sysopt run?

    Try this command to enable proxy arp.

    No outside sysopt noproxyarp

  • HP 15 laptop: dark screen appeared after that I connect

    DEAR HP,

    I CAN'T OPEN MY FIRST ACCOUNT HERE. HERE'S THE SCÉNARION. SHOWS THE START OF HP AND THE LOCK SCREEN. THEN IN OPERATION FOREST-IN MY FIRST ACCOUNT, I ENTER THE PASSWORD, AND THEN AFTER THAT, IT'S ALL DARK. NO FURTHER RESPONSE. SCREEN ALL BLACK. BUT I CAN ACCESS MY SECOND ACCOUNT EASILY. PLEASE HELP ME NOW. I NEED MY LAPTOP TO BE RIGHT SO THAT I CAN USE IT IN MY PAPER AND THESIS WORK. THANK YOU :-)

    Of

    EMC_22

    Hello

    Try this and let me know.

    Boot the computer normally and log.

    Black screen, hold down the ctrl and alt keys and press delete.

    Select Task Manager.

    At the bottom left, select details (if it is not already selected).

    Click in the header of column Nsoul to organize the processes in alphabetical order.

    Look for an entry called to run once Wrapper (RunOnce.exe) - If you see it listed, right-click on it and select end task.

    The office is now show?

    If this is the case, download Autoruns on the following link and save it in your downloads folder.

    http://download.sysinternals.com/files/Autoruns.zip

    When you have that, open your download folder, right-click on the folder zipped to Autoruns, select "extract all...". "and in the next window, click Extract.

    A new window will open displaying the extracted content.  The application you must launch is the 2nd in the list (in format autoruns 636ko) but this by right clicking on it and selecting 'Run as administrator' -click 'Yes' to the uac prompt.

    Scroll down the list until you find the entrance to RunOnce (it may well be 2 entries) and Remove the tick (s) in the box next to it.

    Restart computer and see if it boots now on the desktop.

    Kind regards

    DP - K

  • VMs that newly set up cannot ping the host

    A few days ago vSphere VMs worked well on nested host A that was vSphere, too. Then, install a vDS and place all hosts. He because of problem that guests could not ping each other. But, other virtual machines (I mean windows OS above) can always ping the host. So, moved the hosts of the vDS and removed the vDS, the problem is there. And implemented a few new virtual machines, what operating system are vSphere, too on the nested host a. They can only ping itself, but cannot ping on nested host A, too. Then, remove the data center and set up a new. the probel is still here.

    The problem should be soon after vDS, how can I solve this problem?

    the configuration of these new virtual machines are inpicture.

    my thought here, you forgot to activate rear promicious (security) on vSwitch0 & 1 after the migration, both of vNDS

    http://www.no-x.org

Maybe you are looking for

  • Mac book pro logging out despite the system preferences settings

    If my computer is turned on for more than 20 minutes without me touching the mouse/keyboard, I am prompted with a request to save my work before disconnection.  If I get bored of the command prompt, I get disconnected.  All of this is that despite wh

  • Ultiboard select HIERARCHICAL block

    Normal 0 false false false MicrosoftInternetExplorer4 / * Style Definitions * / table. MsoNormalTable {mso-style-name: "Table Normal" "; mso-knew-rowband-size: 0; mso-knew-colband-size: 0; mso-style - noshow:yes; mso-style-parent:" ";" mso-padding-al

  • What to associate "MS Search"?

    I have outlook and when I try to get an e-mail by using the search function it asks me to download it from the website of Ms. When I download it and try to open it, I wonder what program I would like to? Does anyone know how or what program to associ

  • Moving files from old p/c in XP to new p/c under Windows 7

    I have a six year old computer of 32-bit Pentium 4 HP, I have upgraded the memory to 2 GB and have replaced the original 80 GB hard drive with a 200 GB hard drive. I think about buying a new HP desktop with an Intel i5-2320 64-bit 8 GB 2 TB harddrive

  • Magic of the network stops nikon software to run!

    seems I find more problems with this software of each and everyday... it's slow (a lot) of vista ultimate 64 bit stop but is not only also in conflict with Nikon browser that many of us, the photographers use... http://support.nikontech.com/app/answe