After that windows update, the system stops without warning and can not perform restore

Similar Questions

• You Tube, after that 11 seconds the video stops, in all and is no sound through the speakers. No noise in the music of cd too

  For example: in You Tube, after 11 seconds the video stops, in all and is no sound through the speakers. No noise in the music of cd too.

  If you get no audio cd, youtube or anything else, you must first check in the volume control that you are using the sound card, you are connected, that nothing is on mute and volume is sufficient, or install the drivers for your sound card.

  Video YouTube can be that your internet connection is slow or too much peoole try to watch the same video, save it to your hard drive and then watch or, give him a minute or two to download in the buffer before you start watching.

• After that windows update, the resolution of my screen has been reduced.

  I can't return address. Re-installation of software has failed. What should do?

  Use system restore to go back to an earlier date at the beginning of the problem.  To run system restore, click Start-> programs-> Accessories-> System Tools-> system restore.  Click on the box that says show more restore points.

  Moreover, if you install option via Windows update drivers, that's how many people enter in this kind of situation.  You only need to update the drivers from the website of the manufacturer of your computer, and then only when you have a problem to solve.

  I hope this helps.  Good luck.

• Windows 7 Edition Home Premium. After that windows update will in a reboot loop

  Windows 7 Edition Home Premium. After that windows update KB982926 & KB982670, will in a reboot loop, 64 bit, Dell Studio XPS. I used F8 & restore to burst. Tried the update again with the same results. Silverlight & Net Framework updates

  Hi pbmass,

  I want to clarify if you are able to start the computer on the desktop after the system restore.

  Follow the steps mentioned below and then try to install the updates manually

  Step 1: Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Step 2: Run the fixit available in the link below to reset windows update components.

   

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

   

  Step 3: Disable the security software; Follow the steps mentioned in the link below

  Disable antivirus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Important: Activate security software once everything is done.

  Step 4: Download the update manually and then install them

  The .NET Framework 4 Client Profile is available on Windows Update

  http://support.Microsoft.com/kb/982670

  Description of the update for Silverlight:

  http://support.Microsoft.com/kb/982926

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• After that Windows update restarted as requested, by getting only now white screen

  After that Windows update restarted as requested, by getting only now white screen.

  Unable to set up windows

  I was able to boot in safe mode and restore that updated windows.  Then found that the monitor is released.  Again, everything is good

• Can't make a HD video, after that I updated the product? and there is that a message says it can't encode video and will have to change the settings to try again!

  Can't make a HD video, after that I updated the product? and there is that a message says it can't encode video and will have to change the settings to try again!

  jilll

  What version of Premiere Elements you use, what computer operating system?

  What would you update... have you had 12 and 12.1 updated or have you 13 and 13.1 updated? Or did you upgrade may 14 from a previous version?

  Where are you in the settings for your version where you get the message saying you cannot encode the video and you may need to change export settings?

  What is your planned export?

  Please explain, give more details.

  I will review your wire in the morning morning look to follow so that I can help you succeed in your Premiere Elements project.

  RTA

• I have installed and uninstalled SP6 from a CD and the CC PS repeatedly today and can not get either the version of the function.

  I have installed and uninstalled SP6 from a CD and the CC PS repeatedly today and can not get either the version of the function. I get the following messages: could not load actions because an unexpected end of file was encountered could not initialize Photoshop because an unexpected end of file was encountered could not initialize Photoshop because the preferences file was invalid (it has been deleted). I should have a clean install of programs. I tried one at a time in case they are somehow interfere between them.

  Try to run Photoshop and immediately press on and hold the keys Ctrl + Alt + Shift Windows CMD + Option_Shift Mac. Photoshop invite and ask you want to your preferences removed. Answer Yes.

• in applications, the loading mark keeps appearing and can not complete downloading the trial of Photoshop and Dreamweaver.

  in applications, the loading mark keeps appearing and can not complete downloading the trial of Photoshop and Dreamweaver.

  Please read https://forums.adobe.com/thread/1499014

  -try some steps such as changing browsers and disable your firewall

  -also clear the cache of your browser if you start with a fresh browser

  -check the file hosts for blocked entries https://forums.adobe.com/thread/1912777

  http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip.

  https://helpx.Adobe.com/creative-cloud/KB/creative-cloud-desktop-application-failed.html

  http://helpx.Adobe.com/creative-cloud/KB/failed-install-creative-cloud-desktop.html

• Satellite L25 - after that Windows update is unable to use the Wi - Fi button

  I have a S-1193 Satellite L25, caught a virus, and after a windows update, cannot use wi - fi on the front button.

  What I have to do is disable the adapter, turn it on, then re-boot.
  If I turned off the computer, I di everything again.

  This will make the button work? Or is there a setting that is always on?

  Hello

  > after a windows update, cannot use wi - fi on the front button
  Do you mean the button that launches Internet Explorer?

  According to your message the laptop doesn't connect to the WLan automatically and you will need to connect it manual to get the job of WLan.
  Is this right?

  I put t know how you have connected the laptop to your router, but usually, if you own Windows WLan zero configuration then you should make sure that the parameters to a called + connect when this network is in range. +

  Welcome them

• After that windows update in windows vista my i cannot connect to the net

  Hello

  I connect to a new internet provide a year back and has never faced these problems. Now for a month when I do my windows update I discconected on the net. the next day is starting to work again, and then I do the windows update, it disconnects again. I can't see also "NETWORK ADAPTER" in Device Manager. I tried to update the drivers of Gigabyte.com but does not seem to do anything. For more information, I used McAfee earlier too, but now I switched to Norton Anti Virus.Will this be causing a problem?

  This seems to be a problem with the modem DSL or ISP.
  Try to stop the DSL modem for 10 minutes and try to check if Internet works fine. Also contact you ISP to verify what they say about it.

  All the best

• Account reset / lost permissions after that Windows update?

  I am running Windows 7 on a HP Pavilion dv7 laptop. Recently, I conducted a regular update of Windows. Once the update has been completed, the my laptop rebooted and everything worked very well. Later that day, I turned off my computer laptop and turned on the next day morning. Everything was erased my desktop, documents, pictures, videos and so on. I can access all my programs by default start menu, such as Internet Explorer or Windows Movie Maker. However, if I go to my C drive and users, click on my account, I am always able to access all my documents, photos and videos that would be regularly on my computer desktop, documents, pictures, videos. When I open Google Chrome, it tells me that my profile has been reset by default and may not have the necessary permissions. When I open iTunes I get a popup that reads "Please wait while Windows configures iTunes."

  My account is the only account set up on my laptop, and he is an administrator.  What causes this and what could be done to set it back to normal? I am skeptical about the restoration of the system, because it can not solve the problem.

  In my humble OPINION, your problem resembles a corrupted user profile.  This is detected when you connect and a temporary, new user profile is created, which explains why you have been disconnected from your files.

  The first thing I would try would be a restoration of the system to a point in time before your problem.  Corruption is in your file 'ntuser.dat', then this should restore it.  If this does not work, then you must recover your user profile by using another method, such as:

  "Fix a corrupted user profile.

  <>http://Windows.Microsoft.com/en-us/Windows/fix-corrupted-user-profile#1TC=Windows-7 >

  HTH,

  JW

• After that windows update computer now hangs at the login screen, no error message, just restarts.

  I have tried safe mode, does the same thing; tried to use the Windows Vista disc to do a repair, no luck; also I tried restoring the system (from disk), no restore points however.
  The problem appeared after restarting the computer during the night.  The problem began to be able to connect, but the screen would go blank with just a pointer (KSOD).  Has tried some of the suggestions on this problem, including by eliminating sys newspapers, which did not work as well as reinstalling the video driver, with no luck.  Finally tried a system restore, returned 1 week (before the windows updates).  Now, the computer becomes just the login screen sits there for about 5-10 seconds then restarts immediately.

  I just had this happen to my laptop that has no external references. This is a new (September 09) ASUS K50ij with Vista 64-bit installed. I bought the Win 7 OS to replace, but have been waiting for the time to play with it... Last Monday, the update itself and invited to restart so I have done what I was busy with and enabled him to restart which is the only thing to do now... restart, the blue screen for a nano-second, then restart... etc. Same problem with safe mode and safe mode with networking, or with the box... anyway, someone very smart recommended that I use another computer (Fortunately, I have several) to download free Imgburn (which works easily), then get Ubuntu (Linux Operating System free download) burn image from the Ubuntu disc, put the disc in the drive of the computer crashed (there is a little hole next to the button you) can insert in a safety pin to release the door when the power is off) change the setting in the BIOS of the computer has crashed by restarting and pressing F2 until you get the menu BIOS... go to the start menu and choose Start from the CD, and then press ENTER. When the computer starts, it will see the drive and go to a menu to select the language, then next choice is "try Ubuntu without making any changes to the computer. It will boot the disk and allow you to view and copy ALL your files off the power on an external drive, which is what I did... including my Outlook .pst files that include all my saved emails my calendar and contacts, etc! WOOHOO! has got all my photos, documents, etc. The only thing that I didn't know how to get is my favorite... How to enter in the browser from another computer.

  If after this, an hour or more than make sure I got all the important data... I decided to see if anyone had a solution to this problem just fixing... I probably won't update again because Microsoft sends them and offers no solutions to the problems they have caused and nobody pays me for all the time I've lost get to get my stuff back and also to solve the problem they have caused. A update on my other laptop Win 7 zapped my outlook program and even reinstall it didn't solve this problem, even more work to do there, but looking in the files using Ubuntu's File Explorer, I found a hidden file that is used to repair the files .pst outlook called scanpst, or something that nearby.

  In any case, if someone has a solution to uninstall the recent update or to determine how it corrupted my user profile (which is the general consensus) please let me know.
  Thank you and good luck to you!

• When you click "Restart now" after Windows Update, the computer stops, does not restart

  When you click "Restart now" to a windows update... the computer cycle throughout the judgment... and not restart.

  * original title - problems with computer restart (ing) after the updates *.

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• Not able to boot after that windows update, just trying to install the number 3 setting 3, and then restart the computer. With the help of Windows Vista SP2

  Friday morning I wasn't able to boot my computer more. When I start my computer it won't seek to set a parameter nr 3 of 3. And then it restarts again. My computer tried to install some windows update settings the day before with no success. I Don t remember what it was. I got Vista SP2

  The same problem happends to my computer from friends four days, after she start a windows update installation. But it has solved its problem by using the Windows installation CD and use the repair tool.

  For me, my Windows installation CD I got from Dell does not work. Not the tool repair or startreparation. And I have no reference system to return.

  What should I do? I don't want to reinstall windows again, I have a lot of information on the computer I need to.

  All the world has noticed this problem?

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  See you soon.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work, try to make a Bootable ERD to do a Startup Repair:

  As is the case with most computers/laptops these days, they do not come with good Vista disc to repair only the recovery disks.

  As your grave in the category above, download the ISO on the link provided and make a bootdisk of it.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  You can make a tool to restart system, System Restore, etc. with it.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista repair disc.

  You can do a system restart tool, system, etc it restore.

  There is not a disk of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the ISP above Mathods to solve your problems, save your data using one of the methods below, and then reinstall Windows:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1 in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• After that Windows Update installation, some programs fail to open but take up to 25% of the CPU usage

  Hi I have a HP Probook 6470 b. After installation of the latest series of Windows updates my laptop fails to open the common programs such as Word 2010, Adobe Acrobat Pro and Internet Explorer 11. Other programs such as Excel 2010 and Chrome are not affected. Programs not just open, but on the control task manager, they are each taking up 25% CPU, which is the set of core.

  Strangely, on a machine identical to the work occurs the same problem but on a desktop computer, I can't reproduce the problem. With my laptop I use system restore and the problem goes away until Windows Update to run again - there are quite a few updates and I can't identify what the source of the problem.

  Everyone knows about this problem?

  Hello. In the end, I managed to get out. It was Microsoft EMET that was causing problems. Ultimately I unchecked all boxes and now all my programs work correctly. Strangely Chrome and Excel have been unchecked already which is the reason for which they worked.